| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20200821121755.24599-1-martin.kepplinger@puri.sm>
Date: Fri, 21 Aug 2020 14:17:53 +0200
From: Martin Kepplinger <martin.kepplinger@...i.sm>
To: robh@...nel.org, kernel@...i.sm, shawnguo@...nel.org,
s.hauer@...gutronix.de, kernel@...gutronix.de, festevam@...il.com,
linux-imx@....com, mchehab@...nel.org, Anson.Huang@....com,
agx@...xcpu.org, angus@...ea.ca, broonie@...nel.org
Cc: linux-kernel@...r.kernel.org, devicetree@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org,
Martin Kepplinger <martin.kepplinger@...i.sm>,
Daniel Baluta <daniel.baluta@....com>
Subject: [PATCH v6 1/3] arm64: dts: Add a device tree for the Librem 5 phone
From: "Angus Ainslie (Purism)" <angus@...ea.ca>
Add a devicetree description for the Librem 5 phone. 4 hardware revisions
have been available. Some revisions include changes that need different
software to be run. So far, r3 ("Dogwood") is one such example, see:
"Aspen" r0 not supported (very few devices exist)
"Birch" r1 supported by r2
"Chestnut" r2 added by this patch
"Dogwood" r3 added by this patch
"Evergreen" r4 tba / most likely supported by r3
See https://puri.sm/products/librem-5/ for more information.
This boots to a working console with working WWAN modem, wifi usdhc,
IMU sensor device, proximity sensor, haptic motor, gpio keys, GNSS and LEDs.
Signed-off-by: Martin Kepplinger <martin.kepplinger@...i.sm>
Signed-off-by: Angus Ainslie (Purism) <angus@...ea.ca>
Signed-off-by: Guido Günther <agx@...xcpu.org>
Reviewed-by: Daniel Baluta <daniel.baluta@....com> (for the audio part)
Reviewed-by: Fabio Estevam <festevam@...il.com>
---
revision history
----------------
v6:
thanks a lot Rob and Fabio for reviewing
* add pinctrl-names = "default" where it was missing
* removed the lm3560 flash/torch device. add it when the driver is hooked up.
* fsl-lpspi cs-gpios active low
* remove unneeded comment and one node naming improvement
* add near-level to proximity description
* add missing Acked-by: Rob Herring to dt-bindings commit message
v5:
thanks a lot Pavel for reviewing again
* remove pwmleds (no stable interface yet)
https://lore.kernel.org/linux-arm-kernel/20200731082725.21878-1-martin.kepplinger@puri.sm/T/
v4:
thanks a lot Shawn for reviewing
* rename to dtsi and split out r2 and r3 dts with revision specifics
* add the USB2642 hard-wired Hub
* fix charge controller boost-max-current
* disable pullup on CHRG_INT (not needed due to external one)
* add documentation for the boards' compatible strings
* fix led-backlight propery usage
* coding style fixes
https://lore.kernel.org/linux-devicetree/20200721153225.7593-1-martin.kepplinger@puri.sm/T/
v3:
thanks a lot Mark for reviewing! changes since v2:
* nicer audio cards names
* squash unneeded audio_pwr regulator
* remove the susphy_quirk from dwc3_1 after more testing
* add usdhc2 card detect via gpio
* add headphone detect for audio card
https://lore.kernel.org/linux-arm-kernel/20200617073821.16737-1-martin.kepplinger@puri.sm/T/
v2:
thanks a lot Marco, Daniel and Pavel for reviewing. changes since v1:
* alphabetical sortings / more consistent node names
* remove unused regulator and pinctrl descriptions
* generic labels for leds, backlight, flash and torch
* audio clk settings moved to sai2 node
https://lore.kernel.org/linux-arm-kernel/20200604084756.586-1-martin.kepplinger@puri.sm/T/
v1:
https://lore.kernel.org/linux-arm-kernel/20200514155737.12160-1-martin.kepplinger@puri.sm/
arch/arm64/boot/dts/freescale/Makefile | 2 +
.../boot/dts/freescale/imx8mq-librem5-r2.dts | 29 +
.../boot/dts/freescale/imx8mq-librem5-r3.dts | 27 +
.../boot/dts/freescale/imx8mq-librem5.dtsi | 1105 +++++++++++++++++
