| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20200122185610.131930-4-bryan.odonoghue@linaro.org>
Date: Wed, 22 Jan 2020 18:55:54 +0000
From: Bryan O'Donoghue <bryan.odonoghue@...aro.org>
To: linux-arm-msm@...r.kernel.org, linux-usb@...r.kernel.org,
gregkh@...uxfoundation.org, jackp@...eaurora.org, balbi@...nel.org,
bjorn.andersson@...aro.org
Cc: linux-kernel@...r.kernel.org, Shawn Guo <shawn.guo@...aro.org>,
Andy Gross <agross@...nel.org>,
Kishon Vijay Abraham I <kishon@...com>,
Philipp Zabel <p.zabel@...gutronix.de>,
Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@...il.com>,
Bryan O'Donoghue <bryan.odonoghue@...aro.org>
Subject: [PATCH v3 03/19] phy: qualcomm: Add Synopsys Hi-Speed USB PHY driver
From: Shawn Guo <shawn.guo@...aro.org>
Adds Qualcomm QCS404 Hi-Speed USB PHY driver support. This PHY is usually
is usually paired with Synopsys DWC3 USB controllers on Qualcomm SoCs.
[bod: Updated qcom_snps_hsphy_set_mode to match new method signature
Added disjunct on mode > 0
Removed regulator_set_voltage() in favour of setting floor in dts
Removed 'snps' and '28nm' from driver name]
Signed-off-by: Shawn Guo <shawn.guo@...aro.org>
Cc: Andy Gross <agross@...nel.org>
Cc: Bjorn Andersson <bjorn.andersson@...aro.org>
Cc: Kishon Vijay Abraham I <kishon@...com>
Cc: Philipp Zabel <p.zabel@...gutronix.de>
Cc: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@...il.com>
Cc: linux-arm-msm@...r.kernel.org
Cc: linux-kernel@...r.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@...aro.org>
---
drivers/phy/qualcomm/Kconfig | 10 +
drivers/phy/qualcomm/Makefile | 1 +
drivers/phy/qualcomm/phy-qcom-qcs404-usb-hs.c | 415 ++++++++++++++++++
3 files changed, 426 insertions(+)
create mode 100644 drivers/phy/qualcomm/phy-qcom-qcs404-usb-hs.c
diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
index e46824da29f6..cc3f2bb01ad1 100644
--- a/drivers/phy/qualcomm/Kconfig
+++ b/drivers/phy/qualcomm/Kconfig
@@ -91,3 +91,13 @@ config PHY_QCOM_USB_HSIC
select GENERIC_PHY
help
Support for the USB HSIC ULPI compliant PHY on QCOM chipsets.
+
+config PHY_QCOM_QCS404_USB_HS
+ tristate "Qualcomm QCS404 Hi-Speed USB PHY driver"
+ depends on ARCH_QCOM || COMPILE_TEST
+ depends on EXTCON || !EXTCON # if EXTCON=m, this cannot be built-in
+ select GENERIC_PHY
+ help
+ Enable this to support the Qualcomm QCS404 USB Hi-Speed PHY driver.
+ This driver supports the Hi-Speed PHY which is usually paired with
+ either the ChipIdea or Synopsys DWC3 USB IPs on MSM SOCs.
diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
index 283251d6a5d9..a4a3b21240fa 100644
--- a/drivers/phy/qualcomm/Makefile
+++ b/drivers/phy/qualcomm/Makefile
@@ -10,3 +10,4 @@ obj-$(CONFIG_PHY_QCOM_UFS_14NM) += phy-qcom-ufs-qmp-14nm.o
obj-$(CONFIG_PHY_QCOM_UFS_20NM) += phy-qcom-ufs-qmp-20nm.o
obj-$(CONFIG_PHY_QCOM_USB_HS) += phy-qcom-usb-hs.o
obj-$(CONFIG_PHY_QCOM_USB_HSIC) += phy-qcom-usb-hsic.o
+obj-$(CONFIG_PHY_QCOM_QCS404_USB_HS) += phy-qcom-qcs404-usb-hs.o
diff --git a/drivers/phy/qualcomm/phy-qcom-qcs404-usb-hs.c b/drivers/phy/qualcomm/phy-qcom-qcs404-usb-hs.c
new file mode 100644
index 000000000000..0ea7c32941dd
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qcs404-usb-hs.c
@@ -0,0 +1,415 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2009-2018, Linux Foundation. All rights reserved.
