| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <a2445a16-651c-457c-9e3c-23899c639a1a@ti.com>
Date: Tue, 24 Dec 2019 15:40:20 +0530
From: Kishon Vijay Abraham I <kishon@...com>
To: Remi Pommarel <repk@...plefau.lt>, Yue Wang <yue.wang@...ogic.com>,
Lorenzo Pieralisi <lorenzo.pieralisi@....com>,
Andrew Murray <andrew.murray@....com>,
Kevin Hilman <khilman@...libre.com>,
Martin Blumenstingl <martin.blumenstingl@...glemail.com>,
Neil Armstrong <narmstrong@...libre.com>
CC: Jerome Brunet <jbrunet@...libre.com>,
<linux-kernel@...r.kernel.org>, <linux-pci@...r.kernel.org>,
<linux-amlogic@...ts.infradead.org>
Subject: Re: [PATCH v2 1/3] phy: amlogic: Add Amlogic AXG MIPI/PCIE PHY Driver
Hi,
On 24/12/19 3:15 AM, Remi Pommarel wrote:
> This adds support for the MIPI PHY also needed for PCIE found in the
> Amlogic AXG SoC Family.
>
> MIPI or PCIE selection is done by the #phy-cells, making the mode
> static and exclusive.
>
> For now only PCIE fonctionality is supported.
>
> This PHY will be used to replace the mipi_enable clock gating logic
> which was mistakenly added in the clock subsystem. This also activate
> a non documented band gap bit in those registers that allows reliable
> PCIE clock signal generation on AXG platforms.
>
> Signed-off-by: Remi Pommarel <repk@...plefau.lt>
> ---
> drivers/phy/amlogic/Kconfig | 11 ++
> drivers/phy/amlogic/Makefile | 1 +
> drivers/phy/amlogic/phy-meson-axg-mipi-pcie.c | 176 ++++++++++++++++++
> 3 files changed, 188 insertions(+)
> create mode 100644 drivers/phy/amlogic/phy-meson-axg-mipi-pcie.c
>
> diff --git a/drivers/phy/amlogic/Kconfig b/drivers/phy/amlogic/Kconfig
> index af774ac2b934..1eeb75d018e3 100644
> --- a/drivers/phy/amlogic/Kconfig
> +++ b/drivers/phy/amlogic/Kconfig
> @@ -59,3 +59,14 @@ config PHY_MESON_G12A_USB3_PCIE
> Enable this to support the Meson USB3 + PCIE Combo PHY found
> in Meson G12A SoCs.
> If unsure, say N.
> +
> +config PHY_MESON_AXG_MIPI_PCIE
> + tristate "Meson AXG MIPI + PCIE PHY driver"
> + default ARCH_MESON
> + depends on OF && (ARCH_MESON || COMPILE_TEST)
> + select GENERIC_PHY
> + select MFD_SYSCON
> + help
> + Enable this to support the Meson MIPI + PCIE PHY found
> + in Meson AXG SoCs.
> + If unsure, say N.
> diff --git a/drivers/phy/amlogic/Makefile b/drivers/phy/amlogic/Makefile
> index 11d1c42ac2be..2167330a0ae8 100644
> --- a/drivers/phy/amlogic/Makefile
> +++ b/drivers/phy/amlogic/Makefile
> @@ -4,3 +4,4 @@ obj-$(CONFIG_PHY_MESON_GXL_USB2) += phy-meson-gxl-usb2.o
> obj-$(CONFIG_PHY_MESON_G12A_USB2) += phy-meson-g12a-usb2.o
> obj-$(CONFIG_PHY_MESON_GXL_USB3) += phy-meson-gxl-usb3.o
> obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE) += phy-meson-g12a-usb3-pcie.o
> +obj-$(CONFIG_PHY_MESON_AXG_MIPI_PCIE) += phy-meson-axg-mipi-pcie.o
> diff --git a/drivers/phy/amlogic/phy-meson-axg-mipi-pcie.c b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie.c
> new file mode 100644
> index 000000000000..006aa8cdfc47
> --- /dev/null
> +++ b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie.c
> @@ -0,0 +1,176 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Amlogic AXG MIPI + PCIE PHY driver
> + *
> + * Copyright (C) 2019 Remi Pommarel <repk@...plefau.lt>
> + */
> +#include <linux/module.h>
> +#include <linux/phy/phy.h>
> +#include <linux/regmap.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/platform_device.h>
> +#include <dt-bindings/phy/phy.h>
> +
> +#define HHI_MIPI_CNTL0 0x00
> +#define HHI_MIPI_CNTL0_COMMON_BLOCK GENMASK(31, 28)
> +#define HHI_MIPI_CNTL0_ENABLE BIT(29)
> +#define HHI_MIPI_CNTL0_BANDGAP BIT(26)
> +#define HHI_MIPI_CNTL0_DECODE_TO_RTERM GENMASK(15, 12)
> +#define HHI_MIPI_CNTL0_OUTPUT_EN BIT(3)
> +
> +#define HHI_MIPI_CNTL1 0x01
> +#define HHI_MIPI_CNTL1_CH0_CML_PDR_EN BIT(12)
> +#define HHI_MIPI_CNTL1_LP_ABILITY GENMASK(5, 4)
> +#define HHI_MIPI_CNTL1_LP_RESISTER BIT(3)