4 files changed, 1163 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-librem5-r2.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index a39f0a1723e0..97335205b600 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -35,6 +35,8 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r2.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r3.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-nitrogen.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-phanbell.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-pico-pi.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-r2.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-r2.dts
new file mode 100644
index 000000000000..d77fc5df3f06
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-r2.dts
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2020 Purism SPC <kernel@...i.sm>
+//
+// Librem 5 Chestnut
+
+/dts-v1/;
+
+#include "imx8mq-librem5.dtsi"
+
+/ {
+ model = "Purism Librem 5r2";
+ compatible = "purism,librem5r2", "purism,librem5", "fsl,imx8mq";
+};
+
+&bq25895 {
+ ti,battery-regulation-voltage = <4192000>; /* uV */
+ ti,charge-current = <1600000>; /* uA */
+ ti,termination-current = <66000>; /* uA */
+};
+
+&accel_gyro {
+ mount-matrix = "1", "0", "0",
+ "0", "-1", "0",
+ "0", "0", "1";
+};
+
+&proximity {
+ proximity-near-level = <220>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dts
new file mode 100644
index 000000000000..6704ea2c72a3
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dts
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2020 Purism SPC <kernel@...i.sm>
+
+/dts-v1/;
+
+#include "imx8mq-librem5.dtsi"
+
+/ {
+ model = "Purism Librem 5r3";
+ compatible = "purism,librem5r3", "purism,librem5", "fsl,imx8mq";
+};
+
+&accel_gyro {
+ mount-matrix = "1", "0", "0",
+ "0", "1", "0",
+ "0", "0", "-1";
+};
+
+&bq25895 {
+ ti,battery-regulation-voltage = <4200000>; /* uV */
+ ti,charge-current = <1500000>; /* uA */
+ ti,termination-current = <144000>; /* uA */
+};
+
+&proximity {
+ proximity-near-level = <25>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
new file mode 100644
index 000000000000..c3e290703fe8
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
@@ -0,0 +1,1105 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018-2020 Purism SPC
+ */
+
+/dts-v1/;
+
+#include "dt-bindings/input/input.h"
+#include "dt-bindings/pwm/pwm.h"
+#include "dt-bindings/usb/pd.h"
+#include "imx8mq.dtsi"
+
+/ {
+ model = "Purism Librem 5";
+ compatible = "purism,librem5", "fsl,imx8mq";
+
+ backlight_dsi: backlight-dsi {
+ compatible = "led-backlight";
+ leds = <&led_backlight>;
+ };
+
+ pmic_osc: clock-pmic {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "pmic_osc";
+ };
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_keys>;
+
+ vol-down {
+ label = "VOL_DOWN";
+ gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+
+ vol-up {
+ label = "VOL_UP";
+ gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+ };
+
+ reg_aud_1v8: regulator-audio-1v8 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audiopwr>;
+ regulator-name = "AUDIO_PWR_EN";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_gnss: regulator-gnss {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gnsspwr>;
+ regulator-name = "GNSS";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 12 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_hub: regulator-hub {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hub_pwr>;
+ regulator-name = "HUB";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_lcd_3v4: regulator-lcd-3v4 {
+ compatible = "regulator-fixed";
+ regulator-name = "LCD_3V4";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dsibiasen>;
+ vin-supply = <®_vsys_3v4>;
