Message-ID: <DB6PR0501MB27121431EA6DCCB476B73F1DDAED0@DB6PR0501MB2712.eurprd05.prod.outlook.com>
Date:   Tue, 25 Feb 2020 16:42:32 +0000
From:   Asmaa Mnebhi <Asmaa@...lanox.com>
To:     "bgolaszewski@...libre.com" <bgolaszewski@...libre.com>,
        "linus.walleij@...aro.org" <linus.walleij@...aro.org>
CC:     "linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>
Subject: RE: [PATCH v2 1/1] gpio: add driver for Mellanox BlueField 2 GPIO
 controller

Hi Linus,

Thank you for your feedback! 
I have addressed your comments and tested the code. Please note that the YU_ARM_GPIO_LOCK is a shared resource between the 3 gpio blocks instances.
So now that we have split up the gpio_chip into 3 instances, we need to share that LOCK resource accordingly. I have created a global variable for that purpose.
Also note, that although it is not supported in this driver at the moment, some gpio interrupt registers will be similar to that LOCK i.e. they are shared among the  3 gpio block instances.

-----Original Message-----
From: Asmaa Mnebhi <Asmaa@...lanox.com> 
Sent: Tuesday, February 25, 2020 11:33 AM
To: bgolaszewski@...libre.com; linus.walleij@...aro.org
Cc: Asmaa Mnebhi <Asmaa@...lanox.com>; linux-kernel@...r.kernel.org
Subject: [PATCH v2 1/1] gpio: add driver for Mellanox BlueField 2 GPIO controller

This patch adds support for the GPIO controller used by Mellanox BlueField 2 SOCs.

Signed-off-by: Asmaa Mnebhi <Asmaa@...lanox.com>
---
 drivers/gpio/Kconfig       |   7 +
 drivers/gpio/Makefile      |   1 +
 drivers/gpio/gpio-mlxbf2.c | 345 +++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 353 insertions(+)
 create mode 100644 drivers/gpio/gpio-mlxbf2.c

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index b8013cf..6234ccc 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -1399,6 +1399,13 @@ config GPIO_MLXBF
 	help
 	  Say Y here if you want GPIO support on Mellanox BlueField SoC.
 
