| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <61ec9870-e6ac-5a92-aaf8-881d19948d96@amlogic.com>
Date: Mon, 10 Feb 2020 14:16:14 +0800
From: Jian Hu <jian.hu@...ogic.com>
To: Jerome Brunet <jbrunet@...libre.com>,
Neil Armstrong <narmstrong@...libre.com>
CC: Kevin Hilman <khilman@...libre.com>, Rob Herring <robh@...nel.org>,
Martin Blumenstingl <martin.blumenstingl@...glemail.com>,
Michael Turquette <mturquette@...libre.com>,
Stephen Boyd <sboyd@...nel.org>,
Qiufang Dai <qiufang.dai@...ogic.com>,
Jianxin Pan <jianxin.pan@...ogic.com>,
Victor Wan <victor.wan@...ogic.com>,
Chandle Zou <chandle.zou@...ogic.com>,
<linux-clk@...r.kernel.org>, <linux-amlogic@...ts.infradead.org>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v7 3/5] clk: meson: a1: add support for Amlogic A1 PLL
clock driver
On 2020/2/4 21:13, Jerome Brunet wrote:
>
> On Mon 20 Jan 2020 at 04:49, Jian Hu <jian.hu@...ogic.com> wrote:
>
>> The Amlogic A1 clock includes three drivers:
>> pll clocks, peripheral clocks, CPU clocks.
>> sys pll and CPU clocks will be sent in next patch.
>>
>> Unlike the previous series, there is no EE/AO domain
>> in A1 CLK controllers.
>>
>> Signed-off-by: Jian Hu <jian.hu@...ogic.com>
>> ---
>> drivers/clk/meson/Kconfig | 9 +
>> drivers/clk/meson/Makefile | 1 +
>> drivers/clk/meson/a1-pll.c | 360 +++++++++++++++++++++++++++++++++++++
>> drivers/clk/meson/a1-pll.h | 56 ++++++
>> 4 files changed, 426 insertions(+)
>> create mode 100644 drivers/clk/meson/a1-pll.c
>> create mode 100644 drivers/clk/meson/a1-pll.h
>>
>> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
>> index dabeb435d067..31613c3bbbc7 100644
>> --- a/drivers/clk/meson/Kconfig
>> +++ b/drivers/clk/meson/Kconfig
>> @@ -93,6 +93,15 @@ config COMMON_CLK_AXG_AUDIO
>> Support for the audio clock controller on AmLogic A113D devices,
>> aka axg, Say Y if you want audio subsystem to work.
>>
>> +config COMMON_CLK_A1_PLL
>> + bool
>> + depends on ARCH_MESON
>> + select COMMON_CLK_MESON_REGMAP
>> + select COMMON_CLK_MESON_PLL
>> + help
>> + Support for the PLL clock controller on Amlogic A113L device,
>> + aka a1. Say Y if you want PLL to work.
>> +
>> config COMMON_CLK_G12A
>> bool
>> depends on ARCH_MESON
>> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
>> index 3939f218587a..71d3b8e6fb8a 100644
>> --- a/drivers/clk/meson/Makefile
>> +++ b/drivers/clk/meson/Makefile
>> @@ -16,6 +16,7 @@ obj-$(CONFIG_COMMON_CLK_MESON_VID_PLL_DIV) += vid-pll-div.o
>>
>> obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o
>> obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
>> +obj-$(CONFIG_COMMON_CLK_A1_PLL) += a1-pll.o
>> obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
>> obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o g12a-aoclk.o
>> obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o
>> diff --git a/drivers/clk/meson/a1-pll.c b/drivers/clk/meson/a1-pll.c
>> new file mode 100644
>> index 000000000000..69c1ca07d041
>> --- /dev/null
>> +++ b/drivers/clk/meson/a1-pll.c
>> @@ -0,0 +1,360 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +/*
>> + * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
>> + * Author: Jian Hu <jian.hu@...ogic.com>
>> + */
>> +
>> +#include <linux/clk-provider.h>
>> +#include <linux/of_device.h>
>> +#include <linux/platform_device.h>
>> +#include "a1-pll.h"
>> +#include "clk-pll.h"
>> +#include "clk-regmap.h"
>> +
>> +static struct clk_regmap a1_fixed_pll_dco = {
>> + .data = &(struct meson_clk_pll_data){
>> + .en = {
>> + .reg_off = ANACTRL_FIXPLL_CTRL0,
>> + .shift = 28,
>> + .width = 1,
>> + },
>> + .m = {
>> + .reg_off = ANACTRL_FIXPLL_CTRL0,
>> + .shift = 0,
>> + .width = 8,
>> + },
>> + .n = {
>> + .reg_off = ANACTRL_FIXPLL_CTRL0,
>> + .shift = 10,
>> + .width = 5,
>> + },
>> + .frac = {
>> + .reg_off = ANACTRL_FIXPLL_CTRL1,
>> + .shift = 0,
>> + .width = 19,
>> + },
>> + .l = {
>> + .reg_off = ANACTRL_FIXPLL_STS,
>> + .shift = 31,
>> + .width = 1,
>> + },
>> + .rst = {
>> + .reg_off = ANACTRL_FIXPLL_CTRL0,
>> + .shift = 29,
>> + .width = 1,
>> + },
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fixed_pll_dco",
>> + .ops = &meson_clk_pll_ro_ops,
>> + .parent_data = &(const struct clk_parent_data) {
>> + .fw_name = "xtal_fixpll",
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_fixed_pll = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = ANACTRL_FIXPLL_CTRL0,
>> + .bit_idx = 20,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "fixed_pll",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fixed_pll_dco.hw
>> + },
>> + .num_parents = 1,
>> + /*
>> + * It is enough that the fdiv leaf has critical flag,
>> + * No critical or unused flag here.
