| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20200324102030.31000-11-narmstrong@baylibre.com>
Date: Tue, 24 Mar 2020 11:20:27 +0100
From: Neil Armstrong <narmstrong@...libre.com>
To: kishon@...com, balbi@...nel.org, khilman@...libre.com,
martin.blumenstingl@...glemail.com
Cc: linux-amlogic@...ts.infradead.org, linux-usb@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
Neil Armstrong <narmstrong@...libre.com>
Subject: [PATCH 10/13] phy: amlogic: meson-gxl-usb3: remove code for non-existing PHY
From: Martin Blumenstingl <martin.blumenstingl@...glemail.com>
The registers which are managed by the meson-gxl-usb3 PHY driver are
actually "USB control" registers (which are "glue" registers which
manage OTG detection and routing of the OTG capable port between the
DWC2 peripheral-only controller and the DWC3 host-only controller).
Drop the meson-gxl-usb3 PHY driver now that the dwc3-meson-g12a-usb
driver supports the USB control registers on GXL and GXM SoCs (these
were previously managed by the meson-gxl-usb3 PHY driver).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@...glemail.com>
Signed-off-by: Neil Armstrong <narmstrong@...libre.com>
---
.../bindings/phy/meson-gxl-usb3-phy.txt | 31 --
drivers/phy/amlogic/Kconfig | 12 -
drivers/phy/amlogic/Makefile | 1 -
drivers/phy/amlogic/phy-meson-gxl-usb3.c | 283 ------------------
4 files changed, 327 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/phy/meson-gxl-usb3-phy.txt
delete mode 100644 drivers/phy/amlogic/phy-meson-gxl-usb3.c
diff --git a/Documentation/devicetree/bindings/phy/meson-gxl-usb3-phy.txt b/Documentation/devicetree/bindings/phy/meson-gxl-usb3-phy.txt
deleted file mode 100644
index 114947e1de3d..000000000000
--- a/Documentation/devicetree/bindings/phy/meson-gxl-usb3-phy.txt
+++ /dev/null
@@ -1,31 +0,0 @@
-* Amlogic Meson GXL and GXM USB3 PHY and OTG detection binding
-
-Required properties:
-- compatible: Should be "amlogic,meson-gxl-usb3-phy"
-- #phys-cells: must be 0 (see phy-bindings.txt in this directory)
-- reg: The base address and length of the registers
-- interrupts: the interrupt specifier for the OTG detection
-- clocks: phandles to the clocks for
- - the USB3 PHY
- - and peripheral mode/OTG detection
-- clock-names: must contain "phy" and "peripheral"
-- resets: phandle to the reset lines for:
- - the USB3 PHY and
- - peripheral mode/OTG detection
-- reset-names: must contain "phy" and "peripheral"
-
-Optional properties:
-- phy-supply: see phy-bindings.txt in this directory
-
-
-Example:
- usb3_phy0: phy@...80 {
- compatible = "amlogic,meson-gxl-usb3-phy";
- #phy-cells = <0>;
- reg = <0x0 0x78080 0x0 0x20>;
- interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clkc CLKID_USB_OTG>, <&clkc_AO CLKID_AO_CEC_32K>;
- clock-names = "phy", "peripheral";
- resets = <&reset RESET_USB_OTG>, <&reset RESET_USB_OTG>;
- reset-names = "phy", "peripheral";
- };
diff --git a/drivers/phy/amlogic/Kconfig b/drivers/phy/amlogic/Kconfig
index af774ac2b934..77db9535ac6d 100644
--- a/drivers/phy/amlogic/Kconfig
+++ b/drivers/phy/amlogic/Kconfig
@@ -26,18 +26,6 @@ config PHY_MESON_GXL_USB2
GXL and GXM SoCs.
If unsure, say N.
-config PHY_MESON_GXL_USB3
- tristate "Meson GXL and GXM USB3 PHY drivers"
- default ARCH_MESON
- depends on OF && (ARCH_MESON || COMPILE_TEST)
- depends on USB_SUPPORT
- select GENERIC_PHY
- select REGMAP_MMIO
- help
- Enable this to support the Meson USB3 PHY and OTG detection
- IP block found in Meson GXL and GXM SoCs.
- If unsure, say N.
