Message-ID: <20200530213630.87159-2-tomasz.duszynski@octakon.com>
Date:   Sat, 30 May 2020 23:36:27 +0200
From:   Tomasz Duszynski <tomasz.duszynski@...akon.com>
To:     <linux-iio@...r.kernel.org>
CC:     <linux-kernel@...r.kernel.org>, <devicetree@...r.kernel.org>,
        <robh+dt@...nel.org>, <jic23@...nel.org>,
        <andy.shevchenko@...il.com>, <pmeerw@...erw.net>,
        Tomasz Duszynski <tomasz.duszynski@...akon.com>
Subject: [PATCH v2 1/4] iio: chemical: scd30: add core driver

Add Sensirion SCD30 carbon dioxide core driver.

Signed-off-by: Tomasz Duszynski <tomasz.duszynski@...akon.com>
---
 Documentation/ABI/testing/sysfs-bus-iio-scd30 |  20 +
 MAINTAINERS                                   |   6 +
 drivers/iio/chemical/Kconfig                  |  11 +
 drivers/iio/chemical/Makefile                 |   1 +
 drivers/iio/chemical/scd30.h                  |  75 ++
 drivers/iio/chemical/scd30_core.c             | 764 ++++++++++++++++++
 6 files changed, 877 insertions(+)
 create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-scd30
 create mode 100644 drivers/iio/chemical/scd30.h
 create mode 100644 drivers/iio/chemical/scd30_core.c

diff --git a/Documentation/ABI/testing/sysfs-bus-iio-scd30 b/Documentation/ABI/testing/sysfs-bus-iio-scd30
new file mode 100644
index 000000000000..a05b1d28e94a
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-scd30
@@ -0,0 +1,20 @@
+What:		/sys/bus/iio/devices/iio:deviceX/calibration
+Date:		June 2020
+KernelVersion:	5.8
+Contact:	linux-iio@...r.kernel.org
+Description:
+		Contaminants build-up in the measurement chamber or optical
+		elements deterioration leads to sensor drift.
+
+		One can compensate for sensor drift by using either automatic
+		self calibration (asc) or forced recalibration (frc). If used
+		at once one will overwrite the other.
+
+		Writing 1 or 0 to this attribute will respectively activate or
+		deactivate asc.
+
+		Picking value from the range [400 1 2000] and writing it to the
+		sensor will set frc.
+
+		Upon reading current asc status and frc value are returned
+		respectively.
diff --git a/MAINTAINERS b/MAINTAINERS
index 60ed2963efaa..41a509cca6f1 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -15137,6 +15137,12 @@ S:	Maintained
 F:	drivers/misc/phantom.c
 F:	include/uapi/linux/phantom.h

+SENSIRION SCD30 CARBON DIOXIDE SENSOR DRIVER
+M:	Tomasz Duszynski <tomasz.duszynski@...akon.com>
+S:	Maintained
+F:	drivers/iio/chemical/scd30.h
+F:	drivers/iio/chemical/scd30_core.c
+
 SENSIRION SPS30 AIR POLLUTION SENSOR DRIVER
 M:	Tomasz Duszynski <tduszyns@...il.com>
 S:	Maintained
diff --git a/drivers/iio/chemical/Kconfig b/drivers/iio/chemical/Kconfig
index 7f21afd73b1c..99e852b67e55 100644
--- a/drivers/iio/chemical/Kconfig
+++ b/drivers/iio/chemical/Kconfig
@@ -85,6 +85,17 @@ config PMS7003
 	  To compile this driver as a module, choose M here: the module will
 	  be called pms7003.

+config SCD30_CORE
+	tristate "SCD30 carbon dioxide sensor driver"
+	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
+	help
+	  Say Y here to build support for the Sensirion SCD30 sensor with carbon
+	  dioxide, relative humidity and temperature sensing capabilities.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called scd30_core.
