[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <20200511210134.1224532-12-lkundrak@v3.sk>
Date: Mon, 11 May 2020 23:01:34 +0200
From: Lubomir Rintel <lkundrak@...sk>
To: Liam Girdwood <lgirdwood@...il.com>
Cc: Mark Brown <broonie@...nel.org>,
Michael Turquette <mturquette@...libre.com>,
Stephen Boyd <sboyd@...nel.org>,
Rob Herring <robh+dt@...nel.org>, linux-clk@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
linux-media@...r.kernel.org, Lubomir Rintel <lkundrak@...sk>
Subject: [PATCH 11/11] ASoC: mmp-sspa: Add Device Tree support
This makes it possible to select CONFIG_SND_MMP_SOC_SSPA directly, as
opposed to via CONFIG_SND_MMP_SOC, and for the driver to bind to a device
tree node. That makes the driver useful on Device Tree based systems,
with audio-graph-card or simple-card.
The aforementioned card drivers control the master clock themselves and
don't call the set_dai_sysclk() or set_dai_pll(), thus the respective
handlers don't serve any purpose anymore. Instead, they return early and
the hw_params() handler sets the appropriate bitclk itself.
The register range is split into two -- for the RX block and for the TX
block. On a MMP2 there are two pairs of them; the first one has the
clock controller in the middle, while the second just has a hole:
0xd42a0c00 - 0xd42a0c30 RX1
0xd42a0c30 - 0xd42a0c40 Clocks
0xd42a0c80 - 0xd42a0cb0 TX1
0xd42a0d00 - 0xd42a0d30 RX2
0xd42a0d80 - 0xd42a0cb0 TX2
For this reason, mmp_sspa_write_reg() and mmp_sspa_read_reg() are
replaced with direct calls to I/O routines.
Tested on a MMP2-based OLPC XO-1.75 laptop with rt5631 coded, mmp_tdma DMA
engine and MMP2 clock controller glued together with audio-graph-card.
Signed-off-by: Lubomir Rintel <lkundrak@...sk>
---
sound/soc/pxa/Kconfig | 20 +++---
sound/soc/pxa/mmp-sspa.c | 139 ++++++++++++++++++++++++++-------------
sound/soc/pxa/mmp-sspa.h | 28 +++-----
3 files changed, 113 insertions(+), 74 deletions(-)
diff --git a/sound/soc/pxa/Kconfig b/sound/soc/pxa/Kconfig
index d4c0f580a565..7ad2fd7e653b 100644
--- a/sound/soc/pxa/Kconfig
+++ b/sound/soc/pxa/Kconfig
@@ -9,14 +9,8 @@ config SND_PXA2XX_SOC
to select the audio interfaces to support below.
config SND_MMP_SOC
- bool "Soc Audio for Marvell MMP chips"
- depends on ARCH_MMP
+ bool
select MMP_SRAM
- select SND_SOC_GENERIC_DMAENGINE_PCM
- select SND_ARM
- help
- Say Y if you want to add support for codecs attached to
- the MMP SSPA interface.
config SND_PXA2XX_AC97
tristate
@@ -39,7 +33,13 @@ config SND_PXA_SOC_SSP
select SND_PXA2XX_LIB
config SND_MMP_SOC_SSPA
- tristate
+ tristate "SoC Audio via MMP SSPA ports"
+ depends on ARCH_MMP
+ select SND_SOC_GENERIC_DMAENGINE_PCM
+ select SND_ARM
+ help
+ Say Y if you want to add support for codecs attached to
+ the MMP SSPA interface.
config SND_PXA2XX_SOC_CORGI
tristate "SoC Audio support for Sharp Zaurus SL-C7x0"
@@ -232,8 +232,8 @@ config SND_PXA2XX_SOC_IMOTE2
config SND_MMP_SOC_BROWNSTONE
tristate "SoC Audio support for Marvell Brownstone"
- depends on SND_MMP_SOC && MACH_BROWNSTONE && I2C
- select SND_MMP_SOC_SSPA
+ depends on SND_MMP_SOC_SSPA && MACH_BROWNSTONE && I2C
+ select SND_MMP_SOC
select MFD_WM8994
select SND_SOC_WM8994
help
diff --git a/sound/soc/pxa/mmp-sspa.c b/sound/soc/pxa/mmp-sspa.c
index 86277471974a..b0accd49c89d 100644
--- a/sound/soc/pxa/mmp-sspa.c
+++ b/sound/soc/pxa/mmp-sspa.c
@@ -28,27 +28,20 @@
* SSPA audio private data
*/
struct sspa_priv {
- void __iomem *mmio_base;
+ void __iomem *tx_base;
+ void __iomem *rx_base;
+
struct snd_dmaengine_dai_dma_data playback_dma_data;
struct snd_dmaengine_dai_dma_data capture_dma_data;
struct clk *clk;
struct clk *audio_clk;
struct clk *sysclk;
+
int running_cnt;
u32 sp;
u32 ctrl;
};
-static void mmp_sspa_write_reg(struct sspa_priv *sspa, u32 reg, u32 val)
-{
- __raw_writel(val, sspa->mmio_base + reg);
-}
-
-static u32 mmp_sspa_read_reg(struct sspa_priv *sspa, u32 reg)
-{
- return __raw_readl(sspa->mmio_base + reg);
-}
-
static void mmp_sspa_tx_enable(struct sspa_priv *sspa)
{
unsigned int sspa_sp = sspa->sp;
@@ -56,7 +49,7 @@ static void mmp_sspa_tx_enable(struct sspa_priv *sspa)
sspa_sp &= ~SSPA_SP_MSL;
sspa_sp |= SSPA_SP_S_EN;
sspa_sp |= SSPA_SP_WEN;
- mmp_sspa_write_reg(sspa, SSPA_TXSP, sspa_sp);
+ __raw_writel(sspa_sp, sspa->tx_base + SSPA_SP);
}
static void mmp_sspa_tx_disable(struct sspa_priv *sspa)
@@ -66,7 +59,7 @@ static void mmp_sspa_tx_disable(struct sspa_priv *sspa)
sspa_sp &= ~SSPA_SP_MSL;
sspa_sp &= ~SSPA_SP_S_EN;
sspa_sp |= SSPA_SP_WEN;
- mmp_sspa_write_reg(sspa, SSPA_TXSP, sspa_sp);
+ __raw_writel(sspa_sp, sspa->tx_base + SSPA_SP);
}
static void mmp_sspa_rx_enable(struct sspa_priv *sspa)
@@ -75,7 +68,7 @@ static void mmp_sspa_rx_enable(struct sspa_priv *sspa)
sspa_sp |= SSPA_SP_S_EN;
sspa_sp |= SSPA_SP_WEN;
- mmp_sspa_write_reg(sspa, SSPA_RXSP, sspa_sp);
+ __raw_writel(sspa_sp, sspa->rx_base + SSPA_SP);
}
static void mmp_sspa_rx_disable(struct sspa_priv *sspa)
@@ -84,7 +77,7 @@ static void mmp_sspa_rx_disable(struct sspa_priv *sspa)
sspa_sp &= ~SSPA_SP_S_EN;
sspa_sp |= SSPA_SP_WEN;
- mmp_sspa_write_reg(sspa, SSPA_RXSP, sspa_sp);
+ __raw_writel(sspa_sp, sspa->rx_base + SSPA_SP);
}
static int mmp_sspa_startup(struct snd_pcm_substream *substream,
@@ -105,7 +98,6 @@ static void mmp_sspa_shutdown(struct snd_pcm_substream *substream,
clk_disable_unprepare(sspa->clk);
clk_disable_unprepare(sspa->sysclk);
-
}
/*
@@ -115,8 +107,12 @@ static int mmp_sspa_set_dai_sysclk(struct snd_soc_dai *cpu_dai,
int clk_id, unsigned int freq, int dir)
{
struct sspa_priv *sspa = snd_soc_dai_get_drvdata(cpu_dai);
+ struct device *dev = cpu_dai->component->dev;
int ret = 0;
+ if (dev->of_node)
+ return -ENOTSUPP;
