| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Tue, 5 May 2020 19:11:05 +0200
From: Christophe Kerello <christophe.kerello@...com>
To: <miquel.raynal@...tlin.com>, <richard@....at>, <vigneshr@...com>,
<robh+dt@...nel.org>, <mark.rutland@....com>,
<gregkh@...uxfoundation.org>, <boris.brezillon@...labora.com>
CC: <linux-mtd@...ts.infradead.org>, <linux-kernel@...r.kernel.org>,
<linux-stm32@...md-mailman.stormreply.com>,
<devicetree@...r.kernel.org>, <marex@...x.de>,
Christophe Kerello <christophe.kerello@...com>
Subject: [PATCH v3 07/10] dt-bindings: memory-controller: add STM32 FMC2 EBI controller documentation
This patch adds the documentation of the device tree bindings for the STM32
FMC2 EBI controller.
Signed-off-by: Christophe Kerello <christophe.kerello@...com>
---
Changes in v3:
- pattern name has been modified
- vendor properties have been modified
- s/_/-/
- add unit suffix (-ns) on timing properties
.../memory-controllers/st,stm32-fmc2-ebi.yaml | 261 +++++++++++++++++++++
1 file changed, 261 insertions(+)
create mode 100644 Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml
diff --git a/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml
new file mode 100644
index 0000000..3ec57d2
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml
@@ -0,0 +1,261 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/st,stm32-fmc2.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics Flexible Memory Controller 2 (FMC2) Bindings
+
+description: |
+ The FMC2 functional block makes the interface with: synchronous and
+ asynchronous static devices (such as PSNOR, PSRAM or other memory-mapped
+ peripherals) and NAND flash memories.
+ Its main purposes are:
+ - to translate AXI transactions into the appropriate external device
+ protocol
+ - to meet the access time requirements of the external devices
+ All external devices share the addresses, data and control signals with the
+ controller. Each external device is accessed by means of a unique Chip
+ Select. The FMC2 performs only one access at a time to an external device.
+
+maintainers:
+ - Christophe Kerello <christophe.kerello@...com>
+
+properties:
+ compatible:
+ const: st,stm32mp1-fmc2-ebi
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ "#address-cells":
+ const: 2
+
+ "#size-cells":
+ const: 1
+
+ ranges:
+ description: |
+ Reflects the memory layout with four integer values per bank. Format:
+ <bank-number> 0 <address of the bank> <size>
+
+patternProperties:
+ "^.*@[0-4],[a-f0-9]+$":
+ type: object
+
+ properties:
+ reg:
+ description: Bank number, base address and size of the device.
+
+ st,fmc2-ebi-cs-transaction-type:
+ description: |
+ Select one of the transactions type supported
+ 0: Asynchronous mode 1 SRAM/FRAM.
+ 1: Asynchronous mode 1 PSRAM.
+ 2: Asynchronous mode A SRAM/FRAM.
+ 3: Asynchronous mode A PSRAM.
+ 4: Asynchronous mode 2 NOR.
+ 5: Asynchronous mode B NOR.
+ 6: Asynchronous mode C NOR.
+ 7: Asynchronous mode D NOR.
+ 8: Synchronous read synchronous write PSRAM.
+ 9: Synchronous read asynchronous write PSRAM.
+ 10: Synchronous read synchronous write NOR.
+ 11: Synchronous read asynchronous write NOR.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 11
+
+ st,fmc2-ebi-cs-cclk-enable:
+ description: Continuous clock enable (first bank must be configured
+ in synchronous mode). The FMC_CLK is generated continuously
+ during asynchronous and synchronous access. By default, the
+ FMC_CLK is only generated during synchronous access.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,fmc2-ebi-cs-mux-enable:
+ description: Address/Data multiplexed on databus (valid only with
+ NOR and PSRAM transactions type). By default, Address/Data
+ are not multiplexed.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,fmc2-ebi-cs-buswidth:
+ description: Data bus width
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 8, 16 ]
+ default: 16
+
+ st,fmc2-ebi-cs-waitpol-high:
+ description: Wait signal polarity (NWAIT signal active high).
+ By default, NWAIT is active low.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,fmc2-ebi-cs-waitcfg-enable:
+ description: The NWAIT signal indicates wheither the data from the
+ device are valid or if a wait state must be inserted when
+ accessing the device in synchronous mode. By default, the
+ NWAIT signal is active one data cycle before wait state.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,fmc2-ebi-cs-wait-enable:
+ description: The NWAIT signal is enabled (its level is taken into
+ account after the programmed latency period to insert wait
+ states if asserted). By default, the NWAIT signal is
+ disabled.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,fmc2-ebi-cs-asyncwait-enable:
+ description: The NWAIT signal is taken into account during asynchronous
+ transactions. By default, the NWAIT signal is not taken
+ into account during asynchronous transactions.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,fmc2-ebi-cs-cpsize:
+ description: CRAM page size. The controller splits the burst access
+ when the memory page is reached. By default, no burst
+ split when crossing page boundary.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 0, 128, 256, 512, 1024 ]
+ default: 0
+
+ st,fmc2-ebi-cs-byte-lane-setup-ns:
+ description: This property configures the byte lane setup timing
+ defined in nanoseconds from NBLx low to Chip Select NEx
+ low.
