Date:   Fri, 4 Sep 2020 17:45:12 -0700
From:   Moritz Fischer <mdf@...nel.org>
To:     Xu Yilun <yilun.xu@...el.com>
Cc:     mdf@...nel.org, linux-fpga@...r.kernel.org,
        linux-kernel@...r.kernel.org, trix@...hat.com, lgoncalv@...hat.com,
        Wu Hao <hao.wu@...el.com>,
        Matthew Gerlach <matthew.gerlach@...ux.intel.com>,
        Russ Weight <russell.h.weight@...el.com>
Subject: Re: [PATCH v7 3/3] fpga: dfl: add support for N3000 Nios private
 feature

Hi Xu,

On Wed, Aug 19, 2020 at 03:45:21PM +0800, Xu Yilun wrote:
> This patch adds support for the Nios handshake private feature on Intel
> PAC (Programmable Acceleration Card) N3000.
> 
> The Nios is the embedded processor on the FPGA card. This private feature
> provides a handshake interface to FPGA Nois firmware, which receives
FPGA *NIOS* or *Nios* I think ;-)
> retimer configuration command from host and executes via an internal SPI
> master (spi-altera). When Nios finishes the configuration, host takes over
> the ownership of the SPI master to control an Intel MAX10 BMC (Board
> Management Controller) Chip on the SPI bus.
> 
> For Nios firmware handshake part, this driver requests the retimer
> configuration for Nios with parameters from module param, and adds some
> sysfs nodes for user to query the onboard retimer's working mode and
> Nios firmware version.
> 
> For SPI part, this driver adds a spi-altera platform device as well as
> the MAX10 BMC spi slave info. A spi-altera driver will be matched to
> handle the following SPI work.
> 
> Signed-off-by: Xu Yilun <yilun.xu@...el.com>
> Signed-off-by: Wu Hao <hao.wu@...el.com>
> Signed-off-by: Matthew Gerlach <matthew.gerlach@...ux.intel.com>
> Signed-off-by: Russ Weight <russell.h.weight@...el.com>
> Reviewed-by: Tom Rix <trix@...hat.com>
> Acked-by: Wu Hao <hao.wu@...el.com>
> ---
> v3: Add the doc for this driver
>     Minor fixes for comments from Tom
> v4: Move the err log in regmap implementation, and delete
>      n3000_nios_writel/readl(), they have nothing to wrapper now.
>     Some minor fixes and comments improvement.
> v5: Fix the output of fec_mode sysfs inf to "no" on 10G configuration,
>      cause no FEC mode could be configured for 10G.
>     Rename the dfl_n3000_nios_* to n3000_nios_*
>     Improves comments.
> v6: Fix the output of fec_mode sysfs inf to "not supported" if in 10G,
>      or the firmware version major < 3.
>     Minor fixes and improves comments.
> v7: Improves comments.
> ---
>  .../ABI/testing/sysfs-bus-dfl-devices-n3000-nios   |  21 +
>  Documentation/fpga/dfl-n3000-nios.rst              |  80 +++
>  Documentation/fpga/index.rst                       |   1 +
>  drivers/fpga/Kconfig                               |  11 +
>  drivers/fpga/Makefile                              |   2 +
>  drivers/fpga/dfl-n3000-nios.c                      | 542 +++++++++++++++++++++
>  6 files changed, 657 insertions(+)
>  create mode 100644 Documentation/ABI/testing/sysfs-bus-dfl-devices-n3000-nios
>  create mode 100644 Documentation/fpga/dfl-n3000-nios.rst
>  create mode 100644 drivers/fpga/dfl-n3000-nios.c
> 
> diff --git a/Documentation/ABI/testing/sysfs-bus-dfl-devices-n3000-nios b/Documentation/ABI/testing/sysfs-bus-dfl-devices-n3000-nios
> new file mode 100644
> index 0000000..ce5b474
> --- /dev/null
> +++ b/Documentation/ABI/testing/sysfs-bus-dfl-devices-n3000-nios
> @@ -0,0 +1,21 @@
> +What:		/sys/bus/dfl/devices/dfl_dev.X/fec_mode
> +Date:		Aug 2020
> +KernelVersion:	5.10
> +Contact:	Xu Yilun <yilun.xu@...el.com>
> +Description:	Read-only. It returns the FEC mode of the 25G links of the
> +		ethernet retimers configured by NIOS firmware. "rs" for Reed
> +		Solomon FEC, "kr" for Fire Code FEC, "no" for NO FEC.
> +		"not supported" if the FEC mode setting is not supported, this
> +		happens when the Nios firmware version major < 3, or no link is
> +		configured to 25G. The FEC mode could be set by module
> +		parameters, but it could only be set once after the board
> +		powers up.
> +		Format: string
> +
> +What:		/sys/bus/dfl/devices/dfl_dev.X/nios_fw_version
> +Date:		Aug 2020
> +KernelVersion:	5.10
> +Contact:	Xu Yilun <yilun.xu@...el.com>
> +Description:	Read-only. It returns the version of the NIOS firmware in FPGA.
> +		Its format is "major.minor.patch".
> +		Format: %x.%x.%x
> diff --git a/Documentation/fpga/dfl-n3000-nios.rst b/Documentation/fpga/dfl-n3000-nios.rst
> new file mode 100644
> index 0000000..72dd600
> --- /dev/null
> +++ b/Documentation/fpga/dfl-n3000-nios.rst
> @@ -0,0 +1,80 @@
> +.. SPDX-License-Identifier: GPL-2.0
> +
> +=================================
> +N3000 Nios Private Feature Driver
> +=================================
> +
> +The N3000 Nios driver supports for the Nios handshake private feature on Intel
> +PAC (Programmable Acceleration Card) N3000.
> +
> +The Nios is the embedded processor in the FPGA, it will configure the 2 onboard
> +ethernet retimers on power up. This private feature provides a handshake
> +interface to FPGA Nios firmware, which receives the ethernet retimer
> +configuration command from host and does the configuration via an internal SPI
> +master (spi-altera). When Nios finishes the configuration, host takes over the
> +ownership of the SPI master to control an Intel MAX10 BMC (Board Management
> +Controller) Chip on the SPI bus.
> +
> +So the driver does 2 major tasks on probe, uses the Nios firmware to configure
> +the ethernet retimer, and then creates a spi master platform device with the
> +MAX10 device info in spi_board_info.
> +
> +
> +Configuring the ethernet retimer
> +================================
> +
> +The Intel PAC N3000 is a FPGA based SmartNIC platform which could be programmed
> +to various configurations (with different link numbers and speeds, e.g. 8x10G,
> +4x25G ...). And the retimer chips should also be configured correspondingly by
> +Nios firmware. There are 2 retimer chips on the board, each of them supports 4
> +links. For example, in 8x10G configuration, the 2 retimer chips are both set to
> +4x10G mode, while in 4x25G configuration, retimer A is set to 4x25G and retimer
> +B is in reset. For now, the Nios firmware only supports 10G and 25G mode
> +setting for the retimer chips.
Make sure your API above exposes all of that.
> +
> +For all 25G links, their FEC (Forward Error Correction) mode could be further
> +configured by Nios firmware for user's requirement. For 10G links, they don't
> +have the FEC mode at all, the firmware ignores the FEC mode setting for them.
> +The FEC setting is not supported if the firmware version major < 3.
> +
> +The retimer configuration can only be done once after the board powers up, the
> +Nios firmware will not accept second configuration afterward. So it is not
> +proper for the driver to create a RW sysfs node for the FEC mode. A better way
> +is that the driver accepts a module parameter for the FEC mode, and does the
> +retimer configuration on driver probe, it also creates a RO sysfs node for the
> +FEC mode query.
> +
> +Module Parameters
> +=================
> +
> +The N3000 Nios driver supports the following module parameters:
> +
> +* fec_mode: string
> +  Require the Nios firmware to set the FEC mode for all 25G links of the
> +  ethernet retimers. The Nios firmware configures all these links with the same
> +  FEC mode. The possible values of fec_mode could be:
> +
> +  - "rs": Reed Solomon FEC (default)
> +  - "kr": Fire Code FEC
> +  - "no": No FEC
> +
> +  Since the firmware doesn't accept second configuration, The FEC mode will not
> +  be changed if the module is reloaded with a different parameter value.
> +
> +  The parameter has no effect for 10G links. It has no effect to all the links
> +  if firmware version major < 3.
> +
> +
> +Sysfs Attributes
> +================
> +
> +The driver creates the sysfs file in /sys/bus/dfl/devices/dfl_dev.X/
> +
> +* fec_mode:
> +  Read-only. It shows the FEC mode of the 25G links of the ethernet retimers.
> +  The possible values are the same as the fec_mode module parameter. An extra
> +  value "not supported" is returned if firmware version major < 3, or no link
> +  is configured to 25G.