+
 config SENSIRION_SGP30
 	tristate "Sensirion SGPxx gas sensors"
 	depends on I2C
diff --git a/drivers/iio/chemical/Makefile b/drivers/iio/chemical/Makefile
index aba4167db745..c9804b041ecd 100644
--- a/drivers/iio/chemical/Makefile
+++ b/drivers/iio/chemical/Makefile
@@ -12,6 +12,7 @@ obj-$(CONFIG_BME680_SPI) += bme680_spi.o
 obj-$(CONFIG_CCS811)		+= ccs811.o
 obj-$(CONFIG_IAQCORE)		+= ams-iaq-core.o
 obj-$(CONFIG_PMS7003) += pms7003.o
+obj-$(CONFIG_SCD30_CORE) += scd30_core.o
 obj-$(CONFIG_SENSIRION_SGP30)	+= sgp30.o
 obj-$(CONFIG_SPS30) += sps30.o
 obj-$(CONFIG_VZ89X)		+= vz89x.o
diff --git a/drivers/iio/chemical/scd30.h b/drivers/iio/chemical/scd30.h
new file mode 100644
index 000000000000..9b25f7423142
--- /dev/null
+++ b/drivers/iio/chemical/scd30.h
@@ -0,0 +1,75 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _SCD30_H
+#define _SCD30_H
+
+#include <linux/completion.h>
+#include <linux/device.h>
+#include <linux/mutex.h>
+#include <linux/pm.h>
+#include <linux/regulator/consumer.h>
+#include <linux/types.h>
+
+struct scd30_state;
+
+enum scd30_cmd {
+	/* start continuous measurement with pressure compensation */
+	CMD_START_MEAS,
+	/* stop continuous measurement */
+	CMD_STOP_MEAS,
+	/* set/get measurement interval */
+	CMD_MEAS_INTERVAL,
+	/* check whether new measurement is ready */
+	CMD_MEAS_READY,
+	/* get measurement */
+	CMD_READ_MEAS,
+	/* turn on/off automatic self calibration */
+	CMD_ASC,
+	/* set/get forced recalibration value */
+	CMD_FRC,
+	/* set/get temperature offset */
+	CMD_TEMP_OFFSET,
+	/* get firmware version */
+	CMD_FW_VERSION,
+	/* reset sensor */
+	CMD_RESET,
+	/*
+	 * Command for altitude compensation was omitted intentionally because
+	 * the same can be achieved by means of CMD_START_MEAS which takes
+	 * pressure above the sea level as an argument.
+	 */
+};
+
+#define SCD30_MEAS_COUNT 3
+
+typedef int (*scd30_command_t)(struct scd30_state *state, enum scd30_cmd cmd,
+			       u16 arg, void *response, int size);
+
+struct scd30_state {
+	/* serialize access to the device */
+	struct mutex lock;
+	struct device *dev;
+	struct regulator *vdd;
+	struct completion meas_ready;
+	void *priv;
+	int irq;
+	/*
+	 * no way to retrieve current ambient pressure compensation value from
+	 * the sensor so keep one around
+	 */
+	u16 pressure_comp;
+	u16 meas_interval;
+	int meas[SCD30_MEAS_COUNT];
+
+	scd30_command_t command;
+};
+
+int scd30_suspend(struct device *dev);
+int scd30_resume(struct device *dev);
+
+static __maybe_unused SIMPLE_DEV_PM_OPS(scd30_pm_ops, scd30_suspend,
+					scd30_resume);
+
+int scd30_probe(struct device *dev, int irq, const char *name, void *priv,
+		scd30_command_t command);
+
+#endif
diff --git a/drivers/iio/chemical/scd30_core.c b/drivers/iio/chemical/scd30_core.c
new file mode 100644
index 000000000000..3b7d0a7ea7ae
--- /dev/null
+++ b/drivers/iio/chemical/scd30_core.c
@@ -0,0 +1,764 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Sensirion SCD30 carbon dioxide sensor core driver
+ *