+
switch (clk_id) {
case MMP_SSPA_CLK_AUDIO:
ret = clk_set_rate(sspa->audio_clk, freq);
@@ -139,8 +135,12 @@ static int mmp_sspa_set_dai_pll(struct snd_soc_dai *cpu_dai, int pll_id,
unsigned int freq_out)
{
struct sspa_priv *sspa = snd_soc_dai_get_drvdata(cpu_dai);
+ struct device *dev = cpu_dai->component->dev;
int ret = 0;
+ if (dev->of_node)
+ return -ENOTSUPP;
+
switch (pll_id) {
case MMP_SYSCLK:
ret = clk_set_rate(sspa->sysclk, freq_out);
@@ -213,6 +213,7 @@ static int mmp_sspa_hw_params(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
struct sspa_priv *sspa = snd_soc_dai_get_drvdata(dai);
+ struct device *dev = dai->component->dev;
u32 sspa_ctrl = sspa->ctrl;
int bits;
int bitval;
@@ -238,7 +239,7 @@ static int mmp_sspa_hw_params(struct snd_pcm_substream *substream,
return -EINVAL;
}
- if (params_channels(params) == 2)
+ if (dev->of_node || params_channels(params) == 2)
sspa_ctrl |= SSPA_CTL_XPH;
sspa_ctrl &= ~SSPA_CTL_XWDLEN1_MASK;
@@ -256,12 +257,17 @@ static int mmp_sspa_hw_params(struct snd_pcm_substream *substream,
sspa->sp &= ~SSPA_TXSP_FPER_MASK;
sspa->sp |= SSPA_TXSP_FPER(bits * 2 - 1);
+ if (dev->of_node) {
+ clk_set_rate(sspa->clk, params_rate(params) *
+ params_channels(params) * bits);
+ }
+
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
- mmp_sspa_write_reg(sspa, SSPA_TXCTL, sspa_ctrl);
- mmp_sspa_write_reg(sspa, SSPA_TXFIFO_LL, 0x1);
+ __raw_writel(sspa_ctrl, sspa->tx_base + SSPA_CTL);
+ __raw_writel(0x1, sspa->tx_base + SSPA_FIFO_UL);
} else {
- mmp_sspa_write_reg(sspa, SSPA_RXCTL, sspa_ctrl);
- mmp_sspa_write_reg(sspa, SSPA_RXFIFO_UL, 0x0);
+ __raw_writel(sspa_ctrl, sspa->rx_base + SSPA_CTL);
+ __raw_writel(0x0, sspa->rx_base + SSPA_FIFO_UL);
}
return 0;
@@ -410,19 +416,19 @@ static int mmp_sspa_open(struct snd_soc_component *component,
pm_runtime_get_sync(component->dev);
/* we can only change the settings if the port is not in use */
- if ((mmp_sspa_read_reg(sspa, SSPA_TXSP) & SSPA_SP_S_EN) ||
- (mmp_sspa_read_reg(sspa, SSPA_RXSP) & SSPA_SP_S_EN)) {
+ if ((__raw_readl(sspa->tx_base + SSPA_SP) & SSPA_SP_S_EN) ||
+ (__raw_readl(sspa->rx_base + SSPA_SP) & SSPA_SP_S_EN)) {
dev_err(component->dev,
"can't change hardware dai format: stream is in use\n");
return -EBUSY;
}
- mmp_sspa_write_reg(sspa, SSPA_TXSP, sspa->sp);
- mmp_sspa_write_reg(sspa, SSPA_RXSP, sspa->sp);
+ __raw_writel(sspa->sp, sspa->tx_base + SSPA_SP);
+ __raw_writel(sspa->sp, sspa->rx_base + SSPA_SP);
sspa->sp &= ~(SSPA_SP_S_RST | SSPA_SP_FFLUSH);
- mmp_sspa_write_reg(sspa, SSPA_TXSP, sspa->sp);
- mmp_sspa_write_reg(sspa, SSPA_RXSP, sspa->sp);
+ __raw_writel(sspa->sp, sspa->tx_base + SSPA_SP);
+ __raw_writel(sspa->sp, sspa->rx_base + SSPA_SP);
/*
* FIXME: hw issue, for the tx serial port,
@@ -431,10 +437,10 @@ static int mmp_sspa_open(struct snd_soc_component *component,
* The master/slave mode has been set in the
* rx port.
