linux-kernel - [PATCH] ARM: dts: enable WLAN for Mecer Xtreme Mini S6

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [thread-next>] [day] [month] [year] [list]

Message-Id: <20200405110022.3849-1-justin.swartz@risingedge.co.za>
Date:   Sun,  5 Apr 2020 11:00:21 +0000
From:   Justin Swartz <justin.swartz@...ingedge.co.za>
To:     Heiko Stuebner <heiko@...ech.de>, Rob Herring <robh+dt@...nel.org>,
        Mark Rutland <mark.rutland@....com>
Cc:     Justin Swartz <justin.swartz@...ingedge.co.za>,
        linux-arm-kernel@...ts.infradead.org,
        linux-rockchip@...ts.infradead.org, devicetree@...r.kernel.org,
        linux-kernel@...r.kernel.org
Subject: [PATCH] ARM: dts: enable WLAN for Mecer Xtreme Mini S6

The Mecer Xtreme Mini S6 features a wireless module, based on a
Realtek 8723BS, which provides WLAN and Bluetooth connectivity via
SDIO and UART interfaces respectively.

Define a simple MMC power sequence that declares the GPIO pins
connected to the module's WLAN Disable and Bluetooth Disable pins
as active low reset signals, because both signals must be deasserted
for WLAN radio operation.

Configure the host's SDIO interface for High Speed mode with 1.8v
I/O signalling and IRQ detection over a 4-bit wide bus.

Signed-off-by: Justin Swartz <justin.swartz@...ingedge.co.za>
---
 arch/arm/boot/dts/rk3229-xms6.dts | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm/boot/dts/rk3229-xms6.dts b/arch/arm/boot/dts/rk3229-xms6.dts
index 679fc2b00..cdfcef41b 100644
--- a/arch/arm/boot/dts/rk3229-xms6.dts
+++ b/arch/arm/boot/dts/rk3229-xms6.dts
@@ -39,6 +39,12 @@
 		};
 	};
 
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>,
+		              <&gpio2 29 GPIO_ACTIVE_LOW>;
+	};
+
 	vcc_host: vcc-host-regulator {
 		compatible = "regulator-fixed";
 		enable-active-high;
@@ -202,6 +208,18 @@
 	status = "okay";
 };
 
+&sdio {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	disable-wp;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	num-slots = <1>;
+	vqmmc-supply = <&vccio_1v8>;
+	status = "okay";
+};
+
 &sdmmc {
 	cap-mmc-highspeed;
 	disable-wp;
-- 
2.11.0