+ * Copyright (c) 2020 Tomasz Duszynski <tomasz.duszynski@...akon.com>
+ */
+#include <linux/bits.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/errno.h>
+#include <linux/export.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+#include <linux/iio/trigger.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/iio/triggered_buffer.h>
+#include <linux/iio/types.h>
+#include <linux/interrupt.h>
+#include <linux/irqreturn.h>
+#include <linux/jiffies.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/regulator/consumer.h>
+#include <linux/string.h>
+#include <linux/sysfs.h>
+#include <linux/types.h>
+#include <asm/byteorder.h>
+
+#include "scd30.h"
+
+#define SCD30_PRESSURE_COMP_MIN_MBAR 700
+#define SCD30_PRESSURE_COMP_MAX_MBAR 1400
+#define SCD30_PRESSURE_COMP_DEFAULT 1013
+#define SCD30_MEAS_INTERVAL_MIN_S 2
+#define SCD30_MEAS_INTERVAL_MAX_S 1800
+#define SCD30_MEAS_INTERVAL_DEFAULT SCD30_MEAS_INTERVAL_MIN_S
+#define SCD30_FRC_MIN_PPM 400
+#define SCD30_FRC_MAX_PPM 2000
+#define SCD30_TEMP_OFFSET_MAX 655360
+#define SCD30_EXTRA_TIMEOUT_PER_S 250
+
+enum {
+	SCD30_CONC,
+	SCD30_TEMP,
+	SCD30_HR,
+};
+
+static int scd30_command_write(struct scd30_state *state, enum scd30_cmd cmd,
+			       u16 arg)
+{
+	return state->command(state, cmd, arg, NULL, 0);
+}
+
+static int scd30_command_read(struct scd30_state *state, enum scd30_cmd cmd,
+			      u16 *val)
+{
+	int ret;
+
+	ret = state->command(state, cmd, 0, val, sizeof(*val));
+	*val = be16_to_cpup((__be16 *)val);
+
+	return ret;
+}
+
+static int scd30_reset(struct scd30_state *state)
+{
+	int ret;
+	u16 val;
+
+	ret = scd30_command_write(state, CMD_RESET, 0);
+	if (ret)
+		return ret;
+
+	/* sensor boots up within 2 secs */
+	msleep(2000);
+	/*
+	 * Power-on-reset causes sensor to produce some glitch on i2c bus and
+	 * some controllers end up in error state. Try to recover by placing
+	 * any data on the bus.
+	 */
+	scd30_command_read(state, CMD_MEAS_READY, &val);
+
+	return 0;
+}
+
+/* simplified float to fixed point conversion with a scaling factor of 0.01 */
+static int scd30_float_to_fp(int float32)
+{
+	int fraction, shift,
+	    mantissa = float32 & GENMASK(22, 0),
+	    sign = float32 & BIT(31) ? -1 : 1,
+	    exp = (float32 & ~BIT(31)) >> 23;
+
+	/* special case 0 */
+	if (!exp && !mantissa)
+		return 0;
+
+	exp -= 127;
+	if (exp < 0) {
+		exp = -exp;
+		/* return values ranging from 1 to 99 */
+		return sign * ((((BIT(23) + mantissa) * 100) >> 23) >> exp);
+	}
+
+	/* return values starting at 100 */
+	shift = 23 - exp;
+	float32 = BIT(exp) + (mantissa >> shift);
+	fraction = mantissa & GENMASK(shift - 1, 0);
+
+	return sign * (float32 * 100 + ((fraction * 100) >> shift));
+}
+
+static int scd30_read_meas(struct scd30_state *state)
+{
+	int i, ret;
+
+	ret = state->command(state, CMD_READ_MEAS, 0, state->meas,
+			     sizeof(state->meas));
+	if (ret)
+		return ret;
+
+	be32_to_cpu_array(state->meas, state->meas, ARRAY_SIZE(state->meas));
+
+	for (i = 0; i < ARRAY_SIZE(state->meas); i++)
