| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1576288475-7606-1-git-send-email-vbadigan@codeaurora.org>
Date: Sat, 14 Dec 2019 07:24:34 +0530
From: Veerabhadrarao Badiganti <vbadigan@...eaurora.org>
To: adrian.hunter@...el.com, ulf.hansson@...aro.org,
robh+dt@...nel.org, mka@...omium.org
Cc: asutoshd@...eaurora.org, stummala@...eaurora.org,
sayalil@...eaurora.org, cang@...eaurora.org,
rampraka@...eaurora.org, linux-mmc@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-arm-msm@...r.kernel.org,
devicetree@...r.kernel.org,
Veerabhadrarao Badiganti <vbadigan@...eaurora.org>,
Andy Gross <agross@...nel.org>,
Bjorn Andersson <bjorn.andersson@...aro.org>,
Mark Rutland <mark.rutland@....com>
Subject: [PATCH V2] arm64: dts: qcom: sc7180: Add nodes for eMMC and SD card
Add sdhc instances for supporting eMMC and SD-card on sc7180.
The regulators should be in HPM state for proper functionality of
eMMC and SD-card. Updating corresponding regulators accordingly.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@...eaurora.org>
---
This depends on the patch series (dt support for sc7180):
https://lkml.org/lkml/2019/11/8/149
Also depends on documentation commit 2078158 (Present on mmc-next)
Changes since V1:
- Updated the regulator min, max voltages as per
eMMC/SD-card voltage requirements
- Enabled IOMMU for eMMC and SD-card.
- Added pull and drive strength to SD-card cd-gpio.
- Incorporated review comments by Matthias Kaehlcke.
---
arch/arm64/boot/dts/qcom/sc7180-idp.dts | 47 +++++++---
arch/arm64/boot/dts/qcom/sc7180.dtsi | 148 ++++++++++++++++++++++++++++++++
2 files changed, 183 insertions(+), 12 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
index 189254f..b6d4dc1 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
@@ -7,6 +7,7 @@
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include "sc7180.dtsi"
#include "pm6150.dtsi"
@@ -101,9 +102,9 @@
};
vreg_l12a_1p8: ldo12 {
- regulator-min-microvolt = <1696000>;
- regulator-max-microvolt = <1952000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l13a_1p8: ldo13 {
@@ -143,9 +144,9 @@
};
vreg_l19a_2p9: ldo19 {
- regulator-min-microvolt = <2696000>;
- regulator-max-microvolt = <3304000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
};
@@ -189,9 +190,9 @@
};
vreg_l6c_2p9: ldo6 {
- regulator-min-microvolt = <2696000>;
- regulator-max-microvolt = <3304000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l7c_3p0: ldo7 {
@@ -207,9 +208,9 @@
};
vreg_l9c_2p9: ldo9 {
- regulator-min-microvolt = <2952000>;
- regulator-max-microvolt = <3304000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l10c_3p3: ldo10 {
@@ -400,3 +401,25 @@
bias-pull-up;
};
};
+
+&sdhc_1 {
+ status = "ok";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc1_on>;
+ pinctrl-1 = <&sdc1_off>;
+ vmmc-supply = <&vreg_l19a_2p9>;
+ vqmmc-supply = <&vreg_l12a_1p8>;
+};
+
+&sdhc_2 {
+ status = "ok";
+
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&sdc2_on>;
+ pinctrl-1 = <&sdc2_off>;
+ vmmc-supply = <&vreg_l9c_2p9>;
+ vqmmc-supply = <&vreg_l6c_2p9>;
+
+ cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index 666e9b9..16de9b8 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -182,6 +182,32 @@
#power-domain-cells = <1>;
};
+ sdhc_1: sdhci@...000 {
+ compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5";
+ reg = <0 0x7c4000 0 0x1000>;
+ reg-names = "hc_mem";
+
+ interrupts = <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 644 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+
+ clocks = <&gcc GCC_SDCC1_APPS_CLK>,
+ <&gcc GCC_SDCC1_AHB_CLK>;
+ clock-names = "core", "iface";
+
+ iommus = <&apps_smmu 0x60 0x0>;
+
+ bus-width = <8>;
+ non-removable;
+
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+
+ status = "disabled";
+ };
+
qupv3_id_0: geniqup@...000 {
compatible = "qcom,geni-se-qup";
reg = <0 0x008c0000 0 0x6000>;
@@ -897,6 +923,128 @@
function = "qup15";
};
};
+
+ sdc1_on: sdc1-on {
+ clk {
+ pins = "sdc1_clk";
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ cmd {
+ pins = "sdc1_cmd";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ data {
+ pins = "sdc1_data";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ rclk {
+ pins = "sdc1_rclk";
+ bias-pull-down;
+ };
+ };
+
+ sdc1_off: sdc1-off {
+ clk {
+ pins = "sdc1_clk";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ cmd {
+ pins = "sdc1_cmd";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ data {
+ pins = "sdc1_data";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ rclk {
+ pins = "sdc1_rclk";
+ bias-pull-down;
+ };
+ };
+
+ sdc2_on: sdc2_on {
+ clk {
+ pins = "sdc2_clk";
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ cmd {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ data {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ sd-cd {
+ pins = "gpio69";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+ };
+
+ sdc2_off: sdc2_off {
+ clk {
+ pins = "sdc2_clk";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ cmd {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ data {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ sd-cd {
+ pins = "gpio69";
+ bias-disable;
+ drive-strength = <2>;
+ };
+ };
+ };
+
+ sdhc_2: sdhci@...4000 {
+ compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5";
+ reg = <0 0x08804000 0 0x1000>;
+ reg-names = "hc_mem";
+
+ interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+
+ clocks = <&gcc GCC_SDCC2_APPS_CLK>,
+ <&gcc GCC_SDCC2_AHB_CLK>;
+ clock-names = "core", "iface";
+
+ iommus = <&apps_smmu 0x80 0>;
+
+ bus-width = <4>;
+
+ status = "disabled";
};
qspi: spi@...c000 {
--
Qualcomm India Private Limited, on behalf of Qualcomm Innovation Center, Inc., is a member of Code Aurora Forum, a Linux Foundation Collaborative Project
Powered by blists - more mailing lists