linux-kernel - [PATCH v2 1/3] media: i2c: imx219: Fix power sequence

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <20200306103246.22213-2-prabhakar.mahadev-lad.rj@bp.renesas.com>
Date:   Fri,  6 Mar 2020 10:32:44 +0000
From:   Lad Prabhakar <prabhakar.csengg@...il.com>
To:     Dave Stevenson <dave.stevenson@...pberrypi.com>,
        Mauro Carvalho Chehab <mchehab@...nel.org>,
        Sakari Ailus <sakari.ailus@...ux.intel.com>
Cc:     linux-media@...r.kernel.org, linux-kernel@...r.kernel.org,
        Lad Prabhakar <prabhakar.mahadev-lad.rj@...renesas.com>
Subject: [PATCH v2 1/3] media: i2c: imx219: Fix power sequence

When supporting Rpi Camera v2 Module on the RZ/G2E, found the driver had
some issues with rcar mipi-csi driver. The sensor never entered into LP-11
state.

The powerup sequence in the datasheet[1] shows the sensor entering into
LP-11 in streaming mode, so to fix this issue transitions are performed
from "streaming -> standby" in the probe() after power up.

With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.

[1] https://publiclab.org/system/images/photos/000/023/294/original/
RASPBERRY_PI_CAMERA_V2_DATASHEET_IMX219PQH5_7.0.0_Datasheet_XXX.PDF

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@...renesas.com>
---
 drivers/media/i2c/imx219.c | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/drivers/media/i2c/imx219.c b/drivers/media/i2c/imx219.c
index f1effb5a5f66..16010ca1781a 100644
--- a/drivers/media/i2c/imx219.c
+++ b/drivers/media/i2c/imx219.c
@@ -1224,6 +1224,23 @@ static int imx219_probe(struct i2c_client *client)
 	/* Set default mode to max resolution */
 	imx219->mode = &supported_modes[0];
 
+	/* sensor doesn't enter LP-11 state upon power up until and unless
+	 * streaming is started, so upon power up switch the modes to:
+	 * streaming -> standby
+	 */
+	ret = imx219_write_reg(imx219, IMX219_REG_MODE_SELECT,
+			       IMX219_REG_VALUE_08BIT, IMX219_MODE_STREAMING);
+	if (ret < 0)
+		goto error_power_off;
+	usleep_range(100, 110);
+
+	/* put sensor back to standby mode */
+	ret = imx219_write_reg(imx219, IMX219_REG_MODE_SELECT,
+			       IMX219_REG_VALUE_08BIT, IMX219_MODE_STANDBY);
+	if (ret < 0)
+		goto error_power_off;
+	usleep_range(100, 110);
+
 	ret = imx219_init_controls(imx219);
 	if (ret)
 		goto error_power_off;
-- 
2.20.1