+ * Copyright (c) 2018-2020, Linaro Limited
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_graph.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+/* PHY register and bit definitions */
+#define PHY_CTRL_COMMON0 0x078
+#define SIDDQ BIT(2)
+#define PHY_IRQ_CMD 0x0d0
+#define PHY_INTR_MASK0 0x0d4
+#define PHY_INTR_CLEAR0 0x0dc
+#define DPDM_MASK 0x1e
+#define DP_1_0 BIT(4)
+#define DP_0_1 BIT(3)
+#define DM_1_0 BIT(2)
+#define DM_0_1 BIT(1)
+
+enum hsphy_voltage {
+ VOL_NONE,
+ VOL_MIN,
+ VOL_MAX,
+ VOL_NUM,
+};
+
+enum hsphy_vreg {
+ VDD,
+ VDDA_1P8,
+ VDDA_3P3,
+ VREG_NUM,
+};
+
+struct hsphy_init_seq {
+ int offset;
+ int val;
+ int delay;
+};
+
+struct hsphy_data {
+ const struct hsphy_init_seq *init_seq;
+ unsigned int init_seq_num;
+};
+
+struct hsphy_priv {
+ void __iomem *base;
+ struct clk_bulk_data *clks;
+ int num_clks;
+ struct reset_control *phy_reset;
+ struct reset_control *por_reset;
+ struct regulator_bulk_data vregs[VREG_NUM];
+ const struct hsphy_data *data;
+ enum phy_mode mode;
+};
+
+static int qcom_snps_hsphy_set_mode(struct phy *phy, enum phy_mode mode,
+ int submode)
+{
+ struct hsphy_priv *priv = phy_get_drvdata(phy);
+
+ priv->mode = PHY_MODE_INVALID;
+
+ if (mode > 0)
+ priv->mode = mode;
+
+ return 0;
+}
+
+static void qcom_snps_hsphy_enable_hv_interrupts(struct hsphy_priv *priv)
+{
+ u32 val;
+
+ /* Clear any existing interrupts before enabling the interrupts */
+ val = readb(priv->base + PHY_INTR_CLEAR0);
+ val |= DPDM_MASK;
+ writeb(val, priv->base + PHY_INTR_CLEAR0);
+
+ writeb(0x0, priv->base + PHY_IRQ_CMD);
+ usleep_range(200, 220);
+ writeb(0x1, priv->base + PHY_IRQ_CMD);
+
+ /* Make sure the interrupts are cleared */
+ usleep_range(200, 220);
+
+ val = readb(priv->base + PHY_INTR_MASK0);
+ switch (priv->mode) {
+ case PHY_MODE_USB_HOST_HS:
+ case PHY_MODE_USB_HOST_FS:
+ case PHY_MODE_USB_DEVICE_HS:
+ case PHY_MODE_USB_DEVICE_FS:
+ val |= DP_1_0 | DM_0_1;
+ break;
+ case PHY_MODE_USB_HOST_LS:
+ case PHY_MODE_USB_DEVICE_LS:
+ val |= DP_0_1 | DM_1_0;
+ break;
+ default:
+ /* No device connected */
+ val |= DP_0_1 | DM_0_1;
+ break;
+ }
+ writeb(val, priv->base + PHY_INTR_MASK0);
+}
+
+static void qcom_snps_hsphy_disable_hv_interrupts(struct hsphy_priv *priv)
+{
+ u32 val;
+
+ val = readb(priv->base + PHY_INTR_MASK0);
+ val &= ~DPDM_MASK;
+ writeb(val, priv->base + PHY_INTR_MASK0);
+
+ /* Clear any pending interrupts */
+ val = readb(priv->base + PHY_INTR_CLEAR0);
+ val |= DPDM_MASK;
+ writeb(val, priv->base + PHY_INTR_CLEAR0);
+
+ writeb(0x0, priv->base + PHY_IRQ_CMD);
+ usleep_range(200, 220);
+
+ writeb(0x1, priv->base + PHY_IRQ_CMD);
+ usleep_range(200, 220);
+}
+
