Message-ID: <20200831220030.GA207013@xps15>
Date:   Mon, 31 Aug 2020 16:00:30 -0600
From:   Mathieu Poirier <mathieu.poirier@...aro.org>
To:     Al Grant <Al.Grant@....com>
Cc:     Qi Liu <liuqi115@...wei.com>,
        "gregkh@...uxfoundation.org" <gregkh@...uxfoundation.org>,
        "coresight@...ts.linaro.org" <coresight@...ts.linaro.org>,
        "linuxarm@...wei.com" <linuxarm@...wei.com>,
        "linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
        "linux-arm-kernel@...ts.infradead.org" 
        <linux-arm-kernel@...ts.infradead.org>,
        "mike.leach@...aro.org" <mike.leach@...aro.org>
Subject: Re: [RFC PATCH v2] coresight: etm4x: Modify core-commit of cpu to
 avoid the overflow of HiSilicon ETM

On Fri, Aug 28, 2020 at 09:00:16AM +0000, Al Grant wrote:
> Hi Mathieu and CS maintainers,
> 
> > Hi Liu,
> > 
> > On Wed, Aug 19, 2020 at 04:06:37PM +0800, Qi Liu wrote:
> > > When too much trace information is generated on-chip, the ETM will
> > > overflow, and cause data loss. This is a common phenomenon on ETM
> > > devices.
> > >
> > > But sometimes we do not want to lose performance trace data, so we
> > > suppress the speed of instructions sent from CPU core to ETM to avoid
> > > the overflow of ETM.
> > >
> > > Signed-off-by: Qi Liu <liuqi115@...wei.com>
> > > ---
> > >
> > > Changes since v1:
> > > - ETM on HiSilicon Hip09 platform supports backpressure, so does not
> > > need to modify core commit.
> > >
> > >  drivers/hwtracing/coresight/coresight-etm4x.c | 43
> > > +++++++++++++++++++++++++++
> > >  1 file changed, 43 insertions(+)
> > >
> > > diff --git a/drivers/hwtracing/coresight/coresight-etm4x.c
> > > b/drivers/hwtracing/coresight/coresight-etm4x.c
> > > index 7797a57..7641f89 100644
> > > --- a/drivers/hwtracing/coresight/coresight-etm4x.c
> > > +++ b/drivers/hwtracing/coresight/coresight-etm4x.c
> > > @@ -43,6 +43,10 @@ MODULE_PARM_DESC(boot_enable, "Enable tracing
> > on boot");
> > >  #define PARAM_PM_SAVE_NEVER	  1 /* never save any state */
> > >  #define PARAM_PM_SAVE_SELF_HOSTED 2 /* save self-hosted state only */
> > >
> > > +#define CORE_COMMIT_CLEAR	0x3000
> > > +#define CORE_COMMIT_SHIFT	12
> > > +#define HISI_ETM_AMBA_ID_V1	0x000b6d01
> > > +
> > >  static int pm_save_enable = PARAM_PM_SAVE_FIRMWARE;
> > > module_param(pm_save_enable, int, 0444);
> > > MODULE_PARM_DESC(pm_save_enable, @@ -104,11 +108,40 @@ struct
> > > etm4_enable_arg {
> > >  	int rc;
> > >  };
> > >
> > > +static void etm4_cpu_actlr1_cfg(void *info) {
> > > +	struct etm4_enable_arg *arg = (struct etm4_enable_arg *)info;
> > > +	u64 val;
> > > +
> > > +	asm volatile("mrs %0,s3_1_c15_c2_5" : "=r"(val));
> > > +	val &= ~CORE_COMMIT_CLEAR;
> > > +	val |= arg->rc << CORE_COMMIT_SHIFT;
> > > +	asm volatile("msr s3_1_c15_c2_5,%0" : : "r"(val)); }
> > > +
> > > +static void etm4_config_core_commit(int cpu, int val) {
> > > +	struct etm4_enable_arg arg = {0};
> > > +
> > > +	arg.rc = val;
> > > +	smp_call_function_single(cpu, etm4_cpu_actlr1_cfg, &arg, 1);
> > 
> > Function etm4_enable/disable_hw() are already running on the CPU they are
> > supposed to so no need to call smp_call_function_single().
> > 
> > > +}
> > > +
> > >  static int etm4_enable_hw(struct etmv4_drvdata *drvdata)  {
> > >  	int i, rc;
> > > +	struct amba_device *adev;
> > >  	struct etmv4_config *config = &drvdata->config;
> > >  	struct device *etm_dev = &drvdata->csdev->dev;
> > > +	struct device *dev = drvdata->csdev->dev.parent;
> > > +
> > > +	adev = container_of(dev, struct amba_device, dev);
> > > +	/*
> > > +	 * If ETM device is HiSilicon ETM device, reduce the
> > > +	 * core-commit to avoid ETM overflow.
> > > +	 */
> > > +	if (adev->periphid == HISI_ETM_AMBA_ID_V1)
> > 
> > Do you have any documentation on this back pressure feature?  I doubt this is
> > specific to Hip09 platform and as such would prefer to have a more generic
> > approach that works on any platform that supports it.
> 
> It's not a standard Arm architecture feature, this is a model-specific register.
> Some cores may be able to throttle throughput under user control,
> but this isn't standardized. It may (as in this case) be something that you
> want to enable whenever you enable ETM - and, I guess, disable whenever
> you disable ETM. It's a bit unclean to have model-specific code in the main
> ETM driver, and names like CORE_COMMIT_CLEAR really ought to be more
> specific, but I don't see that it's more ugly than the model-specific code in
> e.g. arch/arm64/kernel/perf_event.c or its equivalent on other architectures.
> 
> Ideally, a core that has an inherent difficulty generating ETM at full speed,
> i.e. where the ETM can't keep up with the core pipeline, would reduce
> commit rate automatically, and some already do. So if this core needs it
> to be done manually via a system register, we might allow that in the
> same way as we might allow other core-specific actions that need to be
> done to enable ETM.
> 
> There are of course issues with trace overflow at all stages up to and
> including harvesting trace from buffers into perf.data (for which solutions
> might involve DVFS, trace strobing, scheduling etc.), and I am assuming
> this patch is not addressing those but dealing with a very specific concern
> about overflow within the core and its ETM.

