| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1584461691-14344-1-git-send-email-martin.fuzzey@flowbird.group>
Date: Tue, 17 Mar 2020 17:14:26 +0100
From: Martin Fuzzey <martin.fuzzey@...wbird.group>
To: support.opensource@...semi.com
Cc: Liam Girdwood <lgirdwood@...il.com>,
Mark Brown <broonie@...nel.org>, linux-kernel@...r.kernel.org
Subject: [PATCH] regulator: da9063: fix suspend
The .set_suspend_enable() and .set_suspend_disable() methods are not
supposed to immediately change the regulator state but just indicated
if the regulator should be enabled or disabled when standby mode is
entered (by a hardware signal).
However currently they set control the SEL bits in the DVC registers,
which causes the voltage to change to immediately between the "A"
(normal) and "B" (standby) values as programmed and does nothing for
the enable state...
This means that "regulator-on-in-suspend" does not work (the regulator
is switched off when the PMIC enters standby mode on the hardware
signal) and, potentially, depending on the A and B voltage
configurations the voltage could be incorrectly changed *before*
actually entering suspend.
The right bit to use for the functionality is the "CONF" bit in the
"CONT" register.
The detailed register description says "Sequencer target state"
for this bit which is not very clear but the functional description
is clearer.
>From 5.1.5 System Enable:
De-asserting SYS_EN (changing from active to passive state)
clears control SYSTEM_EN which triggers a power down sequence
into hibernate/standby mode
...
With the exception of supplies that have the xxxx_CONF control
bit asserted, all regulators in power domains POWER1, POWER, and
SYSTEM are sequentially disabled in reverse order.
Regulators with the <x>_CONF bit set remain on but change the
active voltage controlregisters from V<x>_A to V<x>_B
(if V<x>_B is notalready selected).
Signed-off-by: Martin Fuzzey <martin.fuzzey@...wbird.group>
---
drivers/regulator/da9063-regulator.c | 20 ++------------------
1 file changed, 2 insertions(+), 18 deletions(-)
diff --git a/drivers/regulator/da9063-regulator.c b/drivers/regulator/da9063-regulator.c
index 2aceb3b..46b7301 100644
--- a/drivers/regulator/da9063-regulator.c
+++ b/drivers/regulator/da9063-regulator.c
@@ -100,6 +100,7 @@ struct da9063_regulator_info {
.desc.vsel_mask = DA9063_V##regl_name##_MASK, \
.desc.linear_min_sel = DA9063_V##regl_name##_BIAS, \
.sleep = BFIELD(DA9063_REG_V##regl_name##_A, DA9063_LDO_SL), \
+ .suspend = BFIELD(DA9063_REG_##regl_name##_CONT, DA9063_LDO_CONF), \
.suspend_sleep = BFIELD(DA9063_REG_V##regl_name##_B, DA9063_LDO_SL), \
.suspend_vsel_reg = DA9063_REG_V##regl_name##_B
@@ -124,6 +125,7 @@ struct da9063_regulator_info {
.desc.vsel_mask = DA9063_VBUCK_MASK, \
.desc.linear_min_sel = DA9063_VBUCK_BIAS, \
.sleep = BFIELD(DA9063_REG_V##regl_name##_A, DA9063_BUCK_SL), \
+ .suspend = BFIELD(DA9063_REG_##regl_name##_CONT, DA9063_BUCK_CONF), \
.suspend_sleep = BFIELD(DA9063_REG_V##regl_name##_B, DA9063_BUCK_SL), \
.suspend_vsel_reg = DA9063_REG_V##regl_name##_B, \
.mode = BFIELD(DA9063_REG_##regl_name##_CFG, DA9063_BUCK_MODE_MASK)
@@ -465,42 +467,36 @@ static int da9063_ldo_set_suspend_mode(struct regulator_dev *rdev, unsigned mode
da9063_buck_a_limits,
DA9063_REG_BUCK_ILIM_C, DA9063_BCORE1_ILIM_MASK),
DA9063_BUCK_COMMON_FIELDS(BCORE1),
- .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBCORE1_SEL),
},
{