-
config PHY_MESON_G12A_USB2
tristate "Meson G12A USB2 PHY driver"
default ARCH_MESON
diff --git a/drivers/phy/amlogic/Makefile b/drivers/phy/amlogic/Makefile
index 11d1c42ac2be..8552e7153b99 100644
--- a/drivers/phy/amlogic/Makefile
+++ b/drivers/phy/amlogic/Makefile
@@ -2,5 +2,4 @@
obj-$(CONFIG_PHY_MESON8B_USB2) += phy-meson8b-usb2.o
obj-$(CONFIG_PHY_MESON_GXL_USB2) += phy-meson-gxl-usb2.o
obj-$(CONFIG_PHY_MESON_G12A_USB2) += phy-meson-g12a-usb2.o
-obj-$(CONFIG_PHY_MESON_GXL_USB3) += phy-meson-gxl-usb3.o
obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE) += phy-meson-g12a-usb3-pcie.o
diff --git a/drivers/phy/amlogic/phy-meson-gxl-usb3.c b/drivers/phy/amlogic/phy-meson-gxl-usb3.c
deleted file mode 100644
index c0e9e4c16149..000000000000
--- a/drivers/phy/amlogic/phy-meson-gxl-usb3.c
+++ /dev/null
@@ -1,283 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Meson GXL USB3 PHY and OTG mode detection driver
- *
- * Copyright (C) 2018 Martin Blumenstingl <martin.blumenstingl@...glemail.com>
- */
-
-#include <linux/bitfield.h>
-#include <linux/bitops.h>
-#include <linux/clk.h>
-#include <linux/module.h>
-#include <linux/of_device.h>
-#include <linux/phy/phy.h>
-#include <linux/regmap.h>
-#include <linux/reset.h>
-#include <linux/platform_device.h>
-
-#define USB_R0 0x00
- #define USB_R0_P30_FSEL_MASK GENMASK(5, 0)
- #define USB_R0_P30_PHY_RESET BIT(6)
- #define USB_R0_P30_TEST_POWERDOWN_HSP BIT(7)
- #define USB_R0_P30_TEST_POWERDOWN_SSP BIT(8)
- #define USB_R0_P30_ACJT_LEVEL_MASK GENMASK(13, 9)
- #define USB_R0_P30_TX_BOOST_LEVEL_MASK GENMASK(16, 14)
- #define USB_R0_P30_LANE0_TX2RX_LOOPBACK BIT(17)
- #define USB_R0_P30_LANE0_EXT_PCLK_REQ BIT(18)
- #define USB_R0_P30_PCS_RX_LOS_MASK_VAL_MASK GENMASK(28, 19)
- #define USB_R0_U2D_SS_SCALEDOWN_MODE_MASK GENMASK(30, 29)
- #define USB_R0_U2D_ACT BIT(31)
-
-#define USB_R1 0x04
- #define USB_R1_U3H_BIGENDIAN_GS BIT(0)
- #define USB_R1_U3H_PME_ENABLE BIT(1)
- #define USB_R1_U3H_HUB_PORT_OVERCURRENT_MASK GENMASK(6, 2)
- #define USB_R1_U3H_HUB_PORT_PERM_ATTACH_MASK GENMASK(11, 7)
- #define USB_R1_U3H_HOST_U2_PORT_DISABLE_MASK GENMASK(15, 12)
- #define USB_R1_U3H_HOST_U3_PORT_DISABLE BIT(16)
- #define USB_R1_U3H_HOST_PORT_POWER_CONTROL_PRESENT BIT(17)
- #define USB_R1_U3H_HOST_MSI_ENABLE BIT(18)
- #define USB_R1_U3H_FLADJ_30MHZ_REG_MASK GENMASK(24, 19)
- #define USB_R1_P30_PCS_TX_SWING_FULL_MASK GENMASK(31, 25)
-
-#define USB_R2 0x08
- #define USB_R2_P30_CR_DATA_IN_MASK GENMASK(15, 0)
- #define USB_R2_P30_CR_READ BIT(16)
- #define USB_R2_P30_CR_WRITE BIT(17)
- #define USB_R2_P30_CR_CAP_ADDR BIT(18)
- #define USB_R2_P30_CR_CAP_DATA BIT(19)
- #define USB_R2_P30_PCS_TX_DEEMPH_3P5DB_MASK GENMASK(25, 20)
- #define USB_R2_P30_PCS_TX_DEEMPH_6DB_MASK GENMASK(31, 26)
-
-#define USB_R3 0x0c
- #define USB_R3_P30_SSC_ENABLE BIT(0)
- #define USB_R3_P30_SSC_RANGE_MASK GENMASK(3, 1)
- #define USB_R3_P30_SSC_REF_CLK_SEL_MASK GENMASK(12, 4)
- #define USB_R3_P30_REF_SSP_EN BIT(13)
- #define USB_R3_P30_LOS_BIAS_MASK GENMASK(18, 16)
- #define USB_R3_P30_LOS_LEVEL_MASK GENMASK(23, 19)
