| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <DM6PR07MB5529378995C9D9EAC83070F0DD330@DM6PR07MB5529.namprd07.prod.outlook.com>
Date: Wed, 30 Sep 2020 11:58:07 +0000
From: Pawel Laszczak <pawell@...ence.com>
To: Chunfeng Yun <chunfeng.yun@...iatek.com>
CC: "gregkh@...uxfoundation.org" <gregkh@...uxfoundation.org>,
"linux-usb@...r.kernel.org" <linux-usb@...r.kernel.org>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
"balbi@...nel.org" <balbi@...nel.org>,
"colin.king@...onical.com" <colin.king@...onical.com>,
"rogerq@...com" <rogerq@...com>,
"peter.chen@....com" <peter.chen@....com>,
Jayshri Dajiram Pawar <jpawar@...ence.com>,
Rahul Kumar <kurahul@...ence.com>,
Sanket Parmar <sparmar@...ence.com>,
"nsekhar@...com" <nsekhar@...com>,
"heikki.krogerus@...ux.intel.com" <heikki.krogerus@...ux.intel.com>,
"yanaijie@...wei.com" <yanaijie@...wei.com>
Subject: RE: [PATCH 7/8] usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD
Driver
>
>On Mon, 2020-09-28 at 14:27 +0200, Pawel Laszczak wrote:
>> This patch introduces the main part of Cadence USBSSP DRD driver
>> to Linux kernel.
>> To reduce the patch size a little bit, the header file gadget.h was
>> intentionally added as separate patch.
>>
>> The Cadence USBSSP DRD Controller is a highly configurable IP Core which
>> can be instantiated as Dual-Role Device (DRD), Peripheral Only and
>> Host Only (XHCI)configurations.
>>
>> The current driver has been validated with FPGA platform. We have
>> support for PCIe bus, which is used on FPGA prototyping.
>>
>> The host side of USBSS DRD controller is compliant with XHCI.
>> The architecture for device side is almost the same as for host side,
>> and most of the XHCI specification can be used to understand how
>> this controller operates.
>>
>> Signed-off-by: Pawel Laszczak <pawell@...ence.com>
>> ---
>> drivers/usb/Kconfig | 1 +
>> drivers/usb/Makefile | 1 +
>> drivers/usb/cdns3/core.c | 19 +-
>> drivers/usb/cdns3/drd.c | 28 +
>> drivers/usb/cdns3/drd.h | 2 +
>> drivers/usb/cdns3/gadget-export.h | 18 +-
>> drivers/usb/cdns3/host-export.h | 4 +-
>> drivers/usb/cdnsp/Kconfig | 40 +
>> drivers/usb/cdnsp/Makefile | 7 +
>> drivers/usb/cdnsp/cdnsp-pci.c | 247 +++
>> drivers/usb/cdnsp/ep0.c | 480 ++++++
>> drivers/usb/cdnsp/gadget.c | 1946 ++++++++++++++++++++++++
>> drivers/usb/cdnsp/gadget.h | 139 ++
>> drivers/usb/cdnsp/mem.c | 1312 ++++++++++++++++
>> drivers/usb/cdnsp/ring.c | 2363 +++++++++++++++++++++++++++++
>> 15 files changed, 6600 insertions(+), 7 deletions(-)
>> create mode 100644 drivers/usb/cdnsp/Kconfig
>> create mode 100644 drivers/usb/cdnsp/Makefile
>> create mode 100644 drivers/usb/cdnsp/cdnsp-pci.c
>> create mode 100644 drivers/usb/cdnsp/ep0.c
>> create mode 100644 drivers/usb/cdnsp/gadget.c
>> create mode 100644 drivers/usb/cdnsp/mem.c
>> create mode 100644 drivers/usb/cdnsp/ring.c
>>
>> diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
>> index 26475b409b53..555c4a4cb465 100644
>> --- a/drivers/usb/Kconfig
>> +++ b/drivers/usb/Kconfig
>> @@ -112,6 +112,7 @@ source "drivers/usb/usbip/Kconfig"
>> endif
>>
>> source "drivers/usb/cdns3/Kconfig"
>> +source "drivers/usb/cdnsp/Kconfig"
>>
>> source "drivers/usb/mtu3/Kconfig"
>>
>> diff --git a/drivers/usb/Makefile b/drivers/usb/Makefile
>> index 1c1c1d659394..84727f7a4b92 100644
>> --- a/drivers/usb/Makefile
>> +++ b/drivers/usb/Makefile
>> @@ -14,6 +14,7 @@ obj-$(CONFIG_USB_DWC2) += dwc2/
>> obj-$(CONFIG_USB_ISP1760) += isp1760/
>>
>> obj-$(CONFIG_USB_CDNS3) += cdns3/
>> +obj-$(CONFIG_USB_CDNSP) += cdnsp/
>>
>> obj-$(CONFIG_USB_MON) += mon/
>> obj-$(CONFIG_USB_MTU3) += mtu3/
>> diff --git a/drivers/usb/cdns3/core.c b/drivers/usb/cdns3/core.c
>> index 2af99294beaa..560783092d8a 100644
>> --- a/drivers/usb/cdns3/core.c
>> +++ b/drivers/usb/cdns3/core.c
>> @@ -138,7 +138,14 @@ static int cdns_core_init_role(struct cdns *cdns)
>> dr_mode = best_dr_mode;
>>
>> if (dr_mode == USB_DR_MODE_OTG || dr_mode == USB_DR_MODE_HOST) {
>> - ret = cdns_host_init(cdns);
>> + if ((cdns->version == CDNSP_CONTROLLER_V2 &&
>> + IS_ENABLED(CONFIG_USB_CDNSP_HOST)) ||
>> + (cdns->version < CDNSP_CONTROLLER_V2 &&
>> + IS_ENABLED(CONFIG_USB_CDNS3_HOST)))
>> + ret = cdns_host_init(cdns);
>> + else
>> + ret = -ENXIO;
>> +
>> if (ret) {
>> dev_err(dev, "Host initialization failed with %d\n",
>> ret);
>> @@ -147,7 +154,15 @@ static int cdns_core_init_role(struct cdns *cdns)
>> }
>>
>> if (dr_mode == USB_DR_MODE_OTG || dr_mode == USB_DR_MODE_PERIPHERAL) {
>> - ret = cdns3_gadget_init(cdns);
>> + if (cdns->version == CDNSP_CONTROLLER_V2 &&
>> + IS_ENABLED(CONFIG_USB_CDNSP_GADGET))
>> + ret = cdnsp_gadget_init(cdns);
>> + else if (cdns->version < CDNSP_CONTROLLER_V2 &&
>> + IS_ENABLED(CONFIG_USB_CDNS3_GADGET))
>> + ret = cdns3_gadget_init(cdns);
>> + else
>> + ret = -ENXIO;
>> +
>> if (ret) {
>> dev_err(dev, "Device initialization failed with %d\n",
>> ret);
>> diff --git a/drivers/usb/cdns3/drd.c b/drivers/usb/cdns3/drd.c
>> index 7feb622972da..3c732e19c61c 100644
>> --- a/drivers/usb/cdns3/drd.c
>> +++ b/drivers/usb/cdns3/drd.c
>> @@ -90,6 +90,32 @@ int cdns_get_vbus(struct cdns *cdns)
>> return vbus;
>> }
>>
>> +void cdns_clear_vbus(struct cdns *cdns)
>> +{
>> + u32 reg;
>> +
>> + if (cdns->version != CDNSP_CONTROLLER_V2)
>> + return;
>> +
>> + reg = readl(&cdns->otg_cdnsp_regs->override);
>> + reg |= OVERRIDE_SESS_VLD_SEL;
>> + writel(reg, &cdns->otg_cdnsp_regs->override);
>> +}
>> +EXPORT_SYMBOL_GPL(cdns_clear_vbus);
>> +
>> +void cdns_set_vbus(struct cdns *cdns)
>> +{
>> + u32 reg;
>> +
>> + if (cdns->version != CDNSP_CONTROLLER_V2)
>> + return;
>> +
>> + reg = readl(&cdns->otg_cdnsp_regs->override);
>> + reg &= ~OVERRIDE_SESS_VLD_SEL;
>> + writel(reg, &cdns->otg_cdnsp_regs->override);
>Is this use to force vbus-valid signal always valid? if it is,
>is there any issue if work as device only mode?
It only returns the control of vbus signal back to hardware.
cdns_clear/set_vbus are used only in cdnsp_gadget_pullup function for "software"
connect/disconnect. It cause that "software" connect/disconnect is
more like physical connect/disconnect.
I haven't seen any issue with this.
>
>> +}
>> +EXPORT_SYMBOL_GPL(cdns_set_vbus);
>> +
>> bool cdns_is_host(struct cdns *cdns)
>> {
>> if (cdns->dr_mode == USB_DR_MODE_HOST)
>> @@ -431,5 +457,7 @@ int cdns_drd_init(struct cdns *cdns)
>> int cdns_drd_exit(struct cdns *cdns)
>> {
>> cdns_otg_disable_irq(cdns);
>> + devm_free_irq(cdns->dev, cdns->otg_irq, cdns);
>> +
>> return 0;
>> }
>> diff --git a/drivers/usb/cdns3/drd.h b/drivers/usb/cdns3/drd.h
>> index b92e2834dc3f..7ef14bef047c 100644
>> --- a/drivers/usb/cdns3/drd.h
>> +++ b/drivers/usb/cdns3/drd.h
>> @@ -204,6 +204,8 @@ bool cdns_is_host(struct cdns *cdns);
>> bool cdns_is_device(struct cdns *cdns);
>> int cdns_get_id(struct cdns *cdns);
>> int cdns_get_vbus(struct cdns *cdns);
>> +extern void cdns_clear_vbus(struct cdns *cdns);
>> +extern void cdns_set_vbus(struct cdns *cdns);
>> int cdns_drd_init(struct cdns *cdns);
>> int cdns_drd_exit(struct cdns *cdns);
>> int cdns_drd_update_mode(struct cdns *cdns);
>> diff --git a/drivers/usb/cdns3/gadget-export.h b/drivers/usb/cdns3/gadget-export.h
>> index e784584fe053..b7eec9fb8fda 100644
>> --- a/drivers/usb/cdns3/gadget-export.h
>> +++ b/drivers/usb/cdns3/gadget-export.h
>> @@ -1,6 +1,6 @@
>> /* SPDX-License-Identifier: GPL-2.0 */
>> /*
>> - * Cadence USBSS DRD Driver - Gadget Export APIs.
