| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20200219151617.GA22892@bogus>
Date: Wed, 19 Feb 2020 09:16:17 -0600
From: Rob Herring <robh@...nel.org>
To: Benjamin Gaignard <benjamin.gaignard@...com>
Cc: lee.jones@...aro.org, mark.rutland@....co, alexandre.torgue@...com,
linus.walleij@...aro.org, amelie.delaunay@...com,
devicetree@...r.kernel.org,
linux-stm32@...md-mailman.stormreply.com,
linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
linux-gpio@...r.kernel.org
Subject: Re: [PATCH v2] dt-bindings: mfd: Convert stmfx bindings to
json-schema
On Fri, Feb 07, 2020 at 03:57:12PM +0100, Benjamin Gaignard wrote:
> Convert stmfx bindings to json-schema
>
> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@...com>
> ---
> version 2:
> - fix description indentation
> - change pin controller node name to pinctrl
> - document pinctrl subnode properties
> - add pinctrl subnode example
>
> Documentation/devicetree/bindings/mfd/stmfx.txt | 28 -----
> Documentation/devicetree/bindings/mfd/stmfx.yaml | 120 +++++++++++++++++++++
> .../devicetree/bindings/pinctrl/pinctrl-stmfx.txt | 116 --------------------
> 3 files changed, 120 insertions(+), 144 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/mfd/stmfx.txt
> create mode 100644 Documentation/devicetree/bindings/mfd/stmfx.yaml
> delete mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-stmfx.txt
>
> diff --git a/Documentation/devicetree/bindings/mfd/stmfx.txt b/Documentation/devicetree/bindings/mfd/stmfx.txt
> deleted file mode 100644
> index f0c2f7fcf5c7..000000000000
> --- a/Documentation/devicetree/bindings/mfd/stmfx.txt
> +++ /dev/null
> @@ -1,28 +0,0 @@
> -STMicroelectonics Multi-Function eXpander (STMFX) Core bindings
> -
> -ST Multi-Function eXpander (STMFX) is a slave controller using I2C for
> -communication with the main MCU. Its main features are GPIO expansion, main
> -MCU IDD measurement (IDD is the amount of current that flows through VDD) and
> -resistive touchscreen controller.
> -
> -Required properties:
> -- compatible: should be "st,stmfx-0300".
> -- reg: I2C slave address of the device.
> -- interrupts: interrupt specifier triggered by MFX_IRQ_OUT signal.
> - Please refer to ../interrupt-controller/interrupt.txt
> -
> -Optional properties:
> -- drive-open-drain: configure MFX_IRQ_OUT as open drain.
> -- vdd-supply: phandle of the regulator supplying STMFX.
> -
> -Example:
> -
> - stmfx: stmfx@42 {
> - compatible = "st,stmfx-0300";
> - reg = <0x42>;
> - interrupts = <8 IRQ_TYPE_EDGE_RISING>;
> - interrupt-parent = <&gpioi>;
> - vdd-supply = <&v3v3>;
> - };
> -
> -Please refer to ../pinctrl/pinctrl-stmfx.txt for STMFX GPIO expander function bindings.
> diff --git a/Documentation/devicetree/bindings/mfd/stmfx.yaml b/Documentation/devicetree/bindings/mfd/stmfx.yaml
> new file mode 100644
> index 000000000000..1af906fb876f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/stmfx.yaml
> @@ -0,0 +1,120 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/mfd/stmfx.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: STMicroelectonics Multi-Function eXpander (STMFX) bindings
> +
> +description: ST Multi-Function eXpander (STMFX) is a slave controller using I2C for
> + communication with the main MCU. Its main features are GPIO expansion,
> + main MCU IDD measurement (IDD is the amount of current that flows
> + through VDD) and resistive touchscreen controller.
> +
> +maintainers:
> + - Amelie Delaunay <amelie.delaunay@...com>
> +
> +properties:
> + compatible:
> + const: st,stmfx-0300
> +
> + reg:
> + enum: [ 0x42, 0x43 ]
> +
> + interrupts:
> + maxItems: 1
> +
> + drive-open-drain: true
> +
> + vdd-supply:
> + maxItems: 1
> +
> + pinctrl:
> + type: object
> +
> + $ref: ../pinctrl/pincfg-node.yaml
allOf needed here.
