linux-kernel - [PATCH v8 1/3] media: rcar-csi2: Correct the selection of hsfreqrange

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <1592476472-26235-1-git-send-email-sudipi@jp.adit-jv.com>
Date:   Thu, 18 Jun 2020 19:34:30 +0900
From:   Suresh Udipi <sudipi@...adit-jv.com>
To:     <mrodin@...adit-jv.com>
CC:     <akiyama@...-osk.co.jp>, <efriedrich@...adit-jv.com>,
        <erosca@...adit-jv.com>, <linux-kernel@...r.kernel.org>,
        <linux-media@...r.kernel.org>, <linux-renesas-soc@...r.kernel.org>,
        <mchehab@...nel.org>, <michael@...in.online>,
        <niklas.soderlund@...natech.se>, <securitycheck@...so.co.jp>,
        <sudipi@...adit-jv.com>
Subject: [PATCH v8 1/3] media: rcar-csi2: Correct the selection of hsfreqrange

hsfreqrange should be chosen based on the calculated mbps which
is closer to the default bit rate  and within the range as per
table[1]. But current calculation always selects first value which
is greater than or equal to the calculated mbps which may lead
to chosing a wrong range in some cases.

For example for 360 mbps for H3/M3N
Existing logic selects
Calculated value 360Mbps : Default 400Mbps Range [368.125 -433.125 mbps]

This hsfreqrange is out of range.

The logic is changed to get the default value which is closest to the
calculated value [1]

Calculated value 360Mbps : Default 350Mbps  Range [320.625 -380.625 mpbs]

[1] specs r19uh0105ej0200-r-car-3rd-generation.pdf [Table 25.9]

Please note that According to Renesas in Table 25.9 the range for
220 default value is corrected as below

 |Range (Mbps)     |  Default  Bit rate (Mbps) |
 -----------------------------------------------
 | 197.125-244.125 |     220                   |
 -----------------------------------------------

Fixes: 769afd212b16 ("media: rcar-csi2: add Renesas R-Car MIPI CSI-2 receiver driver")

Signed-off-by: Suresh Udipi <sudipi@...adit-jv.com>
Signed-off-by: Kazuyoshi Akiyama <akiyama@...-osk.co.jp>
Signed-off-by: Michael Rodin <mrodin@...adit-jv.com>
---
 Changes in v2:
  - Added the boundary check for the maximum bit rate.

  - Simplified the logic by remmoving range check
    as only the closest default value covers most
    of the use cases.

  - Aligning the commit message based on the above change


 Changes in v3:
    - Added max member from struct rcsi2_mbps_reg.
      mbps varialbe cannot be removed from rcsi2_mbps_reg,
      since this structure is reused for
      phtw_mbps_h3_v3h_m3n/phtw_mbps_v3m_e3 where mbps is
      used.


   -  Update the walk of the array in rcsi2_set_phypll() so that it finds
      the first entry where the calculated bit rate is less than the max.

   - Support lower bit rates less than 80Mbps like 48Mbps
     (Raspberry pi camera 640x480 connected to Kingfisher)
     can also be supported by selecting the lowest default bit rate 80Mbps
     as done before this fix

   - Alignement of the commit message based on above changes.

 Changes in v4:
  -  Remove unncessary braces.

 Changes in v5:
   - Removed mbps variable in rcsi2_mbps_reg and aligned all
     tables accordingly


 Changes in v6
   - Renesas correct the range of default value 220Mbps. Now
     if we select the nearest value to the default value all
         the values are in range. So reverting back to original patch
  
   - Added warning for values less than Minimum 80Mbps
      
Changes in v7
  - Create a seperate commit for the warning message less
    than minimum 80Mbps 
  
  - Reorder the statements to increase readability
  
Changes in v8
  - Extended the logic of selection of nearest mbps to
    PHTW registers value less than 250Mbps. A new commit
    is added
	
 drivers/media/platform/rcar-vin/rcar-csi2.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/media/platform/rcar-vin/rcar-csi2.c b/drivers/media/platform/rcar-vin/rcar-csi2.c
index 151e6a9..f18dedc 100644
--- a/drivers/media/platform/rcar-vin/rcar-csi2.c
+++ b/drivers/media/platform/rcar-vin/rcar-csi2.c
@@ -431,16 +431,23 @@ static int rcsi2_wait_phy_start(struct rcar_csi2 *priv)
 static int rcsi2_set_phypll(struct rcar_csi2 *priv, unsigned int mbps)
 {
 	const struct rcsi2_mbps_reg *hsfreq;
+	const struct rcsi2_mbps_reg *hsfreq_prev = NULL;
 
-	for (hsfreq = priv->info->hsfreqrange; hsfreq->mbps != 0; hsfreq++)
+	for (hsfreq = priv->info->hsfreqrange; hsfreq->mbps != 0; hsfreq++) {
 		if (hsfreq->mbps >= mbps)
 			break;
+		hsfreq_prev = hsfreq;
+	}
 
 	if (!hsfreq->mbps) {
 		dev_err(priv->dev, "Unsupported PHY speed (%u Mbps)", mbps);
 		return -ERANGE;
 	}
 
+	if (hsfreq_prev &&
+	    ((mbps - hsfreq_prev->mbps) <= (hsfreq->mbps - mbps)))
+		hsfreq = hsfreq_prev;
+
 	rcsi2_write(priv, PHYPLL_REG, PHYPLL_HSFREQRANGE(hsfreq->reg));
 
 	return 0;
-- 
2.7.4