>> + * Cadence USBSS and USBSSP DRD Driver - Gadget Export APIs.
>> *
>> * Copyright (C) 2017 NXP
>> * Copyright (C) 2017-2018 NXP
>> @@ -10,7 +10,19 @@
>> #ifndef __LINUX_CDNS3_GADGET_EXPORT
>> #define __LINUX_CDNS3_GADGET_EXPORT
>>
>> -#ifdef CONFIG_USB_CDNS3_GADGET
>> +#if IS_ENABLED(CONFIG_USB_CDNSP_GADGET)
>> +
>> +extern int cdnsp_gadget_init(struct cdns *cdns);
>> +#else
>> +
>> +static inline int cdnsp_gadget_init(struct cdns *cdns)
>> +{
>> + return -ENXIO;
>> +}
>> +
>> +#endif /* CONFIG_USB_CDNSP_GADGET */
>> +
>> +#if IS_ENABLED(CONFIG_USB_CDNS3_GADGET)
>>
>> extern int cdns3_gadget_init(struct cdns *cdns);
>> void cdns3_gadget_exit(struct cdns *cdns);
>> @@ -23,6 +35,6 @@ static inline int cdns3_gadget_init(struct cdns *cdns)
>>
>> static inline void cdns3_gadget_exit(struct cdns *cdns) { }
>>
>> -#endif
>> +#endif /* CONFIG_USB_CDNS3_GADGET */
>>
>> #endif /* __LINUX_CDNS3_GADGET_EXPORT */
>> diff --git a/drivers/usb/cdns3/host-export.h b/drivers/usb/cdns3/host-export.h
>> index d82b83d070ad..41f7ea1fed29 100644
>> --- a/drivers/usb/cdns3/host-export.h
>> +++ b/drivers/usb/cdns3/host-export.h
>> @@ -9,7 +9,7 @@
>> #ifndef __LINUX_CDNS3_HOST_EXPORT
>> #define __LINUX_CDNS3_HOST_EXPORT
>>
>> -#ifdef CONFIG_USB_CDNS3_HOST
>> +#if IS_ENABLED(CONFIG_USB_CDNS3_HOST) || IS_ENABLED(CONFIG_USB_CDNSP_GADGET)
>>
>> int cdns_host_init(struct cdns *cdns);
>>
>> @@ -22,6 +22,6 @@ static inline int cdns_host_init(struct cdns *cdns)
>>
>> static inline void cdns_host_exit(struct cdns *cdns) { }
>>
>> -#endif /* CONFIG_USB_CDNS3_HOST */
>> +#endif /* CONFIG_USB_CDNS3_HOST || CONFIG_USB_CDNSP_GADGET */
>>
>> #endif /* __LINUX_CDNS3_HOST_EXPORT */
>> diff --git a/drivers/usb/cdnsp/Kconfig b/drivers/usb/cdnsp/Kconfig
>> new file mode 100644
>> index 000000000000..56cee5f6dfb4
>> --- /dev/null
>> +++ b/drivers/usb/cdnsp/Kconfig
>> @@ -0,0 +1,40 @@
>> +config USB_CDNSP_PCI
>> + tristate "Cadence CDNSP Dual-Role Controller"
>> + depends on USB_SUPPORT && (USB || USB_GADGET) && HAS_DMA && USB_PCI && ACPI
>> + select USB_XHCI_PLATFORM if USB_XHCI_HCD
>> + select USB_ROLE_SWITCH
>> + select CDNS_USB_COMMON
>> + help
>> + Say Y here if your system has a Cadence CDNSP dual-role controller.
>> + It supports: dual-role switch Host-only, and Peripheral-only.
>> +
>> + If you choose to build this driver is a dynamically linked
>> + module, the module will be called cdnsp.ko.
>> +
>> +if USB_CDNSP_PCI
>> +
>> +config USB_CDNSP_GADGET
>> + bool "Cadence CDNSP device controller"
>> + depends on USB_GADGET=y || USB_GADGET=USB_CDNSP_PCI
>> + help
>> + Say Y here to enable device controller functionality of the
>> + Cadence CDNSP-DEV driver.
>> +
>> + Cadence CDNSP Device Controller in device mode is
>> + very similar to XHCI controller. Therefore some algorithms
>> + used has been taken from host driver.
>> + This controller supports FF, HS, SS and SSP mode.
>> + It doesn't support LS.
>> +
>> +config USB_CDNSP_HOST
>> + bool "Cadence CDNSP host controller"
>> + depends on USB=y || USB=USB_CDNSP_PCI
>> + select CDNS_USB_HOST
>> + help
>> + Say Y here to enable host controller functionality of the
>> + Cadence driver.
>> +
>> + Host controller is compliant with XHCI so it uses
>> + standard XHCI driver.
>> +
>> +endif
>> diff --git a/drivers/usb/cdnsp/Makefile b/drivers/usb/cdnsp/Makefile
>> new file mode 100644
>> index 000000000000..53202b21a8d2
>> --- /dev/null
>> +++ b/drivers/usb/cdnsp/Makefile
>> @@ -0,0 +1,7 @@
>> +# SPDX-License-Identifier: GPL-2.0
>> +
>> +cdnsp-udc-pci-y := cdnsp-pci.o
>> +
>> +obj-$(CONFIG_USB_CDNSP_PCI) += cdnsp-udc-pci.o
>> +cdnsp-udc-pci-$(CONFIG_USB_CDNSP_GADGET) += ring.o gadget.o mem.o ep0.o
>> +
>> diff --git a/drivers/usb/cdnsp/cdnsp-pci.c b/drivers/usb/cdnsp/cdnsp-pci.c
>> new file mode 100644
>> index 000000000000..f67ee8effcd3
>> --- /dev/null
>> +++ b/drivers/usb/cdnsp/cdnsp-pci.c
>> @@ -0,0 +1,247 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Cadence PCI Glue driver.
>> + *
>> + * Copyright (C) 2019 Cadence.
>> + *
>> + * Author: Pawel Laszczak <pawell@...ence.com>
>> + *
>> + */
>> +
>> +#include <linux/platform_device.h>
>> +#include <linux/dma-mapping.h>
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/slab.h>
>> +#include <linux/pci.h>
>> +
>> +#include "../cdns3/core.h"
>> +
>> +#define PCI_BAR_HOST 0
>> +#define PCI_BAR_OTG 0
>> +#define PCI_BAR_DEV 2
>> +
>> +#define PCI_DEV_FN_HOST_DEVICE 0
>> +#define PCI_DEV_FN_OTG 1
>> +
>> +#define PCI_DRIVER_NAME "cdns-pci-usbssp"
>> +#define PLAT_DRIVER_NAME "cdns-usbssp"
>> +
>> +#define CDNS_VENDOR_ID 0x17cd
>> +#define CDNS_DEVICE_ID 0x0100
>> +#define CDNS_DRD_IF (PCI_CLASS_SERIAL_USB << 8 | 0x80)
>> +
>> +static struct pci_dev *cdnsp_get_second_fun(struct pci_dev *pdev)
>> +{
>> + struct pci_dev *func;
>> +
>> + /*
>> + * Gets the second function.
>> + * It's little tricky, but this platform has two function.
>> + * The fist keeps resources for Host/Device while the second
>> + * keeps resources for DRD/OTG.
>> + */
>> + func = pci_get_device(pdev->vendor, pdev->device, NULL);
>> + if (!func)
>> + return NULL;
>> +
>> + if (func->devfn == pdev->devfn) {
>> + func = pci_get_device(pdev->vendor, pdev->device, func);
>> + if (!func)
>> + return NULL;
>> + }
>> +
>> + return func;
>> +}
>> +
>> +static int cdnsp_pci_probe(struct pci_dev *pdev,
>> + const struct pci_device_id *id)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct pci_dev *func;
>> + struct resource *res;
>> + struct cdns *cdnsp;
>> + int ret;
>> +
>> + /*
>> + * For GADGET/HOST PCI (devfn) function number is 0,
>> + * for OTG PCI (devfn) function number is 1.
