| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <ef7e8f03-0a43-156e-b86e-3ab3887f0245@ti.com>
Date: Fri, 3 Apr 2020 14:37:49 -0500
From: Dan Murphy <dmurphy@...com>
To: Lubomir Rintel <lkundrak@...sk>,
Jacek Anaszewski <jacek.anaszewski@...il.com>
CC: Pavel Machek <pavel@....cz>, <linux-kernel@...r.kernel.org>,
<linux-leds@...r.kernel.org>
Subject: Re: [PATCH v3] leds: ariel: Add driver for status LEDs on Dell Wyse
3020
Lubomir
On 3/22/20 2:41 AM, Lubomir Rintel wrote:
> This adds support for controlling the LEDs attached to the Embedded
> Controller on a Dell Wyse 3020 "Ariel" board.
>
> Signed-off-by: Lubomir Rintel <lkundrak@...sk>
>
> ---
> Changes since v2:
> - Hopefully sending out the correct patch this time...
>
> Changes since v1:
> - Reduce code duplication with a loop
> - Drop "ariel:" prefix from led names
> - Do not print a message after a successful probe
> ---
> drivers/leds/Kconfig | 11 ++++
> drivers/leds/Makefile | 1 +
> drivers/leds/leds-ariel.c | 133 ++++++++++++++++++++++++++++++++++++++
> 3 files changed, 145 insertions(+)
> create mode 100644 drivers/leds/leds-ariel.c
>
> diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
> index d82f1dea37111..66424ee54cc01 100644
> --- a/drivers/leds/Kconfig
> +++ b/drivers/leds/Kconfig
> @@ -83,6 +83,17 @@ config LEDS_APU
> To compile this driver as a module, choose M here: the
> module will be called leds-apu.
>
> +config LEDS_ARIEL
> + tristate "Dell Wyse 3020 status LED support"
> + depends on LEDS_CLASS
> + depends on (MACH_MMP3_DT && MFD_ENE_KB3930) || COMPILE_TEST
> + help
> + This driver adds support for controlling the front panel status
> + LEDs on Dell Wyse 3020 (Ariel) board via the KB3930 Embedded
> + Controller.
> +
> + Say Y to if your machine is a Dell Wyse 3020 thin client.
> +
> config LEDS_AS3645A
> tristate "AS3645A and LM3555 LED flash controllers support"
> depends on I2C && LEDS_CLASS_FLASH
> diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
> index d7e1107753fb1..bf3b22038d113 100644
> --- a/drivers/leds/Makefile
> +++ b/drivers/leds/Makefile
> @@ -10,6 +10,7 @@ obj-$(CONFIG_LEDS_TRIGGERS) += led-triggers.o
> obj-$(CONFIG_LEDS_88PM860X) += leds-88pm860x.o
> obj-$(CONFIG_LEDS_AAT1290) += leds-aat1290.o
> obj-$(CONFIG_LEDS_APU) += leds-apu.o
> +obj-$(CONFIG_LEDS_ARIEL) += leds-ariel.o
> obj-$(CONFIG_LEDS_AS3645A) += leds-as3645a.o
> obj-$(CONFIG_LEDS_AN30259A) += leds-an30259a.o
> obj-$(CONFIG_LEDS_BCM6328) += leds-bcm6328.o
> diff --git a/drivers/leds/leds-ariel.c b/drivers/leds/leds-ariel.c
> new file mode 100644
> index 0000000000000..8fc56722e12f4
> --- /dev/null
> +++ b/drivers/leds/leds-ariel.c
> @@ -0,0 +1,133 @@
> +// SPDX-License-Identifier: BSD-2-Clause OR GPL-2.0-or-later
> +/*
> + * Dell Wyse 3020 a.k.a. "Ariel" Embedded Controller LED Driver
> + *
> + * Copyright (C) 2020 Lubomir Rintel
> + */
> +
> +#include <linux/module.h>
> +#include <linux/leds.h>
> +#include <linux/regmap.h>
> +#include <linux/of_platform.h>
> +
> +enum ec_index {
> + EC_BLUE_LED = 0x01,
> + EC_AMBER_LED = 0x02,
Defining the value after the 0x0 is unnecessary as enums are incremental
only the first value needs to be defined if the following values are in
numerical order
Can these also be #defined instead of an enum? Not requesting them to
be just wondering about the design decision here.
