| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Tue, 22 Sep 2020 14:38:53 -0700
From: Sean V Kelley <seanvk.dev@...gontracks.org>
To: bhelgaas@...gle.com, Jonathan.Cameron@...wei.com,
rafael.j.wysocki@...el.com, ashok.raj@...el.com,
tony.luck@...el.com, sathyanarayanan.kuppuswamy@...el.com,
qiuxu.zhuo@...el.com
Cc: linux-pci@...r.kernel.org, linux-kernel@...r.kernel.org,
Sean V Kelley <sean.v.kelley@...el.com>
Subject: [PATCH v6 04/10] PCI/AER: Extend AER error handling to RCECs
From: Jonathan Cameron <Jonathan.Cameron@...wei.com>
Currently the kernel does not handle AER errors for Root Complex
integrated End Points (RCiEPs)[0]. These devices sit on a root bus within
the Root Complex (RC). AER handling is performed by a Root Complex Event
Collector (RCEC) [1] which is a effectively a type of RCiEP on the same
root bus.
For an RCEC (technically not a Bridge), error messages "received" from
associated RCiEPs must be enabled for "transmission" in order to cause a
System Error via the Root Control register or (when the Advanced Error
Reporting Capability is present) reporting via the Root Error Command
register and logging in the Root Error Status register and Error Source
Identification register.
In addition to the defined OS level handling of the reset flow for the
associated RCiEPs of an RCEC, it is possible to also have non-native
handling. In that case there is no need to take any actions on the RCEC
because the firmware is responsible for them. This is true where APEI [2]
is used to report the AER errors via a GHES[v2] HEST entry [3] and
relevant AER CPER record [4] and non-native handling is in use.
We effectively end up with two different types of discovery for
purposes of handling AER errors:
1) Normal bus walk - we pass the downstream port above a bus to which
the device is attached and it walks everything below that point.
2) An RCiEP with no visible association with an RCEC as there is no need
to walk devices. In that case, the flow is to just call the callbacks for
the actual device, which in turn references its associated RCEC.
A new walk function pci_bridge_walk(), similar to pci_bus_walk(),
is provided that takes a pci_dev instead of a bus. If that bridge
corresponds to a downstream port it will walk the subordinate bus of
that bridge. If the device does not then it will call the function on
that device alone.
[0] ACPI PCI Express Base Specification 5.0-1 1.3.2.3 Root Complex
Integrated Endpoint Rules.
[1] ACPI PCI Express Base Specification 5.0-1 6.2 Error Signalling and
Logging
[2] ACPI Specification 6.3 Chapter 18 ACPI Platform Error Interface (APEI)
[3] ACPI Specification 6.3 18.2.3.7 Generic Hardware Error Source
[4] UEFI Specification 2.8, N.2.7 PCI Express Error Section
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@...wei.com>
Signed-off-by: Sean V Kelley <sean.v.kelley@...el.com>
---
drivers/pci/pci.h | 2 +-
drivers/pci/pcie/err.c | 77 +++++++++++++++++++++++++++++++-----------
2 files changed, 59 insertions(+), 20 deletions(-)
diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
index 83670a6425d8..7b547fc3679a 100644
--- a/drivers/pci/pci.h
+++ b/drivers/pci/pci.h
@@ -575,7 +575,7 @@ static inline int pci_dev_specific_disable_acs_redir(struct pci_dev *dev)
/* PCI error reporting and recovery */
pci_ers_result_t pcie_do_recovery(struct pci_dev *dev,
pci_channel_state_t state,
- pci_ers_result_t (*reset_link)(struct pci_dev *pdev));
+ pci_ers_result_t (*reset_subordinate_devices)(struct pci_dev *pdev));
bool pcie_wait_for_link(struct pci_dev *pdev, bool active);
#ifdef CONFIG_PCIEASPM
diff --git a/drivers/pci/pcie/err.c b/drivers/pci/pcie/err.c
index c543f419d8f9..e575fa6cee63 100644
--- a/drivers/pci/pcie/err.c
+++ b/drivers/pci/pcie/err.c
@@ -146,38 +146,73 @@ static int report_resume(struct pci_dev *dev, void *data)
return 0;
}
+/**
+ * pci_bridge_walk - walk bridges potentially AER affected
+ * @bridge bridge which may be an RCEC with associated RCiEPs,
+ * an RCiEP associated with an RCEC, or a Port.
+ * @cb callback to be called for each device found
+ * @userdata arbitrary pointer to be passed to callback.
+ *
+ * If the device provided is a bridge, walk the subordinate bus,
+ * including any bridged devices on buses under this bus.