>> + */
>> + if (!id || (pdev->devfn != PCI_DEV_FN_HOST_DEVICE &&
>> + pdev->devfn != PCI_DEV_FN_OTG))
>> + return -EINVAL;
>> +
>> + func = cdnsp_get_second_fun(pdev);
>> + if (!func)
>> + return -EINVAL;
>> +
>> + if (func->class == PCI_CLASS_SERIAL_USB_XHCI ||
>> + pdev->class == PCI_CLASS_SERIAL_USB_XHCI) {
>> + ret = -EINVAL;
>> + goto put_pci;
>> + }
>> +
>> + ret = pcim_enable_device(pdev);
>> + if (ret) {
>> + dev_err(&pdev->dev, "Enabling PCI device has failed %d\n", ret);
>> + goto put_pci;
>> + }
>> +
>> + pci_set_master(pdev);
>> + if (pci_is_enabled(func)) {
>> + cdnsp = pci_get_drvdata(func);
>> + } else {
>> + cdnsp = kzalloc(sizeof(*cdnsp), GFP_KERNEL);
>> + if (!cdnsp) {
>> + ret = -ENOMEM;
>> + goto disable_pci;
>> + }
>> + }
>> +
>> + /* For GADGET device function number is 0. */
>> + if (pdev->devfn == 0) {
>> + resource_size_t rsrc_start, rsrc_len;
>> +
>> + /* Function 0: host(BAR_0) + device(BAR_1).*/
>> + dev_dbg(dev, "Initialize resources\n");
>> + rsrc_start = pci_resource_start(pdev, PCI_BAR_DEV);
>> + rsrc_len = pci_resource_len(pdev, PCI_BAR_DEV);
>> + res = devm_request_mem_region(dev, rsrc_start, rsrc_len, "dev");
>> + if (!res) {
>> + dev_dbg(dev, "controller already in use\n");
>> + ret = -EBUSY;
>> + goto free_cdnsp;
>> + }
>> +
>> + cdnsp->dev_regs = devm_ioremap(dev, rsrc_start, rsrc_len);
>> + if (!cdnsp->dev_regs) {
>> + dev_dbg(dev, "error mapping memory\n");
>> + ret = -EFAULT;
>> + goto free_cdnsp;
>> + }
>> +
>> + cdnsp->dev_irq = pdev->irq;
>> + dev_dbg(dev, "USBSS-DEV physical base addr: %pa\n",
>> + &rsrc_start);
>> +
>> + res = &cdnsp->xhci_res[0];
>> + res->start = pci_resource_start(pdev, PCI_BAR_HOST);
>> + res->end = pci_resource_end(pdev, PCI_BAR_HOST);
>> + res->name = "xhci";
>> + res->flags = IORESOURCE_MEM;
>> + dev_dbg(dev, "USBSS-XHCI physical base addr: %pa\n",
>> + &res->start);
>> +
>> + /* Interrupt for XHCI, */
>> + res = &cdnsp->xhci_res[1];
>> + res->start = pdev->irq;
>> + res->name = "host";
>> + res->flags = IORESOURCE_IRQ;
>> + } else {
>> + res = &cdnsp->otg_res;
>> + res->start = pci_resource_start(pdev, PCI_BAR_OTG);
>> + res->end = pci_resource_end(pdev, PCI_BAR_OTG);
>> + res->name = "otg";
>> + res->flags = IORESOURCE_MEM;
>> + dev_dbg(dev, "CDNSP-DRD physical base addr: %pa\n",
>> + &res->start);
>> +
>> + /* Interrupt for OTG/DRD. */
>> + cdnsp->otg_irq = pdev->irq;
>> + }
>> +
>> + if (pci_is_enabled(func)) {
>> + cdnsp->dev = dev;
>> +
>> + ret = cdns_init(cdnsp);
>> + if (ret)
>> + goto free_cdnsp;
>> + }
>> +
>> + pci_set_drvdata(pdev, cdnsp);
>> +
>> + device_wakeup_enable(&pdev->dev);
>> + if (pci_dev_run_wake(pdev))
>> + pm_runtime_put_noidle(&pdev->dev);
>> +
>> + return 0;
>> +
>> +free_cdnsp:
>> + if (!pci_is_enabled(func))
>> + kfree(cdnsp);
>> +
>> +disable_pci:
>> + pci_disable_device(pdev);
>> +
>> +put_pci:
>> + pci_dev_put(func);
>> +
>> + return ret;
>> +}
>> +
>> +static void cdnsp_pci_remove(struct pci_dev *pdev)
>> +{
>> + struct cdns *cdnsp;
>> + struct pci_dev *func;
>> +
>> + func = cdnsp_get_second_fun(pdev);
>> + cdnsp = (struct cdns *)pci_get_drvdata(pdev);
>> +
>> + if (pci_dev_run_wake(pdev))
>> + pm_runtime_get_noresume(&pdev->dev);
>> +
>> + if (!pci_is_enabled(func)) {
>> + kfree(cdnsp);
>> + goto pci_put;
>> + }
>> +
>> + cdns_remove(cdnsp);
>> +
>> +pci_put:
>> + pci_dev_put(func);
>> +}
>> +
>> +static int __maybe_unused cdnsp_pci_suspend(struct device *dev)
>> +{
>> + struct cdns *cdns = dev_get_drvdata(dev);
>> +
>> + return cdns_suspend(cdns);
>> +}
>> +
>> +static int __maybe_unused cdnsp_pci_resume(struct device *dev)
>> +{
>> + struct cdns *cdns = dev_get_drvdata(dev);
>> +
>> + return cdns_resume(cdns);
>> +}
>> +
>> +static const struct dev_pm_ops cdnsp_pci_pm_ops = {
>> + SET_SYSTEM_SLEEP_PM_OPS(cdnsp_pci_suspend, cdnsp_pci_resume)
>> +};
>> +
>> +static const struct pci_device_id cdnsp_pci_ids[] = {
>> + { PCI_VENDOR_ID_CDNS, CDNS_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,
>> + PCI_CLASS_SERIAL_USB_DEVICE, PCI_ANY_ID },
>> + { PCI_VENDOR_ID_CDNS, CDNS_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,
>> + CDNS_DRD_IF, PCI_ANY_ID },
>> + { 0, }
>> +};
>> +
>> +static struct pci_driver cdnsp_pci_driver = {
>> + .name = "cdnsp-pci",
>> + .id_table = &cdnsp_pci_ids[0],
>> + .probe = cdnsp_pci_probe,
>> + .remove = cdnsp_pci_remove,
>> + .driver = {
>> + .pm = &cdnsp_pci_pm_ops,
>> + }
>> +};
>> +
>> +module_pci_driver(cdnsp_pci_driver);
>> +MODULE_DEVICE_TABLE(pci, cdnsp_pci_ids);
>> +
>> +MODULE_ALIAS("pci:cdnsp");
>> +MODULE_AUTHOR("Pawel Laszczak <pawell@...ence.com>");
>> +MODULE_LICENSE("GPL v2");
>> +MODULE_DESCRIPTION("Cadence CDNSP PCI driver");
>> +
>> diff --git a/drivers/usb/cdnsp/ep0.c b/drivers/usb/cdnsp/ep0.c
>> new file mode 100644
>> index 000000000000..7f6e1d28d3b8
>> --- /dev/null
>> +++ b/drivers/usb/cdnsp/ep0.c
>> @@ -0,0 +1,480 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Cadence CDNSP DRD Driver.
>> + *
>> + * Copyright (C) 2020 Cadence.
>> + *
>> + * Author: Pawel Laszczak <pawell@...ence.com>
>> + *
>> + */
>> +
>> +#include <linux/usb/composite.h>
>> +#include <linux/usb/gadget.h>
>> +#include <linux/list.h>
>> +
>> +#include "gadget.h"
>> +
>> +static void cdnsp_ep0_stall(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_request *preq;
>> + struct cdnsp_ep *pep;
>> +
>> + pep = &pdev->eps[0];
>> + preq = next_request(&pep->pending_list);
>> +
>> + if (pdev->three_stage_setup) {
>> + cdnsp_halt_endpoint(pdev, pep, true);
>> +
>> + if (preq)
>> + cdnsp_gadget_giveback(pep, preq, -ECONNRESET);
>> + } else {
>> + pep->ep_state |= EP0_HALTED_STATUS;
>> +
>> + if (preq)
>> + list_del(&preq->list);
>> +
>> + cdnsp_status_stage(pdev);
>> + }
>> +}
>> +
>> +static int cdnsp_ep0_delegate_req(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + int ret;
>> +
>> + spin_unlock(&pdev->lock);
>> + ret = pdev->gadget_driver->setup(&pdev->gadget, ctrl);
>> + spin_lock(&pdev->lock);
>> +
>> + return ret;
>> +}
>> +
>> +static int cdnsp_ep0_set_config(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + enum usb_device_state state = pdev->gadget.state;
>> + u32 cfg;
>> + int ret;
>> +
>> + cfg = le16_to_cpu(ctrl->wValue);
>> +
>> + switch (state) {
>> + case USB_STATE_ADDRESS:
>> + ret = cdnsp_ep0_delegate_req(pdev, ctrl);
>> + if (ret)
>> + return ret;
>> + break;
>> + case USB_STATE_CONFIGURED:
>> + ret = cdnsp_ep0_delegate_req(pdev, ctrl);
>> + if (ret)
>> + return ret;
>What about moving cdnsp_ep0_delegate_req() after switch (), it's the
>same for ADDRESS & CONFIGURED state
I will remove duplicated code by using fallthrough in first case.
I will leave it in switch (). I think that it will be more readable.