+ gpio = <&gpio1 20 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_vdd_sen: regulator-vdd-sen {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_SEN";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_vdd_3v3: regulator-vdd-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_vdd_1v8: regulator-vdd-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ reg_vsys_3v4: regulator-vsys-3v4 {
+ compatible = "regulator-fixed";
+ regulator-name = "VSYS_3V4";
+ regulator-min-microvolt = <3400000>;
+ regulator-max-microvolt = <3400000>;
+ regulator-always-on;
+ };
+
+ reg_wifi_3v3: regulator-wifi-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3_WIFI";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hp>;
+ simple-audio-card,name = "Librem 5";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,widgets =
+ "Headphone", "Headphones",
+ "Microphone", "Headset Mic",
+ "Microphone", "Digital Mic",
+ "Speaker", "Speaker";
+ simple-audio-card,routing =
+ "Headphones", "HPOUTL",
+ "Headphones", "HPOUTR",
+ "Speaker", "SPKOUTL",
+ "Speaker", "SPKOUTR",
+ "Headset Mic", "MICBIAS",
+ "IN3R", "Headset Mic",
+ "DMICDAT", "Digital Mic";
+ simple-audio-card,hp-det-gpio = <&gpio3 9 GPIO_ACTIVE_HIGH>;
+
+ simple-audio-card,cpu {
+ sound-dai = <&sai2>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&codec>;
+ clocks = <&clk IMX8MQ_CLK_SAI2_ROOT>;
+ frame-master;
+ bitclock-master;
+ };
+ };
+
+ sound-wwan {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "Modem";
+ simple-audio-card,format = "i2s";
+
+ simple-audio-card,cpu {
+ sound-dai = <&sai6>;
+ frame-inversion;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&bm818_codec>;
+ frame-master;
+ bitclock-master;
+ };
+ };
+
+ bm818_codec: sound-wwan-codec {
+ compatible = "broadmobi,bm818", "option,gtm601";
+ #sound-dai-cells = <0>;
+ };
+
+ vibrator {
+ compatible = "pwm-vibrator";
+ pwms = <&pwm1 0 1000000000 0>;
+ pwm-names = "enable";
+ vcc-supply = <®_vdd_3v3>;
+ };
+};
+
+&A53_0 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_1 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_2 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_3 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&ddrc {
+ operating-points-v2 = <&ddrc_opp_table>;
+
+ ddrc_opp_table: ddrc-opp-table {
+ compatible = "operating-points-v2";
+
+ opp-25M {
+ opp-hz = /bits/ 64 <25000000>;
+ };
+
+ opp-100M {
+ opp-hz = /bits/ 64 <100000000>;
+ };
+
+ opp-800M {
+ opp-hz = /bits/ 64 <800000000>;
+ };
+ };
+};
+
+&dphy {
+ status = "okay";
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ nor_flash: flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ };
+};
+
+&gpio1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic_5v>;
+
+ pmic-5v {
+ gpio-hog;
+ gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+ input;
+ };
+};
+
+&iomuxc {
+ pinctrl_audiopwr: audiopwrgrp {
+ fsl,pins = <
+ /* AUDIO_POWER_EN_3V3 */
+ MX8MQ_IOMUXC_GPIO1_IO04_GPIO1_IO4 0x83
+ >;
+ };
+
+ pinctrl_bl: blgrp {
+ fsl,pins = <
+ /* BACKLINGE_EN */
+ MX8MQ_IOMUXC_NAND_DQS_GPIO3_IO14 0x83
+ >;
+ };
+
+ pinctrl_charger_in: chargeringrp {
+ fsl,pins = <
+ /* CHRG_INT */
+ MX8MQ_IOMUXC_NAND_CE2_B_GPIO3_IO3 0x00
+ /* CHG_STATUS_B */
+ MX8MQ_IOMUXC_NAND_ALE_GPIO3_IO0 0x80
+ >;
+ };
+
+ pinctrl_dsibiasen: dsibiasengrp {
+ fsl,pins = <
+ /* DSI_BIAS_EN */
+ MX8MQ_IOMUXC_ENET_TD1_GPIO1_IO20 0x83
+ >;
+ };
+
+ pinctrl_dsien: dsiengrp {
+ fsl,pins = <
+ /* DSI_EN_3V3 */
+ MX8MQ_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x83
+ >;
+ };
+
+ pinctrl_ecspi1: ecspigrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x83
+ MX8MQ_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x83
+ MX8MQ_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x19
+ MX8MQ_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x83
+ >;
+ };
+
+ pinctrl_gauge: gaugegrp {
+ fsl,pins = <
+ /* BAT_LOW */
+ MX8MQ_IOMUXC_SAI5_RXC_GPIO3_IO20 0x80
