Message-Id: <1586942266-21480-4-git-send-email-jprakash@codeaurora.org>
Date:   Wed, 15 Apr 2020 14:47:46 +0530
From:   Jishnu Prakash <jprakash@...eaurora.org>
To:     agross@...nel.org, bjorn.andersson@...aro.org,
        devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
        mka@...omium.org, linus.walleij@...aro.org,
        Jonathan.Cameron@...wei.com, smohanad@...eaurora.org,
        kgunda@...eaurora.org, aghayal@...eaurora.org,
        Jonathan Cameron <jic23@...nel.org>,
        Hartmut Knaack <knaack.h@....de>,
        Lars-Peter Clausen <lars@...afoo.de>,
        Peter Meerwald-Stadler <pmeerw@...erw.net>,
        linux-arm-msm@...r.kernel.org, linux-iio@...r.kernel.org
Cc:     linux-arm-msm-owner@...r.kernel.org,
        Jishnu Prakash <jprakash@...eaurora.org>
Subject: [PATCH V2 3/3] iio: adc: Add support for PMIC7 ADC

The ADC architecture on PMIC7 is changed as compared to PMIC5. The
major change from PMIC5 is that all SW communication to ADC goes through
PMK8350, which communicates with other PMICs through PBS when the ADC
on PMK8350 works in master mode. The SID register is used to identify the
PMICs with which the PBS needs to communicate. Add support for the same.

Signed-off-by: Jishnu Prakash <jprakash@...eaurora.org>
---
 drivers/iio/adc/qcom-spmi-adc5.c   | 257 ++++++++++++++++++++++++++++++++++--
 drivers/iio/adc/qcom-vadc-common.c | 258 +++++++++++++++++++++++++++++++++++++
 drivers/iio/adc/qcom-vadc-common.h |  15 +++
 3 files changed, 517 insertions(+), 13 deletions(-)

diff --git a/drivers/iio/adc/qcom-spmi-adc5.c b/drivers/iio/adc/qcom-spmi-adc5.c
index 21fdcde..8d86ed0 100644
--- a/drivers/iio/adc/qcom-spmi-adc5.c
+++ b/drivers/iio/adc/qcom-spmi-adc5.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2018, 2020, The Linux Foundation. All rights reserved.
  */
 
 #include <linux/bitops.h>
@@ -23,6 +23,7 @@
 
 #define ADC5_USR_REVISION1			0x0
 #define ADC5_USR_STATUS1			0x8
+#define ADC5_USR_STATUS1_CONV_FAULT		BIT(7)
 #define ADC5_USR_STATUS1_REQ_STS		BIT(1)
 #define ADC5_USR_STATUS1_EOC			BIT(0)
 #define ADC5_USR_STATUS1_REQ_STS_EOC_MASK	0x3
@@ -65,6 +66,9 @@
 
 #define ADC5_USR_IBAT_DATA1			0x53
 
+#define ADC_CHANNEL_OFFSET			0x8
+#define ADC_CHANNEL_MASK			GENMASK(7, 0)
+
 /*
  * Conversion time varies based on the decimation, clock rate, fast average
  * samples and measurements queued across different VADC peripherals.
@@ -79,6 +83,11 @@
 #define ADC5_HW_SETTLE_DIFF_MINOR		3
 #define ADC5_HW_SETTLE_DIFF_MAJOR		5
 
+/* For PMIC7 */
+#define ADC_APP_SID				0x40
+#define ADC_APP_SID_MASK			GENMASK(3, 0)
+#define ADC7_CONV_TIMEOUT			msecs_to_jiffies(10)
+
 enum adc5_cal_method {
 	ADC5_NO_CAL = 0,
 	ADC5_RATIOMETRIC_CAL,
@@ -96,6 +105,7 @@ enum adc5_cal_val {
  * @cal_method: calibration method.
  * @cal_val: calibration value
  * @decimation: sampling rate supported for the channel.
+ * @sid: slave id of PMIC owning the channel, for PMIC7.
  * @prescale: channel scaling performed on the input signal.
  * @hw_settle_time: the time between AMUX being configured and the
  *	start of conversion.
@@ -110,6 +120,7 @@ struct adc5_channel_prop {
 	enum adc5_cal_method	cal_method;
 	enum adc5_cal_val	cal_val;
 	unsigned int		decimation;
+	unsigned int		sid;
 	unsigned int		prescale;
 	unsigned int		hw_settle_time;
 	unsigned int		avg_samples;
@@ -140,6 +151,7 @@ struct adc5_chip {
 	bool			poll_eoc;
 	struct completion	complete;
 	struct mutex		lock;
+	int			irq_eoc;
 	const struct adc5_data	*data;
 };
 