> + EC_GREEN_LED = 0x03,
> +};
> +
> +enum {
> + EC_LED_OFF = 0x00,
> + EC_LED_STILL = 0x01,
Same comment as above
> + EC_LED_FADE = 0x02,
> + EC_LED_BLINK = 0x03,
> +};
> +
> +struct ariel_led {
> + struct regmap *ec_ram;
> + enum ec_index ec_index;
> + struct led_classdev led_cdev;
> +};
> +
> +#define led_cdev_to_ariel_led(c) container_of(c, struct ariel_led, led_cdev)
> +
> +static enum led_brightness ariel_led_get(struct led_classdev *led_cdev)
> +{
> + struct ariel_led *led = led_cdev_to_ariel_led(led_cdev);
> + unsigned int led_status = 0;
> +
> + if (regmap_read(led->ec_ram, led->ec_index, &led_status))
> + return LED_OFF;
> +
> + if (led_status == EC_LED_STILL)
> + return LED_FULL;
> + else
else is not needed here
> + return LED_OFF;
> +}
> +
> +static void ariel_led_set(struct led_classdev *led_cdev,
> + enum led_brightness brightness)
> +{
> + struct ariel_led *led = led_cdev_to_ariel_led(led_cdev);
> +
> + if (brightness == LED_OFF)
> + regmap_write(led->ec_ram, led->ec_index, EC_LED_OFF);
> + else
> + regmap_write(led->ec_ram, led->ec_index, EC_LED_STILL);
> +}
> +
> +static int ariel_blink_set(struct led_classdev *led_cdev,
> + unsigned long *delay_on, unsigned long *delay_off)
> +{
> + struct ariel_led *led = led_cdev_to_ariel_led(led_cdev);
> +
> + if (*delay_on == 0 && *delay_off == 0)
> + return -EINVAL;
> +
> + if (*delay_on == 0) {
> + regmap_write(led->ec_ram, led->ec_index, EC_LED_OFF);
> + } else if (*delay_off == 0) {
> + regmap_write(led->ec_ram, led->ec_index, EC_LED_STILL);
> + } else {
> + *delay_on = 500;
> + *delay_off = 500;
> + regmap_write(led->ec_ram, led->ec_index, EC_LED_BLINK);
> + }
> +
> + return 0;
> +}
> +
> +#define NLEDS 3
This define needs to be more unique.
Something like EC_NLEDS or EC_NUM_LEDS and should be moved to the top of
the file under the #includes
> +
> +static int ariel_led_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct ariel_led *leds;
> + struct regmap *ec_ram;
> + int ret;
> + int i;
> +
> + leds = devm_kcalloc(dev, NLEDS, sizeof(*leds), GFP_KERNEL);
> + if (!leds)
> + return -ENOMEM;
> +
> + ec_ram = dev_get_regmap(dev->parent, "ec_ram");
Maybe this should be checked before memory is allocated.
> + if (!ec_ram)
> + return -ENODEV;
> +
> + leds[0].ec_index = EC_BLUE_LED;
> + leds[0].led_cdev.name = "blue:power",
> + leds[0].led_cdev.default_trigger = "default-on";
> +
> + leds[1].ec_index = EC_AMBER_LED;
> + leds[1].led_cdev.name = "amber:status",
> +
> + leds[2].ec_index = EC_GREEN_LED;
> + leds[2].led_cdev.name = "green:status",
> + leds[2].led_cdev.default_trigger = "default-on";
> +
> + for (i = 0; i < NLEDS; i++) {
I don't understand this loop. i is incremented but never used.
should the below be leds[i]?
> + leds[0].ec_ram = ec_ram;
> + leds[0].led_cdev.brightness_get = ariel_led_get;
> + leds[0].led_cdev.brightness_set = ariel_led_set;
> + leds[0].led_cdev.blink_set = ariel_blink_set;
> +
> + ret = devm_led_classdev_register(dev, &leds[0].led_cdev);
> + if (ret)
> + return ret;
> + }
> +
Dan
Powered by blists - more mailing lists