| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20200715224248.GA3490@xilinx.com>
Date: Wed, 15 Jul 2020 15:42:49 -0700
From: Hyun Kwon <hyun.kwon@...inx.com>
To: Vishal Sagar <vishal.sagar@...inx.com>
Cc: "laurent.pinchart@...asonboard.com"
<laurent.pinchart@...asonboard.com>,
"hverkuil@...all.nl" <hverkuil@...all.nl>,
"mchehab@...nel.org" <mchehab@...nel.org>,
"robh+dt@...nel.org" <robh+dt@...nel.org>,
"mark.rutland@....com" <mark.rutland@....com>,
Michal Simek <michals@...inx.com>,
"linux-media@...r.kernel.org" <linux-media@...r.kernel.org>,
"devicetree@...r.kernel.org" <devicetree@...r.kernel.org>,
"linux-arm-kernel@...ts.infradead.org"
<linux-arm-kernel@...ts.infradead.org>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
"joe@...ches.com" <joe@...ches.com>,
Sandip Kothari <sandipk@...inx.com>,
Dinesh Kumar <dineshk@...inx.com>,
Vishal Sagar <vsagar@...inx.com>
Subject: Re: [PATCH v3 3/3] media: v4l: xilinx: Add Xilinx UHD-SDI Rx
Subsystem driver
Hi Vishal,
Thank you for the patch. Sorry for late response.
On Wed, Jun 17, 2020 at 10:33:04PM -0700, Vishal Sagar wrote:
> The Xilinx UHD-SDI Rx subsystem soft IP is used to capture native SDI
> streams from SDI sources like SDI broadcast equipment like cameras and
> mixers. This block outputs either native SDI, native video or
> AXI4-Stream compliant data stream for further processing. Please refer
> to PG290 for details.
>
> The driver is used to configure the IP to add framer, search for
> specific modes, get the detected mode, stream parameters, errors, etc.
> It also generates events for video lock/unlock, bridge over/under flow.
>
> The driver supports 10/12 bpc YUV 422 media bus format currently. It
> also decodes the stream parameters based on the ST352 packet embedded in the
> stream. In case the ST352 packet isn't present in the stream, the core's
> detected properties are used to set stream properties.
>
> The driver currently supports only the AXI4-Stream IP configuration.
>
> Signed-off-by: Vishal Sagar <vishal.sagar@...inx.com>
> ---
> v3
> - fixed KConfig with better description
> - removed unnecessary header files
> - converted uppercase to lowercase for all hex values
> - merged core struct to state struct
> - removed most one line functions and replaced with direct reg
> read/write or macros
> - dt property bpp to bpc. default 10. not mandatory.
> - fixed subscribe events, log_status, s_stream
> - merged overflow/underflow to one event
> - moved all controls to xilinx-sdirxss.h
> - max events from 128 to 8
> - used FIELD_GET() instead of custom macro
> - updated the controls documentation
> - added spinlock
> - removed 3GB control and added mode to detect bitmask
> - fixed format for (width, height, colorspace, xfer func, etc)
> - added dv_timings_cap, s/g_dv_timings
> - fixed set/get_format
> - fix v4l control registrations
> - fix order of registration / deregistration in probe() remove()
> - fixed other comments from Hyun, Laurent and Hans
> - things yet to close
> - adding source port for connector (Laurent's suggestion)
> - adding new FIELD type for Transport Stream V4L2_FIELD_ALTERNATE_PROG (Han's suggestion)
> - Update / remove EDH or CRC related controls
>
> v2
> - Added DV timing support based on Hans Verkuilś feedback
> - More documentation to custom v4l controls and events
> - Fixed Hyunś comments
> - Added macro for masking and shifting as per Joe Perches comments
> - Updated to latest as per Xilinx github repo driver like
> adding new DV timings not in mainline yet uptill 03/21/20
>
> drivers/media/platform/xilinx/Kconfig | 11 +
> drivers/media/platform/xilinx/Makefile | 1 +
> .../media/platform/xilinx/xilinx-sdirxss.c | 2121 +++++++++++++++++
> include/uapi/linux/v4l2-controls.h | 6 +
> include/uapi/linux/xilinx-sdirxss.h | 283 +++
> 5 files changed, 2422 insertions(+)
> create mode 100644 drivers/media/platform/xilinx/xilinx-sdirxss.c
> create mode 100644 include/uapi/linux/xilinx-sdirxss.h
>
> diff --git a/drivers/media/platform/xilinx/Kconfig b/drivers/media/platform/xilinx/Kconfig
> index 01c96fb66414..578cdcc1036e 100644
> --- a/drivers/media/platform/xilinx/Kconfig
> +++ b/drivers/media/platform/xilinx/Kconfig
> @@ -12,6 +12,17 @@ config VIDEO_XILINX
>
> if VIDEO_XILINX
>
> +config VIDEO_XILINX_SDIRXSS
> + tristate "Xilinx UHD SDI Rx Subsystem"
> + help
> + Driver for Xilinx UHD-SDI Rx Subsystem. This is a V4L sub-device
> + based driver that takes input from a SDI source like SDI camera and
> + converts it into an AXI4-Stream. The subsystem comprises a SMPTE
> + UHD-SDI Rx core, a SDI Rx to Native Video bridge and a Video In to
> + AXI4-Stream bridge. The driver is used to set different stream
> + detection modes and identify stream properties to properly configure
> + downstream.
> +
> config VIDEO_XILINX_TPG
> tristate "Xilinx Video Test Pattern Generator"
> depends on VIDEO_XILINX
> diff --git a/drivers/media/platform/xilinx/Makefile b/drivers/media/platform/xilinx/Makefile
> index 4cdc0b1ec7a5..3beaf24d832c 100644
> --- a/drivers/media/platform/xilinx/Makefile
> +++ b/drivers/media/platform/xilinx/Makefile
> @@ -3,5 +3,6 @@
> xilinx-video-objs += xilinx-dma.o xilinx-vip.o xilinx-vipp.o
>
> obj-$(CONFIG_VIDEO_XILINX) += xilinx-video.o
> +obj-$(CONFIG_VIDEO_XILINX_SDIRXSS) += xilinx-sdirxss.o
> obj-$(CONFIG_VIDEO_XILINX_TPG) += xilinx-tpg.o
> obj-$(CONFIG_VIDEO_XILINX_VTC) += xilinx-vtc.o
> diff --git a/drivers/media/platform/xilinx/xilinx-sdirxss.c b/drivers/media/platform/xilinx/xilinx-sdirxss.c
> new file mode 100644
> index 000000000000..e39aab7c656a
> --- /dev/null
> +++ b/drivers/media/platform/xilinx/xilinx-sdirxss.c
> @@ -0,0 +1,2121 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Driver for Xilinx SDI Rx Subsystem
> + *
> + * Copyright (C) 2017 - 2020 Xilinx, Inc.
> + *
> + * Contacts: Vishal Sagar <vishal.sagar@...inx.com>
> + */
> +
> +#include <dt-bindings/media/xilinx-sdi.h>
> +#include <linux/bits.h>
> +#include <linux/bitfield.h>
> +#include <linux/clk.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/xilinx-sdirxss.h>
> +#include <media/media-entity.h>
> +#include <media/v4l2-ctrls.h>
> +#include <media/v4l2-dv-timings.h>
> +#include <media/v4l2-event.h>
> +#include <media/v4l2-subdev.h>
> +
> +/*
> + * SDI Rx register map, bitmask and offsets
> + */
> +#define XSDIRX_RST_CTRL_REG 0x00
> +#define XSDIRX_MDL_CTRL_REG 0x04
> +#define XSDIRX_GLBL_IER_REG 0x0c
> +#define XSDIRX_ISR_REG 0x10
> +#define XSDIRX_IER_REG 0x14
> +#define XSDIRX_ST352_VALID_REG 0x18
> +#define XSDIRX_ST352_DS1_REG 0x1c
> +#define XSDIRX_ST352_DS3_REG 0x20
> +#define XSDIRX_ST352_DS5_REG 0x24
> +#define XSDIRX_ST352_DS7_REG 0x28
> +#define XSDIRX_ST352_DS9_REG 0x2c
> +#define XSDIRX_ST352_DS11_REG 0x30
> +#define XSDIRX_ST352_DS13_REG 0x34
> +#define XSDIRX_ST352_DS15_REG 0x38
> +#define XSDIRX_VERSION_REG 0x3c
> +#define XSDIRX_SS_CONFIG_REG 0x40
> +#define XSDIRX_MODE_DET_STAT_REG 0x44
> +#define XSDIRX_TS_DET_STAT_REG 0x48
> +#define XSDIRX_EDH_STAT_REG 0x4c
> +#define XSDIRX_EDH_ERRCNT_EN_REG 0x50
> +#define XSDIRX_EDH_ERRCNT_REG 0x54
> +#define XSDIRX_CRC_ERRCNT_REG 0x58
> +#define XSDIRX_VID_LOCK_WINDOW_REG 0x5c
> +#define XSDIRX_ST352_DS2_REG 0x70
> +#define XSDIRX_ST352_DS4_REG 0x74
> +#define XSDIRX_ST352_DS6_REG 0x78
> +#define XSDIRX_ST352_DS8_REG 0x7c
> +#define XSDIRX_ST352_DS10_REG 0x80
> +#define XSDIRX_ST352_DS12_REG 0x84
> +#define XSDIRX_ST352_DS14_REG 0x88
> +#define XSDIRX_ST352_DS16_REG 0x8c
> +
> +#define XSDIRX_RST_CTRL_SS_EN_MASK BIT(0)
> +#define XSDIRX_RST_CTRL_SRST_MASK BIT(1)
> +#define XSDIRX_RST_CTRL_RST_CRC_ERRCNT_MASK BIT(2)
> +#define XSDIRX_RST_CTRL_RST_EDH_ERRCNT_MASK BIT(3)
> +#define XSDIRX_RST_CTRL_SDIRX_BRIDGE_ENB_MASK BIT(8)
> +#define XSDIRX_RST_CTRL_VIDIN_AXI4S_MOD_ENB_MASK BIT(9)
> +#define XSDIRX_RST_CTRL_BRIDGE_CH_FMT_OFFSET 10
> +#define XSDIRX_RST_CTRL_BRIDGE_CH_FMT_MASK GENMASK(12, 10)
> +#define XSDIRX_RST_CTRL_BRIDGE_CH_FMT_YUV444 1
> +
> +#define XSDIRX_MDL_CTRL_FRM_EN_MASK BIT(4)
> +#define XSDIRX_MDL_CTRL_MODE_DET_EN_MASK BIT(5)
> +#define XSDIRX_MDL_CTRL_MODE_HD_EN_MASK BIT(8)
> +#define XSDIRX_MDL_CTRL_MODE_SD_EN_MASK BIT(9)
> +#define XSDIRX_MDL_CTRL_MODE_3G_EN_MASK BIT(10)
> +#define XSDIRX_MDL_CTRL_MODE_6G_EN_MASK BIT(11)
> +#define XSDIRX_MDL_CTRL_MODE_12GI_EN_MASK BIT(12)
> +#define XSDIRX_MDL_CTRL_MODE_12GF_EN_MASK BIT(13)
> +#define XSDIRX_MDL_CTRL_MODE_AUTO_DET_MASK GENMASK(13, 8)
> +
> +#define XSDIRX_MDL_CTRL_FORCED_MODE_OFFSET 16
> +#define XSDIRX_MDL_CTRL_FORCED_MODE_MASK GENMASK(18, 16)
> +
> +#define XSDIRX_GLBL_INTR_EN_MASK BIT(0)
> +
> +#define XSDIRX_INTR_VIDLOCK_MASK BIT(0)
> +#define XSDIRX_INTR_VIDUNLOCK_MASK BIT(1)
> +#define XSDIRX_INTR_OVERFLOW_MASK BIT(9)
> +#define XSDIRX_INTR_UNDERFLOW_MASK BIT(10)
> +
> +#define XSDIRX_INTR_ALL_MASK (XSDIRX_INTR_VIDLOCK_MASK |\
> + XSDIRX_INTR_VIDUNLOCK_MASK |\
> + XSDIRX_INTR_OVERFLOW_MASK |\
> + XSDIRX_INTR_UNDERFLOW_MASK)
> +
> +#define XSDIRX_ST352_VALID_DS1_MASK BIT(0)
> +#define XSDIRX_ST352_VALID_DS3_MASK BIT(1)
> +#define XSDIRX_ST352_VALID_DS5_MASK BIT(2)
> +#define XSDIRX_ST352_VALID_DS7_MASK BIT(3)
> +#define XSDIRX_ST352_VALID_DS9_MASK BIT(4)
> +#define XSDIRX_ST352_VALID_DS11_MASK BIT(5)
> +#define XSDIRX_ST352_VALID_DS13_MASK BIT(6)
> +#define XSDIRX_ST352_VALID_DS15_MASK BIT(7)
> +
> +#define XSDIRX_MODE_DET_STAT_RX_MODE_MASK GENMASK(2, 0)
> +#define XSDIRX_MODE_DET_STAT_MODE_LOCK_MASK BIT(3)
> +#define XSDIRX_MODE_DET_STAT_ACT_STREAM_MASK GENMASK(6, 4)
> +#define XSDIRX_MODE_DET_STAT_ACT_STREAM_OFFSET 4
> +#define XSDIRX_MODE_DET_STAT_LVLB_3G_MASK BIT(7)
> +
> +#define XSDIRX_TS_DET_STAT_LOCKED_MASK BIT(0)
> +#define XSDIRX_TS_DET_STAT_SCAN_MASK BIT(1)
> +#define XSDIRX_TS_DET_STAT_FAMILY_MASK GENMASK(7, 4)
> +#define XSDIRX_TS_DET_STAT_RATE_MASK GENMASK(11, 8)
> +
> +#define XSDIRX_TS_DET_STAT_RATE_NONE 0x0
> +#define XSDIRX_TS_DET_STAT_RATE_23_98HZ 0x2
> +#define XSDIRX_TS_DET_STAT_RATE_24HZ 0x3
> +#define XSDIRX_TS_DET_STAT_RATE_47_95HZ 0x4
> +#define XSDIRX_TS_DET_STAT_RATE_25HZ 0x5
> +#define XSDIRX_TS_DET_STAT_RATE_29_97HZ 0x6
> +#define XSDIRX_TS_DET_STAT_RATE_30HZ 0x7
> +#define XSDIRX_TS_DET_STAT_RATE_48HZ 0x8
> +#define XSDIRX_TS_DET_STAT_RATE_50HZ 0x9
> +#define XSDIRX_TS_DET_STAT_RATE_59_94HZ 0xa
> +#define XSDIRX_TS_DET_STAT_RATE_60HZ 0xb
> +
> +#define XSDIRX_EDH_STAT_EDH_AP_MASK BIT(0)
> +#define XSDIRX_EDH_STAT_EDH_FF_MASK BIT(1)
> +#define XSDIRX_EDH_STAT_EDH_ANC_MASK BIT(2)
> +#define XSDIRX_EDH_STAT_AP_FLAG_MASK GENMASK(8, 4)
> +#define XSDIRX_EDH_STAT_FF_FLAG_MASK GENMASK(13, 9)
> +#define XSDIRX_EDH_STAT_ANC_FLAG_MASK GENMASK(18, 14)
> +#define XSDIRX_EDH_STAT_PKT_FLAG_MASK GENMASK(22, 19)
> +
> +#define XSDIRX_EDH_ERRCNT_COUNT_MASK GENMASK(15, 0)
> +
> +#define XSDIRX_CRC_ERRCNT_COUNT_MASK GENMASK(31, 16)
> +#define XSDIRX_CRC_ERRCNT_DS_CRC_MASK GENMASK(15, 0)
> +
> +#define XSDIRX_VERSION_REV_MASK GENMASK(7, 0)
> +#define XSDIRX_VERSION_PATCHID_MASK GENMASK(11, 8)
> +#define XSDIRX_VERSION_VER_REV_MASK GENMASK(15, 12)
> +#define XSDIRX_VERSION_VER_MIN_MASK GENMASK(23, 16)
> +#define XSDIRX_VERSION_VER_MAJ_MASK GENMASK(31, 24)
> +
> +#define XSDIRX_SS_CONFIG_EDH_INCLUDED_MASK BIT(1)
> +
> +#define XSDIRX_STAT_SB_RX_TDATA_CHANGE_DONE_MASK BIT(0)
> +#define XSDIRX_STAT_SB_RX_TDATA_CHANGE_FAIL_MASK BIT(1)
> +#define XSDIRX_STAT_SB_RX_TDATA_GT_RESETDONE_MASK BIT(2)
> +#define XSDIRX_STAT_SB_RX_TDATA_GT_BITRATE_MASK BIT(3)
> +
> +#define XSDIRX_DEFAULT_WIDTH 1920
> +#define XSDIRX_DEFAULT_HEIGHT 1080
> +
> +#define XSDIRX_MAX_STR_LENGTH 16
This is not used. Please remove.
