linux-kernel - [PATCH V2 2/3] arm64: dts: qcom: sc7180: Add sleep pin ctrl for BT uart

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <1595563082-2353-3-git-send-email-skakit@codeaurora.org>
Date:   Fri, 24 Jul 2020 09:28:01 +0530
From:   satya priya <skakit@...eaurora.org>
To:     Bjorn Andersson <bjorn.andersson@...aro.org>,
        gregkh@...uxfoundation.org
Cc:     Andy Gross <agross@...nel.org>, Rob Herring <robh+dt@...nel.org>,
        Matthias Kaehlcke <mka@...omium.org>,
        linux-arm-msm@...r.kernel.org, devicetree@...r.kernel.org,
        linux-kernel@...r.kernel.org, akashast@...eaurora.org,
        rojay@...eaurora.org, msavaliy@....qualcomm.com,
        satya priya <skakit@...eaurora.org>
Subject: [PATCH V2 2/3] arm64: dts: qcom: sc7180: Add sleep pin ctrl for BT uart

Add sleep pin ctrl for BT uart, and also change the bias
configuration to match Bluetooth module.

Signed-off-by: satya priya <skakit@...eaurora.org>
---
Changes in V2:
 - This patch adds sleep state for BT UART. Newly added in V2.

 arch/arm64/boot/dts/qcom/sc7180-idp.dts | 42 ++++++++++++++++++++++++++++-----
 1 file changed, 36 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
index 26cc491..bc919f2 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
@@ -469,20 +469,50 @@
 
 &qup_uart3_default {
 	pinconf-cts {
-		/*
-		 * Configure a pull-down on 38 (CTS) to match the pull of
-		 * the Bluetooth module.
-		 */
+		/* Configure no pull on 38 (CTS) to match Bluetooth module */
 		pins = "gpio38";
+		bias-disable;
+	};
+
+	pinconf-rts {
+		/* We'll drive 39 (RTS), so configure pull-down */
+		pins = "gpio39";
+		drive-strength = <2>;
 		bias-pull-down;
+	};
+
+	pinconf-tx {
+		/* We'll drive 40 (TX), so no pull */
+		pins = "gpio40";
+		drive-strength = <2>;
+		bias-disable;
 		output-high;
 	};
 
+	pinconf-rx {
+		/*
+		 * Configure a pull-up on 41 (RX). This is needed to avoid
+		 * garbage data when the TX pin of the Bluetooth module is
+		 * in tri-state (module powered off or not driving the
+		 * signal yet).
+		 */
+		pins = "gpio41";
+		bias-pull-up;
+	};
+};
+
+&qup_uart3_sleep {
+	pinconf-cts {
+		/* Configure no-pull on 38 (CTS) to match Bluetooth module */
+		pins = "gpio38";
+		bias-disable;
+	};
+
 	pinconf-rts {
-		/* We'll drive 39 (RTS), so no pull */
+		/* We'll drive 39 (RTS), so configure pull-down */
 		pins = "gpio39";
 		drive-strength = <2>;
-		bias-disable;
+		bias-pull-down;
 	};
 
 	pinconf-tx {
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation