| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <4268fa5d-f32d-6231-287c-7ffb159c1b34@intel.com>
Date: Thu, 2 Apr 2020 13:11:03 +0300
From: Adrian Hunter <adrian.hunter@...el.com>
To: Manish Narani <manish.narani@...inx.com>, ulf.hansson@...aro.org,
robh+dt@...nel.org, mark.rutland@....com, michal.simek@...inx.com
Cc: linux-mmc@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
git@...inx.com
Subject: Re: [PATCH v2 2/4] sdhci: arasan: Add support for Versal Tap Delays
On 30/03/20 8:41 am, Manish Narani wrote:
> Add support to set tap delays for Xilinx Versal SD controller. The tap
> delay registers have moved to SD controller space in Versal. Make the
> changes accordingly.
>
> Signed-off-by: Manish Narani <manish.narani@...inx.com>
Acked-by: Adrian Hunter <adrian.hunter@...el.com>
> ---
> drivers/mmc/host/sdhci-of-arasan.c | 175 +++++++++++++++++++++++++++++
> 1 file changed, 175 insertions(+)
>
> diff --git a/drivers/mmc/host/sdhci-of-arasan.c b/drivers/mmc/host/sdhci-of-arasan.c
> index 0146d7dd315b..34403b2cac97 100644
> --- a/drivers/mmc/host/sdhci-of-arasan.c
> +++ b/drivers/mmc/host/sdhci-of-arasan.c
> @@ -28,15 +28,26 @@
> #include "sdhci-pltfm.h"
>
> #define SDHCI_ARASAN_VENDOR_REGISTER 0x78
> +
> +#define SDHCI_ARASAN_ITAPDLY_REGISTER 0xF0F8
> +#define SDHCI_ARASAN_OTAPDLY_REGISTER 0xF0FC
> +
> #define SDHCI_ARASAN_CQE_BASE_ADDR 0x200
> #define VENDOR_ENHANCED_STROBE BIT(0)
>
> #define PHY_CLK_TOO_SLOW_HZ 400000
>
> +#define SDHCI_ITAPDLY_CHGWIN 0x200
> +#define SDHCI_ITAPDLY_ENABLE 0x100
> +#define SDHCI_OTAPDLY_ENABLE 0x40
> +
> /* Default settings for ZynqMP Clock Phases */
> #define ZYNQMP_ICLK_PHASE {0, 63, 63, 0, 63, 0, 0, 183, 54, 0, 0}
> #define ZYNQMP_OCLK_PHASE {0, 72, 60, 0, 60, 72, 135, 48, 72, 135, 0}
>
> +#define VERSAL_ICLK_PHASE {0, 132, 132, 0, 132, 0, 0, 162, 90, 0, 0}
> +#define VERSAL_OCLK_PHASE {0, 60, 48, 0, 48, 72, 90, 36, 60, 90, 0}
> +
> /*
> * On some SoCs the syscon area has a feature where the upper 16-bits of
> * each 32-bit register act as a write mask for the lower 16-bits. This allows
> @@ -566,6 +577,10 @@ static const struct of_device_id sdhci_arasan_of_match[] = {
> .compatible = "xlnx,zynqmp-8.9a",
> .data = &sdhci_arasan_zynqmp_data,
> },
> + {
> + .compatible = "xlnx,versal-8.9a",
> + .data = &sdhci_arasan_zynqmp_data,
> + },
> { /* sentinel */ }
> };
> MODULE_DEVICE_TABLE(of, sdhci_arasan_of_match);
> @@ -768,6 +783,152 @@ static const struct clk_ops zynqmp_sampleclk_ops = {
> .set_phase = sdhci_zynqmp_sampleclk_set_phase,
> };
>
> +/**
> + * sdhci_versal_sdcardclk_set_phase - Set the SD Output Clock Tap Delays
> + *
> + * Set the SD Output Clock Tap Delays for Output path
> + *
> + * @hw: Pointer to the hardware clock structure.
> + * @degrees The clock phase shift between 0 - 359.