Thanks for chiming in on this - very valuable input.

Mathieu

> 
> Al
> 
> 
> > 
> > Anyone on the CS mailing list that knows what this is about?
> > 
> > Thanks,
> > Mathieu
> > 
> > > +		etm4_config_core_commit(drvdata->cpu, 1);
> > >
> > >  	CS_UNLOCK(drvdata->base);
> > >
> > > @@ -472,10 +505,20 @@ static void etm4_disable_hw(void *info)  {
> > >  	u32 control;
> > >  	struct etmv4_drvdata *drvdata = info;
> > > +	struct device *dev = drvdata->csdev->dev.parent;
> > >  	struct etmv4_config *config = &drvdata->config;
> > >  	struct device *etm_dev = &drvdata->csdev->dev;
> > > +	struct amba_device *adev;
> > >  	int i;
> > >
> > > +	adev = container_of(dev, struct amba_device, dev);
> > > +	/*
> > > +	 * If ETM device is HiSilicon ETM device, resume the
> > > +	 * core-commit after ETM trace is complete.
> > > +	 */
> > > +	if (adev->periphid == HISI_ETM_AMBA_ID_V1)
> > > +		etm4_config_core_commit(drvdata->cpu, 0);
> > > +
> > >  	CS_UNLOCK(drvdata->base);
> > >
> > >  	if (!drvdata->skip_power_up) {
> > > --
> > > 2.8.1
> > >
> > _______________________________________________
> > CoreSight mailing list
> > CoreSight@...ts.linaro.org
> > https://lists.linaro.org/mailman/listinfo/coresight

Powered by blists - more mailing lists