+ >;
+ };
+
+ pinctrl_gnsspwr: gnsspwrgrp {
+ fsl,pins = <
+ /* GPS3V3_EN */
+ MX8MQ_IOMUXC_NAND_DATA06_GPIO3_IO12 0x83
+ >;
+ };
+
+ pinctrl_haptic: hapticgrp {
+ fsl,pins = <
+ /* MOTO */
+ MX8MQ_IOMUXC_SPDIF_EXT_CLK_PWM1_OUT 0x83
+ >;
+ };
+
+ pinctrl_hp: hpgrp {
+ fsl,pins = <
+ /* HEADPHONE_DET_1V8 */
+ MX8MQ_IOMUXC_NAND_DATA03_GPIO3_IO9 0x180
+ >;
+ };
+
+ pinctrl_hub_pwr: hubpwrgrp {
+ fsl,pins = <
+ /* HUB_PWR_3V3_EN */
+ MX8MQ_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x83
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x40000026
+ MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x40000026
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x40000026
+ MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x40000026
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000026
+ MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000026
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C4_SCL_I2C4_SCL 0x40000026
+ MX8MQ_IOMUXC_I2C4_SDA_I2C4_SDA 0x40000026
+ >;
+ };
+
+ pinctrl_keys: keysgrp {
+ fsl,pins = <
+ /* VOL- */
+ MX8MQ_IOMUXC_ENET_MDIO_GPIO1_IO17 0x01C0
+ /* VOL+ */
+ MX8MQ_IOMUXC_ENET_MDC_GPIO1_IO16 0x01C0
+ >;
+ };
+
+ pinctrl_led_b: ledbgrp {
+ fsl,pins = <
+ /* LED_B */
+ MX8MQ_IOMUXC_GPIO1_IO13_PWM2_OUT 0x06
+ >;
+ };
+
+ pinctrl_led_g: ledggrp {
+ fsl,pins = <
+ /* LED_G */
+ MX8MQ_IOMUXC_SAI3_MCLK_PWM4_OUT 0x06
+ >;
+ };
+
+ pinctrl_led_r: ledrgrp {
+ fsl,pins = <
+ /* LED_R */
+ MX8MQ_IOMUXC_SPDIF_TX_PWM3_OUT 0x06
+ >;
+ };
+
+ pinctrl_mag: maggrp {
+ fsl,pins = <
+ /* INT_MAG */
+ MX8MQ_IOMUXC_SAI5_RXD1_GPIO3_IO22 0x80
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ /* PMIC_NINT */
+ MX8MQ_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x80
+ >;
+ };
+
+ pinctrl_pmic_5v: pmic5vgrp {
+ fsl,pins = <
+ /* PMIC_5V */
+ MX8MQ_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x80
+ >;
+ };
+
+ pinctrl_prox: proxgrp {
+ fsl,pins = <
+ /* INT_LIGHT */
+ MX8MQ_IOMUXC_NAND_DATA01_GPIO3_IO7 0x80
+ >;
+ };
+
+ pinctrl_rtc: rtcgrp {
+ fsl,pins = <
+ /* RTC_INT */
+ MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x80
+ >;
+ };
+
+ pinctrl_sai2: sai2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0 0xd6
+ MX8MQ_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC 0xd6
+ MX8MQ_IOMUXC_SAI2_MCLK_SAI2_MCLK 0xd6
+ MX8MQ_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0 0xd6
+ MX8MQ_IOMUXC_SAI2_TXC_SAI2_TX_BCLK 0xd6
+ >;
+ };
+
+ pinctrl_sai6: sai6grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SAI1_RXD5_SAI6_RX_DATA0 0xd6
+ MX8MQ_IOMUXC_SAI1_RXD6_SAI6_RX_SYNC 0xd6
+ MX8MQ_IOMUXC_SAI1_TXD4_SAI6_RX_BCLK 0xd6
+ MX8MQ_IOMUXC_SAI1_TXD5_SAI6_TX_DATA0 0xd6
+ >;
+ };
+
+ pinctrl_tcpc: tcpcgrp {
+ fsl,pins = <
+ /* TCPC_INT */
+ MX8MQ_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x01C0
+ >;
+ };
+
+ pinctrl_typec: typecgrp {
+ fsl,pins = <
+ /* TYPEC_MUX_EN */
+ MX8MQ_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x83
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49
+ MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x49
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x49
+ MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x49
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX 0x49
+ MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX 0x49
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ECSPI2_SCLK_UART4_DCE_RX 0x49
+ MX8MQ_IOMUXC_ECSPI2_MOSI_UART4_DCE_TX 0x49
+ MX8MQ_IOMUXC_ECSPI2_MISO_UART4_DCE_CTS_B 0x49
+ MX8MQ_IOMUXC_ECSPI2_SS0_UART4_DCE_RTS_B 0x49
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x83
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x8d
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xcd
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xcd