>> + */
>> + },
>> +};
>> +
>> +static const struct pll_mult_range a1_hifi_pll_mult_range = {
>> + .min = 32,
>> + .max = 64,
>> +};
>> +
>> +static const struct reg_sequence a1_hifi_init_regs[] = {
>> + { .reg = ANACTRL_HIFIPLL_CTRL1, .def = 0x01800000 },
>> + { .reg = ANACTRL_HIFIPLL_CTRL2, .def = 0x00001100 },
>> + { .reg = ANACTRL_HIFIPLL_CTRL3, .def = 0x100a1100 },
>> + { .reg = ANACTRL_HIFIPLL_CTRL4, .def = 0x00302000 },
>> + { .reg = ANACTRL_HIFIPLL_CTRL0, .def = 0x01f18440 },
>> +};
>> +
>> +static struct clk_regmap a1_hifi_pll = {
>> + .data = &(struct meson_clk_pll_data){
>> + .en = {
>> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
>> + .shift = 28,
>> + .width = 1,
>> + },
>> + .m = {
>> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
>> + .shift = 0,
>> + .width = 8,
>> + },
>> + .n = {
>> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
>> + .shift = 10,
>> + .width = 5,
>> + },
>> + .frac = {
>> + .reg_off = ANACTRL_HIFIPLL_CTRL1,
>> + .shift = 0,
>> + .width = 19,
>> + },
>> + .l = {
>> + .reg_off = ANACTRL_HIFIPLL_STS,
>> + .shift = 31,
>> + .width = 1,
>> + },
>> + .current_en = {
>> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
>> + .shift = 26,
>> + .width = 1,
>> + },
>> + .l_detect = {
>> + .reg_off = ANACTRL_HIFIPLL_CTRL2,
>> + .shift = 6,
>> + .width = 1,
>> + },
>> + .range = &a1_hifi_pll_mult_range,
>> + .init_regs = a1_hifi_init_regs,
>> + .init_count = ARRAY_SIZE(a1_hifi_init_regs),
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "hifi_pll",
>> + .ops = &meson_clk_pll_ops,
>> + .parent_data = &(const struct clk_parent_data) {
>> + .fw_name = "xtal_hifipll",
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_fixed_factor a1_fclk_div2_div = {
>> + .mult = 1,
>> + .div = 2,
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fclk_div2_div",
>> + .ops = &clk_fixed_factor_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fixed_pll.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_fclk_div2 = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = ANACTRL_FIXPLL_CTRL0,
>> + .bit_idx = 21,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fclk_div2",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fclk_div2_div.hw
>> + },
>> + .num_parents = 1,
>> + /*
>> + * This clock is used by DDR clock in BL2 firmware
>> + * and is required by the platform to operate correctly.