+		state->meas[i] = scd30_float_to_fp(state->meas[i]);
+
+	return 0;
+}
+
+static int scd30_wait_meas_irq(struct scd30_state *state)
+{
+	int ret, timeout;
+
+	timeout = state->meas_interval * (1000 + SCD30_EXTRA_TIMEOUT_PER_S);
+	timeout = msecs_to_jiffies(timeout);
+	reinit_completion(&state->meas_ready);
+	enable_irq(state->irq);
+	ret = wait_for_completion_interruptible_timeout(&state->meas_ready,
+							timeout);
+	if (ret > 0)
+		ret = 0;
+	else if (!ret)
+		ret = -ETIMEDOUT;
+
+	disable_irq(state->irq);
+
+	return ret;
+}
+
+static int scd30_wait_meas_poll(struct scd30_state *state)
+{
+	int timeout = state->meas_interval * SCD30_EXTRA_TIMEOUT_PER_S;
+	int tries = 5;
+
+	do {
+		int ret;
+		u16 val;
+
+		ret = scd30_command_read(state, CMD_MEAS_READY, &val);
+		if (ret)
+			return -EIO;
+
+		/* new measurement available */
+		if (val)
+			break;
+
+		msleep_interruptible(timeout);
+	} while (--tries);
+
+	return tries ? 0 : -ETIMEDOUT;
+}
+
+static int scd30_read_poll(struct scd30_state *state)
+{
+	int ret;
+
+	ret = scd30_wait_meas_poll(state);
+	if (ret)
+		return ret;
+
+	return scd30_read_meas(state);
+}
+
+static int scd30_read(struct scd30_state *state)
+{
+	if (state->irq > 0)
+		return scd30_wait_meas_irq(state);
+
+	return scd30_read_poll(state);
+}
+
+static int scd30_read_raw(struct iio_dev *indio_dev,
+			  struct iio_chan_spec const *chan,
+			  int *val, int *val2, long mask)
+{
+	struct scd30_state *state = iio_priv(indio_dev);
+	int ret, meas[SCD30_MEAS_COUNT];
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+	case IIO_CHAN_INFO_PROCESSED:
+		ret = iio_device_claim_direct_mode(indio_dev);
+		if (ret)
+			return ret;
+
+		mutex_lock(&state->lock);
+		ret = scd30_read(state);
+		memcpy(meas, state->meas, SCD30_MEAS_COUNT * sizeof(*meas));
+		mutex_unlock(&state->lock);
+		iio_device_release_direct_mode(indio_dev);
+		if (ret)
+			return ret;
+
+		switch (chan->type) {
+		case IIO_CONCENTRATION:
+			*val = meas[chan->address] / 1000000;
+			*val2 = meas[chan->address] % 1000000;
+
+			return IIO_VAL_INT_PLUS_MICRO;
+		case IIO_TEMP:
+		case IIO_HUMIDITYRELATIVE:
+			*val = meas[chan->address] * 10;
+
+			return IIO_VAL_INT;
+		default:
+			return -EINVAL;
+		}
+	case IIO_CHAN_INFO_SCALE:
+		switch (chan->type) {
+		case IIO_CONCENTRATION:
+			*val = 0;
+			*val2 = 1;
+
+			return IIO_VAL_INT_PLUS_MICRO;
+		case IIO_TEMP:
+		case IIO_HUMIDITYRELATIVE:
+			*val = 10;
+
+			return IIO_VAL_INT;
+		default:
+			return -EINVAL;
+		}
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		*val = 0;
+		*val2 = 0;
+
+		mutex_lock(&state->lock);
+		ret = scd30_command_read(state, CMD_MEAS_INTERVAL, (u16 *)val2);
+		mutex_unlock(&state->lock);
+		if (ret)
+			return ret;
+
+		*val2 = 1000000000 / *val2;
+
+		return IIO_VAL_INT_PLUS_NANO;
+	case IIO_CHAN_INFO_CALIBSCALE:
+		mutex_lock(&state->lock);
+		*val = state->pressure_comp / 10;
+		*val2 = (state->pressure_comp % 10) * 100000;
+		mutex_unlock(&state->lock);
+
+		return IIO_VAL_INT_PLUS_MICRO;
+	case IIO_CHAN_INFO_CALIBBIAS:
+		*val = 0;
+		mutex_lock(&state->lock);
+		ret = scd30_command_read(state, CMD_TEMP_OFFSET, (u16 *)val);
+		mutex_unlock(&state->lock);
+
+		return IIO_VAL_INT;
+	}
+
+	return -EINVAL;
+}
+
+static int scd30_write_raw(struct iio_dev *indio_dev,
+			   struct iio_chan_spec const *chan,
+			   int val, int val2, long mask)
+{
+	struct scd30_state *state = iio_priv(indio_dev);
+	int ret = -EINVAL;
+
+	mutex_lock(&state->lock);
+	switch (mask) {
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		if (val)
+			break;
+
+		val = 1000000000 / val2;
+		if (val < SCD30_MEAS_INTERVAL_MIN_S ||
+		    val > SCD30_MEAS_INTERVAL_MAX_S)
+			break;
+
+		ret = scd30_command_write(state, CMD_MEAS_INTERVAL, val);
+		if (ret)
+			break;
+
+		state->meas_interval = val;
+		break;
+	case IIO_CHAN_INFO_CALIBSCALE:
+		val = (val * 1000000 + val2) / 100000;
+		if (val < SCD30_PRESSURE_COMP_MIN_MBAR ||
+		    val > SCD30_PRESSURE_COMP_MAX_MBAR)
+			break;
+
+		ret = scd30_command_write(state, CMD_START_MEAS, val);
+		if (ret)
+			break;
+
+		state->pressure_comp = val;
+		break;
+	case IIO_CHAN_INFO_CALIBBIAS:
+		if (val < 0 || val > SCD30_TEMP_OFFSET_MAX)
+			break;
+		/*
+		 * Manufacturer does not explicitly specify min/max sensible
+		 * values hence check is omitted for simplicity.
+		 */
+		ret = scd30_command_write(state, CMD_TEMP_OFFSET / 10, val);
+	}
+	mutex_unlock(&state->lock);
+
+	return ret;
+}
+
+static int scd30_write_raw_get_fmt(struct iio_dev *indio_dev,
+				   struct iio_chan_spec const *chan, long mask)
+{
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+	case IIO_CHAN_INFO_CALIBBIAS:
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_CALIBSCALE:
+		return IIO_VAL_INT_PLUS_MICRO;
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		return IIO_VAL_INT_PLUS_NANO;
+	}
+
+	return -EINVAL;
+}
+
+static const int scd30_pressure_calibscale_available[] = {
+	SCD30_PRESSURE_COMP_MIN_MBAR / 10, 0,
+	0, 100000,
+	SCD30_PRESSURE_COMP_MAX_MBAR / 10, 0,
+};
+
+static const int scd30_temp_calibbias_available[] = {
+	0, 10, SCD30_TEMP_OFFSET_MAX,
+};
+
+static int scd30_read_avail(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan, const int **vals,
+			    int *type, int *length, long mask)
+{
+	switch (mask) {
+	case IIO_CHAN_INFO_CALIBSCALE:
+		*vals = scd30_pressure_calibscale_available;
+		*type = IIO_VAL_INT_PLUS_MICRO;
+
+		return IIO_AVAIL_RANGE;
+	case IIO_CHAN_INFO_CALIBBIAS:
+		*vals = scd30_temp_calibbias_available;
+		*type = IIO_VAL_INT;
+
+		return IIO_AVAIL_RANGE;
+	}
+
+	return -EINVAL;
+}
+
+static ssize_t sampling_frequency_available_show(struct device *dev,
+						 struct device_attribute *attr,
+						 char *buf)
+{
+	int i = SCD30_MEAS_INTERVAL_MIN_S;
+	ssize_t len = 0;
+
+	do {
+		len += scnprintf(buf + len, PAGE_SIZE - len, "0.%09u ",
+				 1000000000 / i);
+		/*
+		 * Not all values fit PAGE_SIZE buffer hence print every 6th
+		 * (each frequency differs by 6s in time domain from the
+		 * adjecent). Unlisted but valid ones are still accepted.