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xcd
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xcd
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xcd
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xcd
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xcd
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xcd
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xcd
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x8d
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x9f
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xdf
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xdf
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xdf
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xdf
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xdf
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xdf
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xdf
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xdf
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xdf
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x9f
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x80
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3
+ MX8MQ_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x80
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x8d
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcd
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcd
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcd
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcd
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcd
+ MX8MQ_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x80
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x9f
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcf
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcf
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcf
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcf
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcf
+ MX8MQ_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ /* nWDOG */
+ MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x1f
+ >;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <387000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ typec_pd: usb-pd@3f {
+ compatible = "ti,tps6598x";
+ reg = <0x3f>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_typec>, <&pinctrl_tcpc>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+
+ connector {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ usb_con_hs: endpoint {
+ remote-endpoint = <&typec_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ usb_con_ss: endpoint {
+ remote-endpoint = <&typec_ss>;
+ };
+ };
+ };
+ };
+ };
+
+ pmic: pmic@4b {
+ compatible = "rohm,bd71837";
+ reg = <0x4b>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+ clocks = <&pmic_osc>;
+ clock-names = "osc";
+ clock-output-names = "pmic_clk";
+ interrupt-parent = <&gpio1>;
+ interrupts = <7 GPIO_ACTIVE_LOW>;
+ interrupt-names = "irq";
+ rohm,reset-snvs-powered;
+
+ regulators {
+ buck1_reg: BUCK1 {
+ regulator-name = "BUCK1";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-ramp-delay = <1250>;
+ rohm,dvs-run-voltage = <900000>;
+ rohm,dvs-idle-voltage = <850000>;
+ rohm,dvs-suspend-voltage = <800000>;
+ regulator-always-on;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "BUCK2";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-ramp-delay = <1250>;
+ rohm,dvs-run-voltage = <1000000>;
+ rohm,dvs-idle-voltage = <900000>;
+ regulator-always-on;
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "BUCK3";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ rohm,dvs-run-voltage = <900000>;
+ regulator-always-on;
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "BUCK4";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ rohm,dvs-run-voltage = <1000000>;