This seems somewhat duplicate, runs the risk to get out of sync with the
ABI doc?

> +
> +* nios_fw_version:
> +  Read-only. It shows the version of the Nios firmware in FPGA.
> diff --git a/Documentation/fpga/index.rst b/Documentation/fpga/index.rst
> index f80f956..5fd3c37 100644
> --- a/Documentation/fpga/index.rst
> +++ b/Documentation/fpga/index.rst
> @@ -8,6 +8,7 @@ fpga
>      :maxdepth: 1
>  
>      dfl
> +    dfl-n3000-nios
>  
>  .. only::  subproject and html
>  
> diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
> index 7cd5a29..38c7130 100644
> --- a/drivers/fpga/Kconfig
> +++ b/drivers/fpga/Kconfig
> @@ -191,6 +191,17 @@ config FPGA_DFL_AFU
>  	  to the FPGA infrastructure via a Port. There may be more than one
>  	  Port/AFU per DFL based FPGA device.
>  
> +config FPGA_DFL_NIOS_INTEL_PAC_N3000
> +        tristate "FPGA DFL NIOS Driver for Intel PAC N3000"
> +        depends on FPGA_DFL
> +        select REGMAP
> +        help
> +	  This is the driver for the N3000 Nios private feature on Intel
> +	  PAC (Programmable Acceleration Card) N3000. It communicates
> +	  with the embedded Nios processor to configure the retimers on
> +	  the card. It also instantiates the SPI master (spi-altera) for
> +	  the card's BMC (Board Management Controller) control.
> +
>  config FPGA_DFL_PCI
>  	tristate "FPGA DFL PCIe Device Driver"
>  	depends on PCI && FPGA_DFL
> diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
> index d8e21df..18dc9885 100644
> --- a/drivers/fpga/Makefile
> +++ b/drivers/fpga/Makefile
> @@ -44,5 +44,7 @@ dfl-fme-objs += dfl-fme-perf.o
>  dfl-afu-objs := dfl-afu-main.o dfl-afu-region.o dfl-afu-dma-region.o
>  dfl-afu-objs += dfl-afu-error.o
>  
> +obj-$(CONFIG_FPGA_DFL_NIOS_INTEL_PAC_N3000)	+= dfl-n3000-nios.o
> +
>  # Drivers for FPGAs which implement DFL
>  obj-$(CONFIG_FPGA_DFL_PCI)		+= dfl-pci.o
> diff --git a/drivers/fpga/dfl-n3000-nios.c b/drivers/fpga/dfl-n3000-nios.c
> new file mode 100644
> index 0000000..c73ce38
> --- /dev/null
> +++ b/drivers/fpga/dfl-n3000-nios.c
> @@ -0,0 +1,542 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * DFL device driver for Nios private feature on Intel PAC (Programmable
> + * Acceleration Card) N3000
> + *
> + * Copyright (C) 2019-2020 Intel Corporation, Inc.
> + *
> + * Authors:
> + *   Wu Hao <hao.wu@...el.com>
> + *   Xu Yilun <yilun.xu@...el.com>
> + */
> +#include <linux/bitfield.h>
> +#include <linux/errno.h>
> +#include <linux/io.h>
> +#include <linux/io-64-nonatomic-lo-hi.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/stddef.h>
> +#include <linux/spi/altera.h>
> +#include <linux/spi/spi.h>
> +#include <linux/types.h>
> +
> +#include "dfl.h"
> +
> +static char *fec_mode = "rs";
> +module_param(fec_mode, charp, 0444);
> +MODULE_PARM_DESC(fec_mode, "FEC mode of the ethernet retimer on Intel PAC N3000");
> +
> +/* N3000 Nios private feature registers */
> +#define NIOS_SPI_PARAM			0x8
> +#define PARAM_SHIFT_MODE_MSK		BIT_ULL(1)
> +#define PARAM_SHIFT_MODE_MSB		0
> +#define PARAM_SHIFT_MODE_LSB		1
> +#define PARAM_DATA_WIDTH		GENMASK_ULL(7, 2)
> +#define PARAM_NUM_CS			GENMASK_ULL(13, 8)
> +#define PARAM_CLK_POL			BIT_ULL(14)
> +#define PARAM_CLK_PHASE			BIT_ULL(15)
> +#define PARAM_PERIPHERAL_ID		GENMASK_ULL(47, 32)
> +
> +#define NIOS_SPI_CTRL			0x10
> +#define CTRL_WR_DATA			GENMASK_ULL(31, 0)
> +#define CTRL_ADDR			GENMASK_ULL(44, 32)
> +#define CTRL_CMD_MSK			GENMASK_ULL(63, 62)
