linux-kernel - RE: [PATCH 2/2] arm64: defconfig: enable additional drivers needed by NXP QorIQ boards

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <VE1PR04MB668774D60323E11C7FF1FF7F8F110@VE1PR04MB6687.eurprd04.prod.outlook.com>
Date:   Tue, 18 Feb 2020 16:44:09 +0000
From:   Leo Li <leoyang.li@....com>
To:     Shawn Guo <shawnguo@...nel.org>
CC:     "linux-arm-kernel@...ts.infradead.org" 
        <linux-arm-kernel@...ts.infradead.org>,
        "linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>
Subject: RE: [PATCH 2/2] arm64: defconfig: enable additional drivers needed by
 NXP QorIQ boards



> -----Original Message-----
> From: Shawn Guo <shawnguo@...nel.org>
> Sent: Sunday, February 16, 2020 11:38 PM
> To: Leo Li <leoyang.li@....com>
> Cc: linux-arm-kernel@...ts.infradead.org; linux-kernel@...r.kernel.org
> Subject: Re: [PATCH 2/2] arm64: defconfig: enable additional drivers needed
> by NXP QorIQ boards
> 
> On Mon, Feb 10, 2020 at 06:55:59PM -0600, Li Yang wrote:
> > This enables the following SoC device drivers for NXP/FSL QorIQ SoCs:
> > CONFIG_QORIQ_CPUFREQ=y
> > CONFIG_NET_SWITCHDEV=y
> > CONFIG_MSCC_OCELOT_SWITCH=y
> > CONFIG_CAN=m
> > CONFIG_CAN_FLEXCAN=m
> > CONFIG_FSL_MC_BUS=y
> > CONFIG_MTD_NAND_FSL_IFC=y
> > CONFIG_FSL_ENETC=y
> > CONFIG_FSL_ENETC_VF=y
> > CONFIG_SPI_FSL_LPSPI=y
> > CONFIG_SPI_FSL_QUADSPI=y
> > CONFIG_SPI_FSL_DSPI=y
> > CONFIG_GPIO_MPC8XXX=y
> > CONFIG_ARM_SBSA_WATCHDOG=y
> > CONFIG_DRM_MALI_DISPLAY=m
> > CONFIG_FSL_MC_DPIO=y
> > CONFIG_CRYPTO_DEV_FSL_DPAA2_CAAM=m
> > CONFIG_FSL_DPAA=y
> > CONFIG_FSL_FMAN=y
> > CONFIG_FSL_DPAA_ETH=y
> > CONFIG_FSL_DPAA2_ETH=y
> >
> > And the drivers for on-board devices for the upstreamed QorIQ
> > reference
> > boards:
> > CONFIG_MTD_CFI=y
> > CONFIG_MTD_CFI_ADV_OPTIONS=y
> > CONFIG_MTD_CFI_INTELEXT=y
> > CONFIG_MTD_CFI_AMDSTD=y
> > CONFIG_MTD_CFI_STAA=y
> > CONFIG_MTD_PHYSMAP=y
> > CONFIG_MTD_PHYSMAP_OF=y
> > CONFIG_MTD_DATAFLASH=y
> > CONFIG_MTD_SST25L=y
> > CONFIG_EEPROM_AT24=m
> > CONFIG_RTC_DRV_DS1307=y
> > CONFIG_RTC_DRV_PCF85363=y
> > CONFIG_RTC_DRV_PCF2127=y
> > CONFIG_E1000=y
> > CONFIG_AQUANTIA_PHY=y
> > CONFIG_MICROSEMI_PHY=y
> > CONFIG_VITESSE_PHY=y
> > CONFIG_MDIO_BUS_MUX_MULTIPLEXER=y
> > CONFIG_MUX_MMIO=y
> >
> > The following two options are implied by new options and removed from
> > defconfig:
> > CONFIG_CLK_QORIQ=y
> > CONFIG_MEMORY=y
> >
> > Signed-off-by: Li Yang <leoyang.li@....com>
> 
> This is too much change in a single patch. It should be split properly to make
> review and merge easier, considering arm-soc folks are cautious to those 'y'
> options.

Ok.  So probably separating them based on different subsystems will be good?  It would be too many patches if I separate for each individual config option.

Regards,
Leo