| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20200317205017.28280-15-michael@walle.cc>
Date: Tue, 17 Mar 2020 21:50:13 +0100
From: Michael Walle <michael@...le.cc>
To: linux-gpio@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-hwmon@...r.kernel.org,
linux-pwm@...r.kernel.org, linux-watchdog@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org
Cc: Linus Walleij <linus.walleij@...aro.org>,
Bartosz Golaszewski <bgolaszewski@...libre.com>,
Rob Herring <robh+dt@...nel.org>,
Jean Delvare <jdelvare@...e.com>,
Guenter Roeck <linux@...ck-us.net>,
Lee Jones <lee.jones@...aro.org>,
Thierry Reding <thierry.reding@...il.com>,
Uwe Kleine-König
<u.kleine-koenig@...gutronix.de>,
Wim Van Sebroeck <wim@...ux-watchdog.org>,
Shawn Guo <shawnguo@...nel.org>, Li Yang <leoyang.li@....com>,
Thomas Gleixner <tglx@...utronix.de>,
Jason Cooper <jason@...edaemon.net>,
Marc Zyngier <maz@...nel.org>, Michael Walle <michael@...le.cc>
Subject: [PATCH 14/18] hwmon: add support for the sl28cpld hardware monitoring controller
This adds support for the hardware monitoring controller of the sl28cpld
board management controller. This driver is part of a multi-function
device.
Signed-off-by: Michael Walle <michael@...le.cc>
---
drivers/hwmon/Kconfig | 10 +++
drivers/hwmon/Makefile | 1 +
drivers/hwmon/sl28cpld-hwmon.c | 146 +++++++++++++++++++++++++++++++++
3 files changed, 157 insertions(+)
create mode 100644 drivers/hwmon/sl28cpld-hwmon.c
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 05a30832c6ba..c98716f78cfa 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -1412,6 +1412,16 @@ config SENSORS_RASPBERRYPI_HWMON
This driver can also be built as a module. If so, the module
will be called raspberrypi-hwmon.
+config SENSORS_SL28CPLD
+ tristate "Kontron's SMARC-sAL28 hardware monitoring driver"
+ depends on MFD_SL28CPLD
+ help
+ If you say yes here you get support for a fan connected to the
+ input of the SMARC connector of Kontron's SMARC-sAL28 module.
+
+ This driver can also be built as a module. If so, the module
+ will be called sl28cpld-hwmon.
+
config SENSORS_SHT15
tristate "Sensiron humidity and temperature sensors. SHT15 and compat."
depends on GPIOLIB || COMPILE_TEST
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index b0b9c8e57176..dfb0f8cda2dd 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -155,6 +155,7 @@ obj-$(CONFIG_SENSORS_S3C) += s3c-hwmon.o
obj-$(CONFIG_SENSORS_SCH56XX_COMMON)+= sch56xx-common.o
obj-$(CONFIG_SENSORS_SCH5627) += sch5627.o
obj-$(CONFIG_SENSORS_SCH5636) += sch5636.o
+obj-$(CONFIG_SENSORS_SL28CPLD) += sl28cpld-hwmon.o
obj-$(CONFIG_SENSORS_SHT15) += sht15.o
obj-$(CONFIG_SENSORS_SHT21) += sht21.o
obj-$(CONFIG_SENSORS_SHT3x) += sht3x.o
diff --git a/drivers/hwmon/sl28cpld-hwmon.c b/drivers/hwmon/sl28cpld-hwmon.c
new file mode 100644
index 000000000000..7ac42bb0a48c
--- /dev/null
+++ b/drivers/hwmon/sl28cpld-hwmon.c
@@ -0,0 +1,146 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * SMARC-sAL28 fan hardware monitoring driver.