+		 */
+		i += 6;
+	} while (i <= SCD30_MEAS_INTERVAL_MAX_S);
+
+	buf[len - 1] = '\n';
+
+	return len;
+}
+
+static ssize_t calibration_show(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	struct iio_dev *indio_dev = dev_to_iio_dev(dev);
+	struct scd30_state *state = iio_priv(indio_dev);
+	u16 asc, frc;
+	int ret;
+
+	mutex_lock(&state->lock);
+	ret = scd30_command_read(state, CMD_ASC, &asc);
+	if (ret)
+		goto out;
+
+	ret = scd30_command_read(state, CMD_FRC, &frc);
+out:
+	mutex_unlock(&state->lock);
+
+	return ret ?: sprintf(buf, "%d %d\n", asc, frc);
+}
+
+static ssize_t calibration_store(struct device *dev,
+				 struct device_attribute *attr, const char *buf,
+				 size_t len)
+{
+	struct iio_dev *indio_dev = dev_to_iio_dev(dev);
+	struct scd30_state *state = iio_priv(indio_dev);
+	int ret;
+	u16 val;
+
+	ret = kstrtou16(buf, 0, &val);
+	if (ret)
+		return ret;
+
+	mutex_lock(&state->lock);
+	if (val == 0 || val == 1)
+		ret = scd30_command_write(state, CMD_ASC, val);
+	else if (val >= SCD30_FRC_MIN_PPM && val <= SCD30_FRC_MAX_PPM)
+		ret = scd30_command_write(state, CMD_FRC, val);
+	else
+		ret = -EINVAL;
+	mutex_unlock(&state->lock);
+
+	return ret ?: len;
+}
+
+static IIO_DEVICE_ATTR_RO(sampling_frequency_available, 0);
+static IIO_DEVICE_ATTR_RW(calibration, 0);
+
+static struct attribute *scd30_attrs[] = {
+	&iio_dev_attr_sampling_frequency_available.dev_attr.attr,
+	&iio_dev_attr_calibration.dev_attr.attr,
+	NULL
+};
+
+static const struct attribute_group scd30_attr_group = {
+	.attrs = scd30_attrs,
+};
+
+static const struct iio_info scd30_info = {
+	.attrs = &scd30_attr_group,
+	.read_raw = scd30_read_raw,
+	.write_raw = scd30_write_raw,
+	.write_raw_get_fmt = scd30_write_raw_get_fmt,
+	.read_avail = scd30_read_avail,
+};
+
+#define SCD30_CHAN_SCAN_TYPE(_sign, _realbits) .scan_type = { \
+	.sign = _sign, \
+	.realbits = _realbits, \
+	.storagebits = 32, \
+	.endianness = IIO_CPU, \
+}
+
+static const struct iio_chan_spec scd30_channels[] = {
+	{
+		.type = IIO_PRESSURE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_CALIBSCALE),
+		.info_mask_separate_available = BIT(IIO_CHAN_INFO_CALIBSCALE),
+		.scan_index = -1,
+	},
+	{
+		.type = IIO_CONCENTRATION,
+		.channel2 = IIO_MOD_CO2,
+		.address = SCD30_CONC,
+		.scan_index = SCD30_CONC,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+				      BIT(IIO_CHAN_INFO_SCALE),
+		.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
+		.modified = 1,
+
+		SCD30_CHAN_SCAN_TYPE('u', 16),
+	},
+	{
+		.type = IIO_TEMP,
+		.address = SCD30_TEMP,
+		.scan_index = SCD30_TEMP,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) |
+				      BIT(IIO_CHAN_INFO_CALIBBIAS) |
+				      BIT(IIO_CHAN_INFO_SCALE),
+		.info_mask_separate_available = BIT(IIO_CHAN_INFO_CALIBBIAS),
+		.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
+
+		SCD30_CHAN_SCAN_TYPE('s', 14),
+	},
+	{
+		.type = IIO_HUMIDITYRELATIVE,
+		.address = SCD30_HR,
+		.scan_index = SCD30_HR,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) |
+				      BIT(IIO_CHAN_INFO_SCALE),
+		.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
+