+static void qcom_snps_hsphy_enter_retention(struct hsphy_priv *priv)
+{
+ u32 val;
+
+ val = readb(priv->base + PHY_CTRL_COMMON0);
+ val |= SIDDQ;
+ writeb(val, priv->base + PHY_CTRL_COMMON0);
+}
+
+static void qcom_snps_hsphy_exit_retention(struct hsphy_priv *priv)
+{
+ u32 val;
+
+ val = readb(priv->base + PHY_CTRL_COMMON0);
+ val &= ~SIDDQ;
+ writeb(val, priv->base + PHY_CTRL_COMMON0);
+}
+
+static int qcom_snps_hsphy_power_on(struct phy *phy)
+{
+ struct hsphy_priv *priv = phy_get_drvdata(phy);
+ int ret;
+
+ ret = regulator_bulk_enable(VREG_NUM, priv->vregs);
+ if (ret)
+ return ret;
+ ret = clk_bulk_prepare_enable(priv->num_clks, priv->clks);
+ if (ret)
+ goto err_disable_regulator;
+ qcom_snps_hsphy_disable_hv_interrupts(priv);
+ qcom_snps_hsphy_exit_retention(priv);
+
+ return 0;
+
+err_disable_regulator:
+ regulator_bulk_disable(VREG_NUM, priv->vregs);
+
+ return ret;
+}
+
+static int qcom_snps_hsphy_power_off(struct phy *phy)
+{
+ struct hsphy_priv *priv = phy_get_drvdata(phy);
+
+ qcom_snps_hsphy_enter_retention(priv);
+ qcom_snps_hsphy_enable_hv_interrupts(priv);
+ clk_bulk_disable_unprepare(priv->num_clks, priv->clks);
+ regulator_bulk_disable(VREG_NUM, priv->vregs);
+
+ return 0;
+}
+
+static int qcom_snps_hsphy_reset(struct hsphy_priv *priv)
+{
+ int ret;
+
+ ret = reset_control_assert(priv->phy_reset);
+ if (ret)
+ return ret;
+
+ usleep_range(10, 15);
+
+ ret = reset_control_deassert(priv->phy_reset);
+ if (ret)
+ return ret;
+
+ usleep_range(80, 100);
+
+ return 0;
+}
+
+static void qcom_snps_hsphy_init_sequence(struct hsphy_priv *priv)
+{
+ const struct hsphy_data *data = priv->data;
+ const struct hsphy_init_seq *seq;
+ int i;
+
+ /* Device match data is optional. */
+ if (!data)
+ return;
+
+ seq = data->init_seq;
+
+ for (i = 0; i < data->init_seq_num; i++, seq++) {
+ writeb(seq->val, priv->base + seq->offset);
+ if (seq->delay)
+ usleep_range(seq->delay, seq->delay + 10);
+ }
+}
+
+static int qcom_snps_hsphy_por_reset(struct hsphy_priv *priv)
+{
+ int ret;
+
+ ret = reset_control_assert(priv->por_reset);
+ if (ret)
+ return ret;
+
+ /*
+ * The Femto PHY is POR reset in the following scenarios.
+ *
+ * 1. After overriding the parameter registers.
+ * 2. Low power mode exit from PHY retention.
+ *
+ * Ensure that SIDDQ is cleared before bringing the PHY
+ * out of reset.
+ */
+ qcom_snps_hsphy_exit_retention(priv);
+
+ /*
+ * As per databook, 10 usec delay is required between
+ * PHY POR assert and de-assert.
+ */
+ usleep_range(10, 20);
+ ret = reset_control_deassert(priv->por_reset);
+ if (ret)
+ return ret;
+
+ /*
+ * As per databook, it takes 75 usec for PHY to stabilize
+ * after the reset.
