| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20200710143733.30751-3-dmurphy@ti.com>
Date: Fri, 10 Jul 2020 09:37:33 -0500
From: Dan Murphy <dmurphy@...com>
To: <andrew@...n.ch>, <f.fainelli@...il.com>, <hkallweit1@...il.com>,
<davem@...emloft.net>, <robh@...nel.org>
CC: <netdev@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
<devicetree@...r.kernel.org>, Dan Murphy <dmurphy@...com>
Subject: [PATCH net-next v2 2/2] net: phy: DP83822: Add ability to advertise Fiber connection
The DP83822 can be configured to use a Fiber connection. The strap
register is read to determine if the device has been configured to use
a fiber connection. With the fiber connection the PHY can be configured
to detect whether the fiber connection is active by either a high signal
or a low signal.
Fiber mode is only applicable to the DP83822 so rework the PHY match
table so that non-fiber PHYs can still use the same driver but not call
or use any of the fiber features.
Signed-off-by: Dan Murphy <dmurphy@...com>
---
drivers/net/phy/dp83822.c | 161 ++++++++++++++++++++++++++++++++++++++
1 file changed, 161 insertions(+)
diff --git a/drivers/net/phy/dp83822.c b/drivers/net/phy/dp83822.c
index 37643c468e19..b797e3d2a4e5 100644
--- a/drivers/net/phy/dp83822.c
+++ b/drivers/net/phy/dp83822.c
@@ -23,16 +23,29 @@
#define DP83822_DEVADDR 0x1f
+#define MII_DP83822_CTRL_2 0x0a
+#define MII_DP83822_PHYSTS 0x10
#define MII_DP83822_PHYSCR 0x11
#define MII_DP83822_MISR1 0x12
#define MII_DP83822_MISR2 0x13
#define MII_DP83822_RCSR 0x17
#define MII_DP83822_RESET_CTRL 0x1f
#define MII_DP83822_GENCFG 0x465
+#define MII_DP83822_SOR1 0x467
+
+/* GENCFG */
+#define DP83822_SIG_DET_LOW BIT(0)
+
+/* Control Register 2 bits */
+#define DP83822_FX_ENABLE BIT(14)
#define DP83822_HW_RESET BIT(15)
#define DP83822_SW_RESET BIT(14)
+/* PHY STS bits */
+#define DP83822_PHYSTS_DUPLEX BIT(2)
+#define DP83822_PHYSTS_10 BIT(1)
+
/* PHYSCR Register Fields */
#define DP83822_PHYSCR_INT_OE BIT(0) /* Interrupt Output Enable */
#define DP83822_PHYSCR_INTEN BIT(1) /* Interrupt Enable */
@@ -83,6 +96,21 @@
#define DP83822_RX_CLK_SHIFT BIT(12)
#define DP83822_TX_CLK_SHIFT BIT(11)
+/* SOR1 bits */
+#define DP83822_FX_EN_STRAP BIT(11)
+#define DP83822_FX_SD_EN_STRAP BIT(8)
+
+#define MII_DP83822_FIBER_ADVERTISE (SUPPORTED_AUI | SUPPORTED_FIBRE | \
+ SUPPORTED_BNC | SUPPORTED_Pause | \
+ SUPPORTED_Asym_Pause | \
+ SUPPORTED_100baseT_Full)
+
+struct dp83822_private {
+ bool fx_signal_det_low;
+ int fx_enabled;
+ u16 fx_sd_enable;
+};
+
static int dp83822_ack_interrupt(struct phy_device *phydev)
{
int err;
@@ -270,13 +298,40 @@ static int dp8382x_disable_wol(struct phy_device *phydev)
MII_DP83822_WOL_CFG, value);
}
+static int dp83822_read_status(struct phy_device *phydev)
+{
+ int status = phy_read(phydev, MII_DP83822_PHYSTS);
+ int ret;
+
+ ret = genphy_read_status(phydev);
+ if (ret)
+ return ret;
+
+ if (status < 0)
+ return status;
+
+ if (status & DP83822_PHYSTS_DUPLEX)
+ phydev->duplex = DUPLEX_FULL;
+ else
+ phydev->duplex = DUPLEX_HALF;
+
+ if (status & DP83822_PHYSTS_10)
+ phydev->speed = SPEED_10;
+ else
+ phydev->speed = SPEED_100;
+
+ return 0;
+}
+
static int dp83822_config_init(struct phy_device *phydev)
{
+ struct dp83822_private *dp83822 = phydev->priv;
struct device *dev = &phydev->mdio.dev;
int rgmii_delay;