>> + break;
>> + default:
>> + dev_err(pdev->dev, "Set Configuration - bad device state\n");
>> + return -EINVAL;
>> + }
>> +
>> + if (!cfg)
>> + usb_gadget_set_state(&pdev->gadget, USB_STATE_ADDRESS);
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_ep0_set_address(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + enum usb_device_state state = pdev->gadget.state;
>> + struct cdnsp_slot_ctx *slot_ctx;
>> + unsigned int slot_state;
>> + int ret;
>> + u32 addr;
>> +
>> + addr = le16_to_cpu(ctrl->wValue);
>> +
>> + if (addr > 127) {
>> + dev_err(pdev->dev, "Invalid device address %d\n", addr);
>> + return -EINVAL;
>> + }
>> +
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx);
>> +
>> + if (state == USB_STATE_CONFIGURED) {
>> + dev_err(pdev->dev, "Can't Set Address from Configured State\n");
>> + return -EINVAL;
>> + }
>> +
>> + pdev->device_address = le16_to_cpu(ctrl->wValue);
>> +
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx);
>> + slot_state = GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state));
>> + if (slot_state == SLOT_STATE_ADDRESSED)
>> + cdnsp_reset_device(pdev);
>> +
>> + /*set device address*/
>> + ret = cdnsp_setup_device(pdev, SETUP_CONTEXT_ADDRESS);
>> + if (ret)
>> + return ret;
>> +
>> + if (addr)
>> + usb_gadget_set_state(&pdev->gadget, USB_STATE_ADDRESS);
>> + else
>> + usb_gadget_set_state(&pdev->gadget, USB_STATE_DEFAULT);
>> +
>> + return 0;
>> +}
>> +
>> +int cdnsp_status_stage(struct cdnsp_device *pdev)
>> +{
>> + pdev->ep0_stage = CDNSP_STATUS_STAGE;
>> + pdev->ep0_preq.request.length = 0;
>> +
>> + return cdnsp_ep_enqueue(pdev->ep0_preq.pep, &pdev->ep0_preq);
>> +}
>> +
>> +static int cdnsp_w_index_to_ep_index(__le32 wIndex)
>> +{
>> + wIndex = le32_to_cpu(wIndex);
>> +
>> + if (!(wIndex & USB_ENDPOINT_NUMBER_MASK))
>> + return 0;
>> +
>> + return ((wIndex & USB_ENDPOINT_NUMBER_MASK) * 2) +
>> + (wIndex & USB_ENDPOINT_DIR_MASK ? 1 : 0) - 1;
>> +}
>> +
>> +static int cdnsp_ep0_handle_status(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + struct cdnsp_ep *pep;
>> + __le16 *response;
>> + int ep_sts = 0;
>> + u16 status = 0;
>> + u32 recipient;
>> +
>> + recipient = ctrl->bRequestType & USB_RECIP_MASK;
>> +
>> + switch (recipient) {
>> + case USB_RECIP_DEVICE:
>> + status = pdev->gadget.is_selfpowered;
>> + status |= pdev->may_wakeup << USB_DEVICE_REMOTE_WAKEUP;
>> +
>> + if (pdev->gadget.speed >= USB_SPEED_SUPER) {
>> + status |= pdev->u1_allowed << USB_DEV_STAT_U1_ENABLED;
>> + status |= pdev->u2_allowed << USB_DEV_STAT_U2_ENABLED;
>> + }
>> + break;
>> + case USB_RECIP_INTERFACE:
>> + /*
>> + * Function Remote Wake Capable D0
>> + * Function Remote Wakeup D1
>> + */
>> + return cdnsp_ep0_delegate_req(pdev, ctrl);
>> + case USB_RECIP_ENDPOINT:
>> + pep = &pdev->eps[cdnsp_w_index_to_ep_index(ctrl->wIndex)];
>> + ep_sts = GET_EP_CTX_STATE(pep->out_ctx);
>> +
>> + /* check if endpoint is stalled */
>> + if (ep_sts == EP_STATE_HALTED)
>> + status = BIT(USB_ENDPOINT_HALT);
>> + break;
>> + default:
>> + return -EINVAL;
>> + }
>> +
>> + response = (__le16 *)pdev->setup_buf;
>> + *response = cpu_to_le16(status);
>> +
>> + pdev->ep0_preq.request.length = sizeof(*response);
>> + pdev->ep0_preq.request.buf = pdev->setup_buf;
>> +
>> + return cdnsp_ep_enqueue(pdev->ep0_preq.pep, &pdev->ep0_preq);
>> +}
>> +
>> +static void cdnsp_enter_test_mode(struct cdnsp_device *pdev)
>> +{
>> + u32 temp;
>> +
>> + temp = readl(&pdev->active_port->regs->portpmsc) & ~GENMASK(31, 28);
>> + temp |= PORT_TEST_MODE(pdev->test_mode);
>> + writel(temp, &pdev->active_port->regs->portpmsc);
>> + pdev->test_mode = 0;
>> +}
>> +
>> +static int cdnsp_ep0_handle_feature_device(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl,
>> + int set)
>> +{
>> + enum usb_device_state state;
>> + enum usb_device_speed speed;
>> + u16 tmode;
>> +
>> + state = pdev->gadget.state;
>> + speed = pdev->gadget.speed;
>> +
>> + switch (le16_to_cpu(ctrl->wValue)) {
>> + case USB_DEVICE_REMOTE_WAKEUP:
>> + pdev->may_wakeup = !!set;
>> + break;
>> + case USB_DEVICE_U1_ENABLE:
>> + if (state != USB_STATE_CONFIGURED || speed < USB_SPEED_SUPER)
>> + return -EINVAL;
>> +
>> + pdev->u1_allowed = !!set;
>> + break;
>> + case USB_DEVICE_U2_ENABLE:
>> + if (state != USB_STATE_CONFIGURED || speed < USB_SPEED_SUPER)
>> + return -EINVAL;
>> +
>> + pdev->u2_allowed = !!set;
>> + break;
>> + case USB_DEVICE_LTM_ENABLE:
>> + return -EINVAL;
>> + case USB_DEVICE_TEST_MODE:
>> + if (state != USB_STATE_CONFIGURED || speed > USB_SPEED_HIGH)
>> + return -EINVAL;
>> +
>> + tmode = le16_to_cpu(ctrl->wIndex);
>> +
>> + if (!set || (tmode & 0xff) != 0)
>> + return -EINVAL;
>> +
>> + tmode = tmode >> 8;
>> +
>> + if (tmode > USB_TEST_FORCE_ENABLE || tmode < USB_TEST_J)
>> + return -EINVAL;
>> +
>> + pdev->test_mode = tmode;
>> +
>> + /*
>> + * Test mode must be set before Status Stage but controller
>> + * will start testing sequence after Status Stage.
>> + */
>> + cdnsp_enter_test_mode(pdev);
>> + break;
>> + default:
>> + return -EINVAL;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_ep0_handle_feature_intf(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl,
>> + int set)
>> +{
>> + u16 wValue, wIndex;
>> + int ret;
>> +
>> + wValue = le16_to_cpu(ctrl->wValue);
>> + wIndex = le16_to_cpu(ctrl->wIndex);
>> +
>> + switch (wValue) {
>> + case USB_INTRF_FUNC_SUSPEND:
>> + ret = cdnsp_ep0_delegate_req(pdev, ctrl);
>> + if (ret)
>> + return ret;
>> +
>> + /*
>> + * Remote wakeup is enabled when any function within a device
>> + * is enabled for function remote wakeup.
>> + */
>> + if (wIndex & USB_INTRF_FUNC_SUSPEND_RW)
>> + pdev->may_wakeup++;
>> + else
>> + if (pdev->may_wakeup > 0)
>> + pdev->may_wakeup--;
>> +
>> + return 0;
>> + default:
>> + return -EINVAL;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_ep0_handle_feature_endpoint(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl,
>> + int set)
>> +{
>> + struct cdnsp_ep *pep;
>> + u32 wValue;
>> +
>> + wValue = le16_to_cpu(ctrl->wValue);
>> + pep = &pdev->eps[cdnsp_w_index_to_ep_index(ctrl->wIndex)];
>> +
>> + switch (wValue) {
>> + case USB_ENDPOINT_HALT:
>> + if (!set && (pep->ep_state & EP_WEDGE)) {
>> + /* Resets Sequence Number */
>> + cdnsp_halt_endpoint(pdev, pep, 0);
>> + cdnsp_halt_endpoint(pdev, pep, 1);
>> + break;
>> + }
>> +
>> + return cdnsp_halt_endpoint(pdev, pep, set);
>> + default:
>> + dev_warn(pdev->dev, "WARN Incorrect wValue %04x\n", wValue);
>> + return -EINVAL;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_ep0_handle_feature(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl,
>> + int set)
>> +{
>> + switch (ctrl->bRequestType & USB_RECIP_MASK) {
>> + case USB_RECIP_DEVICE:
>> + return cdnsp_ep0_handle_feature_device(pdev, ctrl, set);
>> + case USB_RECIP_INTERFACE:
>> + return cdnsp_ep0_handle_feature_intf(pdev, ctrl, set);
>> + case USB_RECIP_ENDPOINT:
>> + return cdnsp_ep0_handle_feature_endpoint(pdev, ctrl, set);
>> + default:
>> + return -EINVAL;
>> + }
>> +}
>> +
>> +static int cdnsp_ep0_set_sel(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + enum usb_device_state state = pdev->gadget.state;
>> + u16 wLength;
>> +
>> + if (state == USB_STATE_DEFAULT)
>> + return -EINVAL;
>> +
>> + wLength = le16_to_cpu(ctrl->wLength);
>> +
>> + if (wLength != 6) {
>> + dev_err(pdev->dev, "Set SEL should be 6 bytes, got %d\n",
>> + wLength);
>> + return -EINVAL;
>> + }
>> +
>> + /*
>> + * To handle Set SEL we need to receive 6 bytes from Host. So let's
>> + * queue a usb_request for 6 bytes.
