[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <20200526183931.358395909@linuxfoundation.org>
Date: Tue, 26 May 2020 20:53:28 +0200
From: Greg Kroah-Hartman <gregkh@...uxfoundation.org>
To: linux-kernel@...r.kernel.org
Cc: Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
stable@...r.kernel.org, Dragos Bogdan <dragos.bogdan@...log.com>,
Alexandru Ardelean <alexandru.ardelean@...log.com>,
Stable@...r.kernel.org,
Jonathan Cameron <Jonathan.Cameron@...wei.com>
Subject: [PATCH 4.9 59/64] staging: iio: ad2s1210: Fix SPI reading
From: Dragos Bogdan <dragos.bogdan@...log.com>
commit 5e4f99a6b788047b0b8a7496c2e0c8f372f6edf2 upstream.
If the serial interface is used, the 8-bit address should be latched using
the rising edge of the WR/FSYNC signal.
This basically means that a CS change is required between the first byte
sent, and the second one.
This change splits the single-transfer transfer of 2 bytes into 2 transfers
with a single byte, and CS change in-between.
Note fixes tag is not accurate, but reflects a point beyond which there
are too many refactors to make backporting straight forward.
Fixes: b19e9ad5e2cb ("staging:iio:resolver:ad2s1210 general driver cleanup.")
Signed-off-by: Dragos Bogdan <dragos.bogdan@...log.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@...log.com>
Cc: <Stable@...r.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@...wei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@...uxfoundation.org>
---
drivers/staging/iio/resolver/ad2s1210.c | 17 ++++++++++++-----
1 file changed, 12 insertions(+), 5 deletions(-)
--- a/drivers/staging/iio/resolver/ad2s1210.c
+++ b/drivers/staging/iio/resolver/ad2s1210.c
@@ -126,17 +126,24 @@ static int ad2s1210_config_write(struct
static int ad2s1210_config_read(struct ad2s1210_state *st,
unsigned char address)
{
- struct spi_transfer xfer = {
- .len = 2,
- .rx_buf = st->rx,
- .tx_buf = st->tx,
+ struct spi_transfer xfers[] = {
+ {
+ .len = 1,
+ .rx_buf = &st->rx[0],
+ .tx_buf = &st->tx[0],
+ .cs_change = 1,
+ }, {
+ .len = 1,
+ .rx_buf = &st->rx[1],
+ .tx_buf = &st->tx[1],
+ },
};
int ret = 0;
ad2s1210_set_mode(MOD_CONFIG, st);
st->tx[0] = address | AD2S1210_MSB_IS_HIGH;
st->tx[1] = AD2S1210_REG_FAULT;
- ret = spi_sync_transfer(st->sdev, &xfer, 1);
+ ret = spi_sync_transfer(st->sdev, xfers, 2);
if (ret < 0)
return ret;
st->old_data = true;
Powered by blists - more mailing lists