@@ -155,6 +167,8 @@ static const struct vadc_prescale_ratio adc5_prescale_ratios[] = {
 	{.num =  1, .den = 16}
 };
 
+static const struct adc5_data adc7_data_pmic;
+
 static int adc5_read(struct adc5_chip *adc, u16 offset, u8 *data, int len)
 {
 	return regmap_bulk_read(adc->regmap, adc->base + offset, data, len);
@@ -165,6 +179,11 @@ static int adc5_write(struct adc5_chip *adc, u16 offset, u8 *data, int len)
 	return regmap_bulk_write(adc->regmap, adc->base + offset, data, len);
 }
 
+static int adc5_masked_write(struct adc5_chip *adc, u16 offset, u8 mask, u8 val)
+{
+	return regmap_update_bits(adc->regmap, adc->base + offset, mask, val);
+}
+
 static int adc5_prescaling_from_dt(u32 num, u32 den)
 {
 	unsigned int pre;
@@ -230,11 +249,11 @@ static int adc5_read_voltage_data(struct adc5_chip *adc, u16 *data)
 	*data = (rslt_msb << 8) | rslt_lsb;
 
 	if (*data == ADC5_USR_DATA_CHECK) {
-		pr_err("Invalid data:0x%x\n", *data);
+		dev_err(adc->dev, "Invalid data:0x%x\n", *data);
 		return -EINVAL;
 	}
 
-	pr_debug("voltage raw code:0x%x\n", *data);
+	dev_dbg(adc->dev, "voltage raw code:0x%x\n", *data);
 
 	return 0;
 }
@@ -314,6 +333,47 @@ static int adc5_configure(struct adc5_chip *adc,
 	return adc5_write(adc, ADC5_USR_DIG_PARAM, buf, sizeof(buf));
 }
 
+static int adc7_configure(struct adc5_chip *adc,
+			struct adc5_channel_prop *prop)
+{
+	int ret;
+	u8 conv_req = 0, buf[4];
+
+	ret = adc5_masked_write(adc, ADC_APP_SID, ADC_APP_SID_MASK, prop->sid);
+	if (ret)
+		return ret;
+
+	ret = adc5_read(adc, ADC5_USR_DIG_PARAM, buf, sizeof(buf));
+	if (ret < 0)
+		return ret;
+
+	/* Digital param selection */
+	adc5_update_dig_param(adc, prop, &buf[0]);
+
+	/* Update fast average sample value */
+	buf[1] &= 0xff & ~ADC5_USR_FAST_AVG_CTL_SAMPLES_MASK;
+	buf[1] |= prop->avg_samples;
+
+	/* Select ADC channel */
+	buf[2] = prop->channel;
+
+	/* Select HW settle delay for channel */
+	buf[3] &= 0xff & ~ADC5_USR_HW_SETTLE_DELAY_MASK;
+	buf[3] |= prop->hw_settle_time;
+
+	/* Select CONV request */
+	conv_req = ADC5_USR_CONV_REQ_REQ;
+
+	if (!adc->poll_eoc)
+		reinit_completion(&adc->complete);
+
+	ret = adc5_write(adc, ADC5_USR_DIG_PARAM, buf, sizeof(buf));
+	if (ret)
+		return ret;
+
+	return adc5_write(adc, ADC5_USR_CONV_REQ, &conv_req, 1);
+}
+
 static int adc5_do_conversion(struct adc5_chip *adc,
 			struct adc5_channel_prop *prop,
 			struct iio_chan_spec const *chan,
@@ -325,24 +385,24 @@ static int adc5_do_conversion(struct adc5_chip *adc,
 
 	ret = adc5_configure(adc, prop);
 	if (ret) {
-		pr_err("ADC configure failed with %d\n", ret);
+		dev_err(adc->dev, "ADC configure failed with %d\n", ret);
 		goto unlock;
 	}
 
 	if (adc->poll_eoc) {
 		ret = adc5_poll_wait_eoc(adc);
 		if (ret < 0) {
-			pr_err("EOC bit not set\n");
+			dev_err(adc->dev, "EOC bit not set\n");
 			goto unlock;
 		}
 	} else {
 		ret = wait_for_completion_timeout(&adc->complete,
 							ADC5_CONV_TIMEOUT);
 		if (!ret) {
-			pr_debug("Did not get completion timeout.\n");
+			dev_dbg(adc->dev, "Did not get completion timeout.\n");
 			ret = adc5_poll_wait_eoc(adc);
 			if (ret < 0) {
-				pr_err("EOC bit not set\n");
+				dev_err(adc->dev, "EOC bit not set\n");
 				goto unlock;
 			}
 		}
@@ -355,6 +415,43 @@ static int adc5_do_conversion(struct adc5_chip *adc,
 	return ret;
 }
 