> +#define CTRL_CMD_NOP			0
> +#define CTRL_CMD_RD			1
> +#define CTRL_CMD_WR			2
> +
> +#define NIOS_SPI_STAT			0x18
> +#define STAT_RD_DATA			GENMASK_ULL(31, 0)
> +#define STAT_RW_VAL			BIT_ULL(32)
> +
> +/* Nios handshake registers, indirect access */
> +#define NIOS_INIT			0x1000
> +#define NIOS_INIT_DONE			BIT(0)
> +#define NIOS_INIT_START			BIT(1)
> +/* Mode for retimer A, link 0, the same below */
> +#define REQ_FEC_MODE_A0_MSK		GENMASK(9, 8)
> +#define REQ_FEC_MODE_A1_MSK		GENMASK(11, 10)
> +#define REQ_FEC_MODE_A2_MSK		GENMASK(13, 12)
> +#define REQ_FEC_MODE_A3_MSK		GENMASK(15, 14)
> +#define REQ_FEC_MODE_B0_MSK		GENMASK(17, 16)
> +#define REQ_FEC_MODE_B1_MSK		GENMASK(19, 18)
> +#define REQ_FEC_MODE_B2_MSK		GENMASK(21, 20)
> +#define REQ_FEC_MODE_B3_MSK		GENMASK(23, 22)
> +#define REQ_FEC_MODE_NO			0x0
> +#define REQ_FEC_MODE_KR			0x1
> +#define REQ_FEC_MODE_RS			0x2
> +
> +#define NIOS_FW_VERSION			0x1004
> +#define NIOS_FW_VERSION_PATCH		GENMASK(23, 20)
> +#define NIOS_FW_VERSION_MINOR		GENMASK(27, 24)
> +#define NIOS_FW_VERSION_MAJOR		GENMASK(31, 28)
> +
> +/* The retimers we use on Intel PAC N3000 is Parkvale, abbreviated to PKVL */
> +#define PKVL_A_MODE_STS			0x1020
> +#define PKVL_B_MODE_STS			0x1024
> +#define PKVL_MODE_STS_GROUP_MSK		GENMASK(15, 8)
> +#define PKVL_MODE_STS_GROUP_OK		0x0
> +#define PKVL_MODE_STS_ID_MSK		GENMASK(7, 0)
> +/* When GROUP MASK field == GROUP_OK  */
> +#define PKVL_MODE_ID_RESET		0x0
> +#define PKVL_MODE_ID_4X10G		0x1
> +#define PKVL_MODE_ID_4X25G		0x2
> +#define PKVL_MODE_ID_2X25G		0x3
> +#define PKVL_MODE_ID_2X25G_2X10G	0x4
> +#define PKVL_MODE_ID_1X25G		0x5
> +
> +#define NS_REGBUS_WAIT_TIMEOUT		10000		/* loop count */
> +#define NIOS_INIT_TIMEOUT		10000000	/* usec */
> +#define NIOS_INIT_TIME_INTV		100000		/* usec */
> +
> +struct n3000_nios {
> +	void __iomem *base;
> +	struct regmap *regmap;
> +	struct device *dev;
> +	struct platform_device *altera_spi;
> +};
> +
> +static ssize_t nios_fw_version_show(struct device *dev,
> +				    struct device_attribute *attr, char *buf)
> +{
> +	struct n3000_nios *ns = dev_get_drvdata(dev);
> +	unsigned int val;
> +	int ret;
> +
> +	ret = regmap_read(ns->regmap, NIOS_FW_VERSION, &val);
> +	if (ret)
> +		return ret;
> +
> +	return sprintf(buf, "%x.%x.%x\n",
> +		       (u8)FIELD_GET(NIOS_FW_VERSION_MAJOR, val),
> +		       (u8)FIELD_GET(NIOS_FW_VERSION_MINOR, val),
> +		       (u8)FIELD_GET(NIOS_FW_VERSION_PATCH, val));
> +}
> +static DEVICE_ATTR_RO(nios_fw_version);
> +
> +#define IS_MODE_STATUS_OK(mode_stat)				\
> +	(FIELD_GET(PKVL_MODE_STS_GROUP_MSK, (mode_stat)) ==	\
> +	 PKVL_MODE_STS_GROUP_OK)
> +
> +#define IS_RETIMER_FEC_SUPPORTED(retimer_mode)	\
> +	((retimer_mode) != PKVL_MODE_ID_RESET &&	\
> +	 (retimer_mode) != PKVL_MODE_ID_4X10G)
> +
> +static int get_retimer_mode(struct n3000_nios *ns, unsigned int mode_stat_reg,
> +			    unsigned int *retimer_mode)
> +{
> +	unsigned int val;
> +	int ret;
> +
> +	ret = regmap_read(ns->regmap, mode_stat_reg, &val);
> +	if (ret)
> +		return ret;
> +
> +	if (!IS_MODE_STATUS_OK(val))
> +		return -EFAULT;
> +
> +	*retimer_mode = FIELD_GET(PKVL_MODE_STS_ID_MSK, val);
> +
> +	return 0;
> +}
> +
> +static ssize_t fec_mode_show(struct device *dev,
> +			     struct device_attribute *attr, char *buf)
> +{
> +	struct n3000_nios *ns = dev_get_drvdata(dev);
> +	unsigned int val, retimer_a_mode, retimer_b_mode, fec_mode;
Can you make this reverse x-mas tree if possible?