- #define USB_R3_P30_MPLL_MULTIPLIER_MASK GENMASK(30, 24)
-
-#define USB_R4 0x10
- #define USB_R4_P21_PORT_RESET_0 BIT(0)
- #define USB_R4_P21_SLEEP_M0 BIT(1)
- #define USB_R4_MEM_PD_MASK GENMASK(3, 2)
- #define USB_R4_P21_ONLY BIT(4)
-
-#define USB_R5 0x14
- #define USB_R5_ID_DIG_SYNC BIT(0)
- #define USB_R5_ID_DIG_REG BIT(1)
- #define USB_R5_ID_DIG_CFG_MASK GENMASK(3, 2)
- #define USB_R5_ID_DIG_EN_0 BIT(4)
- #define USB_R5_ID_DIG_EN_1 BIT(5)
- #define USB_R5_ID_DIG_CURR BIT(6)
- #define USB_R5_ID_DIG_IRQ BIT(7)
- #define USB_R5_ID_DIG_TH_MASK GENMASK(15, 8)
- #define USB_R5_ID_DIG_CNT_MASK GENMASK(23, 16)
-
-/* read-only register */
-#define USB_R6 0x18
- #define USB_R6_P30_CR_DATA_OUT_MASK GENMASK(15, 0)
- #define USB_R6_P30_CR_ACK BIT(16)
-
-struct phy_meson_gxl_usb3_priv {
- struct regmap *regmap;
- enum phy_mode mode;
- struct clk *clk_phy;
- struct clk *clk_peripheral;
- struct reset_control *reset;
-};
-
-static const struct regmap_config phy_meson_gxl_usb3_regmap_conf = {
- .reg_bits = 8,
- .val_bits = 32,
- .reg_stride = 4,
- .max_register = USB_R6,
-};
-
-static int phy_meson_gxl_usb3_power_on(struct phy *phy)
-{
- struct phy_meson_gxl_usb3_priv *priv = phy_get_drvdata(phy);
-
- regmap_update_bits(priv->regmap, USB_R5, USB_R5_ID_DIG_EN_0,
- USB_R5_ID_DIG_EN_0);
- regmap_update_bits(priv->regmap, USB_R5, USB_R5_ID_DIG_EN_1,
- USB_R5_ID_DIG_EN_1);
- regmap_update_bits(priv->regmap, USB_R5, USB_R5_ID_DIG_TH_MASK,
- FIELD_PREP(USB_R5_ID_DIG_TH_MASK, 0xff));
-
- return 0;
-}
-
-static int phy_meson_gxl_usb3_power_off(struct phy *phy)
-{
- struct phy_meson_gxl_usb3_priv *priv = phy_get_drvdata(phy);
-
- regmap_update_bits(priv->regmap, USB_R5, USB_R5_ID_DIG_EN_0, 0);
- regmap_update_bits(priv->regmap, USB_R5, USB_R5_ID_DIG_EN_1, 0);
-
- return 0;
-}
-
-static int phy_meson_gxl_usb3_set_mode(struct phy *phy,
- enum phy_mode mode, int submode)
-{
- struct phy_meson_gxl_usb3_priv *priv = phy_get_drvdata(phy);
-
- switch (mode) {
- case PHY_MODE_USB_HOST:
- regmap_update_bits(priv->regmap, USB_R0, USB_R0_U2D_ACT, 0);
- regmap_update_bits(priv->regmap, USB_R4, USB_R4_P21_SLEEP_M0,
- 0);
- break;
-
- case PHY_MODE_USB_DEVICE:
- regmap_update_bits(priv->regmap, USB_R0, USB_R0_U2D_ACT,
- USB_R0_U2D_ACT);
- regmap_update_bits(priv->regmap, USB_R4, USB_R4_P21_SLEEP_M0,
- USB_R4_P21_SLEEP_M0);
- break;
-
- default:
- dev_err(&phy->dev, "unsupported PHY mode %d\n", mode);
- return -EINVAL;
- }
-
- priv->mode = mode;
-
- return 0;
-}
-
-static int phy_meson_gxl_usb3_init(struct phy *phy)
-{
- struct phy_meson_gxl_usb3_priv *priv = phy_get_drvdata(phy);
- int ret;
-
- ret = reset_control_reset(priv->reset);
- if (ret)
- goto err;
-
- ret = clk_prepare_enable(priv->clk_phy);
- if (ret)
- goto err;
-
- ret = clk_prepare_enable(priv->clk_peripheral);
- if (ret)
- goto err_disable_clk_phy;
-
- ret = phy_meson_gxl_usb3_set_mode(phy, priv->mode, 0);
- if (ret)
- goto err_disable_clk_peripheral;
-
- regmap_update_bits(priv->regmap, USB_R1,
- USB_R1_U3H_FLADJ_30MHZ_REG_MASK,
- FIELD_PREP(USB_R1_U3H_FLADJ_30MHZ_REG_MASK, 0x20));