+static int adc7_do_conversion(struct adc5_chip *adc,
+			struct adc5_channel_prop *prop,
+			struct iio_chan_spec const *chan,
+			u16 *data_volt, u16 *data_cur)
+{
+	int ret;
+	u8 status = 0;
+
+	mutex_lock(&adc->lock);
+
+	ret = adc7_configure(adc, prop);
+	if (ret) {
+		dev_err(adc->dev, "ADC configure failed with %d\n", ret);
+		goto unlock;
+	}
+
+	/* No support for polling mode at present*/
+	wait_for_completion_timeout(&adc->complete, ADC7_CONV_TIMEOUT);
+
+	ret = adc5_read(adc, ADC5_USR_STATUS1, &status, 1);
+	if (ret < 0)
+		goto unlock;
+
+	if (status & ADC5_USR_STATUS1_CONV_FAULT) {
+		dev_err(adc->dev, "Unexpected conversion fault\n");
+		ret = -EIO;
+		goto unlock;
+	}
+
+	ret = adc5_read_voltage_data(adc, data_volt);
+
+unlock:
+	mutex_unlock(&adc->lock);
+
+	return ret;
+}
+
 static irqreturn_t adc5_isr(int irq, void *dev_id)
 {
 	struct adc5_chip *adc = dev_id;
@@ -377,6 +474,56 @@ static int adc5_of_xlate(struct iio_dev *indio_dev,
 	return -EINVAL;
 }
 
+static int adc7_of_xlate(struct iio_dev *indio_dev,
+				const struct of_phandle_args *iiospec)
+{
+	struct adc5_chip *adc = iio_priv(indio_dev);
+	int i, v_channel;
+
+	for (i = 0; i < adc->nchannels; i++) {
+		v_channel = (adc->chan_props[i].sid << ADC_CHANNEL_OFFSET |
+			adc->chan_props[i].channel);
+		if (v_channel == iiospec->args[0])
+			return i;
+	}
+
+	return -EINVAL;
+}
+
+static int adc7_read_raw(struct iio_dev *indio_dev,
+			 struct iio_chan_spec const *chan, int *val, int *val2,
+			 long mask)
+{
+	struct adc5_chip *adc = iio_priv(indio_dev);
+	struct adc5_channel_prop *prop;
+	u16 adc_code_volt, adc_code_cur;
+	int ret;
+
+	prop = &adc->chan_props[chan->address];
+
+	switch (mask) {
+	case IIO_CHAN_INFO_PROCESSED:
+		ret = adc7_do_conversion(adc, prop, chan,
+					&adc_code_volt, &adc_code_cur);
+		if (ret)
+			return ret;
+
+		ret = qcom_adc5_hw_scale(prop->scale_fn_type,
+			&adc5_prescale_ratios[prop->prescale],
+			adc->data,
+			adc_code_volt, val);
+
+		if (ret)
+			return ret;
+
+		return IIO_VAL_INT;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
 static int adc5_read_raw(struct iio_dev *indio_dev,
 			 struct iio_chan_spec const *chan, int *val, int *val2,
 			 long mask)
@@ -415,6 +562,11 @@ static const struct iio_info adc5_info = {
 	.of_xlate = adc5_of_xlate,
 };
 
+static const struct iio_info adc7_info = {
+	.read_raw = adc7_read_raw,
+	.of_xlate = adc7_of_xlate,
+};
+
 struct adc5_channels {
 	const char *datasheet_name;
 	unsigned int prescale_index;
@@ -477,6 +629,39 @@ static const struct adc5_channels adc5_chans_pmic[ADC5_MAX_CHANNEL] = {
 					SCALE_HW_CALIB_PM5_SMB_TEMP)
 };
 
