| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20200528154625.17742-5-sumit.semwal@linaro.org>
Date: Thu, 28 May 2020 21:16:24 +0530
From: Sumit Semwal <sumit.semwal@...aro.org>
To: agross@...nel.org, bjorn.andersson@...aro.org, lgirdwood@...il.com,
broonie@...nel.org, robh+dt@...nel.org
Cc: nishakumari@...eaurora.org, linux-arm-msm@...r.kernel.org,
linux-kernel@...r.kernel.org, devicetree@...r.kernel.org,
kgunda@...eaurora.org, rnayak@...eaurora.org,
Sumit Semwal <sumit.semwal@...aro.org>
Subject: [PATCH v3 4/5] regulator: qcom: Add labibb driver
From: Nisha Kumari <nishakumari@...eaurora.org>
Qualcomm platforms have LAB(LCD AMOLED Boost)/IBB(Inverting Buck Boost)
regulators, labibb for short, which are used as power supply for
LCD Mode displays.
This patch adds labibb regulator driver for pmi8998 PMIC, found on
SDM845 platforms.
Signed-off-by: Nisha Kumari <nishakumari@...eaurora.org>
Signed-off-by: Sumit Semwal <sumit.semwal@...aro.org>
--
v2: sumits: reworked the driver for more common code, and addressed
review comments from v1
v3: sumits: addressed review comments from v2; moved to use core
regulator features like enable_time, off_on_delay, and the newly
added poll_enabled_time. Moved the check_enabled functionality
to core framework via poll_enabled_time.
---
drivers/regulator/Kconfig | 10 +
drivers/regulator/Makefile | 1 +
drivers/regulator/qcom-labibb-regulator.c | 224 ++++++++++++++++++++++
3 files changed, 235 insertions(+)
create mode 100644 drivers/regulator/qcom-labibb-regulator.c
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index f4b72cb098ef..58704a9fd05d 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -1167,5 +1167,15 @@ config REGULATOR_WM8994
This driver provides support for the voltage regulators on the
WM8994 CODEC.
+config REGULATOR_QCOM_LABIBB
+ tristate "QCOM LAB/IBB regulator support"
+ depends on SPMI || COMPILE_TEST
+ help
+ This driver supports Qualcomm's LAB/IBB regulators present on the
+ Qualcomm's PMIC chip pmi8998. QCOM LAB and IBB are SPMI
+ based PMIC implementations. LAB can be used as positive
+ boost regulator and IBB can be used as a negative boost regulator
+ for LCD display panel.
+
endif
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 6610ee001d9a..5b313786c0e8 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -87,6 +87,7 @@ obj-$(CONFIG_REGULATOR_MT6323) += mt6323-regulator.o
obj-$(CONFIG_REGULATOR_MT6358) += mt6358-regulator.o
obj-$(CONFIG_REGULATOR_MT6380) += mt6380-regulator.o
obj-$(CONFIG_REGULATOR_MT6397) += mt6397-regulator.o
+obj-$(CONFIG_REGULATOR_QCOM_LABIBB) += qcom-labibb-regulator.o
obj-$(CONFIG_REGULATOR_QCOM_RPM) += qcom_rpm-regulator.o
obj-$(CONFIG_REGULATOR_QCOM_RPMH) += qcom-rpmh-regulator.o
obj-$(CONFIG_REGULATOR_QCOM_SMD_RPM) += qcom_smd-regulator.o
diff --git a/drivers/regulator/qcom-labibb-regulator.c b/drivers/regulator/qcom-labibb-regulator.c
new file mode 100644
index 000000000000..634d08461c6e
--- /dev/null
+++ b/drivers/regulator/qcom-labibb-regulator.c
@@ -0,0 +1,225 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (c) 2020, The Linux Foundation. All rights reserved.
