linux-kernel - [PATCH V2 7/9] mmc: mmci: add volt

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite for Android: free password hash cracker in your pocket

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <20200128090636.13689-8-ludovic.barre@st.com>
Date:   Tue, 28 Jan 2020 10:06:34 +0100
From:   Ludovic Barre <ludovic.barre@...com>
To:     Ulf Hansson <ulf.hansson@...aro.org>,
        Rob Herring <robh+dt@...nel.org>
CC:     <srinivas.kandagatla@...aro.org>,
        Maxime Coquelin <mcoquelin.stm32@...il.com>,
        Alexandre Torgue <alexandre.torgue@...com>,
        <linux-arm-kernel@...ts.infradead.org>,
        <linux-kernel@...r.kernel.org>, <devicetree@...r.kernel.org>,
        <linux-mmc@...r.kernel.org>,
        <linux-stm32@...md-mailman.stormreply.com>,
        Ludovic Barre <ludovic.barre@...com>
Subject: [PATCH V2 7/9] mmc: mmci: add volt_switch callbacks

A variant may need to define some actions before and after
a voltage switch.

This patch adds 2 voltage switch callbacks in mmci_host_ops:
-pre_sig_volt_switch allows to prepare voltage switch before to
 sent the SD_SWITCH_VOLTAGE command (cmd11).
-post_sig_volt_switch callback allows to define specific action after
 regulator set voltage.

Signed-off-by: Ludovic Barre <ludovic.barre@...com>
---
 drivers/mmc/host/mmci.c | 8 ++++++++
 drivers/mmc/host/mmci.h | 2 ++
 2 files changed, 10 insertions(+)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index d0a041c9e6cd..24e630183ed4 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -22,6 +22,7 @@
 #include <linux/mmc/pm.h>
 #include <linux/mmc/host.h>
 #include <linux/mmc/card.h>
+#include <linux/mmc/sd.h>
 #include <linux/mmc/slot-gpio.h>
 #include <linux/amba/bus.h>
 #include <linux/clk.h>
@@ -1217,6 +1218,9 @@ mmci_start_command(struct mmci_host *host, struct mmc_command *cmd, u32 c)
 		writel_relaxed(clks, host->base + MMCIDATATIMER);
 	}
 
+	if (host->ops->pre_sig_volt_switch && cmd->opcode == SD_SWITCH_VOLTAGE)
+		host->ops->pre_sig_volt_switch(host);
+
 	if (/*interrupt*/0)
 		c |= MCI_CPSM_INTERRUPT;
 
@@ -1830,6 +1834,7 @@ static int mmci_get_cd(struct mmc_host *mmc)
 
 static int mmci_sig_volt_switch(struct mmc_host *mmc, struct mmc_ios *ios)
 {
+	struct mmci_host *host = mmc_priv(mmc);
 	int ret = 0;
 
 	if (!IS_ERR(mmc->supply.vqmmc)) {
@@ -1849,6 +1854,9 @@ static int mmci_sig_volt_switch(struct mmc_host *mmc, struct mmc_ios *ios)
 			break;
 		}
 
+		if (!ret && host->ops && host->ops->post_sig_volt_switch)
+			ret = host->ops->post_sig_volt_switch(host, ios);
+
 		if (ret)
 			dev_warn(mmc_dev(mmc), "Voltage switch failed\n");
 	}
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index ddcdfb827996..c3bc0a38d4cb 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -377,6 +377,8 @@ struct mmci_host_ops {
 	void (*set_clkreg)(struct mmci_host *host, unsigned int desired);
 	void (*set_pwrreg)(struct mmci_host *host, unsigned int pwr);
 	bool (*busy_complete)(struct mmci_host *host, u32 status, u32 err_msk);
+	void (*pre_sig_volt_switch)(struct mmci_host *host);
+	int (*post_sig_volt_switch)(struct mmci_host *host, struct mmc_ios *ios);
 };
 
 struct mmci_host {
-- 
2.17.1