| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20200512151947.120348-2-vishal.sagar@xilinx.com>
Date: Tue, 12 May 2020 20:49:46 +0530
From: Vishal Sagar <vishal.sagar@...inx.com>
To: Hyun Kwon <hyunk@...inx.com>, laurent.pinchart@...asonboard.com,
mchehab@...nel.org, robh+dt@...nel.org, mark.rutland@....com,
Michal Simek <michals@...inx.com>, linux-media@...r.kernel.org,
devicetree@...r.kernel.org, hans.verkuil@...co.com,
linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
Dinesh Kumar <dineshk@...inx.com>,
Sandip Kothari <sandipk@...inx.com>,
Luca Ceresoli <luca@...aceresoli.net>,
Jacopo Mondi <jacopo@...ndi.org>
Cc: Vishal Sagar <vishal.sagar@...inx.com>,
Hyun Kwon <hyun.kwon@...inx.com>, Rob Herring <robh@...nel.org>
Subject: [PATCH v13 1/2] media: dt-bindings: media: xilinx: Add Xilinx MIPI CSI-2 Rx Subsystem
Add bindings documentation for Xilinx MIPI CSI-2 Rx Subsystem.
The Xilinx MIPI CSI-2 Rx Subsystem consists of a CSI-2 Rx controller, a
D-PHY in Rx mode and a Video Format Bridge.
Signed-off-by: Vishal Sagar <vishal.sagar@...inx.com>
Reviewed-by: Hyun Kwon <hyun.kwon@...inx.com>
Reviewed-by: Rob Herring <robh@...nel.org>
Reviewed-by: Luca Ceresoli <luca@...aceresoli.net>
Reviewed-by: Laurent Pinchart <laurent.pinchart@...asonboard.com>
---
v13
- Based on Laurent's suggestions
- Fixed the datatypes values as minimum and maximum
- condition added for en-vcx property
v12
- Moved to yaml format
- Update CSI-2 and D-PHY
- Mention that bindings for D-PHY not here
- reset -> video-reset
v11
- Modify compatible string from 4.0 to 5.0
v10
- No changes
v9
- Fix xlnx,vfb description.
- s/Optional/Required endpoint property.
- Move data-lanes description from Ports to endpoint property section.
v8
- Added reset-gpios optional property to assert video_aresetn
v7
- Removed the control name from dt bindings
- Updated the example dt node name to csi2rx
v6
- Added "control" after V4L2_CID_XILINX_MIPICSISS_ACT_LANES as suggested by Luca
- Added reviewed by Rob Herring
v5
- Incorporated comments by Luca Cersoli
- Removed DPHY clock from description and example
- Removed bayer pattern from device tree MIPI CSI IP
doesn't deal with bayer pattern.
v4
- Added reviewed by Hyun Kwon
v3
- removed interrupt parent as suggested by Rob
- removed dphy clock
- moved vfb to optional properties
- Added required and optional port properties section
- Added endpoint property section
v2
- updated the compatible string to latest version supported
- removed DPHY related parameters
- added CSI v2.0 related property (including VCX for supporting upto 16
virtual channels).
- modified csi-pxl-format from string to unsigned int type where the value
is as per the CSI specification
- Defined port 0 and port 1 as sink and source ports.
- Removed max-lanes property as suggested by Rob and Sakari
.../bindings/media/xilinx/xlnx,csi2rxss.yaml | 226 ++++++++++++++++++
1 file changed, 226 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml
diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml b/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml
new file mode 100644
index 000000000000..b0885f461785
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml
@@ -0,0 +1,226 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/xilinx/xlnx,csi2rxss.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx MIPI CSI-2 Receiver Subsystem
+
+maintainers:
+ - Vishal Sagar <vishal.sagar@...inx.com>
+
+description: |
+ The Xilinx MIPI CSI-2 Receiver Subsystem is used to capture MIPI CSI-2
+ traffic from compliant camera sensors and send the output as AXI4 Stream
+ video data for image processing.
+ The subsystem consists of a MIPI D-PHY in slave mode which captures the
+ data packets. This is passed along the MIPI CSI-2 Rx IP which extracts the
+ packet data. The optional Video Format Bridge (VFB) converts this data to
+ AXI4 Stream video data.
+ For more details, please refer to PG232 Xilinx MIPI CSI-2 Receiver Subsystem.
+ Please note that this bindings includes only the MIPI CSI-2 Rx controller
+ and Video Format Bridge and not D-PHY.