However, this is not in the right spot.
> +
> + properties:
> + compatible:
> + const: st,stmfx-0300-pinctrl
> +
> + "#gpio-cells":
> + const: 2
> +
> + "#interrupt-cells":
> + const: 2
> +
> + gpio-controller: true
> +
> + interrupt-controller: true
> +
> + gpio-ranges:
> + description: if all STMFX pins[24:0] are available (no other STMFX function in use),
> + you should use gpio-ranges = <&stmfx_pinctrl 0 0 24>;
> + if agpio[3:0] are not available (STMFX Touchscreen function in use),
> + you should use gpio-ranges = <&stmfx_pinctrl 0 0 16>, <&stmfx_pinctrl 20 20 4>;
> + if agpio[7:4] are not available (STMFX IDD function in use),
> + you should use gpio-ranges = <&stmfx_pinctrl 0 0 20>;
> + maxItems: 1
> +
> + patternProperties:
> + "^[a-zA-Z][a-zA-Z0-9_]+$":
I'm surprised this works because it is going to match on most of the
other properties in this node. You really need a node name pattern you
can match on like '-pins$'. Otherwise, you have to do:
if:
type: object
then:
...
I'd rather see the dts files fixed.
> + type: object
> + $ref: ../pinctrl/pinmux-node.yaml
Actually, this is why it doesn't error. With no 'allOf', 'type: object'
is ignored.
> +
> + properties:
> + pins: true
> + bias-disable: true
> + bias-pull-up: true
> + bias-pull-pin-default: true
> + bias-pull-down: true
> + drive-open-drain: true
> + drive-push-pull: true
> + output-high: true
> + output-low: true
'additionalProperties: false' needed here.
> +
> + required:
> + - compatible
> + - "#gpio-cells"
> + - "#interrupt-cells"
> + - gpio-controller
> + - interrupt-controller
> + - gpio-ranges
> +
> +additionalProperties: false
> +
> +required:
> + - compatible
> + - reg
> + - interrupts
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + stmfx@42 {
> + compatible = "st,stmfx-0300";
> + reg = <0x42>;
> + interrupts = <8 IRQ_TYPE_EDGE_RISING>;
> + interrupt-parent = <&gpioi>;
> + vdd-supply = <&v3v3>;
> +
> + stmfx_pinctrl: pinctrl {
> + compatible = "st,stmfx-0300-pinctrl";
> + #gpio-cells = <2>;
> + #interrupt-cells = <2>;
> + gpio-controller;
> + interrupt-controller;
> + gpio-ranges = <&stmfx_pinctrl 0 0 24>;
> +
> + joystick_pins: joystick {
> + pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4";
> + drive-push-pull;
> + bias-pull-up;
> + };
> + };
> + };
> + };
> +...
> diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-stmfx.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-stmfx.txt
> deleted file mode 100644
> index c1b4c1819b84..000000000000
> --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-stmfx.txt
> +++ /dev/null
> @@ -1,116 +0,0 @@
> -STMicroelectronics Multi-Function eXpander (STMFX) GPIO expander bindings
> -
> -ST Multi-Function eXpander (STMFX) offers up to 24 GPIOs expansion.
> -Please refer to ../mfd/stmfx.txt for STMFX Core bindings.
> -
> -Required properties:
> -- compatible: should be "st,stmfx-0300-pinctrl".
> -- #gpio-cells: should be <2>, the first cell is the GPIO number and the second
> - cell is the gpio flags in accordance with <dt-bindings/gpio/gpio.h>.
> -- gpio-controller: marks the device as a GPIO controller.
> -- #interrupt-cells: should be <2>, the first cell is the GPIO number and the
> - second cell is the interrupt flags in accordance with
> - <dt-bindings/interrupt-controller/irq.h>.
> -- interrupt-controller: marks the device as an interrupt controller.
