linux-kernel - [PATCH 3/3] ARM: dts: meson8b: odroidc1: enable the SDHC controller

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <20200620163654.37207-4-martin.blumenstingl@googlemail.com>
Date:   Sat, 20 Jun 2020 18:36:54 +0200
From:   Martin Blumenstingl <martin.blumenstingl@...glemail.com>
To:     linux-amlogic@...ts.infradead.org, khilman@...libre.com
Cc:     linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
        Martin Blumenstingl <martin.blumenstingl@...glemail.com>
Subject: [PATCH 3/3] ARM: dts: meson8b: odroidc1: enable the SDHC controller

Odroid-C1 has an eMMC connector where users can optionally install an
eMMC module. The eMMC modules run off a 1.8V VQMMC supply which means
that HS-200 mode can be used (this is the highest mode that the SDHC
controller supports). Enable the SDHC controller so eMMC modules can be
accessed.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@...glemail.com>
---
 arch/arm/boot/dts/meson8b-odroidc1.dts | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts
index cb21ac9f517c..0c26467de4d0 100644
--- a/arch/arm/boot/dts/meson8b-odroidc1.dts
+++ b/arch/arm/boot/dts/meson8b-odroidc1.dts
@@ -15,6 +15,7 @@ / {
 	aliases {
 		serial0 = &uart_AO;
 		mmc0 = &sd_card_slot;
+		mmc1 = &sdhc;
 	};
 
 	chosen {
@@ -26,6 +27,11 @@ memory {
 		reg = <0x40000000 0x40000000>;
 	};
 
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		blue {
@@ -310,6 +316,26 @@ &saradc {
 	vref-supply = <&vcc_1v8>;
 };
 
+&sdhc {
+	status = "okay";
+
+	pinctrl-0 = <&sdxc_c_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <8>;
+	max-frequency = <100000000>;
+
+	disable-wp;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	no-sdio;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+};
+
 &sdio {
 	status = "okay";
 
-- 
2.27.0