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "BUCK5";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ };
+
+ buck6_reg: BUCK6 {
+ regulator-name = "BUCK6";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ buck7_reg: BUCK7 {
+ regulator-name = "BUCK7";
+ regulator-min-microvolt = <1605000>;
+ regulator-max-microvolt = <1995000>;
+ regulator-always-on;
+ };
+
+ buck8_reg: BUCK8 {
+ regulator-name = "BUCK8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ };
+
+ ldo1_reg: LDO1 {
+ regulator-name = "LDO1";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ /* leave on for snvs power button */
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "LDO2";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ /* leave on for snvs power button */
+ regulator-always-on;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "LDO3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "LDO4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo5_reg: LDO5 {
+ /* VDD_PHY_0V9 - MIPI and HDMI domains */
+ regulator-name = "LDO5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ ldo6_reg: LDO6 {
+ /* VDD_PHY_0V9 - MIPI, HDMI and USB domains */
+ regulator-name = "LDO6";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo7_reg: LDO7 {
+ /* VDD_PHY_3V3 - USB domain */
+ regulator-name = "LDO7";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+
+ rtc@68 {
+ compatible = "microcrystal,rv4162";
+ reg = <0x68>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rtc>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <387000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ magnetometer@1e {
+ compatible = "st,lsm9ds1-magn";
+ reg = <0x1e>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mag>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
+ vdd-supply = <®_vdd_sen>;
+ vddio-supply = <®_vdd_1v8>;
+ };
+
+ regulator@3e {
+ compatible = "tps65132";
+ reg = <0x3e>;
+
+ outp {
+ regulator-name = "LCD_AVDD";
+ vin-supply = <®_lcd_3v4>;
+ };
+
+ outn {
+ regulator-name = "LCD_AVEE";
+ vin-supply = <®_lcd_3v4>;
+ };
+ };
+
+ proximity: prox@60 {
+ compatible = "vishay,vcnl4040";
+ reg = <0x60>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_prox>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ accel_gyro: accel-gyro@6a {
+ compatible = "st,lsm9ds1-imu";
+ reg = <0x6a>;
+ vdd-supply = <®_vdd_sen>;
+ vddio-supply = <®_vdd_1v8>;
+ };
+};
+
+&i2c3 {
+ clock-frequency = <387000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ codec: audio-codec@1a {
+ compatible = "wlf,wm8962";
+ reg = <0x1a>;
+ clocks = <&clk IMX8MQ_CLK_SAI2_ROOT>;
+ assigned-clocks = <&clk IMX8MQ_CLK_SAI2>;
+ assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>;
+ assigned-clock-rates = <24576000>;
+ #sound-dai-cells = <0>;
+ mic-cfg = <0x200>;
+ DCVDD-supply = <®_aud_1v8>;
+ DBVDD-supply = <®_aud_1v8>;
+ AVDD-supply = <®_aud_1v8>;
+ CPVDD-supply = <®_aud_1v8>;
+ MICVDD-supply = <®_aud_1v8>;
+ PLLVDD-supply = <®_aud_1v8>;
+ SPKVDD1-supply = <®_vsys_3v4>;
+ SPKVDD2-supply = <®_vsys_3v4>;
+ gpio-cfg = <
+ 0x0000 /* n/c */
+ 0x0001 /* gpio2, 1: default */
+ 0x0013 /* gpio3, 2: dmicclk */
+ 0x0000 /* n/c, 3: default */
+ 0x8014 /* gpio5, 4: dmic_dat */
+ 0x0000 /* gpio6, 5: default */
+ >;
+ };
+
+ backlight@36 {
+ compatible = "ti,lm36922";
+ reg = <0x36>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_bl>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ enable-gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+ vled-supply = <®_vsys_3v4>;
+ ti,ovp-microvolt = <25000000>;
+
+ led_backlight: led@0 {
+ reg = <0>;
+ label = ":backlight";
+ linux,default-trigger = "backlight";
+ led-max-microamp = <20000>;
+ };
+ };
+
+ touchscreen@38 {