> +
> +#define XSDIRX_DEFAULT_VIDEO_LOCK_WINDOW 0x3000
Not sure if this macro is needed. The value can be used directly. Single
user macro without additional description may be removed. Please check.
> +
> +#define XSDIRX_MODE_HD_MASK 0x0
> +#define XSDIRX_MODE_SD_MASK 0x1
> +#define XSDIRX_MODE_3G_MASK 0x2
> +#define XSDIRX_MODE_6G_MASK 0x4
> +#define XSDIRX_MODE_12GI_MASK 0x5
> +#define XSDIRX_MODE_12GF_MASK 0x6
These are not masks, so _MASK better be removed from names.
> +
> +/* Maximum number of events per file handle. */
> +#define XSDIRX_MAX_EVENTS 8
> +
> +/* ST352 related macros */
> +#define XST352_PAYLOAD_BYTE1_MASK GENMASK(7, 0)
> +#define XST352_PAYLOAD_BYTE2_OFFSET 8
> +#define XST352_PAYLOAD_BYTE3_OFFSET 16
> +#define XST352_PAYLOAD_BYTE4_OFFSET 24
Last 3 are not used. Those may have become unused from using FIELD_GET().
Please remove.
> +
> +#define XST352_BYTE1_ST292_1x720L_1_5G 0x84
> +#define XST352_BYTE1_ST292_1x1080L_1_5G 0x85
> +#define XST352_BYTE1_ST425_2008_750L_3GB 0x88
> +#define XST352_BYTE1_ST425_2008_1125L_3GA 0x89
> +#define XST352_BYTE1_ST372_DL_3GB 0x8a
> +#define XST352_BYTE1_ST372_2x720L_3GB 0x8b
> +#define XST352_BYTE1_ST372_2x1080L_3GB 0x8c
> +#define XST352_BYTE1_ST2081_10_2160L_6G 0xc0
> +#define XST352_BYTE1_ST2081_10_2_1080L_6G 0xc1
> +#define XST352_BYTE1_ST2081_10_DL_2160L_6G 0xc2
> +#define XST352_BYTE1_ST2082_10_2160L_12G 0xce
> +
> +#define XST352_BYTE2_TS_TYPE_MASK BIT(15)
> +#define XST352_BYTE2_PIC_TYPE_MASK BIT(14)
> +#define XST352_BYTE2_TS_PIC_TYPE_INTERLACED 0
> +#define XST352_BYTE2_TS_PIC_TYPE_PROGRESSIVE 1
Not used. :) Please check and remove unneeded definitions.
> +
> +#define XST352_BYTE2_FPS_MASK GENMASK(11, 8)
> +#define XST352_BYTE2_FPS_24F 0x2
> +#define XST352_BYTE2_FPS_24 0x3
> +#define XST352_BYTE2_FPS_48F 0x4
> +#define XST352_BYTE2_FPS_25 0x5
> +#define XST352_BYTE2_FPS_30F 0x6
> +#define XST352_BYTE2_FPS_30 0x7
> +#define XST352_BYTE2_FPS_48 0x8
> +#define XST352_BYTE2_FPS_50 0x9
> +#define XST352_BYTE2_FPS_60F 0xa
> +#define XST352_BYTE2_FPS_60 0xb
> +/* Table 4 ST 2081-10:2015 */
> +#define XST352_BYTE2_FPS_96 0xc
> +#define XST352_BYTE2_FPS_100 0xd
> +#define XST352_BYTE2_FPS_120 0xe
> +#define XST352_BYTE2_FPS_120F 0xf
> +
> +#define XST352_BYTE3_ACT_LUMA_COUNT_MASK BIT(22)
> +
> +#define XST352_BYTE3_COLOR_FORMAT_MASK GENMASK(19, 16)
> +#define XST352_BYTE3_COLOR_FORMAT_422 0x0
> +#define XST352_BYTE3_COLOR_FORMAT_YUV444 0x1
> +#define XST352_BYTE3_COLOR_FORMAT_420 0x3
> +#define XST352_BYTE3_COLOR_FORMAT_GBR 0x2
> +
> +#define XST352_BYTE3_COLORIMETRY_MASK GENMASK(21, 20)
> +#define XST352_BYTE3_COLORIMETRY_BT709 0
> +#define XST352_BYTE3_COLORIMETRY_COLOR_VANC 1
> +#define XST352_BYTE3_COLORIMETRY_UHDTV 2
> +#define XST352_BYTE3_COLORIMETRY_UNKNOWN 3
> +
> +#define XST352_BYTE4_BIT_DEPTH_MASK GENMASK(25, 24)
> +#define XST352_BYTE4_BIT_DEPTH_10 0x1
> +#define XST352_BYTE4_BIT_DEPTH_12 0x2
> +
> +/* GT input clock for sdi_rx_clk */
> +#define CLK_INT 148500000UL
> +
> +#define XSDIRXSS_WIDTH_MIN 720
> +#define XSDIRXSS_WIDTH_MAX 4096
> +#define XSDIRXSS_HEIGHT_MIN 243
> +#define XSDIRXSS_HEIGHT_MAX 2160
> +#define XSDIRXSS_PIXELCLOCK_MIN 13500000
> +#define XSDIRXSS_PIXELCLOCK_MAX 594000000
> +
> +/**
> + * enum sdi_family_enc - SDI Transport Video Format Detected with Active Pixels
> + * @XSDIRX_SMPTE_ST_274: SMPTE ST 274 detected with AP 1920x1080
> + * @XSDIRX_SMPTE_ST_296: SMPTE ST 296 detected with AP 1280x720
> + * @XSDIRX_SMPTE_ST_2048_2: SMPTE ST 2048-2 detected with AP 2048x1080
> + * @XSDIRX_SMPTE_ST_295: SMPTE ST 295 detected with AP 1920x1080
> + * @XSDIRX_NTSC: NTSC encoding detected with AP 720x486
> + * @XSDIRX_PAL: PAL encoding detected with AP 720x576
> + * @XSDIRX_TS_UNKNOWN: Unknown SMPTE Transport family type
> + */
> +enum sdi_family_enc {
> + XSDIRX_SMPTE_ST_274 = 0,
> + XSDIRX_SMPTE_ST_296 = 1,
> + XSDIRX_SMPTE_ST_2048_2 = 2,
> + XSDIRX_SMPTE_ST_295 = 3,
> + XSDIRX_NTSC = 8,
> + XSDIRX_PAL = 9,
> + XSDIRX_TS_UNKNOWN = 15
> +};
> +
> +/**
> + * struct xsdirxss_state - SDI Rx Subsystem device structure
> + * @subdev: The v4l2 subdev structure
> + * @ctrl_handler: control handler
> + * @default_format: default V4L2 media bus format
> + * @pad: source media pad
> + * @dev: Platform structure
> + * @iomem: Base address of subsystem
> + * @clks: array of clocks
> + * @prev_is_frac: Previous clock is fractional or not flag
> + * @bpc: Bits per component, can be 10 or 12
> + * @mode: 3G/6G/12G mode
> + * @num_clks: number of clocks
> + * @include_edh: EDH processor presence
> + * @slock: spinlock to protect below members
> + * @format: Active V4L2 format detected
> + * @src_format: Active V4L2 format on source pad
> + * @frame_interval: Captures the frame rate
> + * @current_timings: DV timings from application
> + * @detected_timings_index: index of DV timings detected on incoming stream
> + * @vidlockwin: Video lock window value set by control
> + * @edhmask: EDH mask set by control
> + * @searchmask: Search mask set by control
> + * @streaming: Flag for storing streaming state
> + * @vidlocked: Flag indicating SDI Rx has locked onto video stream
> + * @ts_is_interlaced: Flag indicating Transport Stream is interlaced.
> + * @framer_enable: Flag for framer enabled or not set by control
> + *
> + * This structure contains the device driver related parameters
> + */
> +struct xsdirxss_state {
> + struct v4l2_subdev subdev;
> + struct v4l2_ctrl_handler ctrl_handler;
> + struct v4l2_mbus_framefmt default_format;
> + struct media_pad pad;
> + struct device *dev;
> + void __iomem *iomem;
> + struct clk_bulk_data *clks;
> + int prev_is_frac;
> + u32 bpc;
> + u32 mode;
> + unsigned int num_clks;
> + bool include_edh;
> +
> + /*
> + * This spinlock is used to protect the below members
> + * format, src_format, frame_interval, current_timings,
> + * detected_timings_index, vidlockwin, edhmask, searchmask,
> + * streaming, vidlocked, ts_is_interlaced, framer_enable
> + */
> + spinlock_t slock;
> + struct v4l2_mbus_framefmt format;
> + struct v4l2_mbus_framefmt src_format;
> + struct v4l2_fract frame_interval;
> + struct v4l2_dv_timings current_timings;
> + u32 detected_timings_index;
> + u32 vidlockwin;
> + u32 edhmask;
> + u16 searchmask;
> + bool streaming;
> + bool vidlocked;
> + bool ts_is_interlaced;
Use of bool in struct is not recommended. Not sure if it's doable with ones
getting values from other functions, but I beleive above 3 can change using
bit field or normal integer type.
> + bool framer_enable;
> +};
> +
> +/* List of clocks required by UHD-SDI Rx subsystem */
> +static const char * const xsdirxss_clks[] = {
> + "s_axi_aclk", "sdi_rx_clk", "video_out_clk",
> +};
This can move into probe() to reduce the scope.
