linux-kernel - Re: [PATCH v2] mtd: rawnand: denali: add more delays before latching incoming data

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <20200422173600.304c7cf2@xps13>
Date:   Wed, 22 Apr 2020 17:36:00 +0200
From:   Miquel Raynal <miquel.raynal@...tlin.com>
To:     Marek Vasut <marex@...x.de>
Cc:     Masahiro Yamada <yamada.masahiro@...ionext.com>,
        linux-mtd@...ts.infradead.org, Richard Weinberger <richard@....at>,
        Vignesh Raghavendra <vigneshr@...com>,
        linux-kernel@...r.kernel.org
Subject: Re: [PATCH v2] mtd: rawnand: denali: add more delays before
 latching incoming data

Hi Marek,

Marek Vasut <marex@...x.de> wrote on Wed, 22 Apr 2020 17:29:53 +0200:

> On 3/17/20 8:18 AM, Masahiro Yamada wrote:
> > The Denali IP have several registers to specify how many clock cycles
> > should be waited between falling/rising signals. You can improve the
> > NAND access performance by programming these registers with optimized
> > values.
> > 
> > Because struct nand_sdr_timings represents the device requirement
> > in pico seconds, denali_setup_data_interface() computes the register
> > values by dividing the device timings with the clock period.
> > 
> > Marek Vasut reported this driver in the latest kernel does not work
> > on his SOCFPGA board. (The on-board NAND chip is mode 5)
> > 
> > The suspicious parameter is acc_clks, so this commit relaxes it.
> > 
> > The Denali NAND Flash Memory Controller User's Guide describes this
> > register as follows:
> > 
> >   acc_clks
> >     signifies the number of bus interface clk_x clock cycles,
> >     controller should wait from read enable going low to sending
> >     out a strobe of clk_x for capturing of incoming data.
> > 
> > Currently, acc_clks is calculated only based on tREA, the delay on the
> > chip side. This does not include additional delays that come from the
> > data path on the PCB and in the SoC, load capacity of the pins, etc.
> > 
> > This relatively becomes a big factor on faster timing modes like mode 5.
> > 
> > Before supporting the ->setup_data_interface() hook (e.g. Linux 4.12),
> > the Denali driver hacks acc_clks in a couple of ways [1] [2] to support
> > the timing mode 5.
> > 
> > We would not go back to the hard-coded acc_clks, but we need to include
> > this factor into the delay somehow. Let's say the amount of the additional
> > delay is 10000 pico sec.
> > 
> > In the new calculation, acc_clks is determined by timings->tREA_max +
> > data_setup_on_host.
> > 
> > Also, prolong the RE# low period to make sure the data hold is met.
> > 
> > Finally, re-center the data latch timing for extra safety.
> > 
> > [1] https://github.com/torvalds/linux/blob/v4.12/drivers/mtd/nand/denali.c#L276
> > [2] https://github.com/torvalds/linux/blob/v4.12/drivers/mtd/nand/denali.c#L282
> > 
> > Reported-by: Marek Vasut <marex@...x.de>
> > Signed-off-by: Masahiro Yamada <yamada.masahiro@...ionext.com>  
> 
> I tested it on the AV SoCFPGA, this seems to work, so feel free to apply.


Great! Thanks a lot for testing, would you mind sending your Tested-by?

Thanks,
Miquèl