*/
- mmp_sspa_write_reg(sspa, SSPA_TXSP, sspa->sp & ~SSPA_SP_MSL);
+ __raw_writel(sspa->sp & ~SSPA_SP_MSL, sspa->tx_base + SSPA_SP);
- mmp_sspa_write_reg(sspa, SSPA_TXCTL, sspa->ctrl);
- mmp_sspa_write_reg(sspa, SSPA_RXCTL, sspa->ctrl);
+ __raw_writel(sspa->ctrl, sspa->tx_base + SSPA_CTL);
+ __raw_writel(sspa->ctrl, sspa->rx_base + SSPA_CTL);
return 0;
}
@@ -462,22 +468,51 @@ static int asoc_mmp_sspa_probe(struct platform_device *pdev)
if (!sspa)
return -ENOMEM;
- sspa->mmio_base = devm_platform_ioremap_resource(pdev, 0);
- if (IS_ERR(sspa->mmio_base))
- return PTR_ERR(sspa->mmio_base);
+ if (pdev->dev.of_node) {
+ sspa->rx_base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(sspa->rx_base))
+ return PTR_ERR(sspa->rx_base);
- sspa->clk = devm_clk_get(&pdev->dev, NULL);
- if (IS_ERR(sspa->clk))
- return PTR_ERR(sspa->clk);
+ sspa->tx_base = devm_platform_ioremap_resource(pdev, 1);
+ if (IS_ERR(sspa->tx_base))
+ return PTR_ERR(sspa->tx_base);
- sspa->audio_clk = clk_get(NULL, "mmp-audio");
- if (IS_ERR(sspa->audio_clk))
- return PTR_ERR(sspa->audio_clk);
+ sspa->clk = devm_clk_get(&pdev->dev, "bitclk");
+ if (IS_ERR(sspa->clk))
+ return PTR_ERR(sspa->clk);
- sspa->sysclk = clk_get(NULL, "mmp-sysclk");
- if (IS_ERR(sspa->sysclk)) {
- clk_put(sspa->audio_clk);
- return PTR_ERR(sspa->sysclk);
+ sspa->audio_clk = devm_clk_get(&pdev->dev, "audio");
+ if (IS_ERR(sspa->audio_clk))
+ return PTR_ERR(sspa->audio_clk);
+ } else {
+ struct resource *res;
+
+ res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+ if (res == NULL)
+ return -ENODEV;
+
+ sspa->rx_base = devm_ioremap(&pdev->dev, res->start, 0x30);
+ if (IS_ERR(sspa->rx_base))
+ return PTR_ERR(sspa->rx_base);
+
+ sspa->tx_base = devm_ioremap(&pdev->dev,
+ res->start + 0x80, 0x30);
+ if (IS_ERR(sspa->tx_base))
+ return PTR_ERR(sspa->tx_base);
+
+ sspa->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(sspa->clk))
+ return PTR_ERR(sspa->clk);
+
+ sspa->audio_clk = clk_get(NULL, "mmp-audio");
+ if (IS_ERR(sspa->audio_clk))
+ return PTR_ERR(sspa->audio_clk);
+
+ sspa->sysclk = clk_get(NULL, "mmp-sysclk");
+ if (IS_ERR(sspa->sysclk)) {
+ clk_put(sspa->audio_clk);
+ return PTR_ERR(sspa->sysclk);
+ }
}
pm_runtime_enable(&pdev->dev);