+static const struct adc5_channels adc7_chans_pmic[ADC5_MAX_CHANNEL] = {
+	[ADC7_REF_GND]		= ADC5_CHAN_VOLT("ref_gnd", 0,
+					SCALE_HW_CALIB_DEFAULT)
+	[ADC7_1P25VREF]		= ADC5_CHAN_VOLT("vref_1p25", 0,
+					SCALE_HW_CALIB_DEFAULT)
+	[ADC7_VPH_PWR]		= ADC5_CHAN_VOLT("vph_pwr", 1,
+					SCALE_HW_CALIB_DEFAULT)
+	[ADC7_VBAT_SNS]		= ADC5_CHAN_VOLT("vbat_sns", 3,
+					SCALE_HW_CALIB_DEFAULT)
+	[ADC7_DIE_TEMP]		= ADC5_CHAN_TEMP("die_temp", 0,
+					SCALE_HW_CALIB_PMIC_THERM_PM7)
+	[ADC7_AMUX_THM1_100K_PU]	= ADC5_CHAN_TEMP("amux_thm1_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC7_AMUX_THM2_100K_PU]	= ADC5_CHAN_TEMP("amux_thm2_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC7_AMUX_THM3_100K_PU]	= ADC5_CHAN_TEMP("amux_thm3_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC7_AMUX_THM4_100K_PU]	= ADC5_CHAN_TEMP("amux_thm4_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC7_AMUX_THM5_100K_PU]	= ADC5_CHAN_TEMP("amux_thm5_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC7_AMUX_THM6_100K_PU]	= ADC5_CHAN_TEMP("amux_thm6_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC7_GPIO1_100K_PU]	= ADC5_CHAN_TEMP("gpio1_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC7_GPIO2_100K_PU]	= ADC5_CHAN_TEMP("gpio2_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC7_GPIO3_100K_PU]	= ADC5_CHAN_TEMP("gpio3_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC7_GPIO4_100K_PU]	= ADC5_CHAN_TEMP("gpio4_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+};
+
 static const struct adc5_channels adc5_chans_rev2[ADC5_MAX_CHANNEL] = {
 	[ADC5_REF_GND]		= ADC5_CHAN_VOLT("ref_gnd", 0,
 					SCALE_HW_CALIB_DEFAULT)
@@ -511,6 +696,7 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
 {
 	const char *name = node->name, *channel_name;
 	u32 chan, value, varr[2];
+	u32 sid = 0;
 	int ret;
 	struct device *dev = adc->dev;
 
@@ -520,6 +706,15 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
 		return ret;
 	}
 
+	/*
+	 * Value read from "reg" is virtual channel number
+	 * virtual channel number = (sid << 8 | channel number).
+	 */
+	if (adc->data == &adc7_data_pmic) {
+		sid = chan >> ADC_CHANNEL_OFFSET;
+		chan = chan & ADC_CHANNEL_MASK;
+	}
+
 	if (chan > ADC5_PARALLEL_ISENSE_VBAT_IDATA ||
 	    !data->adc_chans[chan].datasheet_name) {
 		dev_err(dev, "%s invalid channel number %d\n", name, chan);
@@ -528,11 +723,12 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
 
 	/* the channel has DT description */
 	prop->channel = chan;
+	prop->sid = sid;
 
 	channel_name = of_get_property(node,
 				"label", NULL) ? : node->name;
 	if (!channel_name) {
-		pr_err("Invalid channel name\n");
+		dev_err(dev,"Invalid channel name\n");
 		return -EINVAL;
 	}
 	prop->datasheet_name = channel_name;
@@ -575,11 +771,12 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
 			return ret;
 		}
 
-		pr_debug("dig_ver:minor:%d, major:%d\n", dig_version[0],
+		dev_dbg(adc->dev, "dig_ver:minor:%d, major:%d\n", dig_version[0],
 						dig_version[1]);
 		/* Digital controller >= 5.3 have hw_settle_2 option */
-		if (dig_version[0] >= ADC5_HW_SETTLE_DIFF_MINOR &&
-			dig_version[1] >= ADC5_HW_SETTLE_DIFF_MAJOR)
+		if ((dig_version[0] >= ADC5_HW_SETTLE_DIFF_MINOR &&
+			dig_version[1] >= ADC5_HW_SETTLE_DIFF_MAJOR) ||
+			adc->data == &adc7_data_pmic)
 			ret = adc5_hw_settle_time_from_dt(value,
 							data->hw_settle_2);
 		else
@@ -629,6 +826,7 @@ static const struct adc5_data adc5_data_pmic = {
 	.full_scale_code_volt = 0x70e4,
 	.full_scale_code_cur = 0x2710,
 	.adc_chans = adc5_chans_pmic,
+	.info = &adc5_info,
 	.decimation = (unsigned int [ADC5_DECIMATION_SAMPLES_MAX])
 				{250, 420, 840},
 	.hw_settle_1 = (unsigned int [VADC_HW_SETTLE_SAMPLES_MAX])
@@ -639,10 +837,23 @@ static const struct adc5_data adc5_data_pmic = {
 				1, 2, 4, 8, 16, 32, 64, 128},
 };
 