> + * Return: 0 on success and error value on error
> + */
> +static int sdhci_versal_sdcardclk_set_phase(struct clk_hw *hw, int degrees)
> +{
> + struct sdhci_arasan_clk_data *clk_data =
> + container_of(hw, struct sdhci_arasan_clk_data, sdcardclk_hw);
> + struct sdhci_arasan_data *sdhci_arasan =
> + container_of(clk_data, struct sdhci_arasan_data, clk_data);
> + struct sdhci_host *host = sdhci_arasan->host;
> + u8 tap_delay, tap_max = 0;
> + int ret;
> +
> + /*
> + * This is applicable for SDHCI_SPEC_300 and above
> + * Versal does not set phase for <=25MHz clock.
> + * If degrees is zero, no need to do anything.
> + */
> + if (host->version < SDHCI_SPEC_300 ||
> + host->timing == MMC_TIMING_LEGACY ||
> + host->timing == MMC_TIMING_UHS_SDR12 || !degrees)
> + return 0;
> +
> + switch (host->timing) {
> + case MMC_TIMING_MMC_HS:
> + case MMC_TIMING_SD_HS:
> + case MMC_TIMING_UHS_SDR25:
> + case MMC_TIMING_UHS_DDR50:
> + case MMC_TIMING_MMC_DDR52:
> + /* For 50MHz clock, 30 Taps are available */
> + tap_max = 30;
> + break;
> + case MMC_TIMING_UHS_SDR50:
> + /* For 100MHz clock, 15 Taps are available */
> + tap_max = 15;
> + break;
> + case MMC_TIMING_UHS_SDR104:
> + case MMC_TIMING_MMC_HS200:
> + /* For 200MHz clock, 8 Taps are available */
> + tap_max = 8;
> + default:
> + break;
> + }
> +
> + tap_delay = (degrees * tap_max) / 360;
> +
> + /* Set the Clock Phase */
> + if (tap_delay) {
> + u32 regval;
> +
> + regval = sdhci_readl(host, SDHCI_ARASAN_OTAPDLY_REGISTER);
> + regval |= SDHCI_OTAPDLY_ENABLE;
> + sdhci_writel(host, regval, SDHCI_ARASAN_OTAPDLY_REGISTER);
> + regval |= tap_delay;
> + sdhci_writel(host, regval, SDHCI_ARASAN_OTAPDLY_REGISTER);
> + }
> +
> + return ret;
> +}
> +
> +static const struct clk_ops versal_sdcardclk_ops = {
> + .recalc_rate = sdhci_arasan_sdcardclk_recalc_rate,
> + .set_phase = sdhci_versal_sdcardclk_set_phase,
> +};
> +
> +/**
> + * sdhci_versal_sampleclk_set_phase - Set the SD Input Clock Tap Delays
> + *
> + * Set the SD Input Clock Tap Delays for Input path
> + *
> + * @hw: Pointer to the hardware clock structure.
> + * @degrees The clock phase shift between 0 - 359.
> + * Return: 0 on success and error value on error
> + */
> +static int sdhci_versal_sampleclk_set_phase(struct clk_hw *hw, int degrees)
> +{
> + struct sdhci_arasan_clk_data *clk_data =
> + container_of(hw, struct sdhci_arasan_clk_data, sampleclk_hw);
> + struct sdhci_arasan_data *sdhci_arasan =
> + container_of(clk_data, struct sdhci_arasan_data, clk_data);
> + struct sdhci_host *host = sdhci_arasan->host;
> + u8 tap_delay, tap_max = 0;
> + int ret;
> +
> + /*
> + * This is applicable for SDHCI_SPEC_300 and above
> + * Versal does not set phase for <=25MHz clock.
> + * If degrees is zero, no need to do anything.
