| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <9f7c3e8b-872a-e53a-d144-4c558fa6c0b6@linaro.org>
Date: Wed, 16 Sep 2020 13:54:52 +0100
From: Srinivas Kandagatla <srinivas.kandagatla@...aro.org>
To: Vinod Koul <vkoul@...nel.org>
Cc: yung-chuan.liao@...ux.intel.com,
pierre-louis.bossart@...ux.intel.com, sanyog.r.kale@...el.com,
alsa-devel@...a-project.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH v2 3/3] soundwire: qcom: get max rows and cols info from
compatible
On 16/09/2020 13:49, Vinod Koul wrote:
> On 16-09-20, 10:21, Srinivas Kandagatla wrote:
>> currently the max rows and cols values are hardcoded. In reality
>> these values depend on the IP version. So get these based on
>> device tree compatible strings.
>>
>> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@...aro.org>
>> ---
>> drivers/soundwire/qcom.c | 50 ++++++++++++++++++++++++++++------------
>> 1 file changed, 35 insertions(+), 15 deletions(-)
>>
>> diff --git a/drivers/soundwire/qcom.c b/drivers/soundwire/qcom.c
>> index 76963a7bdaa3..1dbf33684470 100644
>> --- a/drivers/soundwire/qcom.c
>> +++ b/drivers/soundwire/qcom.c
>> @@ -66,11 +66,6 @@
>> #define SWRM_REG_VAL_PACK(data, dev, id, reg) \
>> ((reg) | ((id) << 16) | ((dev) << 20) | ((data) << 24))
>>
>> -#define SWRM_MAX_ROW_VAL 0 /* Rows = 48 */
>> -#define SWRM_DEFAULT_ROWS 48
>> -#define SWRM_MIN_COL_VAL 0 /* Cols = 2 */
>> -#define SWRM_DEFAULT_COL 16
>> -#define SWRM_MAX_COL_VAL 7
>> #define SWRM_SPECIAL_CMD_ID 0xF
>> #define MAX_FREQ_NUM 1
>> #define TIMEOUT_MS (2 * HZ)
>> @@ -104,6 +99,8 @@ struct qcom_swrm_ctrl {
>> unsigned int version;
>> int num_din_ports;
>> int num_dout_ports;
>> + int cols_index;
>> + int rows_index;
>> unsigned long dout_port_mask;
>> unsigned long din_port_mask;
>> struct qcom_swrm_port_config pconfig[QCOM_SDW_MAX_PORTS];
>> @@ -113,6 +110,21 @@ struct qcom_swrm_ctrl {
>> int (*reg_write)(struct qcom_swrm_ctrl *ctrl, int reg, int val);
>> };
>>
>> +struct qcom_swrm_data {
>> + u32 default_cols;
>> + u32 default_rows;
>> +};
>> +
>> +static struct qcom_swrm_data swrm_v1_3_data = {
>> + .default_rows = 48,
>> + .default_cols = 16,
>> +};
>> +
>> +static struct qcom_swrm_data swrm_v1_5_data = {
>> + .default_rows = 50,
>> + .default_cols = 16,
>> +};
>> +
>> #define to_qcom_sdw(b) container_of(b, struct qcom_swrm_ctrl, bus)
>>
>> static int qcom_swrm_ahb_reg_read(struct qcom_swrm_ctrl *ctrl, int reg,
>> @@ -299,8 +311,10 @@ static int qcom_swrm_init(struct qcom_swrm_ctrl *ctrl)
>> u32 val;
>>
>> /* Clear Rows and Cols */
>> - val = FIELD_PREP(SWRM_MCP_FRAME_CTRL_BANK_ROW_CTRL_BMSK, SWRM_MAX_ROW_VAL);
>> - val |= FIELD_PREP(SWRM_MCP_FRAME_CTRL_BANK_COL_CTRL_BMSK, SWRM_MIN_COL_VAL);
>> + val = FIELD_PREP(SWRM_MCP_FRAME_CTRL_BANK_ROW_CTRL_BMSK,
>> + ctrl->rows_index);
>> + val |= FIELD_PREP(SWRM_MCP_FRAME_CTRL_BANK_COL_CTRL_BMSK,
>> + ctrl->cols_index);
>
> single line for these ?
My vimrc had this 80 line autowrap thingy which might have done this!!