+
+ st,fmc2-ebi-cs-address-setup-ns:
+ description: This property defines the duration of the address setup
+ phase in nanoseconds used for asynchronous read/write
+ transactions.
+
+ st,fmc2-ebi-cs-address-hold-ns:
+ description: This property defines the duration of the address hold
+ phase in nanoseconds used for asynchronous multiplexed
+ read/write transactions.
+
+ st,fmc2-ebi-cs-data-setup-ns:
+ description: This property defines the duration of the data setup phase
+ in nanoseconds used for asynchronous read/write
+ transactions.
+
+ st,fmc2-ebi-cs-bus-turnaround-ns:
+ description: This property defines the delay in nanoseconds between the
+ end of current read/write transaction and the next
+ transaction.
+
+ st,fmc2-ebi-cs-data-hold-ns:
+ description: This property defines the duration of the data hold phase
+ in nanoseconds used for asynchronous read/write
+ transactions.
+
+ st,fmc2-ebi-cs-clk-period-ns:
+ description: This property defines the FMC_CLK output signal period in
+ nanoseconds.
+
+ st,fmc2-ebi-cs-data-latency-ns:
+ description: This property defines the data latency before reading or
+ writing the first data in nanoseconds.
+
+ st,fmc2_ebi-cs-write-address-setup-ns:
+ description: This property defines the duration of the address setup
+ phase in nanoseconds used for asynchronous write
+ transactions.
+
+ st,fmc2-ebi-cs-write-address-hold-ns:
+ description: This property defines the duration of the address hold
+ phase in nanoseconds used for asynchronous multiplexed
+ write transactions.
+
+ st,fmc2-ebi-cs-write-data-setup-ns:
+ description: This property defines the duration of the data setup
+ phase in nanoseconds used for asynchronous write
+ transactions.
+
+ st,fmc2-ebi-cs-write-bus-turnaround-ns:
+ description: This property defines the delay between the end of current
+ write transaction and the next transaction in nanoseconds.
+
+ st,fmc2-ebi-cs-write-data-hold-ns:
+ description: This property defines the duration of the data hold phase
+ in nanoseconds used for asynchronous write transactions.
+
+ st,fmc2-ebi-cs-max-low-pulse-ns:
+ description: This property defines the maximum chip select low pulse
+ duration in nanoseconds for synchronous transactions. When
+ this timing reaches 0, the controller splits the current
+ access, toggles NE to allow device refresh and restarts a
+ new access.
+
+ required:
+ - reg
+
+required:
+ - "#address-cells"
+ - "#size-cells"
+ - compatible
+ - reg
+ - clocks
+ - ranges
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/stm32mp1-clks.h>
+ #include <dt-bindings/reset/stm32mp1-resets.h>
+ memory-controller@...02000 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "st,stm32mp1-fmc2-ebi";
+ reg = <0x58002000 0x1000>;
+ clocks = <&rcc FMC_K>;
+ resets = <&rcc FMC_R>;
+
+ ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */
+ <1 0 0x64000000 0x04000000>, /* EBI CS 2 */
+ <2 0 0x68000000 0x04000000>, /* EBI CS 3 */
+ <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */
+ <4 0 0x80000000 0x10000000>; /* NAND */
+
+ psram@0,0 {
+ compatible = "mtd-ram";
+ reg = <0 0x00000000 0x100000>;
+ bank-width = <2>;
+
+ st,fmc2-ebi-cs-transaction-type = <1>;
+ st,fmc2-ebi-cs-address-setup-ns = <60>;
+ st,fmc2-ebi-cs-data-setup-ns = <30>;
+ st,fmc2-ebi-cs-bus-turnaround-ns = <5>;
+ };
+
+ nand-controller@4,0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "st,stm32mp15-fmc2";
+ reg = <4 0x00000000 0x1000>,
+ <4 0x08010000 0x1000>,
+ <4 0x08020000 0x1000>,
+ <4 0x01000000 0x1000>,
+ <4 0x09010000 0x1000>,
+ <4 0x09020000 0x1000>;
+ interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>,
+ <&mdma1 20 0x2 0x12000a08 0x0 0x0>,
+ <&mdma1 21 0x2 0x12000a0a 0x0 0x0>;
+ dma-names = "tx", "rx", "ecc";
+
+ nand@0 {
+ reg = <0>;
+ nand-on-flash-bbt;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+ };
+ };
+
+...
--
1.9.1
Powered by blists - more mailing lists