> +	int ret;
> +
> +	/* FEC mode setting is not supported in early FW versions */
> +	ret = regmap_read(ns->regmap, NIOS_FW_VERSION, &val);
> +	if (ret)
> +		return ret;
> +
> +	if (FIELD_GET(NIOS_FW_VERSION_MAJOR, val) < 3)
> +		return sprintf(buf, "not supported\n");
> +
> +	/* If no 25G links, FEC mode setting is not supported either */
> +	ret = get_retimer_mode(ns, PKVL_A_MODE_STS, &retimer_a_mode);
> +	if (ret)
> +		return ret;
> +
> +	ret = get_retimer_mode(ns, PKVL_B_MODE_STS, &retimer_b_mode);
> +	if (ret)
> +		return ret;
> +
> +	if (!IS_RETIMER_FEC_SUPPORTED(retimer_a_mode) &&
> +	    !IS_RETIMER_FEC_SUPPORTED(retimer_b_mode))
> +		return sprintf(buf, "not supported\n");
> +
> +	/* get the valid FEC mode for 25G links */
> +	ret = regmap_read(ns->regmap, NIOS_INIT, &val);
> +	if (ret)
> +		return ret;
> +
> +	/*
> +	 * FEC mode should always be the same for all links, as we set them
> +	 * in this way.
> +	 */
> +	fec_mode = FIELD_GET(REQ_FEC_MODE_A0_MSK, val);
> +	if (fec_mode != FIELD_GET(REQ_FEC_MODE_A1_MSK, val) ||
> +	    fec_mode != FIELD_GET(REQ_FEC_MODE_A2_MSK, val) ||
> +	    fec_mode != FIELD_GET(REQ_FEC_MODE_A3_MSK, val) ||
> +	    fec_mode != FIELD_GET(REQ_FEC_MODE_B0_MSK, val) ||
> +	    fec_mode != FIELD_GET(REQ_FEC_MODE_B1_MSK, val) ||
> +	    fec_mode != FIELD_GET(REQ_FEC_MODE_B2_MSK, val) ||
> +	    fec_mode != FIELD_GET(REQ_FEC_MODE_B3_MSK, val))
> +		return -EFAULT;
> +
> +	switch (fec_mode) {
> +	case REQ_FEC_MODE_NO:
> +		return sprintf(buf, "no\n");
> +	case REQ_FEC_MODE_KR:
> +		return sprintf(buf, "kr\n");
> +	case REQ_FEC_MODE_RS:
> +		return sprintf(buf, "rs\n");
> +	}
> +
> +	return -EFAULT;
> +}
> +static DEVICE_ATTR_RO(fec_mode);
> +
> +static struct attribute *n3000_nios_attrs[] = {
> +	&dev_attr_nios_fw_version.attr,
> +	&dev_attr_fec_mode.attr,
> +	NULL,
> +};
> +ATTRIBUTE_GROUPS(n3000_nios);
> +
> +static int init_error_detected(struct n3000_nios *ns)
Do you want to make the function either bool, or the return values ints?