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - xlnx,mipi-csi2-rx-subsystem-5.0
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ description: List of clock specifiers
+ items:
+ - description: AXI Lite clock
+ - description: Video clock
+
+ clock-names:
+ items:
+ - const: lite_aclk
+ - const: video_aclk
+
+ xlnx,csi-pxl-format:
+ description: |
+ This denotes the CSI Data type selected in hw design.
+ Packets other than this data type (except for RAW8 and
+ User defined data types) will be filtered out.
+ Possible values are as below -
+ 0x1e - YUV4228B
+ 0x1f - YUV42210B
+ 0x20 - RGB444
+ 0x21 - RGB555
+ 0x22 - RGB565
+ 0x23 - RGB666
+ 0x24 - RGB888
+ 0x28 - RAW6
+ 0x29 - RAW7
+ 0x2a - RAW8
+ 0x2b - RAW10
+ 0x2c - RAW12
+ 0x2d - RAW14
+ 0x2e - RAW16
+ 0x2f - RAW20
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - anyOf:
+ - minimum: 0x1e
+ - maximum: 0x24
+ - minimum: 0x28
+ - maximum: 0x2f
+
+ xlnx,vfb:
+ type: boolean
+ description: Present when Video Format Bridge is enabled in IP configuration
+
+ xlnx,en-csi-v2-0:
+ type: boolean
+ description: Present if CSI v2 is enabled in IP configuration.
+
+ xlnx,en-vcx:
+ type: boolean
+ description: |
+ When present, there are maximum 16 virtual channels, else only 4.
+
+ xlnx,en-active-lanes:
+ type: boolean
+ description: |
+ Present if the number of active lanes can be re-configured at
+ runtime in the Protocol Configuration Register. Otherwise all lanes,
+ as set in IP configuration, are always active.
+
+ video-reset-gpios:
+ description: Optional specifier for a GPIO that asserts video_aresetn.
+ maxItems: 1
+
+ ports:
+ type: object
+
+ properties:
+ port@0:
+ type: object
+ description: |
+ Input / sink port node, single endpoint describing the
+ CSI-2 transmitter.
+
+ properties:
+ reg:
+ const: 0
+
+ endpoint:
+ type: object
+
+ properties:
+
+ data-lanes:
+ description: |
+ This is required only in the sink port 0 endpoint which
+ connects to MIPI CSI-2 source like sensor.
+ The possible values are -
+ 1 - For 1 lane enabled in IP.
+ 1 2 - For 2 lanes enabled in IP.
+ 1 2 3 - For 3 lanes enabled in IP.
+ 1 2 3 4 - For 4 lanes enabled in IP.
+ items:
+ - const: 1
+ - const: 2
+ - const: 3
+ - const: 4
+
+ remote-endpoint: true
+
+ required:
+ - data-lanes
+ - remote-endpoint
+
+ additionalProperties: false
+
+ additionalProperties: false
+
+ port@1:
+ type: object
+ description: |
+ Output / source port node, endpoint describing modules
+ connected the CSI-2 receiver.
+
+ properties:
+
+ reg:
+ const: 1
+
+ endpoint:
+ type: object
+
+ properties:
+
+ remote-endpoint: true
+
+ required:
+ - remote-endpoint
+
+ additionalProperties: false
+
+ additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-names
+ - xlnx,csi-pxl-format
+ - ports
+
+if:
+ not:
+ required:
+ - xlnx,en-csi-v2-0
+then:
+ properties:
+ xlnx,en-vcx: false
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ xcsi2rxss_1: csi2rx@...20000 {
+ compatible = "xlnx,mipi-csi2-rx-subsystem-5.0";
+ reg = <0x0 0xa0020000 0x0 0x10000>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 95 4>;
+ xlnx,csi-pxl-format = <0x2a>;
+ xlnx,vfb;
+ xlnx,en-active-lanes;
+ xlnx,en-csi-v2-0;
+ xlnx,en-vcx;
+ clock-names = "lite_aclk", "video_aclk";
+ clocks = <&misc_clk_0>, <&misc_clk_1>;
+ video-reset-gpios = <&gpio 86 GPIO_ACTIVE_LOW>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ /* Sink port */
+ reg = <0>;
+ csiss_in: endpoint {
+ data-lanes = <1 2 3 4>;
+ /* MIPI CSI-2 Camera handle */
+ remote-endpoint = <&camera_out>;
+ };
+ };
+ port@1 {
+ /* Source port */
+ reg = <1>;
+ csiss_out: endpoint {
+ remote-endpoint = <&vproc_in>;
+ };
+ };
+ };
+ };
--
2.21.0
Powered by blists - more mailing lists