>> + * Until the following condition are met, we need this clock to
>> + * be marked as critical:
>> + * a) Mark the clock used by a firmware resource, if possible
>> + * b) CCF has a clock hand-off mechanism to make the sure the
>> + * clock stays on until the proper driver comes along
>> + */
>> + .flags = CLK_IS_CRITICAL,
>> + },
>> +};
>> +
>> +static struct clk_fixed_factor a1_fclk_div3_div = {
>> + .mult = 1,
>> + .div = 3,
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fclk_div3_div",
>> + .ops = &clk_fixed_factor_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fixed_pll.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_fclk_div3 = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = ANACTRL_FIXPLL_CTRL0,
>> + .bit_idx = 22,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fclk_div3",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fclk_div3_div.hw
>> + },
>> + .num_parents = 1,
>> + /*
>> + * This clock is used by APB bus which is set in boot ROM code
>> + * and is required by the platform to operate correctly.
>> + * About critical, refer to a1_fclk_div2.
>> + */
>> + .flags = CLK_IS_CRITICAL,
>> + },
>> +};
>> +
>> +static struct clk_fixed_factor a1_fclk_div5_div = {
>> + .mult = 1,
>> + .div = 5,
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fclk_div5_div",
>> + .ops = &clk_fixed_factor_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fixed_pll.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_fclk_div5 = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = ANACTRL_FIXPLL_CTRL0,
>> + .bit_idx = 23,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fclk_div5",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fclk_div5_div.hw
>> + },
>> + .num_parents = 1,
>> + /*
>> + * This clock is used by AXI bus which setted in Romcode
>> + * and is required by the platform to operate correctly.
>> + * About critical, refer to a1_fclk_div2.
>> + */
>> + .flags = CLK_IS_CRITICAL,
>> + },
>> +};
>> +
>> +static struct clk_fixed_factor a1_fclk_div7_div = {
>> + .mult = 1,
>> + .div = 7,
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fclk_div7_div",
>> + .ops = &clk_fixed_factor_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fixed_pll.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_fclk_div7 = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = ANACTRL_FIXPLL_CTRL0,
>> + .bit_idx = 24,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fclk_div7",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fclk_div7_div.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +/* Array of all clocks provided by this provider */
>> +static struct clk_hw_onecell_data a1_pll_hw_onecell_data = {
>> + .hws = {
>> + [CLKID_FIXED_PLL_DCO] = &a1_fixed_pll_dco.hw,
>> + [CLKID_FIXED_PLL] = &a1_fixed_pll.hw,
>> + [CLKID_HIFI_PLL] = &a1_hifi_pll.hw,
>> + [CLKID_FCLK_DIV2] = &a1_fclk_div2.hw,
>> + [CLKID_FCLK_DIV3] = &a1_fclk_div3.hw,
>> + [CLKID_FCLK_DIV5] = &a1_fclk_div5.hw,
>> + [CLKID_FCLK_DIV7] = &a1_fclk_div7.hw,
>> + [CLKID_FCLK_DIV2_DIV] = &a1_fclk_div2_div.hw,
>> + [CLKID_FCLK_DIV3_DIV] = &a1_fclk_div3_div.hw,
>> + [CLKID_FCLK_DIV5_DIV] = &a1_fclk_div5_div.hw,
>> + [CLKID_FCLK_DIV7_DIV] = &a1_fclk_div7_div.hw,
>> + [NR_PLL_CLKS] = NULL,
>> + },
>> + .num = NR_PLL_CLKS,
>> +};
>> +
>> +static struct clk_regmap *const a1_pll_regmaps[] = {
>> + &a1_fixed_pll_dco,
>> + &a1_fixed_pll,
>> + &a1_hifi_pll,
>> + &a1_fclk_div2,
>> + &a1_fclk_div3,
>> + &a1_fclk_div5,
>> + &a1_fclk_div7,
>> +};
>> +
>> +static struct regmap_config clkc_regmap_config = {
>> + .reg_bits = 32,
>> + .val_bits = 32,
>> + .reg_stride = 4,
>> +};
>> +
>> +static int meson_a1_pll_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct resource *res;