> -- gpio-ranges: specifies the mapping between gpio controller and pin
> - controller pins. Check "Concerning gpio-ranges property" below.
> -Please refer to ../gpio/gpio.txt.
> -
> -Please refer to pinctrl-bindings.txt for pin configuration.
> -
> -Required properties for pin configuration sub-nodes:
> -- pins: list of pins to which the configuration applies.
> -
> -Optional properties for pin configuration sub-nodes (pinconf-generic ones):
> -- bias-disable: disable any bias on the pin.
> -- bias-pull-up: the pin will be pulled up.
> -- bias-pull-pin-default: use the pin-default pull state.
> -- bias-pull-down: the pin will be pulled down.
> -- drive-open-drain: the pin will be driven with open drain.
> -- drive-push-pull: the pin will be driven actively high and low.
> -- output-high: the pin will be configured as an output driving high level.
> -- output-low: the pin will be configured as an output driving low level.
> -
> -Note that STMFX pins[15:0] are called "gpio[15:0]", and STMFX pins[23:16] are
> -called "agpio[7:0]". Example, to refer to pin 18 of STMFX, use "agpio2".
> -
> -Concerning gpio-ranges property:
> -- if all STMFX pins[24:0] are available (no other STMFX function in use), you
> - should use gpio-ranges = <&stmfx_pinctrl 0 0 24>;
> -- if agpio[3:0] are not available (STMFX Touchscreen function in use), you
> - should use gpio-ranges = <&stmfx_pinctrl 0 0 16>, <&stmfx_pinctrl 20 20 4>;
> -- if agpio[7:4] are not available (STMFX IDD function in use), you
> - should use gpio-ranges = <&stmfx_pinctrl 0 0 20>;
> -
> -
> -Example:
> -
> - stmfx: stmfx@42 {
> - ...
> -
> - stmfx_pinctrl: stmfx-pin-controller {
> - compatible = "st,stmfx-0300-pinctrl";
> - #gpio-cells = <2>;
> - #interrupt-cells = <2>;
> - gpio-controller;
> - interrupt-controller;
> - gpio-ranges = <&stmfx_pinctrl 0 0 24>;
> -
> - joystick_pins: joystick {
> - pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4";
> - drive-push-pull;
> - bias-pull-up;
> - };
> - };
> - };
> -
> -Example of STMFX GPIO consumers:
> -
> - joystick {
> - compatible = "gpio-keys";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - pinctrl-0 = <&joystick_pins>;
> - pinctrl-names = "default";
> - button-0 {
> - label = "JoySel";
> - linux,code = <KEY_ENTER>;
> - interrupt-parent = <&stmfx_pinctrl>;
> - interrupts = <0 IRQ_TYPE_EDGE_RISING>;
> - };
> - button-1 {
> - label = "JoyDown";
> - linux,code = <KEY_DOWN>;
> - interrupt-parent = <&stmfx_pinctrl>;
> - interrupts = <1 IRQ_TYPE_EDGE_RISING>;
> - };
> - button-2 {
> - label = "JoyLeft";
> - linux,code = <KEY_LEFT>;
> - interrupt-parent = <&stmfx_pinctrl>;
> - interrupts = <2 IRQ_TYPE_EDGE_RISING>;
> - };
> - button-3 {
> - label = "JoyRight";
> - linux,code = <KEY_RIGHT>;
> - interrupt-parent = <&stmfx_pinctrl>;
> - interrupts = <3 IRQ_TYPE_EDGE_RISING>;
> - };
> - button-4 {
> - label = "JoyUp";
> - linux,code = <KEY_UP>;
> - interrupt-parent = <&stmfx_pinctrl>;
> - interrupts = <4 IRQ_TYPE_EDGE_RISING>;
> - };
> - };
> -
> - leds {
> - compatible = "gpio-leds";
> - orange {
> - gpios = <&stmfx_pinctrl 17 1>;
> - };
> -
> - blue {
> - gpios = <&stmfx_pinctrl 19 1>;
> - };
> - }
> --
> 2.15.0
>
Powered by blists - more mailing lists