| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAL_JsqJ1Om2CX5e1y32bzeiuv4fAdyFpZ88a346g4Q+jq_Ldcg@mail.gmail.com>
Date: Tue, 19 May 2020 11:11:43 -0600
From: Rob Herring <robh+dt@...nel.org>
To: Kishon Vijay Abraham I <kishon@...com>
Cc: Bjorn Helgaas <bhelgaas@...gle.com>,
Lorenzo Pieralisi <lorenzo.pieralisi@....com>,
Robin Murphy <robin.murphy@....com>,
Tom Joseph <tjoseph@...ence.com>,
PCI <linux-pci@...r.kernel.org>, devicetree@...r.kernel.org,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
"moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE"
<linux-arm-kernel@...ts.infradead.org>
Subject: Re: [PATCH v3 4/4] PCI: cadence: Use "dma-ranges" instead of
"cdns,no-bar-match-nbits" property
On Fri, May 8, 2020 at 7:07 AM Kishon Vijay Abraham I <kishon@...com> wrote:
>
> Cadence PCIe core driver (host mode) uses "cdns,no-bar-match-nbits"
> property to configure the number of bits passed through from PCIe
> address to internal address in Inbound Address Translation register.
> This only used the NO MATCH BAR.
>
> However standard PCI dt-binding already defines "dma-ranges" to
> describe the address ranges accessible by PCIe controller. Add support
> in Cadence PCIe host driver to parse dma-ranges and configure the
> inbound regions for BAR0, BAR1 and NO MATCH BAR. Cadence IP specifies
> maximum size for BAR0 as 256GB, maximum size for BAR1 as 2 GB, so if
> the dma-ranges specifies a size larger than the maximum allowed, the
> driver will split and configure the BARs.
Would be useful to know what your dma-ranges contains now.
> Legacy device tree binding compatibility is maintained by retaining
> support for "cdns,no-bar-match-nbits".
>
> Signed-off-by: Kishon Vijay Abraham I <kishon@...com>
> ---
> .../controller/cadence/pcie-cadence-host.c | 141 ++++++++++++++++--
> drivers/pci/controller/cadence/pcie-cadence.h | 17 ++-
> 2 files changed, 141 insertions(+), 17 deletions(-)
>
> diff --git a/drivers/pci/controller/cadence/pcie-cadence-host.c b/drivers/pci/controller/cadence/pcie-cadence-host.c
> index 6ecebb79057a..2485ecd8434d 100644
> --- a/drivers/pci/controller/cadence/pcie-cadence-host.c
> +++ b/drivers/pci/controller/cadence/pcie-cadence-host.c
> @@ -11,6 +11,12 @@
>
> #include "pcie-cadence.h"
>
> +static u64 cdns_rp_bar_max_size[] = {
> + [RP_BAR0] = _ULL(128 * SZ_2G),
> + [RP_BAR1] = SZ_2G,
> + [RP_NO_BAR] = SZ_64T,
> +};
> +
> void __iomem *cdns_pci_map_bus(struct pci_bus *bus, unsigned int devfn,
> int where)
> {
> @@ -106,6 +112,117 @@ static int cdns_pcie_host_init_root_port(struct cdns_pcie_rc *rc)
> return 0;
> }
>
> +static void cdns_pcie_host_bar_ib_config(struct cdns_pcie_rc *rc,
> + enum cdns_pcie_rp_bar bar,
> + u64 cpu_addr, u32 aperture)
> +{
> + struct cdns_pcie *pcie = &rc->pcie;
> + u32 addr0, addr1;
> +
> + addr0 = CDNS_PCIE_AT_IB_RP_BAR_ADDR0_NBITS(aperture) |
> + (lower_32_bits(cpu_addr) & GENMASK(31, 8));
> + addr1 = upper_32_bits(cpu_addr);
> + cdns_pcie_writel(pcie, CDNS_PCIE_AT_IB_RP_BAR_ADDR0(bar), addr0);
> + cdns_pcie_writel(pcie, CDNS_PCIE_AT_IB_RP_BAR_ADDR1(bar), addr1);
> +}
> +
> +static int cdns_pcie_host_bar_config(struct cdns_pcie_rc *rc,
> + struct resource_entry *entry,
> + enum cdns_pcie_rp_bar *index)
> +{
> + u64 cpu_addr, pci_addr, size, winsize;
> + struct cdns_pcie *pcie = &rc->pcie;
> + struct device *dev = pcie->dev;
> + enum cdns_pcie_rp_bar bar;
> + unsigned long flags;
> + u32 aperture;
> + u32 value;
> +
> + cpu_addr = entry->res->start;
> + flags = entry->res->flags;
> + pci_addr = entry->res->start - entry->offset;
> + size = resource_size(entry->res);
> + bar = *index;
> +
> + if (entry->offset) {
> + dev_err(dev, "Cannot map PCI addr: %llx to CPU addr: %llx\n",
> + pci_addr, cpu_addr);
Would be a bit more clear to say PCI addr must equal CPU addr.