> +#define HHI_MIPI_CNTL1_INPUT_SETTING BIT(2)
> +#define HHI_MIPI_CNTL1_INPUT_SEL BIT(1)
> +#define HHI_MIPI_CNTL1_PRBS7_EN BIT(0)
> +
> +#define HHI_MIPI_CNTL2 0x02
> +#define HHI_MIPI_CNTL2_CH_PU GENMASK(31, 25)
> +#define HHI_MIPI_CNTL2_CH_CTL GENMASK(24, 19)
> +#define HHI_MIPI_CNTL2_CH0_DIGDR_EN BIT(18)
> +#define HHI_MIPI_CNTL2_CH_DIGDR_EN BIT(17)
> +#define HHI_MIPI_CNTL2_LPULPS_EN BIT(16)
> +#define HHI_MIPI_CNTL2_CH_EN(n) BIT(15 - (n))
> +#define HHI_MIPI_CNTL2_CH0_LP_CTL GENMASK(10, 1)
> +
> +struct phy_axg_mipi_pcie_priv {
> + struct phy *phy;
> + unsigned int mode;
> + struct regmap *regmap;
> +};
> +
> +static const struct regmap_config phy_axg_mipi_pcie_regmap_conf = {
> + .reg_bits = 8,
> + .val_bits = 32,
> + .reg_stride = 4,
> + .max_register = HHI_MIPI_CNTL2,
> +};
> +
> +static int phy_axg_mipi_pcie_power_on(struct phy *phy)
> +{
> + struct phy_axg_mipi_pcie_priv *priv = phy_get_drvdata(phy);
> +
> + /* MIPI not supported yet */
> + if (priv->mode != PHY_TYPE_PCIE)
> + return 0;
> +
> + regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> + HHI_MIPI_CNTL0_BANDGAP, HHI_MIPI_CNTL0_BANDGAP);
> +
> + regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> + HHI_MIPI_CNTL0_ENABLE, HHI_MIPI_CNTL0_ENABLE);
> + return 0;
> +}
> +
> +static int phy_axg_mipi_pcie_power_off(struct phy *phy)
> +{
> + struct phy_axg_mipi_pcie_priv *priv = phy_get_drvdata(phy);
> +
> + /* MIPI not supported yet */
> + if (priv->mode != PHY_TYPE_PCIE)
> + return 0;
> +
> + regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> + HHI_MIPI_CNTL0_BANDGAP, 0);
> + regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> + HHI_MIPI_CNTL0_ENABLE, 0);
> + return 0;
> +}
> +
> +static int phy_axg_mipi_pcie_init(struct phy *phy)
> +{
> + return 0;
> +}
> +
> +static int phy_axg_mipi_pcie_exit(struct phy *phy)
> +{
> + return 0;
> +}
> +
> +static const struct phy_ops phy_axg_mipi_pcie_ops = {
> + .init = phy_axg_mipi_pcie_init,
> + .exit = phy_axg_mipi_pcie_exit,
> + .power_on = phy_axg_mipi_pcie_power_on,
> + .power_off = phy_axg_mipi_pcie_power_off,
> + .owner = THIS_MODULE,
> +};
> +
> +static struct phy *phy_axg_mipi_pcie_xlate(struct device *dev,
> + struct of_phandle_args *args)
> +{
> + struct phy_axg_mipi_pcie_priv *priv = dev_get_drvdata(dev);
> + unsigned int mode;
> +
> + if (args->args_count != 1) {
> + dev_err(dev, "invalid number of arguments\n");
> + return ERR_PTR(-EINVAL);
> + }
> +
> + mode = args->args[0];
> +
> + /* MIPI mode is not supported yet */
> + if (mode != PHY_TYPE_PCIE) {
> + dev_err(dev, "invalid phy mode select argument\n");
> + return ERR_PTR(-EINVAL);
> + }
> +
> + priv->mode = mode;
> + return priv->phy;
> +}
> +
> +static int phy_axg_mipi_pcie_probe(struct platform_device *pdev)
> +{
> + struct phy_provider *pphy;
> + struct device *dev = &pdev->dev;
> + struct phy_axg_mipi_pcie_priv *priv;
> + struct device_node *np = dev->of_node;
> + int ret;
> +
> + priv = devm_kmalloc(dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + /* Get the hhi system controller node */
> + priv->regmap = syscon_node_to_regmap(of_get_parent(dev->of_node));
> + if (IS_ERR(priv->regmap)) {
> + dev_err(dev, "failed to get HHI regmap\n");
> + return PTR_ERR(priv->regmap);
> + }
> +
> + priv->phy = devm_phy_create(dev, np, &phy_axg_mipi_pcie_ops);
> + if (IS_ERR(priv->phy)) {
> + ret = PTR_ERR(priv->phy);
> + if (ret != -EPROBE_DEFER)
> + dev_err(dev, "failed to create PHY\n");
> + return ret;
> + }
> +
> + phy_set_drvdata(priv->phy, priv);
> + dev_set_drvdata(dev, priv);
> + pphy = devm_of_phy_provider_register(dev, phy_axg_mipi_pcie_xlate);
> +
> + return PTR_ERR_OR_ZERO(pphy);
> +}
> +
> +static const struct of_device_id phy_axg_mipi_pcie_of_match[] = {
> + {
> + .compatible = "amlogic,axg-mipi-pcie-phy",
Is there a dt-binding documentation for this?
Thanks
Kishon
Powered by blists - more mailing lists