+config GPIO_MLXBF2
+	tristate "Mellanox BlueField 2 SoC GPIO"
+	depends on (MELLANOX_PLATFORM && ARM64 && ACPI) || (64BIT && COMPILE_TEST)
+	select GPIO_GENERIC
+	help
+	  Say Y here if you want GPIO support on Mellanox BlueField 2 SoC.
+
 config GPIO_ML_IOH
 	tristate "OKI SEMICONDUCTOR ML7213 IOH GPIO support"
 	depends on X86 || COMPILE_TEST
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index 0b57126..b2cfc21 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -93,6 +93,7 @@ obj-$(CONFIG_GPIO_MENZ127)		+= gpio-menz127.o
 obj-$(CONFIG_GPIO_MERRIFIELD)		+= gpio-merrifield.o
 obj-$(CONFIG_GPIO_ML_IOH)		+= gpio-ml-ioh.o
 obj-$(CONFIG_GPIO_MLXBF)		+= gpio-mlxbf.o
+obj-$(CONFIG_GPIO_MLXBF2)		+= gpio-mlxbf2.o
 obj-$(CONFIG_GPIO_MM_LANTIQ)		+= gpio-mm-lantiq.o
 obj-$(CONFIG_GPIO_MOCKUP)		+= gpio-mockup.o
 obj-$(CONFIG_GPIO_MOXTET)		+= gpio-moxtet.o
diff --git a/drivers/gpio/gpio-mlxbf2.c b/drivers/gpio/gpio-mlxbf2.c new file mode 100644 index 0000000..0d35d4e
--- /dev/null
+++ b/drivers/gpio/gpio-mlxbf2.c
@@ -0,0 +1,345 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <linux/acpi.h>
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+#include <linux/device.h>
+#include <linux/gpio/driver.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/resource.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+#include <linux/version.h>
+
+/*
+ * There are 3 YU GPIO blocks:
+ * gpio[0]: HOST_GPIO0->HOST_GPIO31
+ * gpio[1]: HOST_GPIO32->HOST_GPIO63
+ * gpio[2]: HOST_GPIO64->HOST_GPIO69
+ */
+#define MLXBF2_GPIO_MAX_PINS_PER_BLOCK 32
+
+/*
+ * arm_gpio_lock register:
+ * bit[31]	lock status: active if set
+ * bit[15:0]	set lock
+ * The lock is enabled only if 0xd42f is written to this field  */
+#define YU_ARM_GPIO_LOCK_ADDR		0x2801088
+#define YU_ARM_GPIO_LOCK_SIZE		0x8
+#define YU_LOCK_ACTIVE_BIT(val)		(val >> 31)
+#define YU_ARM_GPIO_LOCK_ACQUIRE	0xd42f
+#define YU_ARM_GPIO_LOCK_RELEASE	0x0
+
+/*
+ * gpio[x] block registers and their offset  */
+#define YU_GPIO_DATAIN			0x04
+#define YU_GPIO_MODE1			0x08
+#define YU_GPIO_MODE0			0x0c
+#define YU_GPIO_DATASET			0x14
+#define YU_GPIO_DATACLEAR		0x18
+#define YU_GPIO_MODE1_CLEAR		0x50
+#define YU_GPIO_MODE0_SET		0x54
+#define YU_GPIO_MODE0_CLEAR		0x58
+
+#ifdef CONFIG_PM
+struct mlxbf2_gpio_context_save_regs {
+	u32 gpio_mode0;
+	u32 gpio_mode1;
+};
+#endif
+
+/* BlueField-2 gpio block state structure. */ struct mlxbf2_gpio_state 
+{
+	struct gpio_chip gc;
+
+	/* YU GPIO blocks address */
+	void __iomem *gpio_io;
+
+#ifdef CONFIG_PM
+	struct mlxbf2_gpio_context_save_regs *csave_regs; #endif };
+
+/* BlueField-2 gpio shared structure. */ struct mlxbf2_gpio_param {
+	void __iomem *io;
+	struct resource *res;
+	struct mutex *lock;
+};
+
+static struct resource yu_arm_gpio_lock_res = {
+	.start = YU_ARM_GPIO_LOCK_ADDR,
+	.end   = YU_ARM_GPIO_LOCK_ADDR + YU_ARM_GPIO_LOCK_SIZE - 1,
+	.name  = "YU_ARM_GPIO_LOCK",
+};
+
+static DEFINE_MUTEX(yu_arm_gpio_lock_mutex);
+
+static struct mlxbf2_gpio_param yu_arm_gpio_lock_param = {
+	.res = &yu_arm_gpio_lock_res,
+	.lock = &yu_arm_gpio_lock_mutex,
+};
+
+/* Request memory region and map yu_arm_gpio_lock resource */ static 