> +{
> +	unsigned int val;
> +
> +	if (regmap_read(ns->regmap, PKVL_A_MODE_STS, &val))
> +		return true;
> +
> +	if (!IS_MODE_STATUS_OK(val))
> +		return true;
> +
> +	if (regmap_read(ns->regmap, PKVL_B_MODE_STS, &val))
> +		return true;
> +
> +	if (!IS_MODE_STATUS_OK(val))
> +		return true;
> +
> +	return false;
> +}
> +
> +static void dump_error_stat(struct n3000_nios *ns)
> +{
> +	unsigned int val;
> +
> +	if (regmap_read(ns->regmap, PKVL_A_MODE_STS, &val))
> +		return;
> +
> +	dev_err(ns->dev, "PKVL_A_MODE_STS 0x%x\n", val);
> +
> +	if (regmap_read(ns->regmap, PKVL_B_MODE_STS, &val))
> +		return;
> +
> +	dev_err(ns->dev, "PKVL_B_MODE_STS 0x%x\n", val);
> +}
> +
> +static int n3000_nios_init_done_check(struct n3000_nios *ns)
> +{
> +	struct device *dev = ns->dev;
> +	unsigned int val, mode;
> +	int ret;
> +
> +	/*
> +	 * this SPI is shared by Nios core inside FPGA, Nios will use this SPI
> +	 * master to do some one time initialization after power up, and then
> +	 * release the control to OS. driver needs to poll on INIT_DONE to
> +	 * see when driver could take the control.
> +	 *
> +	 * Please note that after Nios firmware version 3.0.0, INIT_START is
> +	 * introduced, so driver needs to trigger START firstly and then check
> +	 * INIT_DONE.
> +	 */
> +
> +	ret = regmap_read(ns->regmap, NIOS_FW_VERSION, &val);
> +	if (ret)
> +		return ret;
> +
> +	/*
> +	 * If Nios version register is totally uninitialized(== 0x0), then the
> +	 * Nios firmware is missing. So host could take control of SPI master
> +	 * safely, but initialization work for Nios is not done. To restore the
> +	 * card, we need to reprogram a new Nios firmware via the BMC chip on
> +	 * SPI bus. So the driver doesn't error out, it continues to create the
> +	 * spi controller device and spi_board_info for BMC.
> +	 */
> +	if (val == 0) {
> +		dev_err(dev, "Nios version reg = 0x%x, skip INIT_DONE check, but the retimer may be uninitialized\n",
This looks long, any chance you can linebreak this?
> +			val);
> +		return 0;
> +	}
> +
> +	if (FIELD_GET(NIOS_FW_VERSION_MAJOR, val) >= 3) {
> +		/* read NIOS_INIT to check if retimer initialization is done */
> +		ret = regmap_read(ns->regmap, NIOS_INIT, &val);
> +		if (ret)
> +			return ret;
> +
> +		/* check if retimers are initialized already */
> +		if (val & NIOS_INIT_DONE || val & NIOS_INIT_START)
> +			goto nios_init_done;
> +
> +		/* configure FEC mode per module param */
> +		val = NIOS_INIT_START;
> +
> +		/*
> +		 * When the retimer is to be set to 10G mode, there is no FEC
> +		 * mode setting, so the REQ_FEC_MODE field will be ignored by
> +		 * Nios firmware in this case. But we should still fill the FEC
> +		 * mode field cause host could not get the retimer working mode
> +		 * until the Nios init is done.
> +		 */
> +		if (!strcmp(fec_mode, "no"))
> +			mode = REQ_FEC_MODE_NO;
> +		else if (!strcmp(fec_mode, "kr"))
> +			mode = REQ_FEC_MODE_KR;
> +		else if (!strcmp(fec_mode, "rs"))
> +			mode = REQ_FEC_MODE_RS;
> +		else
> +			return -EINVAL;
> +
> +		/* set the same FEC mode for all links */
> +		val |= FIELD_PREP(REQ_FEC_MODE_A0_MSK, mode) |
> +		       FIELD_PREP(REQ_FEC_MODE_A1_MSK, mode) |
> +		       FIELD_PREP(REQ_FEC_MODE_A2_MSK, mode) |
> +		       FIELD_PREP(REQ_FEC_MODE_A3_MSK, mode) |
> +		       FIELD_PREP(REQ_FEC_MODE_B0_MSK, mode) |
> +		       FIELD_PREP(REQ_FEC_MODE_B1_MSK, mode) |
> +		       FIELD_PREP(REQ_FEC_MODE_B2_MSK, mode) |
> +		       FIELD_PREP(REQ_FEC_MODE_B3_MSK, mode);
> +
> +		ret = regmap_write(ns->regmap, NIOS_INIT, val);
> +		if (ret)
> +			return ret;
> +	}
> +
> +nios_init_done:
> +	/* polls on NIOS_INIT_DONE */
> +	ret = regmap_read_poll_timeout(ns->regmap, NIOS_INIT, val,
> +				       val & NIOS_INIT_DONE,
> +				       NIOS_INIT_TIME_INTV,
> +				       NIOS_INIT_TIMEOUT);
> +	if (ret) {
> +		dev_err(dev, "NIOS_INIT_DONE %s\n",
> +			(ret == -ETIMEDOUT) ? "timed out" : "check error");
> +		goto dump_sts;
> +	}
> +
> +	/*
> +	 * After INIT_DONE is detected, it still needs to check if any error
> +	 * detected.