>> + */
>> + pdev->ep0_preq.request.length = 6;
>> + pdev->ep0_preq.request.buf = pdev->setup_buf;
>> +
>> + return cdnsp_ep_enqueue(pdev->ep0_preq.pep, &pdev->ep0_preq);
>> +}
>> +
>> +static int cdnsp_ep0_set_isoch_delay(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + if (le16_to_cpu(ctrl->wIndex) || le16_to_cpu(ctrl->wLength))
>> + return -EINVAL;
>> +
>> + pdev->gadget.isoch_delay = le16_to_cpu(ctrl->wValue);
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_ep0_std_request(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + int ret;
>> +
>> + switch (ctrl->bRequest) {
>> + case USB_REQ_GET_STATUS:
>> + ret = cdnsp_ep0_handle_status(pdev, ctrl);
>> + break;
>> + case USB_REQ_CLEAR_FEATURE:
>> + ret = cdnsp_ep0_handle_feature(pdev, ctrl, 0);
>> + break;
>> + case USB_REQ_SET_FEATURE:
>> + ret = cdnsp_ep0_handle_feature(pdev, ctrl, 1);
>> + break;
>> + case USB_REQ_SET_ADDRESS:
>> + ret = cdnsp_ep0_set_address(pdev, ctrl);
>> + break;
>> + case USB_REQ_SET_CONFIGURATION:
>> + ret = cdnsp_ep0_set_config(pdev, ctrl);
>> + break;
>> + case USB_REQ_SET_SEL:
>> + ret = cdnsp_ep0_set_sel(pdev, ctrl);
>> + break;
>> + case USB_REQ_SET_ISOCH_DELAY:
>> + ret = cdnsp_ep0_set_isoch_delay(pdev, ctrl);
>> + break;
>> + case USB_REQ_SET_INTERFACE:
>> + /*
>> + * Add request into pending list to block sending status stage
>> + * by libcomposite.
>> + */
>> + list_add_tail(&pdev->ep0_preq.list,
>> + &pdev->ep0_preq.pep->pending_list);
>> +
>> + ret = cdnsp_ep0_delegate_req(pdev, ctrl);
>> + if (ret == -EBUSY)
>> + ret = 0;
>> +
>> + list_del(&pdev->ep0_preq.list);
>> + break;
>> + default:
>> + ret = cdnsp_ep0_delegate_req(pdev, ctrl);
>> + break;
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +void cdnsp_setup_analyze(struct cdnsp_device *pdev)
>> +{
>> + struct usb_ctrlrequest *ctrl = &pdev->setup;
>> + int ret = 0;
>> + __le16 len;
>> +
>> + if (!pdev->gadget_driver)
>> + goto out;
>> +
>> + if (pdev->gadget.state == USB_STATE_NOTATTACHED) {
>> + dev_err(pdev->dev, "ERR: Setup detected in unattached state\n");
>> + ret = -EINVAL;
>> + goto out;
>> + }
>> +
>> + /* Restore the ep0 to Stopped/Running state. */
>> + if (pdev->eps[0].ep_state & EP_HALTED)
>> + cdnsp_halt_endpoint(pdev, &pdev->eps[0], 0);
>> +
>> + /*
>> + * Finishing previous SETUP transfer by removing request from
>> + * list and informing upper layer
>> + */
>> + if (!list_empty(&pdev->eps[0].pending_list)) {
>> + struct cdnsp_request *req;
>> +
>> + req = next_request(&pdev->eps[0].pending_list);
>> + cdnsp_ep_dequeue(&pdev->eps[0], req);
>> + }
>> +
>> + len = le16_to_cpu(ctrl->wLength);
>> + if (!len) {
>> + pdev->three_stage_setup = false;
>> + pdev->ep0_expect_in = false;
>> + } else {
>> + pdev->three_stage_setup = true;
>> + pdev->ep0_expect_in = !!(ctrl->bRequestType & USB_DIR_IN);
>> + }
>> +
>> + if ((ctrl->bRequestType & USB_TYPE_MASK) == USB_TYPE_STANDARD)
>> + ret = cdnsp_ep0_std_request(pdev, ctrl);
>> + else
>> + ret = cdnsp_ep0_delegate_req(pdev, ctrl);
>> +
>> + if (!len)
>> + pdev->ep0_stage = CDNSP_STATUS_STAGE;
>> +
>> + if (ret == USB_GADGET_DELAYED_STATUS)
>> + return;
>> +out:
>> + if (ret < 0)
>> + cdnsp_ep0_stall(pdev);
>> + else if (pdev->ep0_stage == CDNSP_STATUS_STAGE)
>> + cdnsp_status_stage(pdev);
>> +}
>> diff --git a/drivers/usb/cdnsp/gadget.c b/drivers/usb/cdnsp/gadget.c
>> new file mode 100644
>> index 000000000000..38ad170b2bdd
>> --- /dev/null
>> +++ b/drivers/usb/cdnsp/gadget.c
>> @@ -0,0 +1,1946 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Cadence CDNSP DRD Driver.
>> + *
>> + * Copyright (C) 2020 Cadence.
>> + *
>> + * Author: Pawel Laszczak <pawell@...ence.com>
>> + *
>> + */
>> +
>> +#include <linux/moduleparam.h>
>> +#include <linux/dma-mapping.h>
>> +#include <linux/module.h>
>> +#include <linux/iopoll.h>
>> +#include <linux/delay.h>
>> +#include <linux/log2.h>
>> +#include <linux/slab.h>
>> +#include <linux/pci.h>
>> +#include <linux/irq.h>
>> +#include <linux/dmi.h>
>> +
>> +#include "../cdns3/core.h"
>> +#include "../cdns3/gadget-export.h"
>> +#include "../cdns3/drd.h"
>> +#include "gadget.h"
>> +
>> +unsigned int cdnsp_port_speed(unsigned int port_status)
>> +{
>> + /*Detect gadget speed based on PORTSC register*/
>> + if (DEV_SUPERSPEEDPLUS(port_status))
>> + return USB_SPEED_SUPER_PLUS;
>> + else if (DEV_SUPERSPEED(port_status))
>> + return USB_SPEED_SUPER;
>> + else if (DEV_HIGHSPEED(port_status))
>> + return USB_SPEED_HIGH;
>> + else if (DEV_FULLSPEED(port_status))
>> + return USB_SPEED_FULL;
>> +
>> + /* If device is detached then speed will be USB_SPEED_UNKNOWN.*/
>> + return USB_SPEED_UNKNOWN;
>> +}
>> +
>> +/*
>Use /* or /**?
>See doc-guide/kernel-doc.rst
What is wrong here ? I'm used /*. It's only function comment.
/** is used for function documentation. I'm using intentionally
/* in many places before functions.
>> + * Given a port state, this function returns a value that would result in the
>> + * port being in the same state, if the value was written to the port status
>> + * control register.
>> + * Save Read Only (RO) bits and save read/write bits where
>> + * writing a 0 clears the bit and writing a 1 sets the bit (RWS).
>> + * For all other types (RW1S, RW1CS, RW, and RZ), writing a '0' has no effect.
>> + */
>> +u32 cdnsp_port_state_to_neutral(u32 state)
>> +{
>> + /* Save read-only status and port state. */
>> + return (state & CDNSP_PORT_RO) | (state & CDNSP_PORT_RWS);
>> +}
>> +
>> +/**
>> + * Find the offset of the extended capabilities with capability ID id.
>> + * @base: PCI MMIO registers base address.
>> + * @start: Address at which to start looking, (0 or HCC_PARAMS to start at
>> + * beginning of list)
>> + * @id: Extended capability ID to search for.
>> + *
>> + * Returns the offset of the next matching extended capability structure.
>> + * Some capabilities can occur several times,
>> + * e.g., the EXT_CAPS_PROTOCOL, and this provides a way to find them all.
>> + */
>> +int cdnsp_find_next_ext_cap(void __iomem *base, u32 start, int id)
>> +{
>> + u32 offset = start;
>> + u32 next;
>> + u32 val;
>> +
>> + if (!start || start == HCC_PARAMS_OFFSET) {
>> + val = readl(base + HCC_PARAMS_OFFSET);
>> + if (val == ~0)
>> + return 0;
>> +
>> + offset = HCC_EXT_CAPS(val) << 2;
>> + if (!offset)
>> + return 0;
>> + };
>> +
>> + do {
>> + val = readl(base + offset);
>> + if (val == ~0)
>> + return 0;
>> +
>> + if (EXT_CAPS_ID(val) == id && offset != start)
>> + return offset;
>> +
>> + next = EXT_CAPS_NEXT(val);
>> + offset += next << 2;
>> + } while (next);
>> +
>> + return 0;
>> +}
>> +
>> +void cdnsp_set_link_state(struct cdnsp_device *pdev,
>> + __le32 __iomem *port_regs,
>> + u32 link_state)
>> +{
>> + u32 temp;
>> +
>> + temp = readl(port_regs);
>> + temp = cdnsp_port_state_to_neutral(temp);
>> + temp |= PORT_WKCONN_E | PORT_WKDISC_E;
>> + writel(temp, port_regs);
>> +
>> + temp &= ~PORT_PLS_MASK;
>> + temp |= PORT_LINK_STROBE | link_state;
>> +
>> + writel(temp, port_regs);
>> +}
>> +
>> +static void cdnsp_disable_port(struct cdnsp_device *pdev,
>> + __le32 __iomem *port_regs)
>> +{
>> + u32 temp = cdnsp_port_state_to_neutral(readl(port_regs));
>> +
>> + writel(temp | PORT_PED, port_regs);
>> +}
>> +
>> +static void cdnsp_clear_port_change_bit(struct cdnsp_device *pdev,
>> + __le32 __iomem *port_regs)
>> +{
>> + u32 portsc = readl(port_regs);
>> +
>> + writel(cdnsp_port_state_to_neutral(portsc) |
>> + (portsc & PORT_CHANGE_BITS), port_regs);
>> +}
>> +
>> +static void cdnsp_set_chicken_bits_2(struct cdnsp_device *pdev, u32 bit)
>> +{
>> + __le32 __iomem *reg;
>> + void __iomem *base;
>> + u32 offset = 0;
>> +
>> + base = &pdev->cap_regs->hc_capbase;
>> + offset = cdnsp_find_next_ext_cap(base, offset, D_XEC_PRE_REGS_CAP);
>> + reg = base + offset + REG_CHICKEN_BITS_2_OFFSET;
>> +
>> + bit = readl(reg) | bit;
>> + writel(bit, reg);
>> +}
>> +
>> +static void cdnsp_clear_chicken_bits_2(struct cdnsp_device *pdev, u32 bit)
>> +{
>> + __le32 __iomem *reg;
>> + void __iomem *base;
>> + u32 offset = 0;
>> +
>> + base = &pdev->cap_regs->hc_capbase;
>> + offset = cdnsp_find_next_ext_cap(base, offset, D_XEC_PRE_REGS_CAP);
>> + reg = base + offset + REG_CHICKEN_BITS_2_OFFSET;
>> +
>> + bit = readl(reg) & ~bit;
>> + writel(bit, reg);
>> +}
>> +
>> +/*
>> + * Disable interrupts and begin the controller halting process.
