| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20200325071157.GA4760@pendragon.ideasonboard.com>
Date: Wed, 25 Mar 2020 09:11:57 +0200
From: Laurent Pinchart <laurent.pinchart@...asonboard.com>
To: Dafna Hirschfeld <dafna3@...il.com>
Cc: Hans Verkuil <hverkuil@...all.nl>,
Helen Koike <helen.koike@...labora.com>,
hans.verkuil@...co.com, linux-rockchip@...ts.infradead.org,
devicetree@...r.kernel.org, eddie.cai.linux@...il.com,
mchehab@...nel.org, heiko@...ech.de, jacob2.chen@...k-chips.com,
jeffy.chen@...k-chips.com, zyc@...k-chips.com,
linux-kernel@...r.kernel.org, Tomasz Figa <tfiga@...omium.org>,
sakari.ailus@...ux.intel.com, kernel@...labora.com,
Ezequiel Garcia <ezequiel@...labora.com>,
Linux Media Mailing List <linux-media@...r.kernel.org>,
linux-arm-kernel@...ts.infradead.org, zhengsq@...k-chips.com,
Jacob Chen <cc@...k-chips.com>,
Allon Huang <allon.huang@...k-chips.com>
Subject: Re: [PATCH v8 05/14] media: rkisp1: add Rockchip ISP1 subdev driver
Hi Dafna,
On Wed, Mar 25, 2020 at 07:34:37AM +0100, Dafna Hirschfeld wrote:
> On Thu, Aug 15, 2019 at 10:17 PM Laurent Pinchart wrote:
> > On Wed, Aug 07, 2019 at 12:39:17PM +0200, Hans Verkuil wrote:
> > > On 8/6/19 8:51 PM, Helen Koike wrote:
> > > > On 7/30/19 3:42 PM, Helen Koike wrote:
> > > >> From: Jacob Chen <jacob2.chen@...k-chips.com>
> > > >>
> > > >> Add the subdev driver for rockchip isp1.
> > > >>
> > > >> Signed-off-by: Jacob Chen <jacob2.chen@...k-chips.com>
> > > >> Signed-off-by: Shunqian Zheng <zhengsq@...k-chips.com>
> > > >> Signed-off-by: Yichong Zhong <zyc@...k-chips.com>
> > > >> Signed-off-by: Jacob Chen <cc@...k-chips.com>
> > > >> Signed-off-by: Eddie Cai <eddie.cai.linux@...il.com>
> > > >> Signed-off-by: Jeffy Chen <jeffy.chen@...k-chips.com>
> > > >> Signed-off-by: Allon Huang <allon.huang@...k-chips.com>
> > > >> Signed-off-by: Tomasz Figa <tfiga@...omium.org>
> > > >> [fixed unknown entity type / switched to PIXEL_RATE]
> > > >> Signed-off-by: Ezequiel Garcia <ezequiel@...labora.com>
> > > >> [update for upstream]
> > > >> Signed-off-by: Helen Koike <helen.koike@...labora.com>
> > > >>
> > > >> ---
> > > >>
> > > >> Changes in v8: None
> > > >> Changes in v7:
> > > >> - fixed warning because of unknown entity type
> > > >> - fixed v4l2-compliance errors regarding rkisp1 formats, try formats
> > > >> and default values
> > > >> - fix typo riksp1/rkisp1
> > > >> - redesign: remove mipi/csi subdevice, sensors connect directly to the
> > > >> isp subdevice in the media topology now. As a consequence, remove the
> > > >> hack in mipidphy_g_mbus_config() where information from the sensor was
> > > >> being propagated through the topology.
> > > >> - From the old dphy:
> > > >> * cache get_remote_sensor() in s_stream
> > > >> * use V4L2_CID_PIXEL_RATE instead of V4L2_CID_LINK_FREQ
> > > >> - Replace stream state with a boolean
> > > >> - code styling and checkpatch fixes
> > > >> - fix stop_stream (return after calling stop, do not reenable the stream)
> > > >> - fix rkisp1_isp_sd_get_selection when V4L2_SUBDEV_FORMAT_TRY is set
> > > >> - fix get format in output (isp_sd->out_fmt.mbus_code was being ignored)
> > > >> - s/intput/input
> > > >> - remove #define sd_to_isp_sd(_sd), add a static inline as it will be
> > > >> reused by the capture
> > > >>
> > > >> drivers/media/platform/rockchip/isp1/rkisp1.c | 1286 +++++++++++++++++
> > > >> drivers/media/platform/rockchip/isp1/rkisp1.h | 111 ++
> > > >> 2 files changed, 1397 insertions(+)
> > > >> create mode 100644 drivers/media/platform/rockchip/isp1/rkisp1.c
> > > >> create mode 100644 drivers/media/platform/rockchip/isp1/rkisp1.h
> > > >>
> > > >> diff --git a/drivers/media/platform/rockchip/isp1/rkisp1.c b/drivers/media/platform/rockchip/isp1/rkisp1.c
> > > >> new file mode 100644
> > > >> index 000000000000..6d0c0ffb5e03
> > > >> --- /dev/null
> > > >> +++ b/drivers/media/platform/rockchip/isp1/rkisp1.c
> > > >> @@ -0,0 +1,1286 @@
> > >
> > > <snip>
> > >
> > > >> +static int rkisp1_isp_sd_get_fmt(struct v4l2_subdev *sd,
> > > >> + struct v4l2_subdev_pad_config *cfg,
> > > >> + struct v4l2_subdev_format *fmt)
> > > >> +{
> > > >> + struct rkisp1_isp_subdev *isp_sd = sd_to_isp_sd(sd);
> > > >> + struct v4l2_mbus_framefmt *mf = &fmt->format;
> > > >> +
> > > >> + if ((fmt->pad != RKISP1_ISP_PAD_SINK) &&
> > > >> + (fmt->pad != RKISP1_ISP_PAD_SOURCE_PATH)) {
> > > >> + fmt->format.code = MEDIA_BUS_FMT_FIXED;
> > > >> + /*
> > > >> + * NOTE: setting a format here doesn't make much sense
> > > >> + * but v4l2-compliance complains
> > > >> + */
> > > >> + fmt->format.width = RKISP1_DEFAULT_WIDTH;
> > > >> + fmt->format.height = RKISP1_DEFAULT_HEIGHT;
> > > >
> > > > As I had mentioned to you, this is called for the isp pads connected to the
> > > > DMA engines for statistics and parameters (meta data).