+		SCD30_CHAN_SCAN_TYPE('u', 14),
+	},
+	IIO_CHAN_SOFT_TIMESTAMP(3),
+};
+
+int __maybe_unused scd30_suspend(struct device *dev)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct scd30_state *state  = iio_priv(indio_dev);
+	int ret;
+
+	ret = scd30_command_write(state, CMD_STOP_MEAS, 0);
+	if (ret)
+		return ret;
+
+	return regulator_disable(state->vdd);
+}
+EXPORT_SYMBOL(scd30_suspend);
+
+int __maybe_unused scd30_resume(struct device *dev)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct scd30_state *state = iio_priv(indio_dev);
+	int ret;
+
+	ret = regulator_enable(state->vdd);
+	if (ret)
+		return ret;
+
+	return scd30_command_write(state, CMD_START_MEAS, state->pressure_comp);
+}
+EXPORT_SYMBOL(scd30_resume);
+
+static void scd30_stop_meas(void *data)
+{
+	struct scd30_state *state = data;
+
+	scd30_command_write(state, CMD_STOP_MEAS, 0);
+}
+
+static void scd30_disable_regulator(void *data)
+{
+	struct scd30_state *state = data;
+
+	regulator_disable(state->vdd);
+}
+
+static irqreturn_t scd30_irq_handler(int irq, void *priv)
+{
+	struct iio_dev *indio_dev = priv;
+
+	if (iio_buffer_enabled(indio_dev)) {
+		iio_trigger_poll(indio_dev->trig);
+
+		return IRQ_HANDLED;
+	}
+
+	return IRQ_WAKE_THREAD;
+}
+
+static irqreturn_t scd30_irq_thread_handler(int irq, void *priv)
+{
+	struct iio_dev *indio_dev = priv;
+	struct scd30_state *state = iio_priv(indio_dev);
+	int ret;
+
+	ret = scd30_read_meas(state);
+	if (ret)
+		goto out;
+
+	complete_all(&state->meas_ready);
+out:
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t scd30_trigger_handler(int irq, void *p)
+{
+	struct iio_poll_func *pf = p;
+	struct iio_dev *indio_dev = pf->indio_dev;
+	struct scd30_state *state = iio_priv(indio_dev);
+	struct {
+		int data[SCD30_MEAS_COUNT];
+		u64 ts;
+	} scan;
+	int ret;
+
+	mutex_lock(&state->lock);
+	if (!iio_trigger_using_own(indio_dev))
+		ret = scd30_read_poll(state);
+	else
+		ret = scd30_read_meas(state);
+	memcpy(scan.data, state->meas, sizeof(state->meas));
+	mutex_unlock(&state->lock);
+	if (ret)
+		goto out;
+
+	iio_push_to_buffers_with_timestamp(indio_dev, &scan,
+					   iio_get_time_ns(indio_dev));
+out:
+	iio_trigger_notify_done(indio_dev->trig);
+	return IRQ_HANDLED;
+}
+
+static int scd30_set_trigger_state(struct iio_trigger *trig, bool state)
+{
+	struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig);
+	struct scd30_state *st = iio_priv(indio_dev);
+
+	if (state)
+		enable_irq(st->irq);
+	else
+		disable_irq(st->irq);
+
+	return 0;
+}
+
+static const struct iio_trigger_ops scd30_trigger_ops = {
+	.set_trigger_state = scd30_set_trigger_state,
+};
+
+static int scd30_setup_trigger(struct iio_dev *indio_dev)
+{
+	struct scd30_state *state = iio_priv(indio_dev);
+	struct device *dev = indio_dev->dev.parent;
+	struct iio_trigger *trig;
+	int ret;
+
+	trig = devm_iio_trigger_alloc(dev, "%s-dev%d", indio_dev->name,
+				      indio_dev->id);
+	if (!trig) {
+		dev_err(dev, "failed to allocate trigger\n");
+		return -ENOMEM;
+	}
+
+	trig->dev.parent = dev;
+	trig->ops = &scd30_trigger_ops;
+	iio_trigger_set_drvdata(trig, indio_dev);
+
+	ret = devm_iio_trigger_register(dev, trig);