+
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+
+#define REG_PERPH_TYPE 0x04
+#define QCOM_LAB_TYPE 0x24
+#define QCOM_IBB_TYPE 0x20
+
+#define REG_LABIBB_STATUS1 0x08
+#define REG_LABIBB_ENABLE_CTL 0x46
+#define LABIBB_STATUS1_VREG_OK_BIT BIT(7)
+#define LABIBB_CONTROL_ENABLE BIT(7)
+
+#define LAB_ENABLE_CTL_MASK BIT(7)
+#define IBB_ENABLE_CTL_MASK (BIT(7) | BIT(6))
+
+#define LABIBB_ENABLE_TIME 1000
+#define LAB_POLL_ENABLED_TIME (LABIBB_ENABLE_TIME * 2)
+#define IBB_POLL_ENABLED_TIME (LABIBB_ENABLE_TIME * 10)
+#define LABIBB_OFF_ON_DELAY (8200)
+
+struct labibb_regulator {
+ struct regulator_desc desc;
+ struct device *dev;
+ struct regmap *regmap;
+ struct regulator_dev *rdev;
+ u16 base;
+ u8 type;
+};
+
+struct labibb_regulator_data {
+ u16 base;
+ const char *name;
+ u8 type;
+ unsigned int poll_enabled_time;
+};
+
+static int qcom_labibb_regulator_is_enabled(struct regulator_dev *rdev)
+{
+ int ret;
+ unsigned int val;
+ struct labibb_regulator *reg = rdev_get_drvdata(rdev);
+
+ ret = regmap_read(reg->regmap, reg->base + REG_LABIBB_STATUS1, &val);
+ if (ret < 0) {
+ dev_err(reg->dev, "Read register failed ret = %d\n", ret);
+ return ret;
+ }
+ return !!(val & LABIBB_STATUS1_VREG_OK_BIT);
+}
+
+static int qcom_labibb_regulator_enable(struct regulator_dev *rdev)
+{
+ int ret;
+ struct labibb_regulator *reg = rdev_get_drvdata(rdev);
+
+ ret = regulator_enable_regmap(rdev);
+ if (ret < 0)
+ dev_err(reg->dev, "Write failed: enable %s regulator\n",
+ reg->desc.name);
+
+ return ret;
+}
+
+static int qcom_labibb_regulator_disable(struct regulator_dev *rdev)
+{
+ int ret = 0;
+ struct labibb_regulator *reg = rdev_get_drvdata(rdev);
+
+ ret = regulator_disable_regmap(rdev);
+ if (ret < 0)
+ dev_err(reg->dev, "Disable failed: disable %s\n",
+ reg->desc.name);
+
+ return ret;
+}
+
+static struct regulator_ops qcom_labibb_ops = {
+ .enable = qcom_labibb_regulator_enable,
+ .disable = qcom_labibb_regulator_disable,
+ .is_enabled = qcom_labibb_regulator_is_enabled,
+};
+
+static int register_labibb_regulator(struct labibb_regulator *reg,
+ const struct labibb_regulator_data *reg_data,
+ struct device_node *of_node)
+{
+ struct regulator_config cfg = {};
+
+ reg->base = reg_data->base;
+ reg->type = reg_data->type;
+ reg->desc.enable_reg = reg->base + REG_LABIBB_ENABLE_CTL;
+ reg->desc.enable_val = LABIBB_CONTROL_ENABLE;
+ reg->desc.of_match = reg_data->name;
+ reg->desc.name = reg_data->name;
+ reg->desc.owner = THIS_MODULE;
+ reg->desc.type = REGULATOR_VOLTAGE;
+ reg->desc.ops = &qcom_labibb_ops;
+
+ reg->desc.enable_time = LABIBB_ENABLE_TIME;
+ reg->desc.poll_enabled_time = reg_data->poll_enabled_time;
+ reg->desc.off_on_delay = LABIBB_OFF_ON_DELAY;
+
+ cfg.dev = reg->dev;
+ cfg.driver_data = reg;
+ cfg.regmap = reg->regmap;
+ cfg.of_node = of_node;
+
+ reg->rdev = devm_regulator_register(reg->dev, ®->desc, &cfg);