s32 rx_int_delay;
s32 tx_int_delay;
int err = 0;
+ int bmcr;
if (phy_interface_is_rgmii(phydev)) {
rx_int_delay = phy_get_internal_delay(phydev, dev, NULL, 0,
@@ -302,6 +357,48 @@ static int dp83822_config_init(struct phy_device *phydev)
}
}
+ if (dp83822->fx_enabled) {
+ err = phy_modify(phydev, MII_DP83822_CTRL_2,
+ DP83822_FX_ENABLE, 1);
+ if (err < 0)
+ return err;
+
+ linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT,
+ phydev->supported);
+ linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT,
+ phydev->advertising);
+
+ /* Auto neg is not supported in fiber mode */
+ bmcr = phy_read(phydev, MII_BMCR);
+ if (bmcr < 0)
+ return bmcr;
+
+ if (bmcr & BMCR_ANENABLE) {
+ err = phy_modify(phydev, MII_BMCR, BMCR_ANENABLE, 0);
+ if (err < 0)
+ return err;
+ }
+ phydev->autoneg = AUTONEG_DISABLE;
+
+ /* Setup fiber advertisement */
+ err = phy_modify_changed(phydev, MII_ADVERTISE,
+ ADVERTISE_1000XFULL |
+ ADVERTISE_1000XPAUSE |
+ ADVERTISE_1000XPSE_ASYM,
+ MII_DP83822_FIBER_ADVERTISE);
+
+ if (err < 0)
+ return err;
+
+ if (dp83822->fx_signal_det_low) {
+ err = phy_set_bits_mmd(phydev, DP83822_DEVADDR,
+ MII_DP83822_GENCFG,
+ DP83822_SIG_DET_LOW);
+ if (err)
+ return err;
+ }
+ }
+
return dp8382x_disable_wol(phydev);
}
@@ -321,6 +418,68 @@ static int dp83822_phy_reset(struct phy_device *phydev)
return phydev->drv->config_init(phydev);
}
+#ifdef CONFIG_OF_MDIO
+static int dp83822_of_init(struct phy_device *phydev)
+{
+ struct dp83822_private *dp83822 = phydev->priv;
+ struct device *dev = &phydev->mdio.dev;
+
+ /* Signal detection for the PHY is only enabled if the FX_EN and the
+ * SD_EN pins are strapped. Signal detection can only enabled if FX_EN
+ * is strapped otherwise signal detection is disabled for the PHY.
+ */
+ if (dp83822->fx_enabled && dp83822->fx_sd_enable)
+ dp83822->fx_signal_det_low = device_property_present(dev,
+ "ti,link-loss-low");
+ if (!dp83822->fx_enabled)
+ dp83822->fx_enabled = device_property_present(dev,
+ "ti,fiber-mode");
+
+ return 0;
+}
+#else
+static int dp83822_of_init(struct phy_device *phydev)
+{
+ return 0;
+}
+#endif /* CONFIG_OF_MDIO */
+
+static int dp83822_read_straps(struct phy_device *phydev)
+{
+ struct dp83822_private *dp83822 = phydev->priv;
+ int val;
+
+ val = phy_read_mmd(phydev, DP83822_DEVADDR, MII_DP83822_SOR1);
+ if (val < 0)
+ return val;
+
+ dp83822->fx_enabled = val & DP83822_FX_EN_STRAP;
+ dp83822->fx_sd_enable = val & DP83822_FX_SD_EN_STRAP;
+
+ return 0;
+}
+
+static int dp83822_probe(struct phy_device *phydev)
+{
+ struct dp83822_private *dp83822;
+ int ret;
+
+ dp83822 = devm_kzalloc(&phydev->mdio.dev, sizeof(*dp83822),
+ GFP_KERNEL);
+ if (!dp83822)
+ return -ENOMEM;
+
+ phydev->priv = dp83822;
+
+ ret = dp83822_read_straps(phydev);
+ if (ret)
+ return ret;
+
+ dp83822_of_init(phydev);
+
+ return 0;
+}
+
static int dp83822_suspend(struct phy_device *phydev)
{
int value;
@@ -352,8 +511,10 @@ static int dp83822_resume(struct phy_device *phydev)
PHY_ID_MATCH_MODEL(_id), \
.name = (_name), \
/* PHY_BASIC_FEATURES */ \
+ .probe = dp83822_probe, \
.soft_reset = dp83822_phy_reset, \
.config_init = dp83822_config_init, \
+ .read_status = dp83822_read_status, \
.get_wol = dp83822_get_wol, \
.set_wol = dp83822_set_wol, \
.ack_interrupt = dp83822_ack_interrupt, \
--
2.27.0
Powered by blists - more mailing lists