Date:   Tue, 17 Dec 2019 09:00:27 -0700
From:   Jeffrey Hugo <jeffrey.l.hugo@...il.com>
To:     Vinod Koul <vkoul@...nel.org>
Cc:     Can Guo <cang@...eaurora.org>, asutoshd@...eaurora.org,
        nguyenb@...eaurora.org, Rajendra Nayak <rnayak@...eaurora.org>,
        linux-scsi@...r.kernel.org, kernel-team@...roid.com,
        saravanak@...gle.com, Mark Salyzyn <salyzyn@...gle.com>,
        Andy Gross <agross@...nel.org>,
        Alim Akhtar <alim.akhtar@...sung.com>,
        Avri Altman <avri.altman@....com>,
        Pedro Sousa <pedrom.sousa@...opsys.com>,
        "James E.J. Bottomley" <jejb@...ux.ibm.com>,
        "Martin K. Petersen" <martin.petersen@...cle.com>,
        "open list:ARM/QUALCOMM SUPPORT" <linux-arm-msm@...r.kernel.org>,
        open list <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v5 2/7] scsi: ufs-qcom: Add reset control support for host controller

On Tue, Dec 17, 2019 at 8:08 AM Vinod Koul <vkoul@...nel.org> wrote:
>
> On 17-12-19, 18:09, cang@...eaurora.org wrote:
> > On 2019-12-17 17:24, Vinod Koul wrote:
> > > Hi Can,
> > >
> > > On 17-12-19, 15:10, cang@...eaurora.org wrote:
> > > > On 2019-12-17 12:13, Vinod Koul wrote:
> > > > > Hi Can,
> > > > >
> > > > > On 17-12-19, 08:37, cang@...eaurora.org wrote:
> > > > > > On 2019-12-17 03:12, Jeffrey Hugo wrote:
> > > > > > > On Mon, Dec 16, 2019 at 12:05 PM Vinod Koul <vkoul@...nel.org> wrote:
> > > > > > > >
> > > > > > > > Hi Can,
> > > > > > > >
> > > > > > > > On 14-11-19, 22:09, Can Guo wrote:
> > > > > > > > > Add reset control for host controller so that host controller can be reset
> > > > > > > > > as required in its power up sequence.
> > > > > > > >
> > > > > > > > I am seeing a regression on UFS on SM8150-mtp with this patch. I think
> > > > > > > > Jeff is seeing same one lenove laptop on 8998.
> > > > > > >
> > > > > > > Confirmed.
> > > > > > >
> > > > > > > >
> > > > > > > > 845 does not seem to have this issue and only thing I can see is
> > > > > > > > that on
> > > > > > > > sm8150 and 8998 we define reset as:
> > > > > > > >
> > > > > > > >                         resets = <&gcc GCC_UFS_BCR>;
> > > > > > > >                         reset-names = "rst";
> > > > > > > >
> > > > > >
> > > > > > Hi Jeffrey and Vinod,
> > > > > >
> > > > > > Thanks for reporting this. May I know what kind of regression do you
> > > > > > see on
> > > > > > 8150 and 8998?
> > > > > > BTW, do you have reset control for UFS PHY in your DT?
> > > > > > See 71278b058a9f8752e51030e363b7a7306938f64e.
> > > > > >
> > > > > > FYI, we use reset control on all of our platforms and it is
> > > > > > a must during our power up sequence.
> > > > >
> > > > > Yes we do have this and additionally both the DTS describe a 'rst' reset
> > > > > and this patch tries to use this.
> > > > >
> > > > > Can you please tell me which platform this was tested on how the reset
> > > > > was described in DT
> > > > >
> > > > > Thanks
> > > >
> > > > Hi Vinod,
> > > >
> > > > If you are using the 8998's DT present on upstream, you may also
> > > > need to
> > > > enable
> > > > device reset on your platform. (We usually do a device reset before
> > > > call
> > > > ufshcd_hba_enable())
> > > > Given that 845 works fine, it may be the difference you have with
> > > > 845. 845
> > > > has device
> > > > reset support ready in upstream code, you can check sdm845-mtp.dts.
> > > > It is same for 8150, which is a lack of device reset support in
> > > > upstream
> > > > code base.
> > >
> > > I am using 8150mtp and you can see the DTS at [1]
> > > with this patch I get phy timeout error
> > >
> > > [    2.532594] qcom-qmp-phy 1d87000.phy: phy initialization timed-out
> > >
> > > If i revert this patch the Timeout goes away. UFS node for this platform
> > > is enabled in [2] and [3]
> > >
> > > I did add the GPIO as well for testing but that doesnt work, only thing
> > > that makes it work is rename the reset line to something other that
> > > 'rst'
> > >
> > > I found that with this patch the reset is invoked twice, not sure why!
> > >
> > > The 845 does not define a reset 'rst' but both 8150 and 8998 define
> > > that!
> > >
> > > [1]:
> > > https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/log/?h=for-next
> > > [2]:
> > > https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/commit/?h=for-next&id=3834a2e92229ef26d30de28acb698b2b23d3e397
> > > [3]:
> > > https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/commit/?h=for-next&id=3e5bf28d2c3981f949e848eec8a60e0b9b61189d
> > > >
> > > > To enable UFS device reset, please see
> > > > 1. https://lore.kernel.org/linux-arm-msm/20190828191756.24312-4-bjorn.andersson@linaro.org/
> > > > 2. 53a5372ce326116f3e3d3f1d701113b2542509f4
> > >
> > > Yes both are added for UFS and I am testing with these..
> > > >
> > > > FYI, I tested the patch on 8250 and its family platforms. In my
> > > > build, I
> > > > ported
> > > > change in #2 to my code base (in your case, make change to
> > > > drivers/pinctrl/qcom/pinctrl-msm8998.c) and enable the GPIO in DT like
> > > > sdm845-mtp.dts
> > >
> > > Please see drivers/pinctrl/qcom/pinctrl-sm8150.c upstream
> > >
> > > >         reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
> > >
> > > Yup, added:
> > >
> > >         reset-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>;
> >
> > Hi Vinod,
> >
> > What do you mean by the reset is invoked twice?
> >
> > Renaming 'rst' to something else equals disabling this patch.
> >
> > You said 845 has not this problem, I thought you tested the patch on 845
> > with
> > the same 'rst' defined on 8998 and 8150. If 'rst' is not present in 845's
> > DT,
> > it means this patch has no impact on 845.
>
> To clarify: This problem is not seen in 845 with upstream kernel ie
> 5.5-rc1 but regression is observed in sm8150 and 8998 (Jeff)
>
> And if I add the reset line to 845 (i am testing on dragon board
> RB3, I am seeing same issue here as well)
> --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> @@ -1374,6 +1374,8 @@
>                         lanes-per-direction = <2>;
>                         power-domains = <&gcc UFS_PHY_GDSC>;
>                         #reset-cells = <1>;
> +                       resets = <&gcc GCC_UFS_PHY_BCR>;
> +                       reset-names = "rst";
>
>                         iommus = <&apps_smmu 0x100 0xf>;
>
>
> And on boot i am seeing UFS failing:
>
> [    3.205567] qcom-qmp-phy 88eb000.phy: Registered Qcom-QMP phy
> [    3.215440] ufshcd-qcom 1d84000.ufshc: ufshcd_populate_vreg: Unable to find vdd-hba-supply regulator, assuming enabled
> [    3.226315] ufshcd-qcom 1d84000.ufshc: ufshcd_populate_vreg: Unable to find vccq-supply regulator, assuming enabled
> [    3.236844] ufshcd-qcom 1d84000.ufshc: ufshcd_populate_vreg: Unable to find vccq2-supply regulator, assuming enabled
> [    3.257053] scsi host0: ufshcd
> [    3.275109] qcom-qmp-phy 1d87000.phy: phy initialization timed-out
> [    3.283677] qcom_rpmh TCS Busy, retrying RPMH message send: addr=0x40904
> [    3.290508] phy phy-1d87000.phy.0: phy poweron failed --> -110
> [    3.296407] ufshcd-qcom 1d84000.ufshc: ufs_qcom_power_up_sequence: phy power on failed, ret = -110
> [    3.360851] ufshcd-qcom 1d84000.ufshc: Controller enable failed
> [    3.366838] ufshcd-qcom 1d84000.ufshc: Host controller enable failed
>
> > Actually, in our code base, we are not using phy-qcom-qmp.c. Instead,
> > we are using phy-qcom-ufs.c. phy-qcom-ufs.c is the one we use in all of our
> > mobile projects. Although both have the same functionality,
> > but in phy-qcom-ufs.c, the PCS ready bit polling timeout is 1000000us,
> > while in phy-qcom-qmp.c the PCS ready bit polling timeout is 1000us.
> > Would you mind give below change a try?
>
> Sure and this seems to do the trick on 845 with resets defined, Jeff can
> you try this on your laptop