DA9063_BUCK(DA9063, BCORE2, 300, 10, 1570,
da9063_buck_a_limits,
DA9063_REG_BUCK_ILIM_C, DA9063_BCORE2_ILIM_MASK),
DA9063_BUCK_COMMON_FIELDS(BCORE2),
- .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBCORE2_SEL),
},
{
DA9063_BUCK(DA9063, BPRO, 530, 10, 1800,
da9063_buck_a_limits,
DA9063_REG_BUCK_ILIM_B, DA9063_BPRO_ILIM_MASK),
DA9063_BUCK_COMMON_FIELDS(BPRO),
- .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBPRO_SEL),
},
{
DA9063_BUCK(DA9063, BMEM, 800, 20, 3340,
da9063_buck_b_limits,
DA9063_REG_BUCK_ILIM_A, DA9063_BMEM_ILIM_MASK),
DA9063_BUCK_COMMON_FIELDS(BMEM),
- .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBMEM_SEL),
},
{
DA9063_BUCK(DA9063, BIO, 800, 20, 3340,
da9063_buck_b_limits,
DA9063_REG_BUCK_ILIM_A, DA9063_BIO_ILIM_MASK),
DA9063_BUCK_COMMON_FIELDS(BIO),
- .suspend = BFIELD(DA9063_REG_DVC_2, DA9063_VBIO_SEL),
},
{
DA9063_BUCK(DA9063, BPERI, 800, 20, 3340,
da9063_buck_b_limits,
DA9063_REG_BUCK_ILIM_B, DA9063_BPERI_ILIM_MASK),
DA9063_BUCK_COMMON_FIELDS(BPERI),
- .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBPERI_SEL),
},
{
DA9063_BUCK(DA9063, BCORES_MERGED, 300, 10, 1570,
@@ -508,7 +504,6 @@ static int da9063_ldo_set_suspend_mode(struct regulator_dev *rdev, unsigned mode
DA9063_REG_BUCK_ILIM_C, DA9063_BCORE1_ILIM_MASK),
/* BCORES_MERGED uses the same register fields as BCORE1 */
DA9063_BUCK_COMMON_FIELDS(BCORE1),
- .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBCORE1_SEL),
},
{
DA9063_BUCK(DA9063, BMEM_BIO_MERGED, 800, 20, 3340,
@@ -516,21 +511,17 @@ static int da9063_ldo_set_suspend_mode(struct regulator_dev *rdev, unsigned mode
DA9063_REG_BUCK_ILIM_A, DA9063_BMEM_ILIM_MASK),
/* BMEM_BIO_MERGED uses the same register fields as BMEM */
DA9063_BUCK_COMMON_FIELDS(BMEM),
- .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBMEM_SEL),
},
{
DA9063_LDO(DA9063, LDO3, 900, 20, 3440),
- .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VLDO3_SEL),
.oc_event = BFIELD(DA9063_REG_STATUS_D, DA9063_LDO3_LIM),
},
{
DA9063_LDO(DA9063, LDO7, 900, 50, 3600),
- .suspend = BFIELD(DA9063_REG_LDO7_CONT, DA9063_VLDO7_SEL),
.oc_event = BFIELD(DA9063_REG_STATUS_D, DA9063_LDO7_LIM),
},
{
DA9063_LDO(DA9063, LDO8, 900, 50, 3600),
- .suspend = BFIELD(DA9063_REG_LDO8_CONT, DA9063_VLDO8_SEL),
.oc_event = BFIELD(DA9063_REG_STATUS_D, DA9063_LDO8_LIM),
},
{
@@ -539,36 +530,29 @@ static int da9063_ldo_set_suspend_mode(struct regulator_dev *rdev, unsigned mode
},
{
DA9063_LDO(DA9063, LDO11, 900, 50, 3600),
- .suspend = BFIELD(DA9063_REG_LDO11_CONT, DA9063_VLDO11_SEL),
.oc_event = BFIELD(DA9063_REG_STATUS_D, DA9063_LDO11_LIM),
},
/* The following LDOs are present only on DA9063, not on DA9063L */
{
DA9063_LDO(DA9063, LDO1, 600, 20, 1860),
- .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VLDO1_SEL),
},
{
DA9063_LDO(DA9063, LDO2, 600, 20, 1860),
- .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VLDO2_SEL),
},
{
DA9063_LDO(DA9063, LDO4, 900, 20, 3440),
- .suspend = BFIELD(DA9063_REG_DVC_2, DA9063_VLDO4_SEL),
.oc_event = BFIELD(DA9063_REG_STATUS_D, DA9063_LDO4_LIM),
},
{
DA9063_LDO(DA9063, LDO5, 900, 50, 3600),
- .suspend = BFIELD(DA9063_REG_LDO5_CONT, DA9063_VLDO5_SEL),
},
{
DA9063_LDO(DA9063, LDO6, 900, 50, 3600),
- .suspend = BFIELD(DA9063_REG_LDO6_CONT, DA9063_VLDO6_SEL),
},
{
DA9063_LDO(DA9063, LDO10, 900, 50, 3600),
- .suspend = BFIELD(DA9063_REG_LDO10_CONT, DA9063_VLDO10_SEL),
},
};
--
1.9.1
Powered by blists - more mailing lists