linux-kernel - [PATCH V4 0/2] Internal voltage control for qcom SDHC

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <1592321779-28556-1-git-send-email-vbadigan@codeaurora.org>
Date:   Tue, 16 Jun 2020 21:06:17 +0530
From:   Veerabhadrarao Badiganti <vbadigan@...eaurora.org>
To:     adrian.hunter@...el.com, ulf.hansson@...aro.org,
        bjorn.andersson@...aro.org
Cc:     linux-mmc@...r.kernel.org, linux-kernel@...r.kernel.org,
        linux-arm-msm@...r.kernel.org,
        Veerabhadrarao Badiganti <vbadigan@...eaurora.org>
Subject: [PATCH V4 0/2] Internal voltage control for qcom SDHC

On qcom SD host controllers voltage switching be done after the HW
is ready for it. The HW informs its readiness through power irq.
The voltage switching should happen only then.

So added support to register voltage regulators from the msm driver
and use them.

This patchset was posted long back but not actively pursued
https://lore.kernel.org/linux-arm-msm/1539004739-32060-1-git-send-email-vbadigan@codeaurora.org/
So posting it as fresh patchset.  

Changes since V3:	
	- Dropped reading of regulator load values from device tree.
	- Dropped documentaiton chagne.
	- Since only Vqmmc supply of eMMC would be kept On during suspend,
	  setting load only for this regulator so that it can go to LPM.
	  And since this Load reamins same, load value is hard-coded in the driver.

Changes since V2:
	- Removed redundant log from sdhci_msm_set_vmmc.
	- Added the condition for skiping disabling of vqmmc for eMMC.
	- Updated logic such that, setting load for vqmmc only if
	  it is kept ON. 
	- Retained ack by Adrian for second patch.
	- Updated dt properties names as per Robs comments.

Changes since V1:
	- Removed setting load for Vmmc regulator while turning it on/off.
	  Instead setting the active load once during probe.
	- Simplified handlng of supplies for BUS_ON/OFF cases in shci_msm_handle_pwr_irq().
	- Moved common code out of switch case in sdhci_msm_start_signal_voltage_switch().
	- Updated variable name to sdhci_core_to_disable_vqmmc.
	- Updated pr_err logs to dev_err logs.

Veerabhadrarao Badiganti (2):
  dt-bindings: mmc: Supply max load for mmc supplies
  mmc: sdhci-msm: Use internal voltage control

Vijay Viswanath (1):
  mmc: sdhci: Allow platform controlled voltage switching

 drivers/mmc/host/sdhci-msm.c | 208 +++++++++++++++++++++++++++++++++++++++++--
 drivers/mmc/host/sdhci.c     |  32 ++++---
 drivers/mmc/host/sdhci.h     |   1 +
 3 files changed, 219 insertions(+), 22 deletions(-)

-- 
Qualcomm India Private Limited, on behalf of Qualcomm Innovation Center, Inc., is a member of Code Aurora Forum, a Linux Foundation Collaborative Project