> > > >
> > > > If I remove those, I get the following errors:
> > > >
> > > > Sub-Device ioctls (Sink Pad 1):
> > > > test Try VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK
> > > > fail: v4l2-test-subdevs.cpp(311): fmt.width == 0 || fmt.width > 65536
> > > > fail: v4l2-test-subdevs.cpp(356): checkMBusFrameFmt(node, fmt.format)
> > > > test Try VIDIOC_SUBDEV_G/S_FMT: FAIL
> > > > test Try VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK
> > > > test Active VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK
> > > > fail: v4l2-test-subdevs.cpp(311): fmt.width == 0 || fmt.width > 65536
> > > > fail: v4l2-test-subdevs.cpp(356): checkMBusFrameFmt(node, fmt.format)
> > > > test Active VIDIOC_SUBDEV_G/S_FMT: FAIL
> > > > test Active VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK
> > > > test VIDIOC_SUBDEV_G/S_FRAME_INTERVAL: OK (Not Supported)
> > > >
> > > > Here is the full log: http://ix.io/1QNt
> > > >
> > > > Is this a bug in v4l2-compliance?
> > >
> > > Yes and no :-)
> > >
> > > Currently v4l2-compliance assumes that only video is transferred over a media bus.
> > > But that's not the case here, and testing the code field doesn't help v4l2-compliance
> > > since MEDIA_BUS_FMT_FIXED is also still used by some older subdev drivers for video.
> > >
> > > I think we need a new bus format: MEDIA_BUS_FMT_FIXED_METADATA. Then v4l2-compliance
> > > can tell it apart from the regular fixed video bus format.
> >
> > Wouldn't a pad flag that identifies the type of data transmitted by a
> > pad be a better, backward-compatible option ? This could be useful for
> > audio as well.
>
> Hi,
> Can you explain what pad flag do you mean?
> Do you mean adding a flag in the 'MEDIA_LNK_FL_*' list ?
I meant MEDIA_PAD_FL_*. We could reserve a few bits in
media_pad_desc.flags to tell what type of data is being transported.
> Also, some valid value should be set to 'fmt->format.code' so with
> the flags solution
> that you suggest it should stay MEDIA_BUS_FMT_FIXED ?
Correct.
> > > If I do a 'git grep MEDIA_BUS_FMT_FIXED' then I see that it is also in use by vsp1
> > > for histogram information, so that should also be converted to use the new FIXED_METADATA
> > > format, although that might be too late (there might be userspace complications).
> >
> > Yes, probably not a good idea.
> >
> > > >> + fmt->format.field = V4L2_FIELD_NONE;
> > > >> + return 0;
> > > >> + }
> > > >> +
> > > >> + if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> > > >> + mf = v4l2_subdev_get_try_format(sd, cfg, fmt->pad);
> > > >> + fmt->format = *mf;
> > > >> + return 0;
> > > >> + }
> > > >> +
> > > >> + if (fmt->pad == RKISP1_ISP_PAD_SINK) {
> > > >> + *mf = isp_sd->in_frm;
> > > >> + } else if (fmt->pad == RKISP1_ISP_PAD_SOURCE_PATH) {
> > > >> + /* format of source pad */
> > > >> + *mf = isp_sd->in_frm;
> > > >> + mf->code = isp_sd->out_fmt.mbus_code;
> > > >> + /* window size of source pad */
> > > >> + mf->width = isp_sd->out_crop.width;
> > > >> + mf->height = isp_sd->out_crop.height;
> > > >> + mf->quantization = isp_sd->quantization;
> > > >> + }
> > > >> + mf->field = V4L2_FIELD_NONE;
> > > >> +
> > > >> + return 0;
> > > >> +}
--
Regards,
Laurent Pinchart
Powered by blists - more mailing lists