+ *
+ * Copyright 2019 Kontron Europe GmbH
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/bitfield.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_address.h>
+#include <linux/regmap.h>
+#include <linux/platform_device.h>
+#include <linux/hwmon.h>
+
+#define FAN_INPUT 0
+#define FAN_SCALE_X8 BIT(7)
+#define FAN_VALUE_MASK GENMASK(6, 0)
+
+struct sl28cpld_hwmon {
+ struct regmap *regmap;
+ u32 offset;
+};
+
+static umode_t sl28cpld_hwmon_is_visible(const void *data,
+ enum hwmon_sensor_types type,
+ u32 attr, int channel)
+{
+ return 0444;
+}
+
+static int sl28cpld_hwmon_read(struct device *dev,
+ enum hwmon_sensor_types type, u32 attr,
+ int channel, long *input)
+{
+ struct sl28cpld_hwmon *hwmon = dev_get_drvdata(dev);
+ unsigned int value;
+ int ret;
+
+ switch (attr) {
+ case hwmon_fan_input:
+ ret = regmap_read(hwmon->regmap, hwmon->offset + FAN_INPUT,
+ &value);
+ if (ret)
+ return ret;
+ /*
+ * The register has a 7 bit value and 1 bit which indicates the
+ * scale. If the MSB is set, then the lower 7 bit has to be
+ * multiplied by 8, to get the correct reading.
+ */
+ if (value & FAN_SCALE_X8)
+ value = FIELD_GET(FAN_VALUE_MASK, value) << 3;
+
+ /*
+ * The counter period is 1000ms and the sysfs specification
+ * says we should asssume 2 pulses per revolution.
+ */
+ value *= 60 / 2;
+
+ break;
+ default:
+ return -EOPNOTSUPP;
+ }
+
+ *input = value;
+ return 0;
+}
+
+static const u32 sl28cpld_hwmon_fan_config[] = {
+ HWMON_F_INPUT,
+ 0
+};
+
+static const struct hwmon_channel_info sl28cpld_hwmon_fan = {
+ .type = hwmon_fan,
+ .config = sl28cpld_hwmon_fan_config,
+};
+
+static const struct hwmon_channel_info *sl28cpld_hwmon_info[] = {
+ &sl28cpld_hwmon_fan,
+ NULL
+};
+
+static const struct hwmon_ops sl28cpld_hwmon_ops = {
+ .is_visible = sl28cpld_hwmon_is_visible,
+ .read = sl28cpld_hwmon_read,
+};
+
+static const struct hwmon_chip_info sl28cpld_hwmon_chip_info = {
+ .ops = &sl28cpld_hwmon_ops,
+ .info = sl28cpld_hwmon_info,
+};
+
+static int sl28cpld_hwmon_probe(struct platform_device *pdev)
+{
+ struct device *hwmon_dev;
+ struct sl28cpld_hwmon *hwmon;
+ struct resource *res;
+
+ hwmon = devm_kzalloc(&pdev->dev, sizeof(*hwmon), GFP_KERNEL);
+ if (!hwmon)
+ return -ENOMEM;
+
+ if (!pdev->dev.parent)
+ return -ENODEV;
+
+ hwmon->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!hwmon->regmap)
+ return -ENODEV;
+
+ res = platform_get_resource(pdev, IORESOURCE_REG, 0);
+ if (!res)
+ return -EINVAL;
+ hwmon->offset = res->start;
+
+ hwmon_dev = devm_hwmon_device_register_with_info(&pdev->dev,
+ "sl28cpld_hwmon",
+ hwmon,
+ &sl28cpld_hwmon_chip_info,
+ NULL);
+ if (IS_ERR(hwmon_dev)) {
+ dev_err(&pdev->dev, "failed to register as hwmon device");
+ return PTR_ERR(hwmon_dev);
+ }
+
+ return 0;
+}
+
+static const struct platform_device_id sl28cpld_hwmon_id_table[] = {
+ {"sl28cpld-fan", 0},
+};
+MODULE_DEVICE_TABLE(platform, sl28cpld_hwmon_id_table);
+
+static struct platform_driver sl28cpld_hwmon_driver = {
+ .probe = sl28cpld_hwmon_probe,
+ .id_table = sl28cpld_hwmon_id_table,
+ .driver = {
+ .name = "sl28cpld-hwmon",
+ },
+};
+module_platform_driver(sl28cpld_hwmon_driver);
+
+MODULE_DESCRIPTION("sl28cpld Hardware Monitoring Driver");
+MODULE_LICENSE("GPL");
--
2.20.1
Powered by blists - more mailing lists