Message-Id: <20191219183212.850879550@linuxfoundation.org>
Date:   Thu, 19 Dec 2019 19:33:11 +0100
From:   Greg Kroah-Hartman <gregkh@...uxfoundation.org>
To:     linux-kernel@...r.kernel.org
Cc:     Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
        stable@...r.kernel.org,
        Kai-Heng Feng <kai.heng.feng@...onical.com>,
        Alan Stern <stern@...land.harvard.edu>
Subject: [PATCH 4.4 083/162] usb: Allow USB device to be warm reset in suspended state

From: Kai-Heng Feng <kai.heng.feng@...onical.com>

commit e76b3bf7654c3c94554c24ba15a3d105f4006c80 upstream.

On Dell WD15 dock, sometimes USB ethernet cannot be detected after plugging
cable to the ethernet port, the hub and roothub get runtime resumed and
runtime suspended immediately:
...
[  433.315169] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0
[  433.315204] usb usb4: usb auto-resume
[  433.315226] hub 4-0:1.0: hub_resume
[  433.315239] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10202e2, return 0x10343
[  433.315264] usb usb4-port1: status 0343 change 0001
[  433.315279] xhci_hcd 0000:3a:00.0: clear port1 connect change, portsc: 0x10002e2
[  433.315293] xhci_hcd 0000:3a:00.0: Get port status 4-2 read: 0x2a0, return 0x2a0
[  433.317012] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[  433.422282] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343
[  433.422307] usb usb4-port1: do warm reset
[  433.422311] usb 4-1: device reset not allowed in state 8
[  433.422339] hub 4-0:1.0: state 7 ports 2 chg 0002 evt 0000
[  433.422346] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343
[  433.422356] usb usb4-port1: do warm reset
[  433.422358] usb 4-1: device reset not allowed in state 8
[  433.422428] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 0 status  = 0xf0002e2
[  433.422455] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 1 status  = 0xe0002a0
[  433.422465] hub 4-0:1.0: hub_suspend
[  433.422475] usb usb4: bus auto-suspend, wakeup 1
[  433.426161] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[  433.466209] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[  433.510204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[  433.554051] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[  433.598235] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[  433.642154] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[  433.686204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[  433.730205] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[  433.774203] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[  433.818207] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[  433.862040] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[  433.862053] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[  433.862077] xhci_hcd 0000:3a:00.0: xhci_suspend: stopping port polling.
[  433.862096] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001
[  433.862312] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_suspend: 0
[  433.862445] xhci_hcd 0000:3a:00.0: PME# enabled
[  433.902376] xhci_hcd 0000:3a:00.0: restoring config space at offset 0xc (was 0x0, writing 0x20)
[  433.902395] xhci_hcd 0000:3a:00.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100403)
[  433.902490] xhci_hcd 0000:3a:00.0: PME# disabled
[  433.902504] xhci_hcd 0000:3a:00.0: enabling bus mastering
[  433.902547] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001
[  433.902649] pcieport 0000:00:1b.0: PME: Spurious native interrupt!
[  433.902839] xhci_hcd 0000:3a:00.0: Port change event, 4-1, id 3, portsc: 0xb0202e2
[  433.902842] xhci_hcd 0000:3a:00.0: resume root hub
[  433.902845] xhci_hcd 0000:3a:00.0: handle_port_status: starting port polling.
[  433.902877] xhci_hcd 0000:3a:00.0: xhci_resume: starting port polling.
[  433.902889] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[  433.902891] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0
[  433.902919] usb usb4: usb wakeup-resume
[  433.902942] usb usb4: usb auto-resume
[  433.902966] hub 4-0:1.0: hub_resume
...

As Mathias pointed out, the hub enters Cold Attach Status state and
requires a warm reset. However usb_reset_device() bails out early when
the device is in suspended state, as its callers port_event() and
hub_event() don't always resume the device.

Since there's nothing wrong to reset a suspended device, allow
usb_reset_device() to do so to solve the issue.

Signed-off-by: Kai-Heng Feng <kai.heng.feng@...onical.com>
Acked-by: Alan Stern <stern@...land.harvard.edu>
Cc: stable <stable@...r.kernel.org>
Link: https://lore.kernel.org/r/20191106062710.29880-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@...uxfoundation.org>

---
 drivers/usb/core/hub.c |    5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -5554,7 +5554,7 @@ re_enumerate_no_bos:
 
 /**
  * usb_reset_device - warn interface drivers and perform a USB port reset
- * @udev: device to reset (not in SUSPENDED or NOTATTACHED state)
+ * @udev: device to reset (not in NOTATTACHED state)
  *
  * Warns all drivers bound to registered interfaces (using their pre_reset
  * method), performs the port reset, and then lets the drivers know that
@@ -5582,8 +5582,7 @@ int usb_reset_device(struct usb_device *
 	struct usb_host_config *config = udev->actconfig;
 	struct usb_hub *hub = usb_hub_to_struct_hub(udev->parent);
 
-	if (udev->state == USB_STATE_NOTATTACHED ||
-			udev->state == USB_STATE_SUSPENDED) {
+	if (udev->state == USB_STATE_NOTATTACHED) {
 		dev_dbg(&udev->dev, "device reset not allowed in state %d\n",
 				udev->state);
 		return -EINVAL;

Powered by blists - more mailing lists