> +
> +/* TODO - Add YUV 444/420 and RBG 10/12 bpc mbus formats here */
> +static const u32 xsdirxss_10bpc_mbus_fmts[] = {
> + MEDIA_BUS_FMT_UYVY10_1X20,
> +};
> +
> +static const u32 xsdirxss_12bpc_mbus_fmts[] = {
> + MEDIA_BUS_FMT_UYVY12_1X24,
> +};
> +
> +static const struct v4l2_dv_timings fmt_cap[] = {
> + V4L2_DV_BT_SDI_720X487I60,
> + V4L2_DV_BT_CEA_720X576I50,
> + V4L2_DV_BT_CEA_1280X720P24,
> + V4L2_DV_BT_CEA_1280X720P25,
> + V4L2_DV_BT_CEA_1280X720P30,
> + V4L2_DV_BT_CEA_1280X720P50,
> + V4L2_DV_BT_CEA_1280X720P60,
> + V4L2_DV_BT_CEA_1920X1080P24,
> + V4L2_DV_BT_CEA_1920X1080P30,
> + V4L2_DV_BT_CEA_1920X1080I50,
> + V4L2_DV_BT_CEA_1920X1080I60,
> + V4L2_DV_BT_CEA_1920X1080P48,
> + V4L2_DV_BT_CEA_1920X1080P50,
> + V4L2_DV_BT_CEA_1920X1080P60,
> + V4L2_DV_BT_CEA_3840X2160P24,
> + V4L2_DV_BT_CEA_3840X2160P30,
> + V4L2_DV_BT_CEA_3840X2160P48,
> + V4L2_DV_BT_CEA_3840X2160P50,
> + V4L2_DV_BT_CEA_3840X2160P60,
> + V4L2_DV_BT_CEA_4096X2160P24,
> + V4L2_DV_BT_CEA_4096X2160P25,
> + V4L2_DV_BT_CEA_4096X2160P30,
> + V4L2_DV_BT_CEA_4096X2160P48,
> + V4L2_DV_BT_CEA_4096X2160P50,
> + V4L2_DV_BT_CEA_4096X2160P60,
> +
> + XLNX_V4L2_DV_BT_2048X1080P24,
> + XLNX_V4L2_DV_BT_2048X1080P25,
> + XLNX_V4L2_DV_BT_2048X1080P30,
> + XLNX_V4L2_DV_BT_2048X1080I48,
> + XLNX_V4L2_DV_BT_2048X1080I50,
> + XLNX_V4L2_DV_BT_2048X1080I60,
> + XLNX_V4L2_DV_BT_2048X1080P48,
> + XLNX_V4L2_DV_BT_2048X1080P50,
> + XLNX_V4L2_DV_BT_2048X1080P60,
> + XLNX_V4L2_DV_BT_1920X1080I48,
> +};
> +
> +struct xsdirxss_dv_map {
> + u32 width;
> + u32 height;
> + u32 fps;
> + struct v4l2_dv_timings timing;
> +};
> +
> +static const struct xsdirxss_dv_map xsdirxss_dv_timings[] = {
> + /* SD - 720x487i60 */
> + { 720, 243, 30, V4L2_DV_BT_SDI_720X487I60 },
> + /* SD - 720x576i50 */
> + { 720, 288, 25, V4L2_DV_BT_CEA_720X576I50 },
> + /* HD - 1280x720p23.98 */
> + /* HD - 1280x720p24 */
> + { 1280, 720, 24, V4L2_DV_BT_CEA_1280X720P24 },
> + /* HD - 1280x720p25 */
> + { 1280, 720, 25, V4L2_DV_BT_CEA_1280X720P25 },
> + /* HD - 1280x720p29.97 */
> + /* HD - 1280x720p30 */
> + { 1280, 720, 30, V4L2_DV_BT_CEA_1280X720P30 },
> + /* HD - 1280x720p50 */
> + { 1280, 720, 50, V4L2_DV_BT_CEA_1280X720P50 },
> + /* HD - 1280x720p59.94 */
> + /* HD - 1280x720p60 */
> + { 1280, 720, 60, V4L2_DV_BT_CEA_1280X720P60 },
> + /* HD - 1920x1080p23.98 */
> + /* HD - 1920x1080p24 */
> + { 1920, 1080, 24, V4L2_DV_BT_CEA_1920X1080P24 },
> + /* HD - 1920x1080p25 */
> + { 1920, 1080, 25, V4L2_DV_BT_CEA_1920X1080P25 },
> + /* HD - 1920x1080p29.97 */
> + /* HD - 1920x1080p30 */
> + { 1920, 1080, 30, V4L2_DV_BT_CEA_1920X1080P30 },
> +
> + /* HD - 2048x1080p23.98 */
> + /* HD - 2048x1080p24 */
> + { 2048, 1080, 24, XLNX_V4L2_DV_BT_2048X1080P24 },
> + /* HD - 2048x1080p25 */
> + { 2048, 1080, 24, XLNX_V4L2_DV_BT_2048X1080P25 },
> + /* HD - 2048x1080p29.97 */
> + /* HD - 2048x1080p30 */
> + { 2048, 1080, 24, XLNX_V4L2_DV_BT_2048X1080P30 },
> + /* HD - 1920x1080i47.95 */
> + /* HD - 1920x1080i48 */
> + { 1920, 540, 24, XLNX_V4L2_DV_BT_1920X1080I48 },
> +
> + /* HD - 1920x1080i50 */
> + { 1920, 540, 25, V4L2_DV_BT_CEA_1920X1080I50 },
> + /* HD - 1920x1080i59.94 */
> + /* HD - 1920x1080i60 */
> + { 1920, 540, 30, V4L2_DV_BT_CEA_1920X1080I60 },
> +
> + /* HD - 2048x1080i47.95 */
> + /* HD - 2048x1080i48 */
> + { 2048, 540, 24, XLNX_V4L2_DV_BT_2048X1080I48 },
> + /* HD - 2048x1080i50 */
> + { 2048, 540, 25, XLNX_V4L2_DV_BT_2048X1080I50 },
> + /* HD - 2048x1080i59.94 */
> + /* HD - 2048x1080i60 */
> + { 2048, 540, 30, XLNX_V4L2_DV_BT_2048X1080I60 },
> + /* 3G - 1920x1080p47.95 */
> + /* 3G - 1920x1080p48 */
> + { 1920, 1080, 48, V4L2_DV_BT_CEA_1920X1080P48 },
> +
> + /* 3G - 1920x1080p50 148.5 */
> + { 1920, 1080, 50, V4L2_DV_BT_CEA_1920X1080P50 },
> + /* 3G - 1920x1080p59.94 148.5/1.001 */
> + /* 3G - 1920x1080p60 148.5 */
> + { 1920, 1080, 60, V4L2_DV_BT_CEA_1920X1080P60 },
> +
> + /* 3G - 2048x1080p47.95 */
> + /* 3G - 2048x1080p48 */
> + { 2048, 1080, 48, XLNX_V4L2_DV_BT_2048X1080P48 },
> + /* 3G - 2048x1080p50 */
> + { 2048, 1080, 50, XLNX_V4L2_DV_BT_2048X1080P50 },
> + /* 3G - 2048x1080p59.94 */
> + /* 3G - 2048x1080p60 */
> + { 2048, 1080, 60, XLNX_V4L2_DV_BT_2048X1080P60 },
> +
> + /* 6G - 3840X2160p23.98 */
> + /* 6G - 3840X2160p24 */
> + { 3840, 2160, 24, V4L2_DV_BT_CEA_3840X2160P24 },
> + /* 6G - 3840X2160p25 */
> + { 3840, 2160, 25, V4L2_DV_BT_CEA_3840X2160P25 },
> + /* 6G - 3840X2160p29.97 */
> + /* 6G - 3840X2160p30 */
> + { 3840, 2160, 30, V4L2_DV_BT_CEA_3840X2160P30 },
> + /* 6G - 4096X2160p23.98 */
> + /* 6G - 4096X2160p24 */
> + { 4096, 2160, 24, V4L2_DV_BT_CEA_4096X2160P24 },
> + /* 6G - 4096X2160p25 */
> + { 4096, 2160, 25, V4L2_DV_BT_CEA_4096X2160P25 },
> + /* 6G - 4096X2160p29.97 */
> + /* 6G - 4096X2160p30 */
> + { 4096, 2160, 30, V4L2_DV_BT_CEA_4096X2160P30 },
> + /* 12G - 3840X2160p47.95 */
> + /* 12G - 3840X2160p48 */
> + { 3840, 2160, 48, V4L2_DV_BT_CEA_3840X2160P48 },
> +
> + /* 12G - 3840X2160p50 */
> + { 3840, 2160, 50, V4L2_DV_BT_CEA_3840X2160P50 },
> + /* 12G - 3840X2160p59.94 */
> + /* 12G - 3840X2160p60 */
> + { 3840, 2160, 60, V4L2_DV_BT_CEA_3840X2160P60 },
> +
> + /* 12G - 4096X2160p47.95 */
> + /* 12G - 4096X2160p48 */
> + { 3840, 2160, 48, V4L2_DV_BT_CEA_4096X2160P48 },
> +
> + /* 12G - 4096X2160p50 */
> + { 4096, 2160, 50, V4L2_DV_BT_CEA_4096X2160P50 },
> + /* 12G - 4096X2160p59.94 */
> + /* 12G - 4096X2160p60 */
> + { 4096, 2160, 60, V4L2_DV_BT_CEA_4096X2160P60 },
> +};
> +
> +static const struct v4l2_dv_timings_cap xsdirxss_timings_cap = {
> + .type = V4L2_DV_BT_656_1120,
> + .pad = 0,
> + .reserved = { 0 },
> + V4L2_INIT_BT_TIMINGS(XSDIRXSS_WIDTH_MIN, XSDIRXSS_WIDTH_MAX,
> + XSDIRXSS_HEIGHT_MIN, XSDIRXSS_HEIGHT_MAX,
> + XSDIRXSS_PIXELCLOCK_MIN, XSDIRXSS_PIXELCLOCK_MAX,
> + V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_SDI,
> + V4L2_DV_BT_CAP_PROGRESSIVE
> + | V4L2_DV_BT_CAP_INTERLACED)
> +
> +};
> +
> +struct regmap {
> + const char *name;
> + u32 offset;
> +};
> +
> +static const struct regmap xsdirxss_regmap[] = {
> + { .name = "Reset Control", .offset = XSDIRX_RST_CTRL_REG },
> + { .name = "Module Control", .offset = XSDIRX_MDL_CTRL_REG },
> + { .name = "Interrupt Enable", .offset = XSDIRX_IER_REG },
> + { .name = "Global Interrupt Enable", .offset = XSDIRX_GLBL_IER_REG },
> + { .name = "ST352 Valid", .offset = XSDIRX_ST352_VALID_REG },
> + { .name = "ST352 DS1", .offset = XSDIRX_ST352_DS1_REG },
> + { .name = "ST352 DS2", .offset = XSDIRX_ST352_DS2_REG },
> + { .name = "ST352 DS3", .offset = XSDIRX_ST352_DS3_REG },
> + { .name = "ST352 DS4", .offset = XSDIRX_ST352_DS4_REG },
> + { .name = "ST352 DS5", .offset = XSDIRX_ST352_DS5_REG },
> + { .name = "ST352 DS6", .offset = XSDIRX_ST352_DS6_REG },
> + { .name = "ST352 DS7", .offset = XSDIRX_ST352_DS7_REG },
> + { .name = "ST352 DS8", .offset = XSDIRX_ST352_DS8_REG },
> + { .name = "ST352 DS9", .offset = XSDIRX_ST352_DS9_REG },
> + { .name = "ST352 DS10", .offset = XSDIRX_ST352_DS10_REG },
> + { .name = "ST352 DS11", .offset = XSDIRX_ST352_DS11_REG },
> + { .name = "ST352 DS12", .offset = XSDIRX_ST352_DS12_REG },
> + { .name = "ST352 DS13", .offset = XSDIRX_ST352_DS13_REG },
> + { .name = "ST352 DS14", .offset = XSDIRX_ST352_DS14_REG },
> + { .name = "ST352 DS15", .offset = XSDIRX_ST352_DS15_REG },
> + { .name = "ST352 DS16", .offset = XSDIRX_ST352_DS16_REG },
> + { .name = "Version", .offset = XSDIRX_VERSION_REG },
> + { .name = "Subsystem Config ", .offset = XSDIRX_SS_CONFIG_REG },
> + { .name = "Mode Detect", .offset = XSDIRX_MODE_DET_STAT_REG },
> + { .name = "Transport Stream Detect", .offset = XSDIRX_TS_DET_STAT_REG },
> + { .name = "EDH Status", .offset = XSDIRX_EDH_STAT_REG },
> + { .name = "EDH Error Count", .offset = XSDIRX_EDH_ERRCNT_EN_REG },
> + { .name = "CRC error indication", .offset = XSDIRX_CRC_ERRCNT_REG },
> + { .name = "Video Lock Window", .offset = XSDIRX_VID_LOCK_WINDOW_REG },
> +};
> +
> +static inline struct xsdirxss_state *
> +to_xsdirxssstate(struct v4l2_subdev *subdev)
> +{
> + return container_of(subdev, struct xsdirxss_state, subdev);
> +}
> +
> +/*
> + * Register related operations
> + */
> +static inline u32 xsdirxss_read(struct xsdirxss_state *xsdirxss, u32 addr)
> +{
> + return ioread32(xsdirxss->iomem + addr);
> +}
> +
> +static inline void xsdirxss_write(struct xsdirxss_state *xsdirxss, u32 addr,
> + u32 value)
> +{
> + iowrite32(value, xsdirxss->iomem + addr);
> +}
> +
> +static inline void xsdirxss_clr(struct xsdirxss_state *xsdirxss, u32 addr,
> + u32 clr)
> +{
> + xsdirxss_write(xsdirxss, addr, xsdirxss_read(xsdirxss, addr) & ~clr);
> +}
> +
> +static inline void xsdirxss_set(struct xsdirxss_state *xsdirxss, u32 addr,
> + u32 set)
> +{
> + xsdirxss_write(xsdirxss, addr, xsdirxss_read(xsdirxss, addr) | set);
> +}
> +
In my opinion, from here to
> +#define XSDIRX_CORE_DISABLE(state) xsdirxss_clr((state), XSDIRX_RST_CTRL_REG,\
> + XSDIRX_RST_CTRL_SS_EN_MASK)
> +
> +#define XSDIRX_CORE_ENABLE(state) xsdirxss_set((state), XSDIRX_RST_CTRL_REG,\
> + XSDIRX_RST_CTRL_SS_EN_MASK)
> +
> +#define XSDIRX_GLOBAL_INTR_ENABLE(state) \
> + xsdirxss_set((state), XSDIRX_GLBL_IER_REG, XSDIRX_GLBL_INTR_EN_MASK)
> +
> +#define XSDIRX_GLOBAL_INTR_DISABLE(state) \
> + xsdirxss_clr((state), XSDIRX_GLBL_IER_REG, XSDIRX_GLBL_INTR_EN_MASK)
here, inlining single liners or static inline would be better than above macros.
> +
> +static int xsdirx_set_modedetect(struct xsdirxss_state *state, u16 mask)
> +{
> + u32 val;
> + struct device *dev = state->dev;
> +
> + mask &= XSDIRX_DETECT_ALL_MODES;
> + if (!mask) {
> + dev_err(dev, "Invalid bit mask = 0x%08x\n", mask);
> + return -EINVAL;
> + }
> +
> + dev_dbg(dev, "mask = 0x%x\n", mask);
> +
> + val = xsdirxss_read(state, XSDIRX_MDL_CTRL_REG);
> + val &= ~XSDIRX_MDL_CTRL_MODE_DET_EN_MASK;
> + val &= ~XSDIRX_MDL_CTRL_MODE_AUTO_DET_MASK;
> + val &= ~XSDIRX_MDL_CTRL_FORCED_MODE_MASK;
> +
> + if (hweight16(mask) > 1) {
> + /* Multi mode detection as more than 1 bit set in mask */
> + dev_dbg(dev, "Detect multiple modes\n");
> +
> + if (mask & BIT(XSDIRX_MODE_SD_OFFSET))
> + val |= XSDIRX_MDL_CTRL_MODE_SD_EN_MASK;
> + if (mask & BIT(XSDIRX_MODE_HD_OFFSET))
> + val |= XSDIRX_MDL_CTRL_MODE_HD_EN_MASK;
> + /*
> + * There is only one bit in IP to detect 3G mode.
> + * So set it when 3GA or 3GB mask is set.
> + */
> + if (mask & (BIT(XSDIRX_MODE_3GA_OFFSET) |
> + BIT(XSDIRX_MODE_3GB_OFFSET)))
> + val |= XSDIRX_MDL_CTRL_MODE_3G_EN_MASK;
> + if (mask & BIT(XSDIRX_MODE_6G_OFFSET))
> + val |= XSDIRX_MDL_CTRL_MODE_6G_EN_MASK;
> + if (mask & BIT(XSDIRX_MODE_12GI_OFFSET))
> + val |= XSDIRX_MDL_CTRL_MODE_12GI_EN_MASK;
> + if (mask & BIT(XSDIRX_MODE_12GF_OFFSET))
> + val |= XSDIRX_MDL_CTRL_MODE_12GF_EN_MASK;
> +
> + val |= XSDIRX_MDL_CTRL_MODE_DET_EN_MASK;
> + } else {
> + /* Fixed Mode */
> + u32 forced_mode_mask;
> +
> + dev_dbg(dev, "Detect fixed mode\n");
> +
> + /* Find offset of first bit set */
> + switch (mask) {
> + case XSDIRX_MODE_SD_OFFSET:
> + forced_mode_mask = XSDIRX_MODE_SD_MASK;
> + break;
> + case XSDIRX_MODE_HD_OFFSET:
> + forced_mode_mask = XSDIRX_MODE_HD_MASK;
> + break;
> + /*
> + * There is only one bit in IP to detect 3G mode.
> + * So set it when 3GA or 3GB mask is set.
> + */
> + case XSDIRX_MODE_3GA_OFFSET:
> + case XSDIRX_MODE_3GB_OFFSET:
> + forced_mode_mask = XSDIRX_MODE_3G_MASK;
> + break;
> + case XSDIRX_MODE_6G_OFFSET:
> + forced_mode_mask = XSDIRX_MODE_6G_MASK;
> + break;
> + case XSDIRX_MODE_12GI_OFFSET:
> + forced_mode_mask = XSDIRX_MODE_12GI_MASK;
> + break;
> + case XSDIRX_MODE_12GF_OFFSET:
> + forced_mode_mask = XSDIRX_MODE_12GF_MASK;
> + break;
> + default:
> + dev_err(dev, "Invalid mask for fixed detect mode\n");
> + return -EINVAL;
> + }
> + dev_dbg(dev, "Forced Mode Mask : 0x%x\n",
> + forced_mode_mask);
> + val |= forced_mode_mask << XSDIRX_MDL_CTRL_FORCED_MODE_OFFSET;
> + }
> +
> + dev_dbg(dev, "Modes to be detected : sdi ctrl reg = 0x%08x\n",
> + val);
> + xsdirxss_write(state, XSDIRX_MDL_CTRL_REG, val);
> +
> + return 0;
> +}
> +
> +static void xsdirx_streamflow_control(struct xsdirxss_state *state, bool enable)
> +{
> + /* The sdi to native bridge is followed by native to axis4 bridge */
> + /*
> + * TODO - Enable YUV444/RBG format in the bridge based
> + * on BYTE3 color format.
