linux-kernel - Re: [RFC] dt-bindings: mailbox: add doorbell support to ARM MHU

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <CABb+yY27Ngb0C-onkU2qyt=uKgG4iVrcv8hGkC+anypQbTRA1w@mail.gmail.com>
Date:   Thu, 4 Jun 2020 10:15:55 -0500
From:   Jassi Brar <jassisinghbrar@...il.com>
To:     Sudeep Holla <sudeep.holla@....com>
Cc:     Viresh Kumar <viresh.kumar@...aro.org>,
        Rob Herring <robh@...nel.org>, Arnd Bergmann <arnd@...db.de>,
        Frank Rowand <frowand.list@...il.com>,
        Bjorn Andersson <bjorn.andersson@...aro.org>,
        Vincent Guittot <vincent.guittot@...aro.org>,
        linux-arm-kernel <linux-arm-kernel@...ts.infradead.org>,
        Devicetree List <devicetree@...r.kernel.org>,
        Linux Kernel Mailing List <linux-kernel@...r.kernel.org>
Subject: Re: [RFC] dt-bindings: mailbox: add doorbell support to ARM MHU

On Thu, Jun 4, 2020 at 4:20 AM Sudeep Holla <sudeep.holla@....com> wrote:
>
> On Wed, Jun 03, 2020 at 01:32:42PM -0500, Jassi Brar wrote:
> > On Wed, Jun 3, 2020 at 1:04 PM Sudeep Holla <sudeep.holla@....com> wrote:
> > >
> > > On Fri, May 29, 2020 at 09:37:58AM +0530, Viresh Kumar wrote:
> > > > On 28-05-20, 13:20, Rob Herring wrote:
> > > > > Whether Linux
> > > > > requires serializing mailbox accesses is a separate issue. On that side,
> > > > > it seems silly to not allow driving the h/w in the most efficient way
> > > > > possible.
> > > >
> > > > That's exactly what we are trying to say. The hardware allows us to
> > > > write all 32 bits in parallel, without any hardware issues, why
> > > > shouldn't we do that ? The delay (which Sudeep will find out, he is
> > > > facing issues with hardware access because of lockdown right now)
> > >
> > > OK, I was able to access the setup today. I couldn't reach a point
> > > where I can do measurements as the system just became unusable with
> > > one physical channel instead of 2 virtual channels as in my patches.
> > >
> > > My test was simple. Switch to schedutil and read sensors periodically
> > > via sysfs.
> > >
> > >  arm-scmi firmware:scmi: message for 1 is not expected!
> > >
> > This sounds like you are not serialising requests on a shared channel.
> > Can you please also share the patch?
>
> OK, I did try with a small patch initially and then realised we must hit
> issue with mainline as is. Tried and the behaviour is exact same. All
> I did is removed my patches and use bit[0] as the signal. It doesn't
> matter as writes to the register are now serialised. Oh, the above
> message comes when OS times out in advance while firmware continues to
> process the old request and respond.
>
> The trace I sent gives much better view of what's going on.
>
BTW, you didn't even share 'good' vs 'bad' log for me to actually see
if the api lacks.

Let us look closely ...

 >>    bash-1019  [005]  1149.452340: scmi_xfer_begin:
transfer_id=1537 msg_id=7 protocol_id=19 seq=0 poll=1
 >>    bash-1019  [005]  1149.452407: scmi_xfer_end:
transfer_id=1537 msg_id=7 protocol_id=19 seq=0 status=0
>
This round trip took  67usecs.  (log shows some at even 3usecs)
That includes mailbox api overhead, memcpy and the time taken by
remote to respond.
So the api is definitely capable of much faster transfers than you require.

>>     bash-1526  [000]  1149.472553: scmi_xfer_begin:      transfer_id=1538 msg_id=6 protocol_id=21 seq=0 poll=0
>>      <idle>-0     [001]  1149.472733: scmi_xfer_begin:      transfer_id=1539 msg_id=7 protocol_id=19 seq=1 poll=1
>
Here another request is started before the first is finished.
If you want this to work you have to serialise access to the single
physical channel and/or run the remote firmware in asynchronous mode -
that is, the firmware ack the bit as soon as it sees and starts
working in the background, so that we return in ~3usec always, while
the data returns whenever it is ready.  Again, I don't have the code
or the 'good' run log to compare.

PS: I feel it is probably less effort for me to simply let the patch
through, than use my reiki powers to imagine how your test code and
firmware looks like.