+ return PTR_ERR_OR_ZERO(reg->rdev);
+}
+
+static const struct labibb_regulator_data pmi8998_labibb_data[] = {
+ {0xde00, "lab", QCOM_LAB_TYPE, LAB_POLL_ENABLED_TIME},
+ {0xdc00, "ibb", QCOM_IBB_TYPE, IBB_POLL_ENABLED_TIME},
+ { },
+};
+
+static const struct of_device_id qcom_labibb_match[] = {
+ { .compatible = "qcom,pmi8998-lab-ibb", .data = &pmi8998_labibb_data},
+ { },
+};
+MODULE_DEVICE_TABLE(of, qcom_labibb_match);
+
+static int qcom_labibb_regulator_probe(struct platform_device *pdev)
+{
+ struct labibb_regulator *labibb_reg;
+ struct device *dev;
+ struct device_node *child;
+ const struct of_device_id *match;
+ const struct labibb_regulator_data *reg_data;
+ struct regmap *reg_regmap;
+ unsigned int type;
+ int ret;
+
+ reg_regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!reg_regmap) {
+ dev_err(&pdev->dev, "Couldn't get parent's regmap\n");
+ return -ENODEV;
+ }
+
+ dev = &pdev->dev;
+
+ match = of_match_device(qcom_labibb_match, &pdev->dev);
+ if (!match)
+ return -ENODEV;
+
+ for (reg_data = match->data; reg_data->name; reg_data++) {
+ child = of_get_child_by_name(pdev->dev.of_node, reg_data->name);
+
+ /* TODO: This validates if the type of regulator is indeed
+ * what's mentioned in DT.
+ * I'm not sure if this is needed, but we'll keep it for now.
+ */
+ ret = regmap_read(reg_regmap, reg_data->base + REG_PERPH_TYPE,
+ &type);
+ if (ret < 0) {
+ dev_err(dev,
+ "Peripheral type read failed ret=%d\n",
+ ret);
+ return -EINVAL;
+ }
+
+ if ((type != QCOM_LAB_TYPE) && (type != QCOM_IBB_TYPE)) {
+ dev_err(dev,
+ "qcom_labibb: unknown peripheral type\n");
+ return -EINVAL;
+ } else if (type != reg_data->type) {
+ dev_err(dev,
+ "qcom_labibb: type %x doesn't match DT %x\n",
+ type, reg_data->type);
+ return -EINVAL;
+ }
+
+ labibb_reg = devm_kzalloc(&pdev->dev, sizeof(*labibb_reg),
+ GFP_KERNEL);
+ if (!labibb_reg)
+ return -ENOMEM;
+
+ labibb_reg->regmap = reg_regmap;
+ labibb_reg->dev = dev;
+
+ switch (reg_data->type) {
+ case QCOM_LAB_TYPE:
+ labibb_reg->desc.enable_mask = LAB_ENABLE_CTL_MASK;
+ break;
+
+ case QCOM_IBB_TYPE:
+ labibb_reg->desc.enable_mask = IBB_ENABLE_CTL_MASK;
+ break;
+ }
+
+ dev_info(dev, "Registering %s regulator\n", child->full_name);
+
+ ret = register_labibb_regulator(labibb_reg, reg_data, child);
+ if (ret < 0) {
+ dev_err(dev,
+ "qcom_labibb: error registering %s : %d\n",
+ child->full_name, ret);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static struct platform_driver qcom_labibb_regulator_driver = {
+ .driver = {
+ .name = "qcom-lab-ibb-regulator",
+ .of_match_table = qcom_labibb_match,
+ },
+ .probe = qcom_labibb_regulator_probe,
+};
+module_platform_driver(qcom_labibb_regulator_driver);
+
+MODULE_DESCRIPTION("Qualcomm labibb driver");
+MODULE_LICENSE("GPL v2");
--
2.26.2
Powered by blists - more mailing lists