>> + */
>> +static void cdnsp_quiesce(struct cdnsp_device *pdev)
>> +{
>> + u32 halted;
>> + u32 mask;
>> + u32 cmd;
>> +
>> + mask = ~(u32)(CDNSP_IRQS);
>> +
>> + halted = readl(&pdev->op_regs->status) & STS_HALT;
>> + if (!halted)
>> + mask &= ~(CMD_R_S | CMD_DEVEN);
>> +
>> + cmd = readl(&pdev->op_regs->command);
>> + cmd &= mask;
>> + writel(cmd, &pdev->op_regs->command);
>> +}
>> +
>> +/*
>> + * Force controller into halt state.
>> + *
>> + * Disable any IRQs and clear the run/stop bit.
>> + * Controller will complete any current and actively pipelined transactions, and
>> + * should halt within 16 ms of the run/stop bit being cleared.
>> + * Read controller Halted bit in the status register to see when the
>> + * controller is finished.
>> + */
>> +int cdnsp_halt(struct cdnsp_device *pdev)
>> +{
>> + int ret;
>> + u32 val;
>> +
>> + cdnsp_quiesce(pdev);
>> +
>> + ret = readl_poll_timeout_atomic(&pdev->op_regs->status, val,
>> + val & STS_HALT, 1,
>> + CDNSP_MAX_HALT_USEC);
>> + if (ret) {
>> + dev_err(pdev->dev, "ERROR: Device halt failed\n");
>> + return ret;
>> + }
>> +
>> + pdev->cdnsp_state |= CDNSP_STATE_HALTED;
>> +
>> + return 0;
>> +}
>> +
>> +/*
>> + * device controller died, register read returns 0xffffffff, or command never
>> + * ends.
>> + */
>> +void cdnsp_died(struct cdnsp_device *pdev)
>> +{
>> + dev_err(pdev->dev, "ERROR: CDNSP controller not responding\n");
>> + pdev->cdnsp_state |= CDNSP_STATE_DYING;
>> + cdnsp_halt(pdev);
>> +}
>> +
>> +/*
>> + * Set the run bit and wait for the device to be running.
>> + */
>> +static int cdnsp_start(struct cdnsp_device *pdev)
>> +{
>> + u32 temp;
>> + int ret;
>> +
>> + temp = readl(&pdev->op_regs->command);
>> + temp |= (CMD_R_S | CMD_DEVEN);
>> + writel(temp, &pdev->op_regs->command);
>> +
>> + pdev->cdnsp_state = 0;
>> +
>> + /*
>> + * Wait for the STS_HALT Status bit to be 0 to indicate the device is
>> + * running.
>> + */
>> + ret = readl_poll_timeout_atomic(&pdev->op_regs->status, temp,
>> + !(temp & STS_HALT), 1,
>> + CDNSP_MAX_HALT_USEC);
>> + if (ret) {
>> + pdev->cdnsp_state = CDNSP_STATE_DYING;
>> + dev_err(pdev->dev, "ERROR: Controller run failed\n");
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * Reset a halted controller.
>> + *
>> + * This resets pipelines, timers, counters, state machines, etc.
>> + * Transactions will be terminated immediately, and operational registers
>> + * will be set to their defaults.
>> + */
>> +int cdnsp_reset(struct cdnsp_device *pdev)
>> +{
>> + u32 command;
>> + u32 temp;
>> + int ret;
>> +
>> + temp = readl(&pdev->op_regs->status);
>> +
>> + if (temp == ~(u32)0) {
>> + dev_err(pdev->dev, "Device not accessible, reset failed.\n");
>> + return -ENODEV;
>> + }
>> +
>> + if ((temp & STS_HALT) == 0) {
>> + dev_err(pdev->dev, "Controller not halted, aborting reset.\n");
>> + return -EINVAL;
>> + }
>> +
>> + command = readl(&pdev->op_regs->command);
>> + command |= CMD_RESET;
>> + writel(command, &pdev->op_regs->command);
>> +
>> + ret = readl_poll_timeout_atomic(&pdev->op_regs->command, temp,
>> + !(temp & CMD_RESET), 1,
>> + 10 * 1000);
>> + if (ret) {
>> + dev_err(pdev->dev, "ERROR: Controller reset failed\n");
>> + return ret;
>> + }
>> +
>> + /*
>> + * CDNSP cannot write any doorbells or operational registers other
>> + * than status until the "Controller Not Ready" flag is cleared.
>> + */
>> + ret = readl_poll_timeout_atomic(&pdev->op_regs->status, temp,
>> + !(temp & STS_CNR), 1,
>> + 10 * 1000);
>> +
>> + if (ret) {
>> + dev_err(pdev->dev, "ERROR: Controller not ready to work\n");
>> + return ret;
>> + }
>> +
>> + dev_info(pdev->dev, "Controller ready to work");
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * cdnsp_get_endpoint_index - Find the index for an endpoint given its
>> + * descriptor.Use the return value to right shift 1 for the bitmask.
>> + *
>> + * Index = (epnum * 2) + direction - 1,
>> + * where direction = 0 for OUT, 1 for IN.
>> + * For control endpoints, the IN index is used (OUT index is unused), so
>> + * index = (epnum * 2) + direction - 1 = (epnum * 2) + 1 - 1 = (epnum * 2)
>> + */
>> +static unsigned int
>> + cdnsp_get_endpoint_index(const struct usb_endpoint_descriptor *desc)
>> +{
>> + unsigned int index = (unsigned int)usb_endpoint_num(desc);
>> +
>> + if (usb_endpoint_xfer_control(desc))
>> + return index * 2;
>> +
>> + return (index * 2) + (usb_endpoint_dir_in(desc) ? 1 : 0) - 1;
>> +}
>> +
>> +/*
>> + * Find the flag for this endpoint (for use in the control context). Use the
>> + * endpoint index to create a bitmask. The slot context is bit 0, endpoint 0 is
>> + * bit 1, etc.
>> + */
>> +static unsigned int
>> + cdnsp_get_endpoint_flag(const struct usb_endpoint_descriptor *desc)
>> +{
>> + return 1 << (cdnsp_get_endpoint_index(desc) + 1);
>> +}
>> +
>> +int cdnsp_ep_enqueue(struct cdnsp_ep *pep, struct cdnsp_request *preq)
>> +{
>> + struct cdnsp_device *pdev = pep->pdev;
>> + struct usb_request *request;
>> + int ret;
>> +
>> + if (preq->epnum == 0 && !list_empty(&pep->pending_list))
>> + return -EBUSY;
>> +
>> + request = &preq->request;
>> + request->actual = 0;
>> + request->status = -EINPROGRESS;
>> + preq->direction = pep->direction;
>> + preq->epnum = pep->number;
>> + preq->td.drbl = 0;
>> +
>> + ret = usb_gadget_map_request_by_dev(pdev->dev, request, pep->direction);
>> + if (ret)
>> + return ret;
>> +
>> + list_add_tail(&preq->list, &pep->pending_list);
>> +
>> + switch (usb_endpoint_type(pep->endpoint.desc)) {
>> + case USB_ENDPOINT_XFER_CONTROL:
>> + ret = cdnsp_queue_ctrl_tx(pdev, preq);
>> + break;
>> + case USB_ENDPOINT_XFER_BULK:
>> + case USB_ENDPOINT_XFER_INT:
>> + ret = cdnsp_queue_bulk_tx(pdev, preq);
>> + break;
>> + case USB_ENDPOINT_XFER_ISOC:
>> + ret = cdnsp_queue_isoc_tx_prepare(pdev, preq);
>> + }
>> +
>> + if (ret)
>> + goto unmap;
>> +
>> + return 0;
>> +
>> +unmap:
>> + usb_gadget_unmap_request_by_dev(pdev->dev, &preq->request,
>> + pep->direction);
>> + list_del(&preq->list);
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * Remove the request's TD from the endpoint ring. This may cause the
>> + * controller to stop USB transfers, potentially stopping in the middle of a
>> + * TRB buffer. The controller should pick up where it left off in the TD,
>> + * unless a Set Transfer Ring Dequeue Pointer is issued.
>> + *
>> + * The TRBs that make up the buffers for the canceled request will be "removed"
>> + * from the ring. Since the ring is a contiguous structure, they can't be
>> + * physically removed. Instead, there are two options:
>> + *
>> + * 1) If the controller is in the middle of processing the request to be
>> + * canceled, we simply move the ring's dequeue pointer past those TRBs
>> + * using the Set Transfer Ring Dequeue Pointer command. This will be
>> + * the common case, when drivers timeout on the last submitted request
>> + * and attempt to cancel.
>> + *
>> + * 2) If the controller is in the middle of a different TD, we turn the TRBs
>> + * into a series of 1-TRB transfer no-op TDs. No-ops shouldn't be chained.
>> + * The controller will need to invalidate the any TRBs it has cached after
>> + * the stop endpoint command.