+ */
+ usleep_range(80, 100);
+
+ return 0;
+}
+
+static int qcom_snps_hsphy_init(struct phy *phy)
+{
+ struct hsphy_priv *priv = phy_get_drvdata(phy);
+ int ret;
+
+ ret = qcom_snps_hsphy_reset(priv);
+ if (ret)
+ return ret;
+
+ qcom_snps_hsphy_init_sequence(priv);
+
+ ret = qcom_snps_hsphy_por_reset(priv);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static const struct phy_ops qcom_snps_hsphy_ops = {
+ .init = qcom_snps_hsphy_init,
+ .power_on = qcom_snps_hsphy_power_on,
+ .power_off = qcom_snps_hsphy_power_off,
+ .set_mode = qcom_snps_hsphy_set_mode,
+ .owner = THIS_MODULE,
+};
+
+static const char * const qcom_snps_hsphy_clks[] = {
+ "ref",
+ "phy",
+ "sleep",
+};
+
+static int qcom_snps_hsphy_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct phy_provider *provider;
+ struct hsphy_priv *priv;
+ struct phy *phy;
+ int ret;
+ int i;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(priv->base))
+ return PTR_ERR(priv->base);
+
+ priv->num_clks = ARRAY_SIZE(qcom_snps_hsphy_clks);
+ priv->clks = devm_kcalloc(dev, priv->num_clks, sizeof(*priv->clks),
+ GFP_KERNEL);
+ if (!priv->clks)
+ return -ENOMEM;
+
+ for (i = 0; i < priv->num_clks; i++)
+ priv->clks[i].id = qcom_snps_hsphy_clks[i];
+
+ ret = devm_clk_bulk_get(dev, priv->num_clks, priv->clks);
+ if (ret)
+ return ret;
+
+ priv->phy_reset = devm_reset_control_get_exclusive(dev, "phy");
+ if (IS_ERR(priv->phy_reset))
+ return PTR_ERR(priv->phy_reset);
+
+ priv->por_reset = devm_reset_control_get_exclusive(dev, "por");
+ if (IS_ERR(priv->por_reset))
+ return PTR_ERR(priv->por_reset);
+
+ priv->vregs[VDD].supply = "vdd";
+ priv->vregs[VDDA_1P8].supply = "vdda1p8";
+ priv->vregs[VDDA_3P3].supply = "vdda3p3";
+
+ ret = devm_regulator_bulk_get(dev, VREG_NUM, priv->vregs);
+ if (ret)
+ return ret;
+
+ /* Get device match data */
+ priv->data = device_get_match_data(dev);
+
+ phy = devm_phy_create(dev, dev->of_node, &qcom_snps_hsphy_ops);
+ if (IS_ERR(phy))
+ return PTR_ERR(phy);
+
+ phy_set_drvdata(phy, priv);
+
+ provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (IS_ERR(provider))
+ return PTR_ERR(provider);
+
+ ret = regulator_set_load(priv->vregs[VDDA_1P8].consumer, 19000);
+ if (ret < 0)
+ return ret;
+
+ ret = regulator_set_load(priv->vregs[VDDA_3P3].consumer, 16000);
+ if (ret < 0)
+ goto unset_1p8_load;
+
+ return 0;
+
+unset_1p8_load:
+ regulator_set_load(priv->vregs[VDDA_1P8].consumer, 0);
+
+ return ret;
+}
+
+/*
+ * The macro is used to define an initialization sequence. Each tuple
+ * is meant to program 'value' into phy register at 'offset' with 'delay'
+ * in us followed.
+ */
+#define HSPHY_INIT_CFG(o, v, d) { .offset = o, .val = v, .delay = d, }
+
+static const struct hsphy_init_seq init_seq_qcs404[] = {
+ HSPHY_INIT_CFG(0xc0, 0x01, 0),
+ HSPHY_INIT_CFG(0xe8, 0x0d, 0),
+ HSPHY_INIT_CFG(0x74, 0x12, 0),
+ HSPHY_INIT_CFG(0x98, 0x63, 0),
+ HSPHY_INIT_CFG(0x9c, 0x03, 0),
+ HSPHY_INIT_CFG(0xa0, 0x1d, 0),
+ HSPHY_INIT_CFG(0xa4, 0x03, 0),
+ HSPHY_INIT_CFG(0x8c, 0x23, 0),
+ HSPHY_INIT_CFG(0x78, 0x08, 0),
+ HSPHY_INIT_CFG(0x7c, 0xdc, 0),
+ HSPHY_INIT_CFG(0x90, 0xe0, 20),
+ HSPHY_INIT_CFG(0x74, 0x10, 0),
+ HSPHY_INIT_CFG(0x90, 0x60, 0),
+};
+
+static const struct hsphy_data hsphy_data_qcs404 = {
+ .init_seq = init_seq_qcs404,
+ .init_seq_num = ARRAY_SIZE(init_seq_qcs404),
+};
+
+static const struct of_device_id qcom_snps_hsphy_match[] = {
+ { .compatible = "qcom,qcs404-usb-hsphy", .data = &hsphy_data_qcs404, },
+ { },
+};
+MODULE_DEVICE_TABLE(of, qcom_snps_hsphy_match);
+
+static struct platform_driver qcom_snps_hsphy_driver = {
+ .probe = qcom_snps_hsphy_probe,
+ .driver = {
+ .name = "qcom-qcs404-usb-hsphy",
+ .of_match_table = qcom_snps_hsphy_match,
+ },
+};
+module_platform_driver(qcom_snps_hsphy_driver);
+
+MODULE_DESCRIPTION("Qualcomm QCS404 Hi-Speed USB PHY driver");
+MODULE_LICENSE("GPL v2");
--
2.25.0
Powered by blists - more mailing lists