> +	 */
> +	if (init_error_detected(ns)) {
> +		/*
> +		 * If the retimer configuration is failed, the Nios firmware
> +		 * will still release the spi controller for host to
> +		 * communicate with the BMC. It makes possible for people to
> +		 * reprogram a new Nios firmware and restore the card. So the
> +		 * driver doesn't error out, it continues to create the spi
> +		 * controller device and spi_board_info for BMC.
> +		 */
> +		dev_err(dev, "NIOS_INIT_DONE OK, but err found during init\n");
> +		goto dump_sts;
> +	}
> +	return 0;
> +
> +dump_sts:
> +	dump_error_stat(ns);
> +
> +	return ret;
> +}
> +
> +struct spi_board_info m10_n3000_info = {
> +	.modalias = "m10-n3000",
Did I miss the patch for this, or did this only go to the SPI folks?
> +	.max_speed_hz = 12500000,
> +	.bus_num = 0,
> +	.chip_select = 0,
> +};

> +
> +static int create_altera_spi_controller(struct n3000_nios *ns)
> +{
> +	struct altera_spi_platform_data pdata = { 0 };
> +	struct platform_device_info pdevinfo = { 0 };
> +	void __iomem *base = ns->base;
> +	u64 v;
> +
> +	v = readq(base + NIOS_SPI_PARAM);
> +
> +	pdata.mode_bits = SPI_CS_HIGH;
> +	if (FIELD_GET(PARAM_CLK_POL, v))
> +		pdata.mode_bits |= SPI_CPOL;
> +	if (FIELD_GET(PARAM_CLK_PHASE, v))
> +		pdata.mode_bits |= SPI_CPHA;
> +
> +	pdata.num_chipselect = FIELD_GET(PARAM_NUM_CS, v);
> +	pdata.bits_per_word_mask =
> +		SPI_BPW_RANGE_MASK(1, FIELD_GET(PARAM_DATA_WIDTH, v));
> +
> +	pdata.num_devices = 1;
> +	pdata.devices = &m10_n3000_info;
> +
> +	dev_dbg(ns->dev, "%s cs %u bpm 0x%x mode 0x%x\n", __func__,
> +		pdata.num_chipselect, pdata.bits_per_word_mask,
> +		pdata.mode_bits);
> +
> +	pdevinfo.name = "subdev_spi_altera";
> +	pdevinfo.id = PLATFORM_DEVID_AUTO;
> +	pdevinfo.parent = ns->dev;
> +	pdevinfo.data = &pdata;
> +	pdevinfo.size_data = sizeof(pdata);
> +
> +	ns->altera_spi = platform_device_register_full(&pdevinfo);
> +	return PTR_ERR_OR_ZERO(ns->altera_spi);
> +}
> +
> +static void destroy_altera_spi_controller(struct n3000_nios *ns)
> +{
> +	platform_device_unregister(ns->altera_spi);
> +}
> +
> +/* ns is the abbreviation of nios_spi */
> +static int ns_poll_stat_timeout(void __iomem *base, u64 *v)
> +{
> +	int loops = NS_REGBUS_WAIT_TIMEOUT;
> +
> +	/*
> +	 * We don't use the time based timeout here for performance.
> +	 *
> +	 * The regbus read/write is on the critical path of Intel PAC N3000
> +	 * image programing. The time based timeout checking will add too much
> +	 * overhead on it. Usually the state changes in 1 or 2 loops on the
> +	 * test server, and we set 10000 times loop here for safety.