>> + *
>> + * 3) The TD may have completed by the time the Stop Endpoint Command
>> + * completes, so software needs to handle that case too.
>> + *
>> + */
>> +int cdnsp_ep_dequeue(struct cdnsp_ep *pep, struct cdnsp_request *preq)
>> +{
>> + struct cdnsp_device *pdev = pep->pdev;
>> + int ret;
>> +
>> + if (GET_EP_CTX_STATE(pep->out_ctx) == EP_STATE_RUNNING) {
>> + ret = cdnsp_cmd_stop_ep(pdev, pep);
>> + if (ret)
>> + return ret;
>> + }
>> +
>> + return cdnsp_remove_request(pdev, preq, pep);
>> +}
>> +
>> +static void cdnsp_zero_in_ctx(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_input_control_ctx *ctrl_ctx;
>> + struct cdnsp_slot_ctx *slot_ctx;
>> + struct cdnsp_ep_ctx *ep_ctx;
>> + int i;
>> +
>> + ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx);
>> +
>> + /*
>> + * When a device's add flag and drop flag are zero, any subsequent
>> + * configure endpoint command will leave that endpoint's state
>> + * untouched. Make sure we don't leave any old state in the input
>> + * endpoint contexts.
>> + */
>> + ctrl_ctx->drop_flags = 0;
>> + ctrl_ctx->add_flags = 0;
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx);
>> + slot_ctx->dev_info &= cpu_to_le32(~LAST_CTX_MASK);
>> +
>> + /* Endpoint 0 is always valid */
>> + slot_ctx->dev_info |= cpu_to_le32(LAST_CTX(1));
>> + for (i = 1; i < 31; ++i) {
>> + ep_ctx = cdnsp_get_ep_ctx(&pdev->in_ctx, i);
>> + ep_ctx->ep_info = 0;
>> + ep_ctx->ep_info2 = 0;
>> + ep_ctx->deq = 0;
>> + ep_ctx->tx_info = 0;
>> + }
>> +}
>> +
>> +/* Issue a configure endpoint command and wait for it to finish. */
>> +static int cdnsp_configure_endpoint(struct cdnsp_device *pdev)
>> +{
>> + int ret;
>> +
>> + cdnsp_queue_configure_endpoint(pdev, pdev->cmd.in_ctx->dma);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> + if (ret) {
>> + dev_err(pdev->dev,
>> + "ERR: unexpected command completion code 0x%x.\n", ret);
>> + return -EINVAL;
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +static void cdnsp_invalidate_ep_events(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep)
>> +{
>> + struct cdnsp_segment *segment;
>> + union cdnsp_trb *event;
>> + u32 cycle_state;
>> + __le32 data;
>> +
>> + event = pdev->event_ring->dequeue;
>> + segment = pdev->event_ring->deq_seg;
>> + cycle_state = pdev->event_ring->cycle_state;
>> +
>> + while (1) {
>> + data = le32_to_cpu(event->trans_event.flags);
>> +
>> + /* Check the owner of the TRB. */
>> + if ((data & TRB_CYCLE) != cycle_state)
>> + break;
>> +
>> + if (TRB_FIELD_TO_TYPE(data) == TRB_TRANSFER &&
>> + TRB_TO_EP_ID(data) == (pep->idx + 1)) {
>> + data |= TRB_EVENT_INVALIDATE;
>> + event->trans_event.flags = cpu_to_le32(data);
>> + }
>> +
>> + if (cdnsp_last_trb_on_seg(segment, event)) {
>> + cycle_state ^= 1;
>> + segment = pdev->event_ring->deq_seg->next;
>> + event = segment->trbs;
>> + } else {
>> + event++;
>> + }
>> + }
>> +}
>> +
>> +int cdnsp_wait_for_cmd_compl(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_segment *event_deq_seg;
>> + dma_addr_t cmd_deq_dma;
>> + union cdnsp_trb *cmd_trb;
>> + union cdnsp_trb *event;
>> + u32 cycle_state;
>> + __le32 flags;
>> + int ret, val;
>> + u64 cmd_dma;
>> +
>> + cmd_trb = pdev->cmd.command_trb;
>> + pdev->cmd.status = 0;
>> +
>> + ret = readl_poll_timeout_atomic(&pdev->op_regs->cmd_ring, val,
>> + !CMD_RING_BUSY(val), 1,
>> + CDNSP_CMD_TIMEOUT);
>> + if (ret) {
>> + dev_err(pdev->dev, "ERR: Timeout while waiting for command\n");
>> + pdev->cdnsp_state = CDNSP_STATE_DYING;
>> + return -ETIMEDOUT;
>> + }
>> +
>> + event = pdev->event_ring->dequeue;
>> + event_deq_seg = pdev->event_ring->deq_seg;
>> + cycle_state = pdev->event_ring->cycle_state;
>> +
>> + cmd_deq_dma = cdnsp_trb_virt_to_dma(pdev->cmd_ring->deq_seg, cmd_trb);
>> + if (!cmd_deq_dma)
>> + return -EINVAL;
>> +
>> + while (1) {
>> + flags = le32_to_cpu(event->event_cmd.flags);
>> +
>> + /* Check the owner of the TRB. */
>> + if ((flags & TRB_CYCLE) != cycle_state)
>> + return -EINVAL;
>> +
>> + cmd_dma = le64_to_cpu(event->event_cmd.cmd_trb);
>> +
>> + /*
>> + * Check whether the completion event is for last queued
>> + * command.
>> + */
>> + if (TRB_FIELD_TO_TYPE(flags) != TRB_COMPLETION ||
>> + cmd_dma != (u64)cmd_deq_dma) {
>> + if (!cdnsp_last_trb_on_seg(event_deq_seg, event)) {
>> + event++;
>> + continue;
>> + }
>> +
>> + if (cdnsp_last_trb_on_ring(pdev->event_ring,
>> + event_deq_seg, event))
>> + cycle_state ^= 1;
>> +
>> + event_deq_seg = event_deq_seg->next;
>> + event = event_deq_seg->trbs;
>> + continue;
>> + }
>> +
>> + pdev->cmd.status = GET_COMP_CODE(le32_to_cpu(event->event_cmd.status));
>> + if (pdev->cmd.status == COMP_SUCCESS)
>> + return 0;
>
>> +
>> + return -pdev->cmd.status;
>> + }
>> +
>> + return 0;
>Maybe no need if no break in while()
Yes, it's not needed.
>> +}
>> +
>> +int cdnsp_halt_endpoint(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep,
>> + int value)
>> +{
>> + int ret;
>> +
>> + if (value) {
>> + ret = cdnsp_cmd_stop_ep(pdev, pep);
>> + if (ret)
>> + return ret;
>> +
>> + if (GET_EP_CTX_STATE(pep->out_ctx) == EP_STATE_STOPPED) {
>> + cdnsp_queue_halt_endpoint(pdev, pep->idx);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> + }
>> +
>> + pep->ep_state |= EP_HALTED;
>> + } else {
>> + /*
>> + * In device mode driver can call reset endpoint command
>> + * from any endpoint state.
>> + */
>> + cdnsp_queue_reset_ep(pdev, pep->idx);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> + if (ret)
>> + return ret;
>> +
>> + pep->ep_state &= ~EP_HALTED;
>> +
>> + if (pep->idx != 0 && !(pep->ep_state & EP_WEDGE))
>> + cdnsp_ring_doorbell_for_active_rings(pdev, pep);
>> +
>> + pep->ep_state &= ~EP_WEDGE;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_update_eps_configuration(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep)
>> +{
>> + struct cdnsp_input_control_ctx *ctrl_ctx;
>> + struct cdnsp_slot_ctx *slot_ctx;
>> + int ret = 0;
>> + u32 ep_sts;
>> + int i;
>> +
>> + ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx);
>> +
>> + /* Don't issue the command if there's no endpoints to update. */
>> + if (ctrl_ctx->add_flags == 0 && ctrl_ctx->drop_flags == 0)
>> + return 0;
>> +
>> + ctrl_ctx->add_flags |= cpu_to_le32(SLOT_FLAG);
>> + ctrl_ctx->add_flags &= cpu_to_le32(~EP0_FLAG);
>> + ctrl_ctx->drop_flags &= cpu_to_le32(~(SLOT_FLAG | EP0_FLAG));
>> +
>> + /* Fix up Context Entries field. Minimum value is EP0 == BIT(1). */
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx);
>> + for (i = 31; i >= 1; i--) {
>> + __le32 le32 = cpu_to_le32(BIT(i));
>> +
>> + if ((pdev->eps[i - 1].ring && !(ctrl_ctx->drop_flags & le32)) ||
>> + (ctrl_ctx->add_flags & le32) || i == 1) {
>> + slot_ctx->dev_info &= cpu_to_le32(~LAST_CTX_MASK);
>> + slot_ctx->dev_info |= cpu_to_le32(LAST_CTX(i));
>> + break;
>> + }
>> + }
>> +
>> + ep_sts = GET_EP_CTX_STATE(pep->out_ctx);
>> +
>> + if ((ctrl_ctx->add_flags != cpu_to_le32(SLOT_FLAG) &&
>> + ep_sts == EP_STATE_DISABLED) ||
>> + (ep_sts != EP_STATE_DISABLED && ctrl_ctx->drop_flags))
>> + ret = cdnsp_configure_endpoint(pdev);
>> +
>> + cdnsp_zero_in_ctx(pdev);
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * This submits a Reset Device Command, which will set the device state to 0,
>> + * set the device address to 0, and disable all the endpoints except the default
>> + * control endpoint. The USB core should come back and call
>> + * cdnsp_setup_device(), and then re-set up the configuration.