>> + void __iomem *base;
>> + struct regmap *map;
>> + int ret, i;
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> +
>> + base = devm_ioremap_resource(dev, res);
>> + if (IS_ERR(base))
>> + return PTR_ERR(base);
>> +
>> + map = devm_regmap_init_mmio(dev, base, &clkc_regmap_config);
>> + if (IS_ERR(map))
>> + return PTR_ERR(map);
>> +
>> + /* Populate regmap for the regmap backed clocks */
>> + for (i = 0; i < ARRAY_SIZE(a1_pll_regmaps); i++)
>> + a1_pll_regmaps[i]->map = map;
>> +
>> + for (i = 0; i < a1_pll_hw_onecell_data.num; i++) {
>> + /* array might be sparse */
>> + if (!a1_pll_hw_onecell_data.hws[i])
>> + continue;
>> +
>> + ret = devm_clk_hw_register(dev, a1_pll_hw_onecell_data.hws[i]);
>> + if (ret) {
>> + dev_err(dev, "Clock registration failed\n");
>> + return ret;
>> + }
>> + }
>> +
>> + return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get,
>> + &a1_pll_hw_onecell_data);
>> +}
>> +
>> +static const struct of_device_id clkc_match_table[] = {
>> + { .compatible = "amlogic,a1-pll-clkc", },
>> + {}
>> +};
>> +
>> +static struct platform_driver a1_pll_driver = {
>> + .probe = meson_a1_pll_probe,
>> + .driver = {
>> + .name = "a1-pll-clkc",
>> + .of_match_table = clkc_match_table,
>> + },
>> +};
>> +
>> +builtin_platform_driver(a1_pll_driver);
>> diff --git a/drivers/clk/meson/a1-pll.h b/drivers/clk/meson/a1-pll.h
>> new file mode 100644
>> index 000000000000..8ded267061ad
>> --- /dev/null
>> +++ b/drivers/clk/meson/a1-pll.h
>> @@ -0,0 +1,56 @@
>> +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
>> +/*
>> + * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
>> + */
>> +
>> +#ifndef __A1_PLL_H
>> +#define __A1_PLL_H
>> +
>> +/* PLL register offset */
>> +#define ANACTRL_FIXPLL_CTRL0 0x0
>> +#define ANACTRL_FIXPLL_CTRL1 0x4
>> +#define ANACTRL_FIXPLL_CTRL2 0x8
>> +#define ANACTRL_FIXPLL_CTRL3 0xc
>> +#define ANACTRL_FIXPLL_CTRL4 0x10
>> +#define ANACTRL_FIXPLL_STS 0x14
>> +#define ANACTRL_SYSPLL_CTRL0 0x80
>> +#define ANACTRL_SYSPLL_CTRL1 0x84
>> +#define ANACTRL_SYSPLL_CTRL2 0x88
>> +#define ANACTRL_SYSPLL_CTRL3 0x8c
>> +#define ANACTRL_SYSPLL_CTRL4 0x90
>> +#define ANACTRL_SYSPLL_STS 0x94
>> +#define ANACTRL_HIFIPLL_CTRL0 0xc0
>> +#define ANACTRL_HIFIPLL_CTRL1 0xc4
>> +#define ANACTRL_HIFIPLL_CTRL2 0xc8
>> +#define ANACTRL_HIFIPLL_CTRL3 0xcc
>> +#define ANACTRL_HIFIPLL_CTRL4 0xd0
>> +#define ANACTRL_HIFIPLL_STS 0xd4
>
> Non of the definition below are used.
> What are they ? Do you need them ?
>
They have not been used, It is a PLL used by audio.
I will remove them.
>> +#define ANACTRL_AUDDDS_CTRL0 0x100
>> +#define ANACTRL_AUDDDS_CTRL1 0x104
>> +#define ANACTRL_AUDDDS_CTRL2 0x108
>> +#define ANACTRL_AUDDDS_CTRL3 0x10c
>> +#define ANACTRL_AUDDDS_CTRL4 0x110
>> +#define ANACTRL_AUDDDS_STS 0x114
>> +#define ANACTRL_MISCTOP_CTRL0 0x140
>> +#define ANACTRL_POR_CNTL 0x188
>> +
>> +/*
>> + * CLKID index values
>> + *
>> + * These indices are entirely contrived and do not map onto the hardware.
>> + * It has now been decided to expose everything by default in the DT header:
>> + * include/dt-bindings/clock/a1-pll-clkc.h. Only the clocks ids we don't want
>> + * to expose, such as the internal muxes and dividers of composite clocks,
>> + * will remain defined here.
>> + */
>> +#define CLKID_FIXED_PLL_DCO 0
>> +#define CLKID_FCLK_DIV2_DIV 2
>> +#define CLKID_FCLK_DIV3_DIV 3
>> +#define CLKID_FCLK_DIV5_DIV 4
>> +#define CLKID_FCLK_DIV7_DIV 5
>> +#define NR_PLL_CLKS 11
>> +
>> +/* include the CLKIDs that have been made part of the DT binding */
>> +#include <dt-bindings/clock/a1-pll-clkc.h>
>> +
>> +#endif /* __A1_PLL_H */
>
> .
>
Powered by blists - more mailing lists