> +	 */
> +	do {
> +		*v = readq(base + NIOS_SPI_STAT);
> +		if (*v & STAT_RW_VAL)
> +			break;
> +		cpu_relax();
> +	} while (--loops);
> +
> +	return loops ? 0 : -ETIMEDOUT;
> +}
> +
> +static int ns_reg_write(void *context, unsigned int reg, unsigned int val)
> +{
> +	struct n3000_nios *ns = context;
> +	u64 v = 0;
> +	int ret;
> +
> +	v |= FIELD_PREP(CTRL_CMD_MSK, CTRL_CMD_WR);
> +	v |= FIELD_PREP(CTRL_ADDR, reg);
> +	v |= FIELD_PREP(CTRL_WR_DATA, val);
> +	writeq(v, ns->base + NIOS_SPI_CTRL);
> +
> +	ret = ns_poll_stat_timeout(ns->base, &v);
> +	if (ret)
> +		dev_err(ns->dev, "fail to write reg 0x%x val 0x%x: %d\n",
> +			reg, val, ret);
> +
> +	return ret;
> +}
> +
> +static int ns_reg_read(void *context, unsigned int reg, unsigned int *val)
> +{
> +	struct n3000_nios *ns = context;
> +	u64 v = 0;
> +	int ret;
> +
> +	v |= FIELD_PREP(CTRL_CMD_MSK, CTRL_CMD_RD);
> +	v |= FIELD_PREP(CTRL_ADDR, reg);
> +	writeq(v, ns->base + NIOS_SPI_CTRL);
> +
> +	ret = ns_poll_stat_timeout(ns->base, &v);
> +	if (ret)
> +		dev_err(ns->dev, "fail to read reg 0x%x: %d\n", reg, ret);
> +	else
> +		*val = FIELD_GET(STAT_RD_DATA, v);
> +
> +	return ret;
> +}
> +
> +static const struct regmap_config ns_regbus_cfg = {
> +	.reg_bits = 32,
> +	.reg_stride = 4,
> +	.val_bits = 32,
> +	.fast_io = true,
> +
> +	.reg_write = ns_reg_write,
> +	.reg_read = ns_reg_read,
> +};
> +
> +static int n3000_nios_probe(struct dfl_device *dfl_dev)
> +{
> +	struct device *dev = &dfl_dev->dev;
> +	struct n3000_nios *ns;
> +	int ret;
> +
> +	ns = devm_kzalloc(dev, sizeof(*ns), GFP_KERNEL);
> +	if (!ns)
> +		return -ENOMEM;
> +
> +	dev_set_drvdata(&dfl_dev->dev, ns);
> +
> +	ns->dev = dev;
> +
> +	ns->base = devm_ioremap_resource(&dfl_dev->dev, &dfl_dev->mmio_res);
> +	if (IS_ERR(ns->base))
> +		return PTR_ERR(ns->base);
> +
> +	ns->regmap = devm_regmap_init(dev, NULL, ns, &ns_regbus_cfg);
> +	if (IS_ERR(ns->regmap))
> +		return PTR_ERR(ns->regmap);
> +
> +	ret = n3000_nios_init_done_check(ns);
> +	if (ret)
> +		return ret;
> +
> +	ret = create_altera_spi_controller(ns);
> +	if (ret)
> +		dev_err(dev, "altera spi controller create failed: %d\n", ret);
> +
> +	return ret;
> +}
> +
> +static void n3000_nios_remove(struct dfl_device *dfl_dev)
> +{
> +	struct n3000_nios *ns = dev_get_drvdata(&dfl_dev->dev);
> +
> +	destroy_altera_spi_controller(ns);
> +}
> +
> +#define FME_FEATURE_ID_N3000_NIOS	0xd
> +
> +static const struct dfl_device_id n3000_nios_ids[] = {
> +	{ FME_ID, FME_FEATURE_ID_N3000_NIOS },
> +	{ }
> +};
> +
> +static struct dfl_driver n3000_nios_driver = {
> +	.drv	= {
> +		.name       = "n3000-nios",
> +		.dev_groups = n3000_nios_groups,
> +	},
> +	.id_table = n3000_nios_ids,
> +	.probe   = n3000_nios_probe,
> +	.remove  = n3000_nios_remove,
> +};
> +
> +module_dfl_driver(n3000_nios_driver);
> +
> +MODULE_DEVICE_TABLE(dfl, n3000_nios_ids);
> +MODULE_DESCRIPTION("Driver for Nios private feature on Intel PAC N3000");
> +MODULE_AUTHOR("Intel Corporation");
> +MODULE_LICENSE("GPL v2");
> -- 
> 2.7.4
> 
Thanks,
Moritz

Powered by blists - more mailing lists