+static const struct adc5_data adc7_data_pmic = {
+	.full_scale_code_volt = 0x70e4,
+	.adc_chans = adc7_chans_pmic,
+	.info = &adc7_info,
+	.decimation = (unsigned int [ADC5_DECIMATION_SAMPLES_MAX])
+				{85, 340, 1360},
+	.hw_settle_2 = (unsigned int [VADC_HW_SETTLE_SAMPLES_MAX])
+				{15, 100, 200, 300, 400, 500, 600, 700,
+				1000, 2000, 4000, 8000, 16000, 32000,
+				64000, 128000},
+};
+
 static const struct adc5_data adc5_data_pmic_rev2 = {
 	.full_scale_code_volt = 0x4000,
 	.full_scale_code_cur = 0x1800,
 	.adc_chans = adc5_chans_rev2,
+	.info = &adc5_info,
 	.decimation = (unsigned int [ADC5_DECIMATION_SAMPLES_MAX])
 				{256, 512, 1024},
 	.hw_settle_1 = (unsigned int [VADC_HW_SETTLE_SAMPLES_MAX])
@@ -659,6 +870,10 @@ static const struct of_device_id adc5_match_table[] = {
 		.data = &adc5_data_pmic,
 	},
 	{
+		.compatible = "qcom,spmi-adc7",
+		.data = &adc7_data_pmic,
+	},
+	{
 		.compatible = "qcom,spmi-adc-rev2",
 		.data = &adc5_data_pmic_rev2,
 	},
@@ -752,15 +967,20 @@ static int adc5_probe(struct platform_device *pdev)
 	adc->regmap = regmap;
 	adc->dev = dev;
 	adc->base = reg;
+
+	platform_set_drvdata(pdev, adc);
+
 	init_completion(&adc->complete);
 	mutex_init(&adc->lock);
 
 	ret = adc5_get_dt_data(adc, node);
 	if (ret) {
-		pr_err("adc get dt data failed\n");
+		dev_err(dev, "adc get dt data failed\n");
 		return ret;
 	}
 
+	indio_dev->info = adc->data->info;
+
 	irq_eoc = platform_get_irq(pdev, 0);
 	if (irq_eoc < 0) {
 		if (irq_eoc == -EPROBE_DEFER || irq_eoc == -EINVAL)
@@ -773,23 +993,34 @@ static int adc5_probe(struct platform_device *pdev)
 			return ret;
 	}
 
+	adc->irq_eoc = irq_eoc;
+
 	indio_dev->dev.parent = dev;
 	indio_dev->dev.of_node = node;
 	indio_dev->name = pdev->name;
 	indio_dev->modes = INDIO_DIRECT_MODE;
-	indio_dev->info = &adc5_info;
 	indio_dev->channels = adc->iio_chans;
 	indio_dev->num_channels = adc->nchannels;
 
 	return devm_iio_device_register(dev, indio_dev);
 }
 
+static int adc5_exit(struct platform_device *pdev)
+{
+	struct adc5_chip *adc = platform_get_drvdata(pdev);
+
+	if (adc->irq_eoc >= 0)
+		disable_irq(adc->irq_eoc);
+	return 0;
+}
+
 static struct platform_driver adc5_driver = {
 	.driver = {
 		.name = "qcom-spmi-adc5.c",
 		.of_match_table = adc5_match_table,
 	},
 	.probe = adc5_probe,
+	.remove = adc5_exit,
 };
 module_platform_driver(adc5_driver);
 
diff --git a/drivers/iio/adc/qcom-vadc-common.c b/drivers/iio/adc/qcom-vadc-common.c
index 2bb78d1..2194029 100644
--- a/drivers/iio/adc/qcom-vadc-common.c
+++ b/drivers/iio/adc/qcom-vadc-common.c
@@ -89,6 +89,195 @@ static const struct vadc_map_pt adcmap_100k_104ef_104fb_1875_vref[] = {
 	{ 46,	125000 },
 };
 