> + * XSDIRX_RST_CTRL_BRIDGE_CH_FMT_YUV444
> + */
> + if (enable) {
> + xsdirxss_set(state, XSDIRX_RST_CTRL_REG,
> + XSDIRX_RST_CTRL_VIDIN_AXI4S_MOD_ENB_MASK);
> + xsdirxss_set(state, XSDIRX_RST_CTRL_REG,
> + XSDIRX_RST_CTRL_SDIRX_BRIDGE_ENB_MASK);
> + } else {
> + xsdirxss_clr(state, XSDIRX_RST_CTRL_REG,
> + XSDIRX_RST_CTRL_SDIRX_BRIDGE_ENB_MASK);
> + xsdirxss_clr(state, XSDIRX_RST_CTRL_REG,
> + XSDIRX_RST_CTRL_VIDIN_AXI4S_MOD_ENB_MASK);
> + }
> + state->streaming = enable;
> +}
> +
> +static void xsdirxss_get_framerate(struct v4l2_fract *frame_interval,
> + u32 framerate)
> +{
> + switch (framerate) {
> + case XSDIRX_TS_DET_STAT_RATE_23_98HZ:
> + frame_interval->numerator = 1001;
> + frame_interval->denominator = 24000;
> + break;
> + case XSDIRX_TS_DET_STAT_RATE_24HZ:
> + frame_interval->numerator = 1000;
> + frame_interval->denominator = 24000;
> + break;
> + case XSDIRX_TS_DET_STAT_RATE_25HZ:
> + frame_interval->numerator = 1000;
> + frame_interval->denominator = 25000;
> + break;
> + case XSDIRX_TS_DET_STAT_RATE_29_97HZ:
> + frame_interval->numerator = 1001;
> + frame_interval->denominator = 30000;
> + break;
> + case XSDIRX_TS_DET_STAT_RATE_30HZ:
> + frame_interval->numerator = 1000;
> + frame_interval->denominator = 30000;
> + break;
> + case XSDIRX_TS_DET_STAT_RATE_47_95HZ:
> + frame_interval->numerator = 1001;
> + frame_interval->denominator = 48000;
> + break;
> + case XSDIRX_TS_DET_STAT_RATE_48HZ:
> + frame_interval->numerator = 1000;
> + frame_interval->denominator = 48000;
> + break;
> + case XSDIRX_TS_DET_STAT_RATE_50HZ:
> + frame_interval->numerator = 1000;
> + frame_interval->denominator = 50000;
> + break;
> + case XSDIRX_TS_DET_STAT_RATE_59_94HZ:
> + frame_interval->numerator = 1001;
> + frame_interval->denominator = 60000;
> + break;
> + case XSDIRX_TS_DET_STAT_RATE_60HZ:
> + frame_interval->numerator = 1000;
> + frame_interval->denominator = 60000;
> + break;
> + default:
> + frame_interval->numerator = 1;
> + frame_interval->denominator = 1;
This shouldn't happen, so would it make sense to have an error here?
> + }
> +}
> +
> +static void xsdirxss_set_gtclk(struct xsdirxss_state *state)
> +{
> + struct clk *gtclk;
This variable is not needed. Up to you.
> + unsigned long clkrate;
> + int ret, is_frac;
> + u32 mode;
> +
> + mode = xsdirxss_read(state, XSDIRX_MODE_DET_STAT_REG);
> + mode &= XSDIRX_MODE_DET_STAT_RX_MODE_MASK;
> +
> + /*
> + * TODO: For now, don't change the clock rate for any mode except 12G.
> + * In future, configure gt clock for all modes and enable clock only
> + * when needed (stream on/off).
> + */
> + if (mode != XSDIRX_MODE_12GI_MASK && mode != XSDIRX_MODE_12GF_MASK)
> + return;
> +
> + /* When numerator is 1001 then frame rate is fractional else integer */
> + is_frac = state->frame_interval.numerator == 1001 ? 1 : 0;
> +
> + if (state->prev_is_frac == is_frac)
> + return;
> +
> + XSDIRX_GLOBAL_INTR_DISABLE(state);
> + xsdirxss_clr(state, XSDIRX_IER_REG, XSDIRX_INTR_ALL_MASK);
> + XSDIRX_CORE_DISABLE(state);
> +
> + /* get sdi_rx_clk */
I'd remove this comment,
> + gtclk = state->clks[1].clk;
> +
> + /* calculate clkrate */
and this. Up to you.
> + if (!is_frac)
> + clkrate = CLK_INT;
> + else
> + clkrate = (CLK_INT * 1000) / 1001;
> +
> + ret = clk_set_rate(gtclk, clkrate);
> + if (ret)
> + dev_err(state->dev, "failed to set clk rate = %d\n", ret);
> +
> + state->prev_is_frac = is_frac;
> + clkrate = clk_get_rate(gtclk);
Shouldn't the returned rate be checked and warn if diff is too much? Above
changes the rate by 0.1% which means the rate should be quite precise. So it
better be checked.
> +
> + dev_dbg(state->dev, "clkrate = %lu is_frac = %d\n",
> + clkrate, is_frac);
> +
> + if (state->framer_enable) {
> + xsdirxss_set(state, XSDIRX_MDL_CTRL_REG,
> + XSDIRX_MDL_CTRL_FRM_EN_MASK);
> + } else {
> + xsdirxss_clr(state, XSDIRX_MDL_CTRL_REG,
> + XSDIRX_MDL_CTRL_FRM_EN_MASK);
> + }
> + xsdirxss_write(state, XSDIRX_EDH_ERRCNT_EN_REG,
> + state->edhmask & XSDIRX_EDH_ALLERR_MASK);
> + xsdirxss_write(state, XSDIRX_VID_LOCK_WINDOW_REG, state->vidlocked);
> + xsdirx_set_modedetect(state, state->searchmask);
> + XSDIRX_CORE_ENABLE(state);
> + xsdirxss_set(state, XSDIRX_IER_REG, XSDIRX_INTR_ALL_MASK);
> + XSDIRX_GLOBAL_INTR_ENABLE(state);
> +}
> +
> +/**
> + * xsdirx_get_stream_properties - Get SDI Rx stream properties
> + * @state: pointer to driver state
> + *
> + * This function decodes the stream's ST352 payload (if available) to get
> + * stream properties like width, height, picture type (interlaced/progressive),
> + * etc.
> + *
> + * Return: 0 for success else errors
> + */
> +static int xsdirx_get_stream_properties(struct xsdirxss_state *state)
> +{
> + struct device *dev = state->dev;
> + u32 mode, payload = 0, val, family, valid, tscan;
> + u8 byte1 = 0, active_luma = 0, pic_type = 0, framerate = 0;
> + u8 sampling = XST352_BYTE3_COLOR_FORMAT_422;
> + struct v4l2_mbus_framefmt *format = &state->format;
> + u32 bpc = XST352_BYTE4_BIT_DEPTH_10;
> + u32 colorimetry = XST352_BYTE3_COLORIMETRY_BT709;
> +
> + mode = xsdirxss_read(state, XSDIRX_MODE_DET_STAT_REG);
> + mode &= XSDIRX_MODE_DET_STAT_RX_MODE_MASK;
> +
> + valid = xsdirxss_read(state, XSDIRX_ST352_VALID_REG);
> +
> + if (mode >= XSDIRX_MODE_3G_MASK && !valid) {
> + dev_err(dev, "No valid ST352 payload present even for 3G mode and above\n");
> + return -EINVAL;
> + }
> +
> + val = xsdirxss_read(state, XSDIRX_TS_DET_STAT_REG);
> + if (valid & XSDIRX_ST352_VALID_DS1_MASK) {
> + payload = xsdirxss_read(state, XSDIRX_ST352_DS1_REG);
> + byte1 = FIELD_GET(XST352_PAYLOAD_BYTE1_MASK, payload);
> + active_luma = FIELD_GET(XST352_BYTE3_ACT_LUMA_COUNT_MASK,
> + payload);
> + pic_type = FIELD_GET(XST352_BYTE2_PIC_TYPE_MASK, payload);
> + framerate = FIELD_GET(XST352_BYTE2_FPS_MASK, payload);
> + tscan = FIELD_GET(XST352_BYTE2_TS_TYPE_MASK, payload);
> + sampling = FIELD_GET(XST352_BYTE3_COLOR_FORMAT_MASK, payload);
> + bpc = FIELD_GET(XST352_BYTE4_BIT_DEPTH_MASK, payload);
> + colorimetry = FIELD_GET(XST352_BYTE3_COLORIMETRY_MASK, payload);
> + } else {
> + dev_dbg(dev, "No ST352 payload available : Mode = %d\n", mode);
> + framerate = FIELD_GET(XSDIRX_TS_DET_STAT_RATE_MASK, val);
> + tscan = FIELD_GET(XSDIRX_TS_DET_STAT_SCAN_MASK, val);
> + }
> +
> + if ((bpc == XST352_BYTE4_BIT_DEPTH_10 && state->bpc != 10) ||
> + (bpc == XST352_BYTE4_BIT_DEPTH_12 && state->bpc != 12)) {
> + dev_dbg(dev, "Bit depth not supported. bpc = %d state->bpc = %d\n",
> + bpc, state->bpc);
> + return -EINVAL;
> + }
> +
> + family = FIELD_GET(XSDIRX_TS_DET_STAT_FAMILY_MASK, val);
> + state->ts_is_interlaced = tscan ? false : true;
> +
> + dev_dbg(dev, "ts_is_interlaced = %d, family = %d\n",
> + state->ts_is_interlaced, family);
> +
> + switch (mode) {
> + case XSDIRX_MODE_HD_MASK:
> + if (!valid) {
> + /* No payload obtained */
> + dev_dbg(dev, "frame rate : %d, tscan = %d\n",
> + framerate, tscan);
> + /*
> + * NOTE : A progressive segmented frame pSF will be
> + * reported incorrectly as Interlaced as we rely on IP's
> + * transport scan locked bit.
> + */
> + dev_warn(dev, "pSF will be incorrectly reported as Interlaced\n");
> +
> + switch (framerate) {
> + case XSDIRX_TS_DET_STAT_RATE_23_98HZ:
> + case XSDIRX_TS_DET_STAT_RATE_24HZ:
> + case XSDIRX_TS_DET_STAT_RATE_25HZ:
> + case XSDIRX_TS_DET_STAT_RATE_29_97HZ:
> + case XSDIRX_TS_DET_STAT_RATE_30HZ:
> + if (family == XSDIRX_SMPTE_ST_296) {
> + format->width = 1280;
> + format->height = 720;
> + format->field = V4L2_FIELD_NONE;
> + } else if (family == XSDIRX_SMPTE_ST_2048_2) {
> + format->width = 2048;
> + format->height = 1080;
> + if (tscan)
> + format->field = V4L2_FIELD_NONE;
> + else
> + format->field =
> + V4L2_FIELD_ALTERNATE;
> + } else {
> + format->width = 1920;
> + format->height = 1080;
> + if (tscan)
> + format->field = V4L2_FIELD_NONE;
> + else
> + format->field =
> + V4L2_FIELD_ALTERNATE;
> + }
> + break;
> + case XSDIRX_TS_DET_STAT_RATE_50HZ:
> + case XSDIRX_TS_DET_STAT_RATE_59_94HZ:
> + case XSDIRX_TS_DET_STAT_RATE_60HZ:
> + if (family == XSDIRX_SMPTE_ST_274) {
> + format->width = 1920;
> + format->height = 1080;
> + } else {
> + format->width = 1280;
> + format->height = 720;
> + }
> + format->field = V4L2_FIELD_NONE;
> + break;
> + default:
> + format->width = 1920;
> + format->height = 1080;
> + format->field = V4L2_FIELD_NONE;
> + }
> + } else {
> + dev_dbg(dev, "Got the payload\n");
> + switch (byte1) {
> + case XST352_BYTE1_ST292_1x720L_1_5G:
> + /* SMPTE ST 292-1 for 720 line payloads */
> + format->width = 1280;
> + format->height = 720;
> + break;
> + case XST352_BYTE1_ST292_1x1080L_1_5G:
> + /* SMPTE ST 292-1 for 1080 line payloads */
> + format->height = 1080;
> + if (active_luma)
> + format->width = 2048;
> + else
> + format->width = 1920;
> + break;
> + default:
> + dev_dbg(dev, "Unknown HD Mode SMPTE standard\n");
> + return -EINVAL;
> + }
> + }
> + break;
> + case XSDIRX_MODE_SD_MASK:
> + format->field = V4L2_FIELD_ALTERNATE;
> +
> + switch (family) {
> + case XSDIRX_NTSC:
> + format->width = 720;
> + format->height = 486;
> + break;
> + case XSDIRX_PAL:
> + format->width = 720;
> + format->height = 576;
> + break;
> + default:
> + dev_dbg(dev, "Unknown SD Mode SMPTE standard\n");
> + return -EINVAL;
> + }
> + break;
> + case XSDIRX_MODE_3G_MASK:
> + switch (byte1) {
> + case XST352_BYTE1_ST425_2008_750L_3GB:
> + /* Sec 4.1.6.1 SMPTE 425-2008 */
> + case XST352_BYTE1_ST372_2x720L_3GB:
> + /* Table 13 SMPTE 425-2008 */
> + format->width = 1280;
> + format->height = 720;
> + break;
> + case XST352_BYTE1_ST425_2008_1125L_3GA:
> + /* ST352 Table SMPTE 425-1 */
> + case XST352_BYTE1_ST372_DL_3GB:
> + /* Table 13 SMPTE 425-2008 */
> + case XST352_BYTE1_ST372_2x1080L_3GB:
> + /* Table 13 SMPTE 425-2008 */
> + format->height = 1080;
> + if (active_luma)
> + format->width = 2048;
> + else
> + format->width = 1920;
> + break;
> + default:
> + dev_dbg(dev, "Unknown 3G Mode SMPTE standard\n");
> + return -EINVAL;
> + }
> + break;
> + case XSDIRX_MODE_6G_MASK:
> + switch (byte1) {
> + case XST352_BYTE1_ST2081_10_DL_2160L_6G:
> + /* Dual link 6G */
> + case XST352_BYTE1_ST2081_10_2160L_6G:
> + /* Table 3 SMPTE ST 2081-10 */
> + format->height = 2160;
> + if (active_luma)
> + format->width = 4096;
> + else
> + format->width = 3840;
> + break;
> + case XST352_BYTE1_ST2081_10_2_1080L_6G:
> + format->height = 1080;
> + if (active_luma)
> + format->width = 2048;
> + else
> + format->width = 1920;
> + break;
> + default:
> + dev_dbg(dev, "Unknown 6G Mode SMPTE standard\n");
> + return -EINVAL;
> + }
> + break;
> + case XSDIRX_MODE_12GI_MASK:
> + case XSDIRX_MODE_12GF_MASK:
> + switch (byte1) {
> + case XST352_BYTE1_ST2082_10_2160L_12G:
> + /* Section 4.3.1 SMPTE ST 2082-10 */
> + format->height = 2160;
> + if (active_luma)
> + format->width = 4096;
> + else
> + format->width = 3840;
> + break;
> + default:
> + dev_dbg(dev, "Unknown 12G Mode SMPTE standard\n");
> + return -EINVAL;
> + }
> + break;
> + default:
> + dev_err(dev, "Invalid Mode\n");
> + return -EINVAL;
> + }
> +
> + if (valid) {
> + if (pic_type)
> + format->field = V4L2_FIELD_NONE;
> + else
> + format->field = V4L2_FIELD_ALTERNATE;
> +
> + if (format->height == 1080 && pic_type && !tscan)
> + format->field = V4L2_FIELD_ALTERNATE;
> +
> + /*
> + * In 3GB DL pSF mode the video is similar to interlaced.