+	if (ret)
+		return ret;
+
+	indio_dev->trig = iio_trigger_get(trig);
+
+	ret = devm_request_threaded_irq(dev, state->irq, scd30_irq_handler,
+					scd30_irq_thread_handler,
+					IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
+					indio_dev->name, indio_dev);
+	if (ret)
+		dev_err(dev, "failed to request irq\n");
+
+	disable_irq(state->irq);
+
+	return ret;
+}
+
+int scd30_probe(struct device *dev, int irq, const char *name, void *priv,
+		scd30_command_t command)
+{
+	static const unsigned long scd30_scan_masks[] = { 0x07, 0x00 };
+	struct scd30_state *state;
+	struct iio_dev *indio_dev;
+	int ret;
+	u16 val;
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*state));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	state = iio_priv(indio_dev);
+	state->dev = dev;
+	state->priv = priv;
+	state->irq = irq;
+	state->pressure_comp = SCD30_PRESSURE_COMP_DEFAULT;
+	state->meas_interval = SCD30_MEAS_INTERVAL_DEFAULT;
+	state->command = command;
+	mutex_init(&state->lock);
+	init_completion(&state->meas_ready);
+
+	dev_set_drvdata(dev, indio_dev);
+
+	indio_dev->dev.parent = dev;
+	indio_dev->info = &scd30_info;
+	indio_dev->name = name;
+	indio_dev->channels = scd30_channels;
+	indio_dev->num_channels = ARRAY_SIZE(scd30_channels);
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->available_scan_masks = scd30_scan_masks;
+
+	state->vdd = devm_regulator_get(dev, "vdd");
+	if (IS_ERR(state->vdd)) {
+		if (PTR_ERR(state->vdd) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+
+		dev_err(dev, "failed to get regulator\n");
+		return PTR_ERR(state->vdd);
+	}
+
+	ret = regulator_enable(state->vdd);
+	if (ret)
+		return ret;
+
+	ret = devm_add_action_or_reset(dev, scd30_disable_regulator, state);
+	if (ret)
+		return ret;
+
+	ret = devm_add_action_or_reset(dev, scd30_stop_meas, state);
+	if (ret)
+		return ret;
+
+	ret = scd30_reset(state);
+	if (ret) {
+		dev_err(dev, "failed to reset device: %d\n", ret);
+		return ret;
+	}
+
+	if (state->irq > 0) {
+		ret = scd30_setup_trigger(indio_dev);
+		if (ret) {
+			dev_err(dev, "failed to setup trigger: %d\n", ret);
+			return ret;
+		}
+	}
+
+	ret = devm_iio_triggered_buffer_setup(dev, indio_dev, NULL,
+					      scd30_trigger_handler, NULL);
+	if (ret)
+		return ret;
+
+	ret = scd30_command_read(state, CMD_FW_VERSION, &val);
+	if (ret) {
+		dev_err(dev, "failed to read firmware version: %d\n", ret);
+		return ret;
+	}
+	dev_info(dev, "firmware version: %d.%d\n", val >> 8, (char)val);
+
+	ret = scd30_command_write(state, CMD_MEAS_INTERVAL,
+				  state->meas_interval);
+	if (ret) {
+		dev_err(dev, "failed to set measurement interval: %d\n", ret);
+		return ret;
+	}
+
+	ret = scd30_command_write(state, CMD_START_MEAS, state->pressure_comp);
+	if (ret) {
+		dev_err(dev, "failed to start measurement: %d\n", ret);
+		return ret;
+	}
+
+	return devm_iio_device_register(dev, indio_dev);
+}
+EXPORT_SYMBOL(scd30_probe);
+
+MODULE_AUTHOR("Tomasz Duszynski <tomasz.duszynski@...akon.com>");
+MODULE_DESCRIPTION("Sensirion SCD30 carbon dioxide sensor core driver");
+MODULE_LICENSE("GPL v2");
--
2.26.2

Powered by blists - more mailing lists