+static const struct vadc_map_pt adcmap7_die_temp[] = {
+	{ 433700, 1967},
+	{ 473100, 1964},
+	{ 512400, 1957},
+	{ 551500, 1949},
+	{ 590500, 1940},
+	{ 629300, 1930},
+	{ 667900, 1921},
+	{ 706400, 1910},
+	{ 744600, 1896},
+	{ 782500, 1878},
+	{ 820100, 1859},
+	{ 857300, 0},
+};
+
+/*
+ * Resistance to temperature table for 100k pull up for NTCG104EF104.
+ */
+static const struct vadc_map_pt adcmap7_100k[] = {
+	{ 4250657, -40960 },
+	{ 3962085, -39936 },
+	{ 3694875, -38912 },
+	{ 3447322, -37888 },
+	{ 3217867, -36864 },
+	{ 3005082, -35840 },
+	{ 2807660, -34816 },
+	{ 2624405, -33792 },
+	{ 2454218, -32768 },
+	{ 2296094, -31744 },
+	{ 2149108, -30720 },
+	{ 2012414, -29696 },
+	{ 1885232, -28672 },
+	{ 1766846, -27648 },
+	{ 1656598, -26624 },
+	{ 1553884, -25600 },
+	{ 1458147, -24576 },
+	{ 1368873, -23552 },
+	{ 1285590, -22528 },
+	{ 1207863, -21504 },
+	{ 1135290, -20480 },
+	{ 1067501, -19456 },
+	{ 1004155, -18432 },
+	{ 944935, -17408 },
+	{ 889550, -16384 },
+	{ 837731, -15360 },
+	{ 789229, -14336 },
+	{ 743813, -13312 },
+	{ 701271, -12288 },
+	{ 661405, -11264 },
+	{ 624032, -10240 },
+	{ 588982, -9216 },
+	{ 556100, -8192 },
+	{ 525239, -7168 },
+	{ 496264, -6144 },
+	{ 469050, -5120 },
+	{ 443480, -4096 },
+	{ 419448, -3072 },
+	{ 396851, -2048 },
+	{ 375597, -1024 },
+	{ 355598, 0 },
+	{ 336775, 1024 },
+	{ 319052, 2048 },
+	{ 302359, 3072 },
+	{ 286630, 4096 },
+	{ 271806, 5120 },
+	{ 257829, 6144 },
+	{ 244646, 7168 },
+	{ 232209, 8192 },
+	{ 220471, 9216 },
+	{ 209390, 10240 },
+	{ 198926, 11264 },
+	{ 189040, 12288 },
+	{ 179698, 13312 },
+	{ 170868, 14336 },
+	{ 162519, 15360 },
+	{ 154622, 16384 },
+	{ 147150, 17408 },
+	{ 140079, 18432 },
+	{ 133385, 19456 },
+	{ 127046, 20480 },
+	{ 121042, 21504 },
+	{ 115352, 22528 },
+	{ 109960, 23552 },
+	{ 104848, 24576 },
+	{ 100000, 25600 },
+	{ 95402, 26624 },
+	{ 91038, 27648 },
+	{ 86897, 28672 },
+	{ 82965, 29696 },
+	{ 79232, 30720 },
+	{ 75686, 31744 },
+	{ 72316, 32768 },
+	{ 69114, 33792 },
+	{ 66070, 34816 },
+	{ 63176, 35840 },
+	{ 60423, 36864 },
+	{ 57804, 37888 },
+	{ 55312, 38912 },
+	{ 52940, 39936 },
+	{ 50681, 40960 },
+	{ 48531, 41984 },
+	{ 46482, 43008 },
+	{ 44530, 44032 },
+	{ 42670, 45056 },
+	{ 40897, 46080 },
+	{ 39207, 47104 },
+	{ 37595, 48128 },
+	{ 36057, 49152 },
+	{ 34590, 50176 },
+	{ 33190, 51200 },
+	{ 31853, 52224 },
+	{ 30577, 53248 },
+	{ 29358, 54272 },
+	{ 28194, 55296 },
+	{ 27082, 56320 },
+	{ 26020, 57344 },
+	{ 25004, 58368 },
+	{ 24033, 59392 },
+	{ 23104, 60416 },
+	{ 22216, 61440 },
+	{ 21367, 62464 },
+	{ 20554, 63488 },
+	{ 19776, 64512 },
+	{ 19031, 65536 },
+	{ 18318, 66560 },
+	{ 17636, 67584 },
+	{ 16982, 68608 },
+	{ 16355, 69632 },
+	{ 15755, 70656 },
+	{ 15180, 71680 },
+	{ 14628, 72704 },
+	{ 14099, 73728 },
+	{ 13592, 74752 },
+	{ 13106, 75776 },
+	{ 12640, 76800 },
+	{ 12192, 77824 },
+	{ 11762, 78848 },
+	{ 11350, 79872 },
+	{ 10954, 80896 },
+	{ 10574, 81920 },
+	{ 10209, 82944 },
+	{ 9858, 83968 },
+	{ 9521, 84992 },
+	{ 9197, 86016 },
+	{ 8886, 87040 },
+	{ 8587, 88064 },
+	{ 8299, 89088 },
+	{ 8023, 90112 },
+	{ 7757, 91136 },
+	{ 7501, 92160 },
+	{ 7254, 93184 },
+	{ 7017, 94208 },
+	{ 6789, 95232 },
+	{ 6570, 96256 },
+	{ 6358, 97280 },
+	{ 6155, 98304 },
+	{ 5959, 99328 },
+	{ 5770, 100352 },
+	{ 5588, 101376 },
+	{ 5412, 102400 },
+	{ 5243, 103424 },
+	{ 5080, 104448 },
+	{ 4923, 105472 },
+	{ 4771, 106496 },
+	{ 4625, 107520 },
+	{ 4484, 108544 },
+	{ 4348, 109568 },
+	{ 4217, 110592 },
+	{ 4090, 111616 },
+	{ 3968, 112640 },
+	{ 3850, 113664 },
+	{ 3736, 114688 },
+	{ 3626, 115712 },
+	{ 3519, 116736 },
+	{ 3417, 117760 },
+	{ 3317, 118784 },
+	{ 3221, 119808 },
+	{ 3129, 120832 },
+	{ 3039, 121856 },
+	{ 2952, 122880 },
+	{ 2868, 123904 },
+	{ 2787, 124928 },
+	{ 2709, 125952 },
+	{ 2633, 126976 },
+	{ 2560, 128000 },
+	{ 2489, 129024 },
+	{ 2420, 130048 }
+};
+
 static int qcom_vadc_scale_hw_calib_volt(
 				const struct vadc_prescale_ratio *prescale,
 				const struct adc5_data *data,
@@ -97,6 +286,10 @@ static int qcom_vadc_scale_hw_calib_therm(
 				const struct vadc_prescale_ratio *prescale,
 				const struct adc5_data *data,
 				u16 adc_code, int *result_mdec);
+static int qcom_vadc7_scale_hw_calib_therm(
+				const struct vadc_prescale_ratio *prescale,
+				const struct adc5_data *data,
+				u16 adc_code, int *result_mdec);
 static int qcom_vadc_scale_hw_smb_temp(
 				const struct vadc_prescale_ratio *prescale,
 				const struct adc5_data *data,
@@ -109,12 +302,20 @@ static int qcom_vadc_scale_hw_calib_die_temp(
 				const struct vadc_prescale_ratio *prescale,
 				const struct adc5_data *data,
 				u16 adc_code, int *result_mdec);
+static int qcom_vadc7_scale_hw_calib_die_temp(
+				const struct vadc_prescale_ratio *prescale,
+				const struct adc5_data *data,
+				u16 adc_code, int *result_mdec);
 
