linux-kernel - [PATCH] serial: ar933x_uart: set UART_CS_{RX,TX}_READY

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [day] [month] [year] [list]

Message-ID: <20200207095335.GA179836@makrotopia.org>
Date:   Fri, 7 Feb 2020 11:53:35 +0200
From:   Daniel Golle <daniel@...rotopia.org>
To:     linux-serial@...r.kernel.org, linux-kernel@...r.kernel.org
Cc:     Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
        Jiri Slaby <jslaby@...e.com>,
        Chuanhong Guo <gch981213@...il.com>,
        Eitan Cohen <eitan@...t-semadar.com>,
        Ori Gofen <origofen@...il.com>
Subject: [PATCH] serial: ar933x_uart: set UART_CS_{RX,TX}_READY_ORIDE

On AR934x this UART is usually not initialized by the bootloader
as it is only used as a secondary serial port while the primary
UART is a newly introduced NS16550-compatible.
In order to make use of the ar933x-uart on AR934x without RTS/CTS
hardware flow control, one needs to set the
UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this
UART is used as primary/console, the bootloader on AR934x typically
doesn't set those bits.
Setting them explicitely on AR933x should not do any harm, so just
set them unconditionally.

Tested-by: Chuanhong Guo <gch981213@...il.com>
Signed-off-by: Daniel Golle <daniel@...rotopia.org>
---
 drivers/tty/serial/ar933x_uart.c | 8 ++++++++
 1 file changed, 8 insertions(+)

--- a/drivers/tty/serial/ar933x_uart.c
+++ b/drivers/tty/serial/ar933x_uart.c
@@ -328,6 +328,10 @@ static void ar933x_uart_set_termios(stru
 	ar933x_uart_rmw_set(up, AR933X_UART_CS_REG,
 			    AR933X_UART_CS_HOST_INT_EN);
 
+	/* enable RX and TX ready overide */
+	ar933x_uart_rmw_set(up, AR933X_UART_CS_REG,
+		AR933X_UART_CS_TX_READY_ORIDE | AR933X_UART_CS_RX_READY_ORIDE);
+
 	/* reenable the UART */
 	ar933x_uart_rmw(up, AR933X_UART_CS_REG,
 			AR933X_UART_CS_IF_MODE_M << AR933X_UART_CS_IF_MODE_S,
@@ -460,6 +464,10 @@ static int ar933x_uart_startup(struct ua
 	ar933x_uart_rmw_set(up, AR933X_UART_CS_REG,
 			    AR933X_UART_CS_HOST_INT_EN);
 
+	/* enable RX and TX ready overide */
+	ar933x_uart_rmw_set(up, AR933X_UART_CS_REG,
+		AR933X_UART_CS_TX_READY_ORIDE | AR933X_UART_CS_RX_READY_ORIDE);
+
 	/* Enable RX interrupts */
 	up->ier = AR933X_UART_INT_RX_VALID;
 	ar933x_uart_write(up, AR933X_UART_INT_EN_REG, up->ier);