>
>> ctrl->reg_write(ctrl, SWRM_MCP_FRAME_CTRL_BANK_ADDR(0), val);
>>
>> @@ -378,8 +392,10 @@ static int qcom_swrm_pre_bank_switch(struct sdw_bus *bus)
>> val &= ~SWRM_MCP_FRAME_CTRL_BANK_COL_CTRL_BMSK;
>> val &= ~SWRM_MCP_FRAME_CTRL_BANK_ROW_CTRL_BMSK;
>>
>> - val |= FIELD_PREP(SWRM_MCP_FRAME_CTRL_BANK_COL_CTRL_BMSK, SWRM_MAX_COL_VAL);
>> - val |= FIELD_PREP(SWRM_MCP_FRAME_CTRL_BANK_ROW_CTRL_BMSK, SWRM_MAX_ROW_VAL);
>> + val |= FIELD_PREP(SWRM_MCP_FRAME_CTRL_BANK_COL_CTRL_BMSK,
>> + ctrl->cols_index);
>> + val |= FIELD_PREP(SWRM_MCP_FRAME_CTRL_BANK_ROW_CTRL_BMSK,
>> + ctrl->rows_index);
>
> here as well
>
>>
>> return ctrl->reg_write(ctrl, reg, val);
>> }
>> @@ -780,6 +796,7 @@ static int qcom_swrm_probe(struct platform_device *pdev)
>> struct sdw_master_prop *prop;
>> struct sdw_bus_params *params;
>> struct qcom_swrm_ctrl *ctrl;
>> + const struct qcom_swrm_data *data;
>> int ret;
>> u32 val;
>>
>> @@ -787,6 +804,9 @@ static int qcom_swrm_probe(struct platform_device *pdev)
>> if (!ctrl)
>> return -ENOMEM;
>>
>> + data = of_device_get_match_data(dev);
>
> Wont it be good to check if data is valid, we do dereference it few line
> below
We Should not hit that case as we will never reach here without matching
compatible!
If you insist, I can add a check but data will be always be valid at the
time of check!
>
>> + ctrl->rows_index = sdw_find_row_index(data->default_rows);
>> + ctrl->cols_index = sdw_find_col_index(data->default_cols);
>> #if IS_ENABLED(CONFIG_SLIMBUS)
>> if (dev->parent->bus == &slimbus_bus) {
>> #else
>> @@ -836,8 +856,8 @@ static int qcom_swrm_probe(struct platform_device *pdev)
>> params = &ctrl->bus.params;
>> params->max_dr_freq = DEFAULT_CLK_FREQ;
>> params->curr_dr_freq = DEFAULT_CLK_FREQ;
>> - params->col = SWRM_DEFAULT_COL;
>> - params->row = SWRM_DEFAULT_ROWS;
>> + params->col = data->default_cols;
>> + params->row = data->default_rows;
>> ctrl->reg_read(ctrl, SWRM_MCP_STATUS, &val);
>> params->curr_bank = val & SWRM_MCP_STATUS_BANK_NUM_MASK;
>> params->next_bank = !params->curr_bank;
>> @@ -847,8 +867,8 @@ static int qcom_swrm_probe(struct platform_device *pdev)
>> prop->num_clk_gears = 0;
>> prop->num_clk_freq = MAX_FREQ_NUM;
>> prop->clk_freq = &qcom_swrm_freq_tbl[0];
>> - prop->default_col = SWRM_DEFAULT_COL;
>> - prop->default_row = SWRM_DEFAULT_ROWS;
>> + prop->default_col = data->default_cols;
>> + prop->default_row = data->default_rows;
>>
>> ctrl->reg_read(ctrl, SWRM_COMP_HW_VERSION, &ctrl->version);
>>
>> @@ -899,8 +919,8 @@ static int qcom_swrm_remove(struct platform_device *pdev)
>> }
>>
>> static const struct of_device_id qcom_swrm_of_match[] = {
>> - { .compatible = "qcom,soundwire-v1.3.0", },
>> - { .compatible = "qcom,soundwire-v1.5.1", },
>> + { .compatible = "qcom,soundwire-v1.3.0", .data = &swrm_v1_3_data },
>> + { .compatible = "qcom,soundwire-v1.5.1", .data = &swrm_v1_5_data },
>> {/* sentinel */},
>> };
>>
>> --
>> 2.21.0
>
Powered by blists - more mailing lists