-
- return 0;
-
-err_disable_clk_peripheral:
- clk_disable_unprepare(priv->clk_peripheral);
-err_disable_clk_phy:
- clk_disable_unprepare(priv->clk_phy);
-err:
- return ret;
-}
-
-static int phy_meson_gxl_usb3_exit(struct phy *phy)
-{
- struct phy_meson_gxl_usb3_priv *priv = phy_get_drvdata(phy);
-
- clk_disable_unprepare(priv->clk_peripheral);
- clk_disable_unprepare(priv->clk_phy);
-
- return 0;
-}
-
-static const struct phy_ops phy_meson_gxl_usb3_ops = {
- .power_on = phy_meson_gxl_usb3_power_on,
- .power_off = phy_meson_gxl_usb3_power_off,
- .set_mode = phy_meson_gxl_usb3_set_mode,
- .init = phy_meson_gxl_usb3_init,
- .exit = phy_meson_gxl_usb3_exit,
- .owner = THIS_MODULE,
-};
-
-static int phy_meson_gxl_usb3_probe(struct platform_device *pdev)
-{
- struct device *dev = &pdev->dev;
- struct device_node *np = dev->of_node;
- struct phy_meson_gxl_usb3_priv *priv;
- struct resource *res;
- struct phy *phy;
- struct phy_provider *phy_provider;
- void __iomem *base;
- int ret;
-
- priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
- if (!priv)
- return -ENOMEM;
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- base = devm_ioremap_resource(dev, res);
- if (IS_ERR(base))
- return PTR_ERR(base);
-
- priv->regmap = devm_regmap_init_mmio(dev, base,
- &phy_meson_gxl_usb3_regmap_conf);
- if (IS_ERR(priv->regmap))
- return PTR_ERR(priv->regmap);
-
- priv->clk_phy = devm_clk_get(dev, "phy");
- if (IS_ERR(priv->clk_phy))
- return PTR_ERR(priv->clk_phy);
-
- priv->clk_peripheral = devm_clk_get(dev, "peripheral");
- if (IS_ERR(priv->clk_peripheral))
- return PTR_ERR(priv->clk_peripheral);
-
- priv->reset = devm_reset_control_array_get_shared(dev);
- if (IS_ERR(priv->reset))
- return PTR_ERR(priv->reset);
-
- /*
- * default to host mode as hardware defaults and/or boot-loader
- * behavior can result in this PHY starting up in device mode. this
- * default and the initialization in phy_meson_gxl_usb3_init ensure
- * that we reproducibly start in a known mode on all devices.
- */
- priv->mode = PHY_MODE_USB_HOST;
-
- phy = devm_phy_create(dev, np, &phy_meson_gxl_usb3_ops);
- if (IS_ERR(phy)) {
- ret = PTR_ERR(phy);
- if (ret != -EPROBE_DEFER)
- dev_err(dev, "failed to create PHY\n");
-
- return ret;
- }
-
- phy_set_drvdata(phy, priv);
-
- phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
-
- return PTR_ERR_OR_ZERO(phy_provider);
-}
-
-static const struct of_device_id phy_meson_gxl_usb3_of_match[] = {
- { .compatible = "amlogic,meson-gxl-usb3-phy", },
- { },
-};
-MODULE_DEVICE_TABLE(of, phy_meson_gxl_usb3_of_match);
-
-static struct platform_driver phy_meson_gxl_usb3_driver = {
- .probe = phy_meson_gxl_usb3_probe,
- .driver = {
- .name = "phy-meson-gxl-usb3",
- .of_match_table = phy_meson_gxl_usb3_of_match,
- },
-};
-module_platform_driver(phy_meson_gxl_usb3_driver);
-
-MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@...glemail.com>");
-MODULE_DESCRIPTION("Meson GXL USB3 PHY and OTG detection driver");
-MODULE_LICENSE("GPL v2");
--
2.22.0
Powered by blists - more mailing lists