 static struct qcom_adc5_scale_type scale_adc5_fn[] = {
 	[SCALE_HW_CALIB_DEFAULT] = {qcom_vadc_scale_hw_calib_volt},
 	[SCALE_HW_CALIB_THERM_100K_PULLUP] = {qcom_vadc_scale_hw_calib_therm},
 	[SCALE_HW_CALIB_XOTHERM] = {qcom_vadc_scale_hw_calib_therm},
+	[SCALE_HW_CALIB_THERM_100K_PU_PM7] = {
+					qcom_vadc7_scale_hw_calib_therm},
 	[SCALE_HW_CALIB_PMIC_THERM] = {qcom_vadc_scale_hw_calib_die_temp},
+	[SCALE_HW_CALIB_PMIC_THERM_PM7] = {
+					qcom_vadc7_scale_hw_calib_die_temp},
 	[SCALE_HW_CALIB_PM5_CHG_TEMP] = {qcom_vadc_scale_hw_chg5_temp},
 	[SCALE_HW_CALIB_PM5_SMB_TEMP] = {qcom_vadc_scale_hw_smb_temp},
 };
@@ -291,6 +492,32 @@ static int qcom_vadc_scale_code_voltage_factor(u16 adc_code,
 	return (int) voltage;
 }
 
+static int qcom_vadc7_scale_hw_calib_therm(
+				const struct vadc_prescale_ratio *prescale,
+				const struct adc5_data *data,
+				u16 adc_code, int *result_mdec)
+{
+	s64 resistance = adc_code;
+	int ret, result = 0;
+
+	if (adc_code >= RATIO_MAX_ADC7)
+		return -EINVAL;
+
+	/* (ADC code * R_PULLUP (100Kohm)) / (full_scale_code - ADC code)*/
+	resistance *= R_PU_100K;
+	resistance = div64_s64(resistance, RATIO_MAX_ADC7 - adc_code);
+
+	ret = qcom_vadc_map_voltage_temp(adcmap7_100k,
+				 ARRAY_SIZE(adcmap7_100k),
+				 resistance, &result);
+	if (ret)
+		return ret;
+
+	*result_mdec = result;
+
+	return 0;
+}
+
 static int qcom_vadc_scale_hw_calib_volt(
 				const struct vadc_prescale_ratio *prescale,
 				const struct adc5_data *data,
@@ -330,6 +557,37 @@ static int qcom_vadc_scale_hw_calib_die_temp(
 	return 0;
 }
 