+int mlxbf2_gpio_get_lock_res(struct platform_device *pdev) {
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	resource_size_t size;
+	int ret = 0;
+
+	mutex_lock(yu_arm_gpio_lock_param.lock);
+
+	/* Check if the memory map already exists */
+	if (yu_arm_gpio_lock_param.io)
+		goto exit;
+
+	res = yu_arm_gpio_lock_param.res;
+	size = resource_size(res);
+
+	if (!devm_request_mem_region(dev, res->start, size, res->name)) {
+		ret = -EFAULT;
+		goto exit;
+	}
+
+	yu_arm_gpio_lock_param.io = devm_ioremap_nocache(dev, res->start, size);
+	if (IS_ERR(yu_arm_gpio_lock_param.io))
+		ret = PTR_ERR(yu_arm_gpio_lock_param.io);
+
+exit:
+	mutex_unlock(yu_arm_gpio_lock_param.lock);
+
+	return ret;
+}
+
+/*
+ * Acquire the YU arm_gpio_lock to be able to change the direction
+ * mode. If the lock_active bit is already set, return an error.
+ */
+static int mlxbf2_gpio_lock_acquire(void) {
+	u32 arm_gpio_lock_val;
+
+	mutex_lock(yu_arm_gpio_lock_param.lock);
+
+	arm_gpio_lock_val = readl(yu_arm_gpio_lock_param.io);
+
+	/*
+	 * When lock active bit[31] is set, ModeX is write enabled
+	 */
+	if (YU_LOCK_ACTIVE_BIT(arm_gpio_lock_val)) {
+		mutex_unlock(yu_arm_gpio_lock_param.lock);
+		return -EINVAL;
+	}
+
+	writel(YU_ARM_GPIO_LOCK_ACQUIRE, yu_arm_gpio_lock_param.io);
+
+	mutex_unlock(yu_arm_gpio_lock_param.lock);
+
+	return 0;
+}
+
+/*
+ * Release the YU arm_gpio_lock after changing the direction mode.
+ */
+static void mlxbf2_gpio_lock_release(void) {
+	mutex_lock(yu_arm_gpio_lock_param.lock);
+	writel(YU_ARM_GPIO_LOCK_RELEASE, yu_arm_gpio_lock_param.io);
+	mutex_unlock(yu_arm_gpio_lock_param.lock);
+}
+
+/*
+ * mode0 and mode1 are both locked by the gpio_lock field.
+ *
+ * Together, mode0 and mode1 define the gpio Mode dependeing also
+ * on Reg_DataOut.
+ *
+ * {mode1,mode0}:{Reg_DataOut=0,Reg_DataOut=1}->{DataOut=0,DataOut=1}
+ *
+ * {0,0}:Reg_DataOut{0,1}->{Z,Z} Input PAD
+ * {0,1}:Reg_DataOut{0,1}->{0,1} Full drive Output PAD
+ * {1,0}:Reg_DataOut{0,1}->{0,Z} 0-set PAD to low, 1-float
+ * {1,1}:Reg_DataOut{0,1}->{Z,1} 0-float, 1-set PAD to high  */
+
+/*
+ * Set input direction:
+ * {mode1,mode0} = {0,0}
+ */
+static int mlxbf2_gpio_direction_input(struct gpio_chip *chip,
+				       unsigned int offset)
+{
+	struct mlxbf2_gpio_state *gs = gpiochip_get_data(chip);
+	int ret;
+
+	/*
+	 * Although the arm_gpio_lock was set in the probe function, check again
+	 * if it is still enabled to be able to write to the ModeX registers.
+	 */
+	spin_lock(&gs->gc.bgpio_lock);
+	ret = mlxbf2_gpio_lock_acquire();
+	if (ret < 0) {
+		spin_unlock(&gs->gc.bgpio_lock);
+		return ret;
+	}
+
+	writel(BIT(offset), gs->gpio_io + YU_GPIO_MODE0_CLEAR);
+	writel(BIT(offset), gs->gpio_io + YU_GPIO_MODE1_CLEAR);
+
+	mlxbf2_gpio_lock_release();
+	spin_unlock(&gs->gc.bgpio_lock);
+
+	return ret;
+}
+
+/*
+ * Set output direction:
+ * {mode1,mode0} = {0,1}
+ */
+static int mlxbf2_gpio_direction_output(struct gpio_chip *chip,
+					unsigned int offset,
+					int value)
+{
+	struct mlxbf2_gpio_state *gs = gpiochip_get_data(chip);
+	int ret = 0;
+
+	/*
+	 * Although the arm_gpio_lock was set in the probe function,