> + return -EINVAL;
> + }
> +
> + value = cdns_pcie_readl(pcie, CDNS_PCIE_LM_RC_BAR_CFG);
> + while (size > 0) {
> + if (bar > RP_NO_BAR) {
> + dev_err(dev, "Failed to map inbound regions!\n");
> + return -EINVAL;
> + }
> +
> + winsize = size;
> + if (size > cdns_rp_bar_max_size[bar])
> + winsize = cdns_rp_bar_max_size[bar];
> +
> + aperture = ilog2(winsize);
> +
> + cdns_pcie_host_bar_ib_config(rc, bar, cpu_addr, aperture);
> +
> + if (bar == RP_NO_BAR)
> + break;
> +
> + if (winsize + cpu_addr >= SZ_4G) {
> + if (!(flags & IORESOURCE_PREFETCH))
> + value |= LM_RC_BAR_CFG_CTRL_MEM_64BITS(bar);
> + value |= LM_RC_BAR_CFG_CTRL_PREF_MEM_64BITS(bar);
> + } else {
> + if (!(flags & IORESOURCE_PREFETCH))
> + value |= LM_RC_BAR_CFG_CTRL_MEM_32BITS(bar);
> + value |= LM_RC_BAR_CFG_CTRL_PREF_MEM_32BITS(bar);
> + }
> +
> + value |= LM_RC_BAR_CFG_APERTURE(bar, aperture);
> +
> + size -= winsize;
> + cpu_addr += winsize;
> + bar++;
> + }
> + cdns_pcie_writel(pcie, CDNS_PCIE_LM_RC_BAR_CFG, value);
> + *index = bar;
> +
> + return 0;
> +}
> +
> +static int cdns_pcie_host_map_dma_ranges(struct cdns_pcie_rc *rc)
> +{
> + enum cdns_pcie_rp_bar bar = RP_BAR0;
> + struct cdns_pcie *pcie = &rc->pcie;
> + struct device *dev = pcie->dev;
> + struct device_node *np = dev->of_node;
> + struct pci_host_bridge *bridge;
> + struct resource_entry *entry;
> + u32 no_bar_nbits = 32;
> + int err;
> +
> + bridge = pci_host_bridge_from_priv(rc);
> + if (!bridge)
> + return -ENOMEM;
> +
> + if (list_empty(&bridge->dma_ranges)) {
> + of_property_read_u32(np, "cdns,no-bar-match-nbits",
> + &no_bar_nbits);
> + cdns_pcie_host_bar_ib_config(rc, RP_NO_BAR, 0x0, no_bar_nbits);
> + return 0;
> + }
> +
> + resource_list_for_each_entry(entry, &bridge->dma_ranges) {
> + err = cdns_pcie_host_bar_config(rc, entry, &bar);
Seems like this should have some better logic to pick which BAR to
use. Something like find the biggest region and then find the smallest
BAR that it fits in. Then get the next biggest...
> + if (err) {
> + dev_err(dev, "Fail to configure IB using dma-ranges\n");
> + return err;
> + }
> + }
> +
> + return 0;
> +}
> +
Powered by blists - more mailing lists