+static int qcom_vadc7_scale_hw_calib_die_temp(
+				const struct vadc_prescale_ratio *prescale,
+				const struct adc5_data *data,
+				u16 adc_code, int *result_mdec)
+{
+
+	int voltage, vtemp0, temp, i;
+
+	voltage = qcom_vadc_scale_code_voltage_factor(adc_code,
+				prescale, data, 1);
+
+	for (i = 0; i < ARRAY_SIZE(adcmap7_die_temp); i++)
+		if (adcmap7_die_temp[i].x > voltage)
+			break;
+
+	if (i == 0) {
+		*result_mdec = DIE_TEMP_ADC7_SCALE_1;
+	} else if (i == ARRAY_SIZE(adcmap7_die_temp)) {
+		*result_mdec = DIE_TEMP_ADC7_MAX;
+	} else {
+		vtemp0 = adcmap7_die_temp[i - 1].x;
+		voltage = voltage - vtemp0;
+		temp = div64_s64(voltage * DIE_TEMP_ADC7_SCALE_FACTOR,
+			adcmap7_die_temp[i - 1].y);
+		temp += DIE_TEMP_ADC7_SCALE_1 + (DIE_TEMP_ADC7_SCALE_2 * (i - 1));
+		*result_mdec = temp;
+	}
+
+	return 0;
+}
+
 static int qcom_vadc_scale_hw_smb_temp(
 				const struct vadc_prescale_ratio *prescale,
 				const struct adc5_data *data,
diff --git a/drivers/iio/adc/qcom-vadc-common.h b/drivers/iio/adc/qcom-vadc-common.h
index e074902a..d195e83 100644
--- a/drivers/iio/adc/qcom-vadc-common.h
+++ b/drivers/iio/adc/qcom-vadc-common.h
@@ -49,6 +49,14 @@
 #define ADC5_FULL_SCALE_CODE			0x70e4
 #define ADC5_USR_DATA_CHECK			0x8000
 
+#define R_PU_100K			100000
+#define RATIO_MAX_ADC7		0x4000
+
+#define DIE_TEMP_ADC7_SCALE_1				-60000
+#define DIE_TEMP_ADC7_SCALE_2				20000
+#define DIE_TEMP_ADC7_SCALE_FACTOR			1000
+#define DIE_TEMP_ADC7_MAX				160000
+
 /**
  * struct vadc_map_pt - Map the graph representation for ADC channel
  * @x: Represent the ADC digitized code.
@@ -110,8 +118,12 @@ struct vadc_prescale_ratio {
  *	lookup table. The hardware applies offset/slope to adc code.
  * SCALE_HW_CALIB_XOTHERM: Returns XO thermistor voltage in millidegC using
  *	100k pullup. The hardware applies offset/slope to adc code.
+ * SCALE_HW_CALIB_THERM_100K_PU_PM7: Returns temperature in millidegC using
+ *	lookup table for PMIC7. The hardware applies offset/slope to adc code.
  * SCALE_HW_CALIB_PMIC_THERM: Returns result in milli degree's Centigrade.
  *	The hardware applies offset/slope to adc code.
+ * SCALE_HW_CALIB_PMIC_THERM: Returns result in milli degree's Centigrade.
+ *	The hardware applies offset/slope to adc code. This is for PMIC7.
  * SCALE_HW_CALIB_PM5_CHG_TEMP: Returns result in millidegrees for PMIC5
  *	charger temperature.
  * SCALE_HW_CALIB_PM5_SMB_TEMP: Returns result in millidegrees for PMIC5
@@ -126,7 +138,9 @@ enum vadc_scale_fn_type {
 	SCALE_HW_CALIB_DEFAULT,
 	SCALE_HW_CALIB_THERM_100K_PULLUP,
 	SCALE_HW_CALIB_XOTHERM,
+	SCALE_HW_CALIB_THERM_100K_PU_PM7,
 	SCALE_HW_CALIB_PMIC_THERM,
+	SCALE_HW_CALIB_PMIC_THERM_PM7,
 	SCALE_HW_CALIB_PM5_CHG_TEMP,
 	SCALE_HW_CALIB_PM5_SMB_TEMP,
 	SCALE_HW_CALIB_INVALID,
@@ -136,6 +150,7 @@ struct adc5_data {
 	const u32	full_scale_code_volt;
 	const u32	full_scale_code_cur;
 	const struct adc5_channels *adc_chans;
+	const struct iio_info *info;
 	unsigned int	*decimation;
 	unsigned int	*hw_settle_1;
 	unsigned int	*hw_settle_2;
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

Powered by blists - more mailing lists