> + * So though it is a progressive video, its transport is
> + * interlaced and is sent as two width x (height/2) buffers.
> + */
> + if (byte1 == XST352_BYTE1_ST372_DL_3GB) {
> + if (state->ts_is_interlaced)
> + format->field = V4L2_FIELD_ALTERNATE;
> + else
> + format->field = V4L2_FIELD_NONE;
> + }
> + }
> +
> + if (format->field == V4L2_FIELD_ALTERNATE)
> + format->height = format->height / 2;
> +
> + switch (sampling) {
> + case XST352_BYTE3_COLOR_FORMAT_422:
> + if (state->bpc == 10)
> + format->code = MEDIA_BUS_FMT_UYVY10_1X20;
> + else
> + format->code = MEDIA_BUS_FMT_UYVY12_1X24;
> + break;
> + case XST352_BYTE3_COLOR_FORMAT_420:
> + case XST352_BYTE3_COLOR_FORMAT_YUV444:
> + case XST352_BYTE3_COLOR_FORMAT_GBR:
> + format->code = 0;
> + dev_dbg(dev, "No corresponding media bus formats\n");
> + break;
> + default:
> + dev_err(dev, "Unsupported color format : %d\n", sampling);
> + return -EINVAL;
> + }
> +
> + /* Refer Table 3 SMPTE ST 2081-10:2018 */
> + switch (colorimetry) {
> + case XST352_BYTE3_COLORIMETRY_BT709:
> + format->colorspace = V4L2_COLORSPACE_REC709;
> + break;
> + /* When HDR support is added UHDTV will have BT2020 colorspace */
> + case XST352_BYTE3_COLORIMETRY_UHDTV:
> + case XST352_BYTE3_COLORIMETRY_COLOR_VANC:
> + case XST352_BYTE3_COLORIMETRY_UNKNOWN:
> + default:
> + dev_err(dev, "Unknown colorimetry : %d\n", colorimetry);
> + return -EINVAL;
> + }
> +
> + xsdirxss_get_framerate(&state->frame_interval, framerate);
> +
> + dev_dbg(dev, "Stream width = %d height = %d Field = %d payload = 0x%08x ts = 0x%08x\n",
> + format->width, format->height, format->field, payload, val);
> + dev_dbg(dev, "frame rate numerator = %d denominator = %d\n",
> + state->frame_interval.numerator,
> + state->frame_interval.denominator);
> + dev_dbg(dev, "Stream code = 0x%x\n", format->code);
> + return 0;
> +}
> +
> +/**
> + * xsdirxss_irq_handler - Interrupt handler for SDI Rx
> + * @irq: IRQ number
> + * @dev_id: Pointer to device state
> + *
> + * The SDI Rx interrupts are cleared by writing 1 to corresponding bit.
> + *
> + * Return: IRQ_HANDLED after handling interrupts
> + */
> +static irqreturn_t xsdirxss_irq_handler(int irq, void *dev_id)
> +{
> + struct xsdirxss_state *state = (struct xsdirxss_state *)dev_id;
> + struct device *dev = state->dev;
> + u32 status;
> +
> + status = xsdirxss_read(state, XSDIRX_ISR_REG);
> + xsdirxss_write(state, XSDIRX_ISR_REG, status);
This can be done after check below, so IO is skipped when not needed.
> + dev_dbg(dev, "interrupt status = 0x%08x\n", status);
> +
> + if (!status)
> + return IRQ_NONE;
> +
> + if (status & XSDIRX_INTR_VIDLOCK_MASK ||
> + status & XSDIRX_INTR_VIDUNLOCK_MASK) {
> + u32 val1, val2;
> + struct v4l2_event event = { 0 };
> + unsigned long flags;
> +
> + dev_dbg(dev, "video lock/unlock interrupt\n");
> +
> + spin_lock_irqsave(&state->slock, flags);
> + xsdirx_streamflow_control(state, false);
> +
> + val1 = xsdirxss_read(state, XSDIRX_MODE_DET_STAT_REG);
> + val2 = xsdirxss_read(state, XSDIRX_TS_DET_STAT_REG);
> +
> + if ((val1 & XSDIRX_MODE_DET_STAT_MODE_LOCK_MASK) &&
> + (val2 & XSDIRX_TS_DET_STAT_LOCKED_MASK)) {
> + u32 mask = XSDIRX_RST_CTRL_RST_CRC_ERRCNT_MASK |
> + XSDIRX_RST_CTRL_RST_EDH_ERRCNT_MASK;
> +
> + dev_dbg(dev, "video lock interrupt\n");
> +
> + xsdirxss_set(state, XSDIRX_RST_CTRL_REG, mask);
> + xsdirxss_clr(state, XSDIRX_RST_CTRL_REG, mask);
> +
> + val1 = xsdirxss_read(state, XSDIRX_ST352_VALID_REG);
> + val2 = xsdirxss_read(state, XSDIRX_ST352_DS1_REG);
> +
> + dev_dbg(dev, "valid st352 mask = 0x%08x\n", val1);
> + dev_dbg(dev, "st352 payload = 0x%08x\n", val2);
> +
> + if (!xsdirx_get_stream_properties(state)) {
> + state->vidlocked = true;
> + xsdirxss_set_gtclk(state);
> + } else {
> + dev_err(dev, "Unable to get stream properties!\n");
> + state->vidlocked = false;
> + }
> + } else {
> + dev_dbg(dev, "video unlock interrupt\n");
> + state->vidlocked = false;
> + }
> + spin_unlock_irqrestore(&state->slock, flags);
> +
> + event.type = V4L2_EVENT_SOURCE_CHANGE;
> + event.u.src_change.changes = V4L2_EVENT_SRC_CH_RESOLUTION;
> + v4l2_subdev_notify_event(&state->subdev, &event);
> + }
> +
> + if (status & (XSDIRX_INTR_UNDERFLOW_MASK | XSDIRX_INTR_OVERFLOW_MASK)) {
> + struct v4l2_event event = { 0 };
> +
> + dev_dbg(dev, "Video in to AXI4 Stream core under/overflow interrupt\n");
> +
> + event.type = V4L2_EVENT_XILINX_SDIRX_UND_OVR_FLOW;
> + if (status & XSDIRX_INTR_UNDERFLOW_MASK)
> + event.u.data[0] = XILINX_SDIRX_UNDERFLOW_EVENT;
> + if (status & XSDIRX_INTR_OVERFLOW_MASK)
> + event.u.data[0] = XILINX_SDIRX_OVERFLOW_EVENT;
Should be ORed?
> +
> + v4l2_subdev_notify_event(&state->subdev, &event);
> + }
> + return IRQ_HANDLED;
> +}
> +
> +/**
> + * xsdirxss_subscribe_event - Subscribe to video lock and unlock event
> + * @sd: V4L2 Sub device
> + * @fh: V4L2 File Handle
> + * @sub: Subcribe event structure
> + *
> + * Return: 0 on success, errors otherwise
> + */
> +static int xsdirxss_subscribe_event(struct v4l2_subdev *sd,
> + struct v4l2_fh *fh,
> + struct v4l2_event_subscription *sub)
> +{
> + int ret;
> + struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
> +
> + dev_dbg(xsdirxss->dev, "Event subscribed : 0x%08x\n", sub->type);
> + switch (sub->type) {
> + case V4L2_EVENT_XILINX_SDIRX_UND_OVR_FLOW:
> + ret = v4l2_event_subscribe(fh, sub, XSDIRX_MAX_EVENTS, NULL);
> + break;
> + case V4L2_EVENT_SOURCE_CHANGE:
> + ret = v4l2_src_change_event_subscribe(fh, sub);
> + break;
> + default:
> + ret = v4l2_ctrl_subscribe_event(fh, sub);
> + }
> + return ret;
> +}
> +
> +/**
> + * xsdirxss_s_ctrl - This is used to set the Xilinx SDI Rx V4L2 controls
> + * @ctrl: V4L2 control to be set
> + *
> + * This function is used to set the V4L2 controls for the Xilinx SDI Rx
> + * Subsystem.
> + *
> + * Return: 0 on success, errors otherwise
> + */
> +static int xsdirxss_s_ctrl(struct v4l2_ctrl *ctrl)
> +{
> + int ret = 0;
No need to initialize this.
> + struct xsdirxss_state *xsdirxss =
> + container_of(ctrl->handler, struct xsdirxss_state,
> + ctrl_handler);
> + struct device *dev = xsdirxss->dev;
> + unsigned long flags;
> +
> + dev_dbg(dev, "set ctrl id = 0x%08x val = 0x%08x\n",
> + ctrl->id, ctrl->val);
> +
> + spin_lock_irqsave(&xsdirxss->slock, flags);
> +
> + if (xsdirxss->streaming) {
> + spin_unlock_irqrestore(&xsdirxss->slock, flags);
> + dev_err(dev, "Cannot set controls while streaming\n");
> + return -EINVAL;
> + }
> +
> + XSDIRX_CORE_DISABLE(xsdirxss);
> + switch (ctrl->id) {
> + case V4L2_CID_XILINX_SDIRX_FRAMER:
> + xsdirxss->framer_enable = ctrl->val;
> + if (xsdirxss->framer_enable) {
> + xsdirxss_set(xsdirxss, XSDIRX_MDL_CTRL_REG,
> + XSDIRX_MDL_CTRL_FRM_EN_MASK);
> + } else {
> + xsdirxss_clr(xsdirxss, XSDIRX_MDL_CTRL_REG,
> + XSDIRX_MDL_CTRL_FRM_EN_MASK);
> + }
> + break;
> + case V4L2_CID_XILINX_SDIRX_VIDLOCK_WINDOW:
> + /*
> + * The video lock window is the amount of time for which the
> + * the mode and transport stream should be locked to get the
> + * video lock interrupt.
> + */
> + xsdirxss->vidlockwin = ctrl->val;
> + xsdirxss_write(xsdirxss, XSDIRX_VID_LOCK_WINDOW_REG,
> + xsdirxss->vidlockwin);
> + break;
> + case V4L2_CID_XILINX_SDIRX_EDH_ERROR_SOURCES:
> + xsdirxss->edhmask = ctrl->val & XSDIRX_EDH_ALLERR_MASK;
> + xsdirxss_write(xsdirxss, XSDIRX_EDH_ERRCNT_EN_REG,
> + xsdirxss->edhmask);
> + break;
> + case V4L2_CID_XILINX_SDIRX_SEARCH_MODES:
> + if (!ctrl->val) {
> + spin_unlock_irqrestore(&xsdirxss->slock, flags);
> + dev_err(dev, "Select at least one mode!\n");
> + return -EINVAL;
> + }
> +
> + if (xsdirxss->mode == XSDI_STD_3G) {
> + dev_dbg(dev, "Upto 3G supported\n");
> + ctrl->val &= ~(BIT(XSDIRX_MODE_6G_OFFSET) |
> + BIT(XSDIRX_MODE_12GI_OFFSET) |
> + BIT(XSDIRX_MODE_12GF_OFFSET));
> + }
> +
> + if (xsdirxss->mode == XSDI_STD_6G) {
> + dev_dbg(dev, "Upto 6G supported\n");
> + ctrl->val &= ~(BIT(XSDIRX_MODE_12GI_OFFSET) |
> + BIT(XSDIRX_MODE_12GF_OFFSET));
> + }
> +
> + ret = xsdirx_set_modedetect(xsdirxss, ctrl->val);
> + if (!ret)
> + xsdirxss->searchmask = ctrl->val;
> + break;
> + default:
> + ret = -EINVAL;
> + break;
> + }
> + XSDIRX_CORE_ENABLE(xsdirxss);
> +
> + spin_unlock_irqrestore(&xsdirxss->slock, flags);
> + return ret;
> +}
> +
> +/**
> + * xsdirxss_g_volatile_ctrl - get the Xilinx SDI Rx controls
> + * @ctrl: Pointer to V4L2 control
> + *
> + * Return: 0 on success, errors otherwise
> + */
> +static int xsdirxss_g_volatile_ctrl(struct v4l2_ctrl *ctrl)
> +{
> + u32 val;
> + struct xsdirxss_state *xsdirxss =
> + container_of(ctrl->handler,
> + struct xsdirxss_state, ctrl_handler);
> + struct device *dev = xsdirxss->dev;
> + unsigned long flags;
> +
> + spin_lock_irqsave(&xsdirxss->slock, flags);
> + if (!xsdirxss->vidlocked) {
> + spin_unlock_irqrestore(&xsdirxss->slock, flags);
> + dev_err(dev, "Can't get values when video not locked!\n");
> + return -EINVAL;
> + }
> + switch (ctrl->id) {
> + case V4L2_CID_XILINX_SDIRX_MODE_DETECT:
> + val = xsdirxss_read(xsdirxss, XSDIRX_MODE_DET_STAT_REG);
> + val &= XSDIRX_MODE_DET_STAT_RX_MODE_MASK;
> +
> + switch (val) {
> + case XSDIRX_MODE_SD_MASK:
> + ctrl->val = XSDIRX_MODE_SD_OFFSET;
> + break;
> + case XSDIRX_MODE_HD_MASK:
> + ctrl->val = XSDIRX_MODE_HD_OFFSET;
> + break;
> + case XSDIRX_MODE_3G_MASK:
> + val = xsdirxss_read(xsdirxss, XSDIRX_MODE_DET_STAT_REG);
> + val &= XSDIRX_MODE_DET_STAT_LVLB_3G_MASK;
> + ctrl->val = val ? XSDIRX_MODE_3GB_OFFSET :
> + XSDIRX_MODE_3GA_OFFSET;
> + break;
> + case XSDIRX_MODE_6G_MASK:
> + ctrl->val = XSDIRX_MODE_6G_OFFSET;
> + break;
> + case XSDIRX_MODE_12GI_MASK:
> + ctrl->val = XSDIRX_MODE_12GI_OFFSET;
> + break;
> + case XSDIRX_MODE_12GF_MASK:
> + ctrl->val = XSDIRX_MODE_12GF_OFFSET;
> + break;
> + }
> + break;
> + case V4L2_CID_XILINX_SDIRX_CRC:
> + ctrl->val = xsdirxss_read(xsdirxss, XSDIRX_CRC_ERRCNT_REG);
> + xsdirxss_write(xsdirxss, XSDIRX_CRC_ERRCNT_REG, 0xffff);
> + break;
> + case V4L2_CID_XILINX_SDIRX_EDH_ERRCNT:
> + val = xsdirxss_read(xsdirxss, XSDIRX_MODE_DET_STAT_REG);
> + val &= XSDIRX_MODE_DET_STAT_RX_MODE_MASK;
> + if (val == XSDIRX_MODE_SD_MASK) {
> + ctrl->val = xsdirxss_read(xsdirxss,
> + XSDIRX_EDH_ERRCNT_REG);
> + } else {
> + spin_unlock_irqrestore(&xsdirxss->slock, flags);
> + dev_dbg(dev, "%d - not in SD mode\n", ctrl->id);
> + return -EINVAL;
> + }
> + break;
> + case V4L2_CID_XILINX_SDIRX_EDH_STATUS:
> + val = xsdirxss_read(xsdirxss, XSDIRX_MODE_DET_STAT_REG);
> + val &= XSDIRX_MODE_DET_STAT_RX_MODE_MASK;
> + if (val == XSDIRX_MODE_SD_MASK) {
> + ctrl->val = xsdirxss_read(xsdirxss,
> + XSDIRX_EDH_STAT_REG);
> + } else {
> + spin_unlock_irqrestore(&xsdirxss->slock, flags);
> + dev_dbg(dev, "%d - not in SD mode\n", ctrl->id);
> + return -EINVAL;
> + }
> + break;
> + case V4L2_CID_XILINX_SDIRX_TS_IS_INTERLACED:
> + ctrl->val = xsdirxss->ts_is_interlaced;
> + break;
> + default:
> + spin_unlock_irqrestore(&xsdirxss->slock, flags);
> + dev_err(dev, "Get Invalid control id 0x%0x\n", ctrl->id);
> + return -EINVAL;
> + }
> +
> + spin_unlock_irqrestore(&xsdirxss->slock, flags);
> + return 0;
> +}
> +
> +/**
> + * xsdirxss_log_status - Logs the status of the SDI Rx Subsystem
> + * @sd: Pointer to V4L2 subdevice structure
> + *
> + * This function prints the current status of Xilinx SDI Rx Subsystem
> + *
> + * Return: 0 on success
> + */
> +static int xsdirxss_log_status(struct v4l2_subdev *sd)
> +{
> + struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
> + u32 i;
> +
> + v4l2_info(sd, "***** SDI Rx subsystem reg dump start *****\n");
> + v4l2_info(sd, "No : Register Name : Value\n");
> + for (i = 0; i < ARRAY_SIZE(xsdirxss_regmap); i++) {
> + v4l2_info(sd, "%02d : %s register : 0x%08x\n", i,
> + xsdirxss_regmap[i].name,
> + xsdirxss_read(xsdirxss, xsdirxss_regmap[i].offset));
> + }
> + v4l2_info(sd, "***** SDI Rx subsystem reg dump end *****\n");
> +
> + v4l2_ctrl_subdev_log_status(sd);
> +
> + return 0;
> +}
> +
> +/**
> + * xsdirxss_g_frame_interval - Get the frame interval
> + * @sd: V4L2 Sub device
> + * @fi: Pointer to V4l2 Sub device frame interval structure
> + *
> + * This function is used to get the frame interval.