I'm attaching a complete log of the failure I see.

Increasing PHY_INIT_COMPLETE_TIMEOUT to the indicated value appears to
fix the issue for me.

>
> But I dont get same result on sm8150-mtp, i am still seeing timeout with
> 1000000us.
>
> The bigger question is why is the reset causing the timeout to be
> increased for sdm845 and not to work in case of sm8150!
>
> > FYI, I tried the opposite change on my board (decrease the PCS polling
> > timeout
> > used in phy-qcom-ufs.c), I did see PCS polling timeout, which is the same
> > failure
> > you encountered.
> >
> > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c
> > b/drivers/phy/qualcomm/phy-qcom-qmp.c
> > index 39e8deb..0ee9149 100644
> > --- a/drivers/phy/qualcomm/phy-qcom-qmp.c
> > +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
> > @@ -66,7 +66,7 @@
> >  /* QPHY_V3_PCS_MISC_CLAMP_ENABLE register bits */
> >  #define CLAMP_EN                               BIT(0) /* enables i/o
> > clamp_n */
> >
> > -#define PHY_INIT_COMPLETE_TIMEOUT              1000
> > +#define PHY_INIT_COMPLETE_TIMEOUT              1000000
> >  #define POWER_DOWN_DELAY_US_MIN                        10
> >  #define POWER_DOWN_DELAY_US_MAX                        11
> >
> > On 845, if there is 'rst'
> >
> > Thanks.
>
> --
> ~Vinod

View attachment "dmesg.txt" of type "text/plain" (53264 bytes)

Powered by blists - more mailing lists