+	 * check again it is still enabled to be able to write to the
+	 * ModeX registers.
+	 */
+	spin_lock(&gs->gc.bgpio_lock);
+	ret = mlxbf2_gpio_lock_acquire();
+	if (ret < 0) {
+		spin_unlock(&gs->gc.bgpio_lock);
+		return ret;
+	}
+
+	writel(BIT(offset), gs->gpio_io + YU_GPIO_MODE1_CLEAR);
+	writel(BIT(offset), gs->gpio_io + YU_GPIO_MODE0_SET);
+
+	mlxbf2_gpio_lock_release();
+	spin_unlock(&gs->gc.bgpio_lock);
+
+	return ret;
+}
+
+/* BlueField-2 GPIO driver initialization routine. */ static int 
+mlxbf2_gpio_probe(struct platform_device *pdev) {
+	struct mlxbf2_gpio_state *gs;
+	struct device *dev = &pdev->dev;
+	struct gpio_chip *gc;
+	struct resource *res;
+	unsigned int npins;
+	int ret;
+
+	gs = devm_kzalloc(dev, sizeof(*gs), GFP_KERNEL);
+	if (!gs)
+		return -ENOMEM;
+
+	/* YU GPIO block address */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -ENODEV;
+
+	gs->gpio_io = devm_ioremap(dev, res->start, resource_size(res));
+	if (!gs->gpio_io)
+		return -ENOMEM;
+
+	ret = mlxbf2_gpio_get_lock_res(pdev);
+	if (ret) {
+		dev_err(dev, "Failed to get yu_arm_gpio_lock resource\n");
+		return ret;
+	}
+
+	if (device_property_read_u32(dev, "npins", &npins))
+		npins = MLXBF2_GPIO_MAX_PINS_PER_BLOCK;
+
+	gc = &gs->gc;
+
+	ret = bgpio_init(gc, dev, 4,
+			gs->gpio_io + YU_GPIO_DATAIN,
+			gs->gpio_io + YU_GPIO_DATASET,
+			gs->gpio_io + YU_GPIO_DATACLEAR,
+			NULL,
+			NULL,
+			0);
+
+	gc->direction_input = mlxbf2_gpio_direction_input;
+	gc->direction_output = mlxbf2_gpio_direction_output;
+	gc->ngpio = npins;
+	gc->owner = THIS_MODULE;
+
+	platform_set_drvdata(pdev, gs);
+
+	ret = devm_gpiochip_add_data(dev, &gs->gc, gs);
+	if (ret) {
+		dev_err(dev, "Failed adding memory mapped gpiochip\n");
+		return ret;
+	}
+
+	dev_info(dev, "Registered Mellanox BlueField-2 GPIO");
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int mlxbf2_gpio_suspend(struct platform_device *pdev,
+				pm_message_t state)
+{
+	struct mlxbf2_gpio_state *gs = platform_get_drvdata(pdev);
+
+	gs->csave_regs->gpio_mode0 = readl(gs->gpio_io +
+		YU_GPIO_MODE0);
+	gs->csave_regs->gpio_mode1 = readl(gs->gpio_io +
+		YU_GPIO_MODE1);
+
+	return 0;
+}
+
+static int mlxbf2_gpio_resume(struct platform_device *pdev) {
+	struct mlxbf2_gpio_state *gs = platform_get_drvdata(pdev);
+
+	writel(gs->csave_regs->gpio_mode0, gs->gpio_io +
+		YU_GPIO_MODE0);
+	writel(gs->csave_regs->gpio_mode1, gs->gpio_io +
+		YU_GPIO_MODE1);
+
+	return 0;
+}
+#endif
+
+static const struct acpi_device_id mlxbf2_gpio_acpi_match[] = {
+	{ "MLNXBF22", 0 },
+	{},
+};
+MODULE_DEVICE_TABLE(acpi, mlxbf2_gpio_acpi_match);
+
+static struct platform_driver mlxbf2_gpio_driver = {
+	.driver = {
+		.name = "mlxbf2_gpio",
+		.acpi_match_table = ACPI_PTR(mlxbf2_gpio_acpi_match),
+	},
+	.probe    = mlxbf2_gpio_probe,
+#ifdef CONFIG_PM
+	.suspend  = mlxbf2_gpio_suspend,
+	.resume   = mlxbf2_gpio_resume,
+#endif
+};
+
+module_platform_driver(mlxbf2_gpio_driver);
+
+MODULE_DESCRIPTION("Mellanox BlueField-2 GPIO Driver"); 
+MODULE_AUTHOR("Mellanox Technologies"); MODULE_LICENSE("GPL v2");
--
2.1.2

Powered by blists - more mailing lists