> + */
> + if (host->version < SDHCI_SPEC_300 ||
> + host->timing == MMC_TIMING_LEGACY ||
> + host->timing == MMC_TIMING_UHS_SDR12 || !degrees)
> + return 0;
> +
> + switch (host->timing) {
> + case MMC_TIMING_MMC_HS:
> + case MMC_TIMING_SD_HS:
> + case MMC_TIMING_UHS_SDR25:
> + case MMC_TIMING_UHS_DDR50:
> + case MMC_TIMING_MMC_DDR52:
> + /* For 50MHz clock, 120 Taps are available */
> + tap_max = 120;
> + break;
> + case MMC_TIMING_UHS_SDR50:
> + /* For 100MHz clock, 60 Taps are available */
> + tap_max = 60;
> + break;
> + case MMC_TIMING_UHS_SDR104:
> + case MMC_TIMING_MMC_HS200:
> + /* For 200MHz clock, 30 Taps are available */
> + tap_max = 30;
> + default:
> + break;
> + }
> +
> + tap_delay = (degrees * tap_max) / 360;
> +
> + /* Set the Clock Phase */
> + if (tap_delay) {
> + u32 regval;
> +
> + regval = sdhci_readl(host, SDHCI_ARASAN_ITAPDLY_REGISTER);
> + regval |= SDHCI_ITAPDLY_CHGWIN;
> + sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER);
> + regval |= SDHCI_ITAPDLY_ENABLE;
> + sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER);
> + regval |= tap_delay;
> + sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER);
> + regval &= ~SDHCI_ITAPDLY_CHGWIN;
> + sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER);
> + }
> +
> + return ret;
> +}
> +
> +static const struct clk_ops versal_sampleclk_ops = {
> + .recalc_rate = sdhci_arasan_sampleclk_recalc_rate,
> + .set_phase = sdhci_versal_sampleclk_set_phase,
> +};
> +
> static void arasan_zynqmp_dll_reset(struct sdhci_host *host, u32 deviceid)
> {
> struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> @@ -965,6 +1126,16 @@ static void arasan_dt_parse_clk_phases(struct device *dev,
> }
> }
>
> + if (of_device_is_compatible(dev->of_node, "xlnx,versal-8.9a")) {
> + iclk_phase = (int [MMC_TIMING_MMC_HS400 + 1]) VERSAL_ICLK_PHASE;
> + oclk_phase = (int [MMC_TIMING_MMC_HS400 + 1]) VERSAL_OCLK_PHASE;
> +
> + for (i = 0; i <= MMC_TIMING_MMC_HS400; i++) {
> + clk_data->clk_phase_in[i] = iclk_phase[i];
> + clk_data->clk_phase_out[i] = oclk_phase[i];
> + }
> + }
> +
> arasan_dt_read_clk_phase(dev, clk_data, MMC_TIMING_LEGACY,
> "clk-phase-legacy");
> arasan_dt_read_clk_phase(dev, clk_data, MMC_TIMING_MMC_HS,
> @@ -1025,6 +1196,8 @@ sdhci_arasan_register_sdcardclk(struct sdhci_arasan_data *sdhci_arasan,
> sdcardclk_init.flags = CLK_GET_RATE_NOCACHE;
> if (of_device_is_compatible(np, "xlnx,zynqmp-8.9a"))
> sdcardclk_init.ops = &zynqmp_sdcardclk_ops;
> + else if (of_device_is_compatible(np, "xlnx,versal-8.9a"))
> + sdcardclk_init.ops = &versal_sdcardclk_ops;
> else
> sdcardclk_init.ops = &arasan_sdcardclk_ops;
>
> @@ -1077,6 +1250,8 @@ sdhci_arasan_register_sampleclk(struct sdhci_arasan_data *sdhci_arasan,
> sampleclk_init.flags = CLK_GET_RATE_NOCACHE;
> if (of_device_is_compatible(np, "xlnx,zynqmp-8.9a"))
> sampleclk_init.ops = &zynqmp_sampleclk_ops;
> + else if (of_device_is_compatible(np, "xlnx,versal-8.9a"))
> + sampleclk_init.ops = &versal_sampleclk_ops;
> else
> sampleclk_init.ops = &arasan_sampleclk_ops;
>
>
Powered by blists - more mailing lists