[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <20200331085420.412999332@linuxfoundation.org>
Date: Tue, 31 Mar 2020 10:57:38 +0200
From: Greg Kroah-Hartman <gregkh@...uxfoundation.org>
To: linux-kernel@...r.kernel.org
Cc: Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
stable@...r.kernel.org, Andrew Smith <andrew.smith@...i.com>,
René van Dorst <opensource@...rst.com>,
Vivien Didelot <vivien.didelot@...il.com>,
Florian Fainelli <f.fainelli@...il.com>,
"David S. Miller" <davem@...emloft.net>
Subject: [PATCH 5.4 018/155] net: dsa: mt7530: Change the LINK bit to reflect the link status
From: "René van Dorst" <opensource@...rst.com>
[ Upstream commit 22259471b51925353bd7b16f864c79fdd76e425e ]
Andrew reported:
After a number of network port link up/down changes, sometimes the switch
port gets stuck in a state where it thinks it is still transmitting packets
but the cpu port is not actually transmitting anymore. In this state you
will see a message on the console
"mtk_soc_eth 1e100000.ethernet eth0: transmit timed out" and the Tx counter
in ifconfig will be incrementing on virtual port, but not incrementing on
cpu port.
The issue is that MAC TX/RX status has no impact on the link status or
queue manager of the switch. So the queue manager just queues up packets
of a disabled port and sends out pause frames when the queue is full.
Change the LINK bit to reflect the link status.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Reported-by: Andrew Smith <andrew.smith@...i.com>
Signed-off-by: René van Dorst <opensource@...rst.com>
Reviewed-by: Vivien Didelot <vivien.didelot@...il.com>
Reviewed-by: Florian Fainelli <f.fainelli@...il.com>
Signed-off-by: David S. Miller <davem@...emloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@...uxfoundation.org>
---
drivers/net/dsa/mt7530.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -566,7 +566,7 @@ mt7530_mib_reset(struct dsa_switch *ds)
static void
mt7530_port_set_status(struct mt7530_priv *priv, int port, int enable)
{
- u32 mask = PMCR_TX_EN | PMCR_RX_EN;
+ u32 mask = PMCR_TX_EN | PMCR_RX_EN | PMCR_FORCE_LNK;
if (enable)
mt7530_set(priv, MT7530_PMCR_P(port), mask);
@@ -1439,7 +1439,7 @@ static void mt7530_phylink_mac_config(st
mcr_new &= ~(PMCR_FORCE_SPEED_1000 | PMCR_FORCE_SPEED_100 |
PMCR_FORCE_FDX | PMCR_TX_FC_EN | PMCR_RX_FC_EN);
mcr_new |= PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | PMCR_BACKOFF_EN |
- PMCR_BACKPR_EN | PMCR_FORCE_MODE | PMCR_FORCE_LNK;
+ PMCR_BACKPR_EN | PMCR_FORCE_MODE;
/* Are we connected to external phy */
if (port == 5 && dsa_is_user_port(ds, 5))
Powered by blists - more mailing lists