> + * The frame rate can be integral or fractional.
> + * Integral frame rate e.g. numerator = 1000, denominator = 24000 => 24 fps
> + * Fractional frame rate e.g. numerator = 1001, denominator = 24000 => 23.97 fps
> + *
> + * Return: 0 on success
> + */
> +static int xsdirxss_g_frame_interval(struct v4l2_subdev *sd,
> + struct v4l2_subdev_frame_interval *fi)
> +{
> + struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
> + unsigned long flags;
> +
> + if (!xsdirxss->vidlocked) {
Shouldn't this be accessed under spinlock?
> + dev_err(xsdirxss->dev, "Video not locked!\n");
> + return -EINVAL;
> + }
> +
> + spin_lock_irqsave(&xsdirxss->slock, flags);
> + fi->interval = xsdirxss->frame_interval;
> + spin_unlock_irqrestore(&xsdirxss->slock, flags);
> +
> + dev_dbg(xsdirxss->dev, "frame rate numerator = %d denominator = %d\n",
> + xsdirxss->frame_interval.numerator,
> + xsdirxss->frame_interval.denominator);
This too.
> + return 0;
> +}
> +
> +/**
> + * xsdirxss_s_stream - It is used to start/stop the streaming.
> + * @sd: V4L2 Sub device
> + * @enable: Flag (True / False)
> + *
> + * This function controls the start or stop of streaming for the
> + * Xilinx SDI Rx Subsystem.
> + *
> + * Return: 0 on success, errors otherwise
> + */
> +static int xsdirxss_s_stream(struct v4l2_subdev *sd, int enable)
> +{
> + struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
> + struct device *dev = xsdirxss->dev;
> + unsigned long flags;
> +
> + spin_lock_irqsave(&xsdirxss->slock, flags);
> + if (enable == xsdirxss->streaming) {
> + spin_unlock_irqrestore(&xsdirxss->slock, flags);
> + dev_dbg(dev, "already in same streaming state as requested\n");
> + return 0;
> + }
> +
> + if (enable) {
> + if (!xsdirxss->vidlocked) {
> + spin_unlock_irqrestore(&xsdirxss->slock, flags);
> + dev_err(dev, "Video is not locked\n");
> + return -EINVAL;
> + }
> + xsdirx_streamflow_control(xsdirxss, true);
> + } else {
> + xsdirx_streamflow_control(xsdirxss, false);
This can move out of this if statement, passing enable or !!enable directly.
Up to you.
> + }
> + spin_unlock_irqrestore(&xsdirxss->slock, flags);
> + dev_dbg(dev, "Streaming %s\n", enable ? "started" : "stopped");
> + return 0;
> +}
> +
> +/**
> + * xsdirxss_g_input_status - It is used to determine if the video signal
> + * is present / locked onto or not.
> + *
> + * @sd: V4L2 Sub device
> + * @status: status of signal locked
> + *
> + * This is used to determine if the video signal is present and locked onto
> + * by the SDI Rx core or not based on vidlocked flag.
> + *
> + * Return: zero on success
> + */
> +static int xsdirxss_g_input_status(struct v4l2_subdev *sd, u32 *status)
> +{
> + struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
> + unsigned long flags;
> +
> + spin_lock_irqsave(&xsdirxss->slock, flags);
> + if (!xsdirxss->vidlocked)
> + *status = V4L2_IN_ST_NO_SYNC | V4L2_IN_ST_NO_SIGNAL;
> + else
> + *status = 0;
> +
> + spin_unlock_irqrestore(&xsdirxss->slock, flags);
> + return 0;
> +}
> +
> +static struct v4l2_mbus_framefmt *
> +__xsdirxss_get_pad_format(struct xsdirxss_state *xsdirxss,
> + struct v4l2_subdev_pad_config *cfg,
> + unsigned int pad, u32 which)
> +{
> + switch (which) {
> + case V4L2_SUBDEV_FORMAT_TRY:
> + return v4l2_subdev_get_try_format(&xsdirxss->subdev, cfg, pad);
> + case V4L2_SUBDEV_FORMAT_ACTIVE:
> + return &xsdirxss->src_format;
> + default:
> + return NULL;
> + }
> +}
> +
> +/**
> + * xsdirxss_init_cfg - Initialise the pad format config to default
> + * @sd: Pointer to V4L2 Sub device structure
> + * @cfg: Pointer to sub device pad information structure
> + *
> + * This function is used to initialize the pad format with the default
> + * values.
> + *
> + * Return: 0 on success
> + */
> +static int xsdirxss_init_cfg(struct v4l2_subdev *sd,
> + struct v4l2_subdev_pad_config *cfg)
> +{
> + struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
> + struct v4l2_mbus_framefmt *format;
> +
> + format = v4l2_subdev_get_try_format(sd, cfg, 0);
> + *format = xsdirxss->default_format;
> +
> + return 0;
> +}
> +
> +/**
> + * xsdirxss_get_set_format - This is used to get/set the pad format
> + * @sd: Pointer to V4L2 Sub device structure
> + * @cfg: Pointer to sub device pad information structure
> + * @fmt: Pointer to pad level media bus format
> + *
> + * This function is used to get and set the pad format.
> + * Since the pad format is fixed in hardware, it can't be
> + * modified on run time. So set and get are same.
> + *
> + * Return: 0 on success
> + */
> +static int xsdirxss_get_set_format(struct v4l2_subdev *sd,
> + struct v4l2_subdev_pad_config *cfg,
> + struct v4l2_subdev_format *fmt)
> +{
> + struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
> + unsigned long flags;
> +
> + spin_lock_irqsave(&xsdirxss->slock, flags);
> + if (!xsdirxss->vidlocked) {
> + spin_unlock_irqrestore(&xsdirxss->slock, flags);
> + dev_err(xsdirxss->dev, "Video not locked!\n");
> + return -EINVAL;
> + }
> +
> + fmt->format = *__xsdirxss_get_pad_format(xsdirxss, cfg,
> + fmt->pad, fmt->which);
> +
> + spin_unlock_irqrestore(&xsdirxss->slock, flags);
> + dev_dbg(xsdirxss->dev,
> + "stream width %d height %d code %d field %d colorspace %d xfer_func %d quantization %d\n",
> + fmt->format.width, fmt->format.height,
> + fmt->format.code, fmt->format.field,
> + fmt->format.colorspace, fmt->format.xfer_func,
> + fmt->format.quantization);
> + return 0;
> +}
> +
> +/**
> + * xsdirxss_enum_mbus_code - Handle pixel format enumeration
> + * @sd: pointer to v4l2 subdev structure
> + * @cfg: V4L2 subdev pad configuration
> + * @code: pointer to v4l2_subdev_mbus_code_enum structure
> + *
> + * Return: -EINVAL or zero on success
> + */
> +static int xsdirxss_enum_mbus_code(struct v4l2_subdev *sd,
> + struct v4l2_subdev_pad_config *cfg,
> + struct v4l2_subdev_mbus_code_enum *code)
> +{
> + struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
> + u32 index = code->index;
> + u32 maxindex;
> +
> + if (xsdirxss->bpc == 10)
> + maxindex = ARRAY_SIZE(xsdirxss_10bpc_mbus_fmts);
> + else
> + maxindex = ARRAY_SIZE(xsdirxss_12bpc_mbus_fmts);
> +
> + if (code->pad || index >= maxindex)
> + return -EINVAL;
> +
> + if (xsdirxss->bpc == 10)
> + code->code = xsdirxss_10bpc_mbus_fmts[index];
> + else
> + code->code = xsdirxss_12bpc_mbus_fmts[index];
> +
> + return 0;
> +}
> +
> +/**
> + * xsdirxss_enum_dv_timings - Enumerate all the supported DV timings
> + * @sd: pointer to v4l2 subdev structure
> + * @timings: DV timings structure to be returned.
> + *
> + * Return: -EINVAL incase of invalid index and pad or zero on success
> + */
> +static int xsdirxss_enum_dv_timings(struct v4l2_subdev *sd,
> + struct v4l2_enum_dv_timings *timings)
> +{
> + if (timings->index >= ARRAY_SIZE(fmt_cap))
> + return -EINVAL;
> +
> + if (timings->pad != 0)
> + return -EINVAL;
> +
> + timings->timings = fmt_cap[timings->index];
> + return 0;
> +}
> +
> +/**
> + * xsdirxss_query_dv_timings - Query for the current DV timings
> + * @sd: pointer to v4l2 subdev structure
> + * @timings: DV timings structure to be returned.
> + *
> + * Return: -ENOLCK when video is not locked, -ERANGE when corresponding timing
> + * entry is not found or zero on success.
> + */
> +static int xsdirxss_query_dv_timings(struct v4l2_subdev *sd,
> + struct v4l2_dv_timings *timings)
> +{
> + struct xsdirxss_state *state = to_xsdirxssstate(sd);
> + unsigned int i;
> + unsigned long flags;
> +
> + spin_lock_irqsave(&state->slock, flags);
> + if (!state->vidlocked) {
> + spin_unlock_irqrestore(&state->slock, flags);
> + return -ENOLCK;
> + }
> +
> + for (i = 0; i < ARRAY_SIZE(xsdirxss_dv_timings); i++) {
> + if (state->format.width == xsdirxss_dv_timings[i].width &&
> + state->format.height == xsdirxss_dv_timings[i].height &&
> + state->frame_interval.denominator ==
> + (xsdirxss_dv_timings[i].fps * 1000)) {
> + *timings = xsdirxss_dv_timings[i].timing;
> + state->detected_timings_index = i;
> + spin_unlock_irqrestore(&state->slock, flags);
> + return 0;
> + }
> + }
> + spin_unlock_irqrestore(&state->slock, flags);
> +
> + return -ERANGE;
> +}
> +
> +static int xsdirxss_s_dv_timings(struct v4l2_subdev *sd,
> + struct v4l2_dv_timings *timings)
> +{
> + struct xsdirxss_state *state = to_xsdirxssstate(sd);
> + u32 i = state->detected_timings_index;
> + unsigned long flags;
> +
> + spin_lock_irqsave(&state->slock, flags);
> + if (!state->vidlocked) {
> + spin_unlock_irqrestore(&state->slock, flags);
> + return -EINVAL;
> + }
> +
Is the spinlock needed to be held for below?
> + /* input timing should match query dv_timing */
> + if (!v4l2_match_dv_timings(timings,
> + &xsdirxss_dv_timings[i].timing,
> + 0, false)) {
> + spin_unlock_irqrestore(&state->slock, flags);
> + return -EINVAL;
> + }
> +
> + state->current_timings = *timings;
> +
> + /* Update the media bus format */
> + state->src_format = state->format;
> + spin_unlock_irqrestore(&state->slock, flags);
> +
> + return 0;
> +}
> +
> +static int xsdirxss_g_dv_timings(struct v4l2_subdev *sd,
> + struct v4l2_dv_timings *timings)
> +{
> + struct xsdirxss_state *state = to_xsdirxssstate(sd);
> +
> + *timings = state->current_timings;
This needs the lock if above doesn't change, at least per lock description.