clk_prepare_enable(sspa->audio_clk);
@@ -486,8 +521,8 @@ static int asoc_mmp_sspa_probe(struct platform_device *pdev)
sspa->playback_dma_data.maxburst = 4;
sspa->capture_dma_data.maxburst = 4;
/* You know, these addresses are actually ignored. */
- sspa->playback_dma_data.addr = SSPA_TXD;
- sspa->capture_dma_data.addr = SSPA_RXD;
+ sspa->capture_dma_data.addr = SSPA_D;
+ sspa->playback_dma_data.addr = 0x80 + SSPA_D;
if (pdev->dev.of_node) {
int ret;
@@ -508,14 +543,28 @@ static int asoc_mmp_sspa_remove(struct platform_device *pdev)
clk_disable_unprepare(sspa->audio_clk);
pm_runtime_disable(&pdev->dev);
+
+ if (pdev->dev.of_node)
+ return 0;
+
clk_put(sspa->audio_clk);
clk_put(sspa->sysclk);
return 0;
}
+#ifdef CONFIG_OF
+static const struct of_device_id mmp_sspa_of_match[] = {
+ { .compatible = "marvell,mmp-sspa" },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, mmp_sspa_of_match);
+#endif
+
static struct platform_driver asoc_mmp_sspa_driver = {
.driver = {
.name = "mmp-sspa-dai",
+ .of_match_table = of_match_ptr(mmp_sspa_of_match),
},
.probe = asoc_mmp_sspa_probe,
.remove = asoc_mmp_sspa_remove,
diff --git a/sound/soc/pxa/mmp-sspa.h b/sound/soc/pxa/mmp-sspa.h
index 328969b57ad1..938ef2f667e3 100644
--- a/sound/soc/pxa/mmp-sspa.h
+++ b/sound/soc/pxa/mmp-sspa.h
@@ -10,25 +10,15 @@
/*
* SSPA Registers
*/
-#define SSPA_RXD (0x00)
-#define SSPA_RXID (0x04)
-#define SSPA_RXCTL (0x08)
-#define SSPA_RXSP (0x0c)
-#define SSPA_RXFIFO_UL (0x10)
-#define SSPA_RXINT_MASK (0x14)
-#define SSPA_RXC (0x18)
-#define SSPA_RXFIFO_NOFS (0x1c)
-#define SSPA_RXFIFO_SIZE (0x20)
-
-#define SSPA_TXD (0x80)
-#define SSPA_TXID (0x84)
-#define SSPA_TXCTL (0x88)
-#define SSPA_TXSP (0x8c)
-#define SSPA_TXFIFO_LL (0x90)
-#define SSPA_TXINT_MASK (0x94)
-#define SSPA_TXC (0x98)
-#define SSPA_TXFIFO_NOFS (0x9c)
-#define SSPA_TXFIFO_SIZE (0xa0)
+#define SSPA_D (0x00)
+#define SSPA_ID (0x04)
+#define SSPA_CTL (0x08)
+#define SSPA_SP (0x0c)
+#define SSPA_FIFO_UL (0x10)
+#define SSPA_INT_MASK (0x14)
+#define SSPA_C (0x18)
+#define SSPA_FIFO_NOFS (0x1c)
+#define SSPA_FIFO_SIZE (0x20)
/* SSPA Control Register */
#define SSPA_CTL_XPH (1 << 31) /* Read Phase */
--
2.26.2
Powered by blists - more mailing lists