+ compatible = "edt,edt-ft5506";
+ reg = <0x38>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <27 IRQ_TYPE_EDGE_FALLING>;
+ touchscreen-size-x = <720>;
+ touchscreen-size-y = <1440>;
+ };
+};
+
+&i2c4 {
+ clock-frequency = <387000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ status = "okay";
+
+ bat: fuel-gauge@36 {
+ compatible = "maxim,max17055";
+ reg = <0x36>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gauge>;
+ maxim,over-heat-temp = <700>;
+ maxim,over-volt = <4500>;
+ maxim,rsns-microohm = <5000>;
+ };
+
+ bq25895: charger@6a {
+ compatible = "ti,bq25895", "ti,bq25890";
+ reg = <0x6a>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_charger_in>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+ phys = <&usb3_phy0>;
+ ti,precharge-current = <130000>; /* uA */
+ ti,minimum-sys-voltage = <3700000>; /* uV */
+ ti,boost-voltage = <5000000>; /* uV */
+ ti,boost-max-current = <500000>; /* uA */
+ ti,use-vinmin-threshold = <1>; /* enable VINDPM */
+ ti,vinmin-threshold = <3900000>; /* uV */
+ monitored-battery = <&bat>;
+ };
+};
+
+&pgc_gpu {
+ power-supply = <&buck3_reg>;
+};
+
+&pgc_mipi {
+ power-supply = <&ldo5_reg>;
+};
+
+&pgc_vpu {
+ power-supply = <&buck4_reg>;
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_haptic>;
+ status = "okay";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_led_b>;
+ status = "okay";
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_led_g>;
+ status = "okay";
+};
+
+&pwm4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_led_r>;
+ status = "okay";
+};
+
+&sai2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai2>;
+ assigned-clocks = <&clk IMX8MQ_CLK_SAI2>;
+ assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>;
+ assigned-clock-rates = <24576000>;
+ assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL2>;
+ assigned-clock-rates = <786432000>, <722534400>;
+ status = "okay";
+};
+
+&sai6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai6>;
+ assigned-clocks = <&clk IMX8MQ_CLK_SAI6>;
+ assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>;
+ assigned-clock-rates = <24576000>;
+ fsl,sai-synchronous-rx;
+ status = "okay";
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
+&snvs_rtc {
+ status = "disabled";
+};
+
+&uart1 { /* console */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 { /* TPS - GPS - DEBUG */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+
+ gnss {
+ compatible = "globaltop,pa6h";
+ vcc-supply = <®_gnss>;
+ current-speed = <9600>;
+ };
+};
+
+&uart3 { /* SMC */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&uart4 { /* BT */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&usb3_phy0 {
+ status = "okay";
+};
+
+&usb3_phy1 {
+ vbus-supply = <®_hub>;
+ status = "okay";
+};
+
+&usb_dwc3_0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dr_mode = "otg";
+ snps,dis_u3_susphy_quirk;
+ status = "okay";
+
+ port@0 {
+ reg = <0>;
+
+ typec_hs: endpoint {
+ remote-endpoint = <&usb_con_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ typec_ss: endpoint {
+ remote-endpoint = <&usb_con_ss>;
+ };
+ };
+};
+
+&usb_dwc3_1 {
+ dr_mode = "host";
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip USB2642 */
+ hub@1 {
+ compatible = "usb424,2640";
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mass-storage@1 {
+ compatible = "usb424,4041";
+ reg = <1>;
+ };
+ };
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ bus-width = <8>;
+ vmmc-supply = <®_vdd_3v3>;
+ power-supply = <®_vdd_1v8>;
+ non-removable;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+ bus-width = <4>;
+ vmmc-supply = <®_wifi_3v3>;
+ cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ wakeup-source;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
--
2.20.1
Powered by blists - more mailing lists