> + return 0;
> +}
> +
> +static int xsdirxss_dv_timings_cap(struct v4l2_subdev *sd,
> + struct v4l2_dv_timings_cap *cap)
> +{
> + if (cap->pad != 0)
> + return -EINVAL;
> +
> + *cap = xsdirxss_timings_cap;
> + return 0;
> +}
> +
> +/* -----------------------------------------------------------------------------
> + * Media Operations
> + */
> +
> +static const struct media_entity_operations xsdirxss_media_ops = {
> + .link_validate = v4l2_subdev_link_validate
> +};
> +
> +static const struct v4l2_ctrl_ops xsdirxss_ctrl_ops = {
> + .g_volatile_ctrl = xsdirxss_g_volatile_ctrl,
> + .s_ctrl = xsdirxss_s_ctrl
> +};
> +
> +static const struct v4l2_ctrl_config xsdirxss_edh_ctrls[] = {
> + {
> + .ops = &xsdirxss_ctrl_ops,
> + .id = V4L2_CID_XILINX_SDIRX_EDH_ERROR_SOURCES,
> + .name = "SDI Rx : EDH Error Count Enable",
> + .type = V4L2_CTRL_TYPE_BITMASK,
> + .min = 0,
> + .max = XSDIRX_EDH_ALLERR_MASK,
> + .def = 0,
> + }, {
> + .ops = &xsdirxss_ctrl_ops,
> + .id = V4L2_CID_XILINX_SDIRX_EDH_ERRCNT,
> + .name = "SDI Rx : EDH Error Count",
> + .type = V4L2_CTRL_TYPE_INTEGER,
> + .min = 0,
> + .max = 0xffff,
> + .step = 1,
> + .def = 0,
> + .flags = V4L2_CTRL_FLAG_VOLATILE | V4L2_CTRL_FLAG_READ_ONLY,
> + }, {
> + .ops = &xsdirxss_ctrl_ops,
> + .id = V4L2_CID_XILINX_SDIRX_EDH_STATUS,
> + .name = "SDI Rx : EDH Status",
> + .type = V4L2_CTRL_TYPE_INTEGER,
> + .min = 0,
> + .max = 0xffffffff,
> + .step = 1,
> + .def = 0,
> + .flags = V4L2_CTRL_FLAG_VOLATILE | V4L2_CTRL_FLAG_READ_ONLY,
> + }
> +};
> +
> +static const struct v4l2_ctrl_config xsdirxss_ctrls[] = {
> + {
> + .ops = &xsdirxss_ctrl_ops,
> + .id = V4L2_CID_XILINX_SDIRX_FRAMER,
> + .name = "SDI Rx : Enable Framer",
> + .type = V4L2_CTRL_TYPE_BOOLEAN,
> + .min = false,
> + .max = true,
> + .step = 1,
> + .def = true,
> + }, {
> + .ops = &xsdirxss_ctrl_ops,
> + .id = V4L2_CID_XILINX_SDIRX_VIDLOCK_WINDOW,
> + .name = "SDI Rx : Video Lock Window",
> + .type = V4L2_CTRL_TYPE_INTEGER,
> + .min = 0,
> + .max = 0xffffffff,
> + .step = 1,
> + .def = XSDIRX_DEFAULT_VIDEO_LOCK_WINDOW,
> + }, {
> + .ops = &xsdirxss_ctrl_ops,
> + .id = V4L2_CID_XILINX_SDIRX_SEARCH_MODES,
> + .name = "SDI Rx : Modes search Mask",
> + .type = V4L2_CTRL_TYPE_BITMASK,
> + .min = 0,
> + .max = XSDIRX_DETECT_ALL_MODES,
> + .def = XSDIRX_DETECT_ALL_MODES,
> + }, {
> + .ops = &xsdirxss_ctrl_ops,
> + .id = V4L2_CID_XILINX_SDIRX_MODE_DETECT,
> + .name = "SDI Rx : Mode Detect Status",
> + .type = V4L2_CTRL_TYPE_INTEGER,
> + .min = XSDIRX_MODE_SD_OFFSET,
> + .max = XSDIRX_MODE_12GF_OFFSET,
> + .step = 1,
> + .flags = V4L2_CTRL_FLAG_VOLATILE | V4L2_CTRL_FLAG_READ_ONLY,
> + }, {
> + .ops = &xsdirxss_ctrl_ops,
> + .id = V4L2_CID_XILINX_SDIRX_CRC,
> + .name = "SDI Rx : CRC Error status",
> + .type = V4L2_CTRL_TYPE_INTEGER,
> + .min = 0,
> + .max = 0xffffffff,
> + .step = 1,
> + .def = 0,
> + .flags = V4L2_CTRL_FLAG_VOLATILE | V4L2_CTRL_FLAG_READ_ONLY,
> + }, {
> + .ops = &xsdirxss_ctrl_ops,
> + .id = V4L2_CID_XILINX_SDIRX_TS_IS_INTERLACED,
> + .name = "SDI Rx : TS is Interlaced",
> + .type = V4L2_CTRL_TYPE_BOOLEAN,
> + .min = false,
> + .max = true,
> + .def = false,
> + .step = 1,
> + .flags = V4L2_CTRL_FLAG_VOLATILE | V4L2_CTRL_FLAG_READ_ONLY,
> + },
> +};
> +
> +static const struct v4l2_subdev_core_ops xsdirxss_core_ops = {
> + .log_status = xsdirxss_log_status,
> + .subscribe_event = xsdirxss_subscribe_event,
> + .unsubscribe_event = v4l2_event_subdev_unsubscribe,
> +};
> +
> +static const struct v4l2_subdev_video_ops xsdirxss_video_ops = {
> + .g_frame_interval = xsdirxss_g_frame_interval,
> + .s_stream = xsdirxss_s_stream,
> + .g_input_status = xsdirxss_g_input_status,
> + .query_dv_timings = xsdirxss_query_dv_timings,
> + .g_dv_timings = xsdirxss_g_dv_timings,
> + .s_dv_timings = xsdirxss_s_dv_timings,
> +};
> +
> +static const struct v4l2_subdev_pad_ops xsdirxss_pad_ops = {
> + .init_cfg = xsdirxss_init_cfg,
> + .get_fmt = xsdirxss_get_set_format,
> + .set_fmt = xsdirxss_get_set_format,
> + .enum_mbus_code = xsdirxss_enum_mbus_code,
> + .enum_dv_timings = xsdirxss_enum_dv_timings,
> + .dv_timings_cap = xsdirxss_dv_timings_cap,
> +};
> +
> +static const struct v4l2_subdev_ops xsdirxss_ops = {
> + .core = &xsdirxss_core_ops,
> + .video = &xsdirxss_video_ops,
> + .pad = &xsdirxss_pad_ops
> +};
> +
> +/* -----------------------------------------------------------------------------
> + * Platform Device Driver
> + */
> +
> +static int xsdirxss_parse_of(struct xsdirxss_state *xsdirxss)
> +{
> + struct device_node *node = xsdirxss->dev->of_node;
> + struct device *dev = xsdirxss->dev;
> + int ret;
> +
> + xsdirxss->include_edh = of_property_read_bool(node, "xlnx,include-edh");
> + dev_dbg(dev, "EDH property = %s\n",
> + xsdirxss->include_edh ? "Present" : "Absent");
> +
> + ret = of_property_read_u32(node, "xlnx,line-rate", &xsdirxss->mode);
> + if (ret < 0) {
> + dev_err(dev, "xlnx,line-rate property not found\n");
> + return ret;
> + }
> +
> + if (xsdirxss->mode != XSDI_STD_3G && xsdirxss->mode != XSDI_STD_6G &&
> + xsdirxss->mode != XSDI_STD_12G_8DS) {
> + dev_err(dev, "Invalid Line Rate\n");
> + return -EINVAL;
> + }
> +
> + dev_dbg(dev, "SDI Rx Line Rate / mode = %d\n", xsdirxss->mode);
> +
> + ret = of_property_read_u32(node, "xlnx,bpc", &xsdirxss->bpc);
> + if (ret == -EINVAL) {
> + xsdirxss->bpc = 10;
> + dev_dbg(dev, "set default bpc as 10\n");
> + } else if (ret < 0) {
> + dev_err(dev, "failed to get xlnx,bpc\n");
> + return ret;
> + }
> +
> + if (xsdirxss->bpc != 10 && xsdirxss->bpc != 12) {
> + dev_err(dev, "bits per component=%u. Can be 10 or 12 only\n",
> + xsdirxss->bpc);
> + return -EINVAL;
> + }
> +
> + return ret;
> +}
> +
> +static int xsdirxss_probe(struct platform_device *pdev)
> +{
> + struct v4l2_subdev *subdev;
> + struct xsdirxss_state *xsdirxss;
> + struct device *dev;
> + int ret, irq;
> + unsigned int num_ctrls, i;
> +
> + xsdirxss = devm_kzalloc(&pdev->dev, sizeof(*xsdirxss), GFP_KERNEL);
> + if (!xsdirxss)
> + return -ENOMEM;
> +
> + xsdirxss->dev = &pdev->dev;
> + dev = xsdirxss->dev;
> +
> + spin_lock_init(&xsdirxss->slock);
> + ret = xsdirxss_parse_of(xsdirxss);
> + if (ret < 0)
> + return ret;
> +
> + xsdirxss->iomem = devm_platform_ioremap_resource(pdev, 0);
> + if (IS_ERR(xsdirxss->iomem))
> + return PTR_ERR(xsdirxss->iomem);
> +
> + xsdirxss->num_clks = ARRAY_SIZE(xsdirxss_clks);
> + xsdirxss->clks = devm_kcalloc(dev, xsdirxss->num_clks,
> + sizeof(*xsdirxss->clks), GFP_KERNEL);
> + if (!xsdirxss->clks)
> + return -ENOMEM;
> +
> + for (i = 0; i < xsdirxss->num_clks; i++)
> + xsdirxss->clks[i].id = xsdirxss_clks[i];
> +
> + ret = devm_clk_bulk_get(dev, xsdirxss->num_clks, xsdirxss->clks);
> + if (ret)
> + return ret;
> +
> + ret = clk_bulk_prepare_enable(xsdirxss->num_clks, xsdirxss->clks);
> + if (ret)
> + return ret;
> +
> + /* Reset the core */
> + xsdirx_streamflow_control(xsdirxss, false);
> + XSDIRX_CORE_DISABLE(xsdirxss);
> + /* Clear all interrupts */
> + xsdirxss_set(xsdirxss, XSDIRX_ISR_REG, XSDIRX_INTR_ALL_MASK);
> + xsdirxss_clr(xsdirxss, XSDIRX_IER_REG, XSDIRX_INTR_ALL_MASK);
> + xsdirxss_set(xsdirxss, XSDIRX_IER_REG, XSDIRX_INTR_ALL_MASK);
> + XSDIRX_GLOBAL_INTR_ENABLE(xsdirxss);
Looking here, inlining the macro will be better.
xsdirxss_set(xsdirxss, XSDIRX_GLBL_IER_REG, XSDIRX_GLBL_INTR_EN_MASK)
> + xsdirxss_write(xsdirxss, XSDIRX_CRC_ERRCNT_REG, 0xffff);
> +
> + /* Register interrupt handler */
> + irq = platform_get_irq(pdev, 0);
> + ret = devm_request_threaded_irq(dev, irq, NULL, xsdirxss_irq_handler,
> + IRQF_ONESHOT, dev_name(dev), xsdirxss);
> + if (ret) {
> + dev_err(dev, "Err = %d Interrupt handler reg failed!\n",
> + ret);
> + goto clk_err;
> + }
> +
> + /* Initialize V4L2 subdevice and media entity */
> + xsdirxss->pad.flags = MEDIA_PAD_FL_SOURCE;
> +
> + /* Initialize the default format */
> + if (xsdirxss->bpc == 10)
> + xsdirxss->default_format.code = MEDIA_BUS_FMT_UYVY10_1X20;
> + else
> + xsdirxss->default_format.code = MEDIA_BUS_FMT_UYVY12_1X24;
> + xsdirxss->default_format.field = V4L2_FIELD_NONE;
> + xsdirxss->default_format.colorspace = V4L2_COLORSPACE_REC709;
> + xsdirxss->default_format.width = XSDIRX_DEFAULT_WIDTH;
> + xsdirxss->default_format.height = XSDIRX_DEFAULT_HEIGHT;
> + xsdirxss->default_format.xfer_func = V4L2_XFER_FUNC_709;
> + xsdirxss->default_format.quantization = V4L2_QUANTIZATION_LIM_RANGE;
> +
> + xsdirxss->format = xsdirxss->default_format;
> +
> + /* Initialize V4L2 subdevice and media entity */
> + subdev = &xsdirxss->subdev;
> + v4l2_subdev_init(subdev, &xsdirxss_ops);
> +
> + subdev->dev = &pdev->dev;
> + strscpy(subdev->name, dev_name(dev), sizeof(subdev->name));
> +
> + subdev->flags = V4L2_SUBDEV_FL_HAS_EVENTS | V4L2_SUBDEV_FL_HAS_DEVNODE;
> +
> + subdev->entity.ops = &xsdirxss_media_ops;
> +
> + v4l2_set_subdevdata(subdev, xsdirxss);
> +
> + ret = media_entity_pads_init(&subdev->entity, 1, &xsdirxss->pad);
> + if (ret < 0)
> + goto error;
> +
> + /* Initialise and register the controls */
> + num_ctrls = ARRAY_SIZE(xsdirxss_ctrls);
> +
> + if (xsdirxss->include_edh)
> + num_ctrls += ARRAY_SIZE(xsdirxss_edh_ctrls);
> +
> + v4l2_ctrl_handler_init(&xsdirxss->ctrl_handler, num_ctrls);
> +
> + for (i = 0; i < ARRAY_SIZE(xsdirxss_ctrls); i++) {
> + struct v4l2_ctrl *ctrl;
> +
> + dev_dbg(dev, "%d %s ctrl = 0x%x\n", i, xsdirxss_ctrls[i].name,
> + xsdirxss_ctrls[i].id);
> +
> + ctrl = v4l2_ctrl_new_custom(&xsdirxss->ctrl_handler,
> + &xsdirxss_ctrls[i], NULL);
> + }
> +
> + if (xsdirxss->include_edh) {
> + for (i = 0; i < ARRAY_SIZE(xsdirxss_edh_ctrls); i++) {
> + struct v4l2_ctrl *ctrl;
> +
> + dev_dbg(dev, "%d %s ctrl = 0x%x\n", i,
> + xsdirxss_edh_ctrls[i].name,
> + xsdirxss_edh_ctrls[i].id);
> +
> + ctrl = v4l2_ctrl_new_custom(&xsdirxss->ctrl_handler,
> + &xsdirxss_edh_ctrls[i],
> + NULL);
> + }
> + }
> +
> + if (xsdirxss->ctrl_handler.error) {
> + dev_err(dev, "failed to add controls\n");
> + ret = xsdirxss->ctrl_handler.error;
> + goto error;
> + }
> +
> + subdev->ctrl_handler = &xsdirxss->ctrl_handler;
> +
> + ret = v4l2_ctrl_handler_setup(&xsdirxss->ctrl_handler);
> + if (ret < 0) {
> + dev_err(dev, "failed to set controls\n");
> + goto error;
> + }
> +
> + platform_set_drvdata(pdev, xsdirxss);
> +
> + ret = v4l2_async_register_subdev(subdev);
> + if (ret < 0) {
> + dev_err(dev, "failed to register subdev\n");
> + goto error;
> + }
> +
> + xsdirxss->prev_is_frac = -1;
> +
> + XSDIRX_CORE_ENABLE(xsdirxss);
> +
> + return 0;
Nit. Ane empty line.
> +error:
> + v4l2_ctrl_handler_free(&xsdirxss->ctrl_handler);
> + media_entity_cleanup(&subdev->entity);
> + XSDIRX_GLOBAL_INTR_DISABLE(xsdirxss);
> + xsdirxss_clr(xsdirxss, XSDIRX_IER_REG, XSDIRX_INTR_ALL_MASK);
> +clk_err:
> + clk_bulk_disable_unprepare(xsdirxss->num_clks, xsdirxss->clks);
> + return ret;
> +}
> +
> +static int xsdirxss_remove(struct platform_device *pdev)
> +{
> + struct xsdirxss_state *xsdirxss = platform_get_drvdata(pdev);
> + struct v4l2_subdev *subdev = &xsdirxss->subdev;
> +
> + XSDIRX_CORE_DISABLE(xsdirxss);
> + XSDIRX_GLOBAL_INTR_DISABLE(xsdirxss);
> + xsdirxss_clr(xsdirxss, XSDIRX_IER_REG, XSDIRX_INTR_ALL_MASK);
> + xsdirx_streamflow_control(xsdirxss, false);
> +
> + v4l2_async_unregister_subdev(subdev);
> + v4l2_ctrl_handler_free(&xsdirxss->ctrl_handler);
> + media_entity_cleanup(&subdev->entity);
> +
> + clk_bulk_disable_unprepare(xsdirxss->num_clks, xsdirxss->clks);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id xsdirxss_of_id_table[] = {
> + { .compatible = "xlnx,v-smpte-uhdsdi-rx-ss-2.0" },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, xsdirxss_of_id_table);
> +
> +static struct platform_driver xsdirxss_driver = {
> + .driver = {
> + .name = "xilinx-sdirxss",
> + .of_match_table = xsdirxss_of_id_table,
> + },
> + .probe = xsdirxss_probe,
> + .remove = xsdirxss_remove,
> +};
> +
> +module_platform_driver(xsdirxss_driver);
> +
> +MODULE_AUTHOR("Vishal Sagar <vsagar@...inx.com>");
> +MODULE_DESCRIPTION("Xilinx SDI Rx Subsystem Driver");
> +MODULE_LICENSE("GPL v2");
> diff --git a/include/uapi/linux/v4l2-controls.h b/include/uapi/linux/v4l2-controls.h
> index 62271418c1be..9526a6acc6f4 100644
> --- a/include/uapi/linux/v4l2-controls.h
> +++ b/include/uapi/linux/v4l2-controls.h
> @@ -198,6 +198,12 @@ enum v4l2_colorfx {
> */
> #define V4L2_CID_USER_ATMEL_ISC_BASE (V4L2_CID_USER_BASE + 0x10c0)
>
> +/*
> + * The base for the Xilinx SDI Rx driver controls.
> + * We reserve 16 controls for this driver.
> + */
> +#define V4L2_CID_USER_XILINX_SDIRX_BASE (V4L2_CID_USER_BASE + 0x10e0)
> +
> /* MPEG-class control IDs */
> /* The MPEG controls are applicable to all codec controls
> * and the 'MPEG' part of the define is historical */
> diff --git a/include/uapi/linux/xilinx-sdirxss.h b/include/uapi/linux/xilinx-sdirxss.h
> new file mode 100644
> index 000000000000..1bcbf5852b22
> --- /dev/null
> +++ b/include/uapi/linux/xilinx-sdirxss.h
> @@ -0,0 +1,283 @@
> +/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
> +/*
> + * Xilinx SDI Rx Subsystem mode, event, custom timings and
> + * flag definitions.
> + *
> + * Copyright (C) 2019 - 2020 Xilinx, Inc.
> + *
> + * Contacts: Vishal Sagar <vishal.sagar@...inx.com>
> + */
> +
> +#ifndef __UAPI_XILINX_SDIRXSS_H__
> +#define __UAPI_XILINX_SDIRXSS_H__
> +
> +#include <linux/types.h>
> +#include <linux/v4l2-controls.h>
> +#include <linux/v4l2-dv-timings.h>
> +#include <linux/videodev2.h>
> +
> +/*
> + * Events
> + *
> + * V4L2_EVENT_XILINX_SDIRX_UND_OVR_FLOW: Video in to AXI4 Stream core
> + * under/overflowed during a resolution or frame rate change.
> + */
> +#define V4L2_EVENT_XILINX_SDIRX_CLASS (V4L2_EVENT_PRIVATE_START | 0x200)
> +#define V4L2_EVENT_XILINX_SDIRX_UND_OVR_FLOW \
> + (V4L2_EVENT_XILINX_SDIRX_CLASS | 0x1)
> +
> +#define XILINX_SDIRX_UNDERFLOW_EVENT BIT(1)
> +#define XILINX_SDIRX_OVERFLOW_EVENT BIT(2)
> +/*
> + * This enum is used to prepare the bitmask of modes to be detected
> + */
> +enum {
> + XSDIRX_MODE_SD_OFFSET = 0,
> + XSDIRX_MODE_HD_OFFSET,
> + XSDIRX_MODE_3GA_OFFSET,
> + XSDIRX_MODE_3GB_OFFSET,
> + XSDIRX_MODE_6G_OFFSET,
> + XSDIRX_MODE_12GI_OFFSET,
> + XSDIRX_MODE_12GF_OFFSET,
> + XSDIRX_MODE_NUM_SUPPORTED,
> +};
> +
> +#define XSDIRX_DETECT_ALL_MODES (BIT(XSDIRX_MODE_SD_OFFSET) | \
> + BIT(XSDIRX_MODE_HD_OFFSET) | \
> + BIT(XSDIRX_MODE_3GA_OFFSET) | \
> + BIT(XSDIRX_MODE_3GB_OFFSET) | \
> + BIT(XSDIRX_MODE_6G_OFFSET) | \
> + BIT(XSDIRX_MODE_12GI_OFFSET) | \
> + BIT(XSDIRX_MODE_12GF_OFFSET))
> +
> +/*
> + * EDH - Error Detection and Handling.
> + * In the SD-SDI mode, the UHD-SDI core fully supports RP 165.
> + * The bitmask is named as XSDIRX_EDH_ERRCNT_XX_YY_ERR except
> + * for packet checksum error.
> + *
> + * XX - EDH Error Types
> + * ANC - Ancillary Data Packet Errors
> + * FF - Full Field Errors
> + * AP - Active Portion Errors
> + *
> + * YY - Error Flags
> + * EDH - error detected here
> + * EDA - error Detected already
> + * IDH - internal error detected here
> + * IDA - internal error detected already
> + * UES - unknown error status
> + *
> + * Refer to Sec 4.3 Error Flags in RP 165-1994 for details
> + */
> +
> +#define XSDIRX_EDH_ERRCNT_ANC_EDH_ERR BIT(0)
> +#define XSDIRX_EDH_ERRCNT_ANC_EDA_ERR BIT(1)
> +#define XSDIRX_EDH_ERRCNT_ANC_IDH_ERR BIT(2)
> +#define XSDIRX_EDH_ERRCNT_ANC_IDA_ERR BIT(3)
> +#define XSDIRX_EDH_ERRCNT_ANC_UES_ERR BIT(4)
> +#define XSDIRX_EDH_ERRCNT_FF_EDH_ERR BIT(5)
> +#define XSDIRX_EDH_ERRCNT_FF_EDA_ERR BIT(6)
> +#define XSDIRX_EDH_ERRCNT_FF_IDH_ERR BIT(7)
> +#define XSDIRX_EDH_ERRCNT_FF_IDA_ERR BIT(8)
> +#define XSDIRX_EDH_ERRCNT_FF_UES_ERR BIT(9)
> +#define XSDIRX_EDH_ERRCNT_AP_EDH_ERR BIT(10)
> +#define XSDIRX_EDH_ERRCNT_AP_EDA_ERR BIT(11)
> +#define XSDIRX_EDH_ERRCNT_AP_IDH_ERR BIT(12)
> +#define XSDIRX_EDH_ERRCNT_AP_IDA_ERR BIT(13)
> +#define XSDIRX_EDH_ERRCNT_AP_UES_ERR BIT(14)
> +#define XSDIRX_EDH_ERRCNT_PKT_CHKSUM_ERR BIT(15)
> +
> +#define XSDIRX_EDH_ALLERR_MASK 0xFFFF
Nit, lowercase for hex values.
Thanks!
-hyun
> +
> +/*
> + * V4L2 Controls - We reserved 16 controls for this driver.
> + *
> + * The V4L2_CID_XILINX_SDIRX_EDH_* controls are present only if
> + * EDH is enabled.
> + * The controls which can be set should only be set before enabling
> + * streaming. The controls which can be got should be called while
> + * streaming to get correct values.
> + * The V4L2_CID_XILINX_SDIRX_MODE_DETECT can be called when query dv timing
> + * returns a valid timing.
> + */
> +
> +/*
> + * Framer Control to enable or disable the framer. When this is set, the framer
> + * automatically readjusts the output word alignment to match the alignment of
> + * each timing reference signal(TRS). Normally this should be set. But user may
> + * control this input to implement TRS filtering to prevent a signal misaligned
> + * TRS from causing erroneous alignment changes.
> + * Refer to PG205 rx_frame_en for more details.
> + */
> +#define V4L2_CID_XILINX_SDIRX_FRAMER (V4L2_CID_USER_XILINX_SDIRX_BASE + 1)
> +
> +/*
> + * Video Lock Window Control to set the video lock window value
> + * This is the amount of time the mode and transport stream need
> + * to be locked before a video lock interrupt occurs.
> + */
> +#define V4L2_CID_XILINX_SDIRX_VIDLOCK_WINDOW (V4L2_CID_USER_XILINX_SDIRX_BASE + 2)
> +
> +/*
> + * EDH Error Mask Control to enable EDH error count
> + * This control takes in the bitmask of XSDIRX_EDH_ERRCNT_*_ERR to enable counting
> + * such errors.
> + */
> +#define V4L2_CID_XILINX_SDIRX_EDH_ERROR_SOURCES (V4L2_CID_USER_XILINX_SDIRX_BASE + 3)
> +
> +/*
> + * Mode search Control to pass the bit mask of modes to detect.
> + * If only 1 bit is set, the driver programs IP to be in fixed mode else
> + * in multi detection mode.
> + *
> + * Set this when not streaming.
> + *
> + * bit 0 set to detect SD mode,
> + * bit 1 set to detect HD mode,
> + * bit 2 set to detect 3GA mode,
> + * bit 3 set to detect 3GB mode,
> + * bit 4 set to detect 6G mode,
> + * bit 5 set to detect 12G integer frame rate mode,
> + * bit 6 set to detect 12G fractional frame rate mode,
> + */
> +#define V4L2_CID_XILINX_SDIRX_SEARCH_MODES (V4L2_CID_USER_XILINX_SDIRX_BASE + 4)
> +
> +/*
> + * Get Detected SDI Mode control (read only)
> + *
> + * Control Value - Mode detected
> + * 0 - SD
> + * 1 - HD
> + * 2 - 3GA
> + * 3 - 3GB
> + * 4 - 6G
> + * 5 - 12G integer frame rate
> + * 6 - 12G fractional frame rate
> + */
> +#define V4L2_CID_XILINX_SDIRX_MODE_DETECT (V4L2_CID_USER_XILINX_SDIRX_BASE + 5)
> +
> +/* Get number of CRC errors status control
> + *
> + * When a CRC is detected on a line, the CRC error signal of that data stream
> + * becomes asserted starting a few clock cycles after the last CRC word is
> + * output on the data stream ports following the EAV that ends the line
> + * containing the error. The CRC signal remains asserted for one line time.
> + *
> + * The LSB 16 bits of value returned by thsi control represent the error
> + * signal on each of 16 data streams. The MSB 16 bits contains the accumulated
> + * error count.
> + *
> + * Refer to PG205 rx_crc_err_dsX (X = 1 to 16) description for details.
> + */
> +#define V4L2_CID_XILINX_SDIRX_CRC (V4L2_CID_USER_XILINX_SDIRX_BASE + 6)
> +
> +/*
> + * Get EDH error count control
> + *
> + * Reading this control will give the number of EDH errors occurred based
> + * on the bitmask passed in V4L2_CID_XILINX_SDIRX_EDH_ERROR_SOURCES.
> + *
> + * It increments once per field when any of the error conditions enabled by
> + * the RX_EDH_ERRCNT_EN register bit(s) occur during that field.
> + *
> + * Refer to PG205 rx_edh_errcnt
> + */
> +#define V4L2_CID_XILINX_SDIRX_EDH_ERRCNT (V4L2_CID_USER_XILINX_SDIRX_BASE + 7)
> +
> +/*
> + * Get EDH status control
> + *
> + * This control returns the RX_EDH_STS register contents.
> + * Refer to PG290 register space section for more details.
> + */
> +#define V4L2_CID_XILINX_SDIRX_EDH_STATUS (V4L2_CID_USER_XILINX_SDIRX_BASE + 8)
> +
> +/* Get Transport Interlaced status whether it is interlaced or not */
> +#define V4L2_CID_XILINX_SDIRX_TS_IS_INTERLACED (V4L2_CID_USER_XILINX_SDIRX_BASE + 9)
> +
> +/*
> + * Xilinx DV timings
> + * TODO - Remove these once they are in v4l2-dv-timings.h
> + */
> +#define XLNX_V4L2_DV_BT_2048X1080P24 { \
> + .type = V4L2_DV_BT_656_1120, \
> + V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
> + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> + 74250000, 510, 44, 148, 4, 5, 36, 0, 0, 0, \
> + V4L2_DV_BT_STD_SDI) \
> +}
> +
> +#define XLNX_V4L2_DV_BT_2048X1080P25 { \
> + .type = V4L2_DV_BT_656_1120, \
> + V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
> + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> + 74250000, 400, 44, 148, 4, 5, 36, 0, 0, 0, \
> + V4L2_DV_BT_STD_SDI) \
> +}
> +
> +#define XLNX_V4L2_DV_BT_2048X1080P30 { \
> + .type = V4L2_DV_BT_656_1120, \
> + V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
> + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> + 74250000, 66, 20, 66, 4, 5, 36, 0, 0, 0, \
> + V4L2_DV_BT_STD_SDI) \
> +}
> +
> +#define XLNX_V4L2_DV_BT_2048X1080I48 { \
> + .type = V4L2_DV_BT_656_1120, \
> + V4L2_INIT_BT_TIMINGS(2048, 1080, 1, \
> + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> + 74250000, 329, 44, 329, 2, 5, 15, 3, 5, 15, \
> + V4L2_DV_BT_STD_SDI) \
> +}
> +
> +#define XLNX_V4L2_DV_BT_2048X1080I50 { \
> + .type = V4L2_DV_BT_656_1120, \
> + V4L2_INIT_BT_TIMINGS(2048, 1080, 1, \
> + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> + 74250000, 274, 44, 274, 2, 5, 15, 3, 5, 15, \
> + V4L2_DV_BT_STD_SDI) \
> +}
> +
> +#define XLNX_V4L2_DV_BT_2048X1080I60 { \
> + .type = V4L2_DV_BT_656_1120, \
> + V4L2_INIT_BT_TIMINGS(2048, 1080, 1, \
> + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> + 74250000, 66, 20, 66, 2, 5, 15, 3, 5, 15, \
> + V4L2_DV_BT_STD_SDI) \
> +}
> +
> +#define XLNX_V4L2_DV_BT_2048X1080P48 { \
> + .type = V4L2_DV_BT_656_1120, \
> + V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
> + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> + 148500000, 510, 44, 148, 4, 5, 36, 0, 0, 0, \
> + V4L2_DV_BT_STD_SDI) \
> +}
> +
> +#define XLNX_V4L2_DV_BT_2048X1080P50 { \
> + .type = V4L2_DV_BT_656_1120, \
> + V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
> + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> + 148500000, 400, 44, 148, 4, 5, 36, 0, 0, 0, \
> + V4L2_DV_BT_STD_SDI) \
> +}
> +
> +#define XLNX_V4L2_DV_BT_2048X1080P60 { \
> + .type = V4L2_DV_BT_656_1120, \
> + V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
> + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> + 148500000, 88, 44, 20, 4, 5, 36, 0, 0, 0, \
> + V4L2_DV_BT_STD_SDI) \
> +}
> +
> +#define XLNX_V4L2_DV_BT_1920X1080I48 { \
> + .type = V4L2_DV_BT_656_1120, \
> + V4L2_INIT_BT_TIMINGS(1920, 1080, 1, \
> + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> + 148500000, 371, 88, 371, 2, 5, 15, 3, 5, 15, \
> + V4L2_DV_BT_STD_SDI) \
> +}
> +
> +#endif /* __UAPI_XILINX_SDIRXSS_H__ */
> --
> 2.21.0
>
>
Powered by blists - more mailing lists