+ * Call the provided callback on each device found.
+ *
+ * If the device provided has no subordinate bus, call the provided
+ * callback on the device itself.
+ */
+static void pci_bridge_walk(struct pci_dev *bridge, int (*cb)(struct pci_dev *, void *),
+ void *userdata)
+{
+ if (bridge->subordinate)
+ pci_walk_bus(bridge->subordinate, cb, userdata);
+ else
+ cb(bridge, userdata);
+}
+
pci_ers_result_t pcie_do_recovery(struct pci_dev *dev,
pci_channel_state_t state,
- pci_ers_result_t (*reset_link)(struct pci_dev *pdev))
+ pci_ers_result_t (*reset_subordinate_devices)(struct pci_dev *pdev))
{
pci_ers_result_t status = PCI_ERS_RESULT_CAN_RECOVER;
- struct pci_bus *bus;
+ struct pci_dev *bridge;
+ int type;
/*
- * Error recovery runs on all subordinates of the first downstream port.
- * If the downstream port detected the error, it is cleared at the end.
+ * Error recovery runs on all subordinates of the first downstream
+ * bridge. If the downstream bridge detected the error, it is
+ * cleared at the end. For RCiEPs we should reset just the RCiEP itself.
*/
- if (!(pci_pcie_type(dev) == PCI_EXP_TYPE_ROOT_PORT ||
- pci_pcie_type(dev) == PCI_EXP_TYPE_DOWNSTREAM))
- dev = dev->bus->self;
- bus = dev->subordinate;
+ type = pci_pcie_type(dev);
+ if (type == PCI_EXP_TYPE_ROOT_PORT ||
+ type == PCI_EXP_TYPE_DOWNSTREAM ||
+ type == PCI_EXP_TYPE_RC_EC ||
+ type == PCI_EXP_TYPE_RC_END)
+ bridge = dev;
+ else
+ bridge = pci_upstream_bridge(dev);
pci_dbg(dev, "broadcast error_detected message\n");
if (state == pci_channel_io_frozen) {
- pci_walk_bus(bus, report_frozen_detected, &status);
- status = reset_link(dev);
+ pci_bridge_walk(bridge, report_frozen_detected, &status);
+ if (type == PCI_EXP_TYPE_RC_END) {
+ pci_warn(dev, "link reset not possible for RCiEP\n");
+ status = PCI_ERS_RESULT_NONE;
+ goto failed;
+ }
+
+ status = reset_subordinate_devices(bridge);
if (status != PCI_ERS_RESULT_RECOVERED) {
- pci_warn(dev, "link reset failed\n");
+ pci_warn(dev, "subordinate device reset failed\n");
goto failed;
}
} else {
- pci_walk_bus(bus, report_normal_detected, &status);
+ pci_bridge_walk(bridge, report_normal_detected, &status);
}
if (status == PCI_ERS_RESULT_CAN_RECOVER) {
status = PCI_ERS_RESULT_RECOVERED;
pci_dbg(dev, "broadcast mmio_enabled message\n");
- pci_walk_bus(bus, report_mmio_enabled, &status);
+ pci_bridge_walk(bridge, report_mmio_enabled, &status);
}
if (status == PCI_ERS_RESULT_NEED_RESET) {
@@ -188,18 +223,22 @@ pci_ers_result_t pcie_do_recovery(struct pci_dev *dev,
*/
status = PCI_ERS_RESULT_RECOVERED;
pci_dbg(dev, "broadcast slot_reset message\n");
- pci_walk_bus(bus, report_slot_reset, &status);
+ pci_bridge_walk(bridge, report_slot_reset, &status);
}
if (status != PCI_ERS_RESULT_RECOVERED)
goto failed;
pci_dbg(dev, "broadcast resume message\n");
- pci_walk_bus(bus, report_resume, &status);
-
- if (pcie_aer_is_native(dev))
- pcie_clear_device_status(dev);
- pci_aer_clear_nonfatal_status(dev);
+ pci_bridge_walk(bridge, report_resume, &status);
+
+ if (type == PCI_EXP_TYPE_ROOT_PORT ||
+ type == PCI_EXP_TYPE_DOWNSTREAM ||
+ type == PCI_EXP_TYPE_RC_EC) {
+ if (pcie_aer_is_native(bridge))
+ pcie_clear_device_status(bridge);
+ pci_aer_clear_nonfatal_status(bridge);
+ }
pci_info(dev, "device recovery successful\n");
return status;
--
2.28.0
Powered by blists - more mailing lists