>> + */
>> +int cdnsp_reset_device(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_slot_ctx *slot_ctx;
>> + int slot_state;
>> + int ret, i;
>> +
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx);
>> + slot_ctx->dev_info = 0;
>> + pdev->device_address = 0;
>> +
>> + /* If device is not setup, there is no point in resetting it. */
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx);
>> + slot_state = GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state));
>> +
>> + if (slot_state <= SLOT_STATE_DEFAULT &&
>> + pdev->eps[0].ep_state & EP_HALTED) {
>> + cdnsp_halt_endpoint(pdev, &pdev->eps[0], 0);
>> + }
>> +
>> + /*
>> + * During Reset Device command controller shall transition the
>> + * endpoint ep0 to the Running State.
>> + */
>> + pdev->eps[0].ep_state &= ~(EP_STOPPED | EP_HALTED);
>> + pdev->eps[0].ep_state |= EP_ENABLED;
>> +
>> + if (slot_state <= SLOT_STATE_DEFAULT)
>> + return 0;
>> +
>> + cdnsp_queue_reset_device(pdev);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> +
>> + /*
>> + * After Reset Device command all not default endpoints
>> + * are in Disabled state.
>> + */
>> + for (i = 1; i < 31; ++i)
>> + pdev->eps[i].ep_state |= EP_STOPPED;
>> +
>> + if (ret)
>> + dev_err(pdev->dev, "Reset device failed with error code %d",
>> + ret);
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * Sets the MaxPStreams field and the Linear Stream Array field.
>> + * Sets the dequeue pointer to the stream context array.
>> + */
>> +static void cdnsp_setup_streams_ep_input_ctx(struct cdnsp_device *pdev,
>> + struct cdnsp_ep_ctx *ep_ctx,
>> + struct cdnsp_stream_info *stream_info)
>> +{
>> + u32 max_primary_streams;
>> +
>> + /* MaxPStreams is the number of stream context array entries, not the
>> + * number we're actually using. Must be in 2^(MaxPstreams + 1) format.
>> + * fls(0) = 0, fls(0x1) = 1, fls(0x10) = 2, fls(0x100) = 3, etc.
>> + */
>> + max_primary_streams = fls(stream_info->num_stream_ctxs) - 2;
>> + ep_ctx->ep_info &= cpu_to_le32(~EP_MAXPSTREAMS_MASK);
>> + ep_ctx->ep_info |= cpu_to_le32(EP_MAXPSTREAMS(max_primary_streams)
>> + | EP_HAS_LSA);
>> + ep_ctx->deq = cpu_to_le64(stream_info->ctx_array_dma);
>> +}
>> +
>> +/*
>> + * The drivers use this function to prepare a bulk endpoints to use streams.
>> + *
>> + * Don't allow the call to succeed if endpoint only supports one stream
>> + * (which means it doesn't support streams at all).
>> + */
>> +int cdnsp_alloc_streams(struct cdnsp_device *pdev, struct cdnsp_ep *pep)
>> +{
>> + unsigned int num_streams = usb_ss_max_streams(pep->endpoint.comp_desc);
>> + unsigned int num_stream_ctxs;
>> + int ret;
>> +
>> + if (num_streams == 0)
>> + return 0;
>> +
>> + if (num_streams > STREAM_NUM_STREAMS)
>> + return -EINVAL;
>> +
>> + /*
>> + * Add two to the number of streams requested to account for
>> + * stream 0 that is reserved for controller usage and one additional
>> + * for TASK SET FULL response.
>> + */
>> + num_streams += 2;
>> +
>> + /* The stream context array size must be a power of two */
>> + num_stream_ctxs = roundup_pow_of_two(num_streams);
>> +
>> + ret = cdnsp_alloc_stream_info(pdev, pep, num_stream_ctxs, num_streams);
>> + if (ret)
>> + return ret;
>> +
>> + cdnsp_setup_streams_ep_input_ctx(pdev, pep->in_ctx, &pep->stream_info);
>> +
>> + pep->ep_state |= EP_HAS_STREAMS;
>> + pep->stream_info.td_count = 0;
>> + pep->stream_info.first_prime_det = 0;
>> +
>> + /* Subtract 1 for stream 0, which drivers can't use. */
>> + return num_streams - 1;
>> +}
>> +
>> +int cdnsp_disable_slot(struct cdnsp_device *pdev)
>> +{
>> + int ret;
>> +
>> + cdnsp_queue_slot_control(pdev, TRB_DISABLE_SLOT);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> +
>> + pdev->slot_id = 0;
>> + pdev->active_port = NULL;
>> +
>> + memset(pdev->in_ctx.bytes, 0, CDNSP_CTX_SIZE);
>> + memset(pdev->out_ctx.bytes, 0, CDNSP_CTX_SIZE);
>> +
>> + return ret;
>> +}
>> +
>> +int cdnsp_enable_slot(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_slot_ctx *slot_ctx;
>> + int slot_state;
>> + int ret;
>> +
>> + /* If device is not setup, there is no point in resetting it */
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx);
>> + slot_state = GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state));
>> +
>> + if (slot_state != SLOT_STATE_DISABLED)
>> + return 0;
>> +
>> + cdnsp_queue_slot_control(pdev, TRB_ENABLE_SLOT);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> + if (ret)
>> + return ret;
>> +
>> + pdev->slot_id = 1;
>> +
>> + return 0;
>> +}
>> +
>> +/*
>> + * Issue an Address Device command with BSR=0 if setup is SETUP_CONTEXT_ONLY
>> + * or with BSR = 1 if set_address is SETUP_CONTEXT_ADDRESS.
>> + */
>> +int cdnsp_setup_device(struct cdnsp_device *pdev, enum cdnsp_setup_dev setup)
>> +{
>> + struct cdnsp_input_control_ctx *ctrl_ctx;
>> + struct cdnsp_slot_ctx *slot_ctx;
>> + int dev_state = 0;
>> + int ret;
>> +
>> + if (!pdev->slot_id)
>> + return -EINVAL;
>> +
>> + if (!pdev->active_port->port_num)
>> + return -EINVAL;
>> +
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx);
>> + dev_state = GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state));
>> +
>> + if (setup == SETUP_CONTEXT_ONLY && dev_state == SLOT_STATE_DEFAULT)
>> + return 0;
>> +
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx);
>> + ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx);
>> +
>> + if (!slot_ctx->dev_info || dev_state == SLOT_STATE_DEFAULT) {
>> + ret = cdnsp_setup_addressable_priv_dev(pdev);
>> + if (ret)
>> + return ret;
>> + }
>> +
>> + cdnsp_copy_ep0_dequeue_into_input_ctx(pdev);
>> +
>> + ctrl_ctx->add_flags = cpu_to_le32(SLOT_FLAG | EP0_FLAG);
>> + ctrl_ctx->drop_flags = 0;
>> +
>> + cdnsp_queue_address_device(pdev, pdev->in_ctx.dma, setup);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> +
>> + /* Zero the input context control for later use. */
>> + ctrl_ctx->add_flags = 0;
>> + ctrl_ctx->drop_flags = 0;
>> +
>> + return ret;
>> +}
>> +
>> +void cdnsp_set_usb2_hardware_lpm(struct cdnsp_device *pdev,
>> + struct usb_request *req,
>> + int enable)
>> +{
>> + if (pdev->active_port != &pdev->usb2_port || !pdev->gadget.lpm_capable)
>> + return;
>> +
>> + if (enable)
>> + writel(PORT_BESL(CDNSP_DEFAULT_BESL) | PORT_L1S_NYET | PORT_HLE,
>> + &pdev->active_port->regs->portpmsc);
>> + else
>> + writel(PORT_L1S_NYET, &pdev->active_port->regs->portpmsc);
>> +}
>> +
>> +static int cdnsp_get_frame(struct cdnsp_device *pdev)
>> +{
>> + return readl(&pdev->run_regs->microframe_index) >> 3;
>> +}
>> +
>> +static int cdnsp_gadget_ep_enable(struct usb_ep *ep,
>> + const struct usb_endpoint_descriptor *desc)
>> +{
>> + struct cdnsp_input_control_ctx *ctrl_ctx;
>> + struct cdnsp_device *pdev;
>> + struct cdnsp_ep *pep;
>> + unsigned long flags;
>> + u32 added_ctxs;
>> + int ret;
>> +
>> + if (!ep || !desc || desc->bDescriptorType != USB_DT_ENDPOINT ||
>> + !desc->wMaxPacketSize)
>> + return -EINVAL;
>> +
>> + pep = to_cdnsp_ep(ep);
>> + pdev = pep->pdev;
>> +
>> + if (dev_WARN_ONCE(pdev->dev, pep->ep_state & EP_ENABLED,
>> + "%s is already enabled\n", pep->name))
>> + return 0;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> +
>> + added_ctxs = cdnsp_get_endpoint_flag(desc);
>> + if (added_ctxs == SLOT_FLAG || added_ctxs == EP0_FLAG) {
>> + dev_err(pdev->dev, "ERROR: Bad endpoint number\n");
>> + ret = -EINVAL;
>> + goto unlock;
>> + }
>> +
>> + pep->interval = desc->bInterval ? BIT(desc->bInterval - 1) : 0;
>> +
>> + if (pdev->gadget.speed == USB_SPEED_FULL) {
>> + if (usb_endpoint_type(desc) == USB_ENDPOINT_XFER_INT)
>> + pep->interval = desc->bInterval << 3;
>> + if (usb_endpoint_type(desc) == USB_ENDPOINT_XFER_ISOC)
>> + pep->interval = BIT(desc->bInterval - 1) << 3;
>> + }
>> +
>> + if (usb_endpoint_type(desc) == USB_ENDPOINT_XFER_ISOC) {
>> + if (pep->interval > BIT(12)) {
>> + dev_err(pdev->dev, "bInterval %d not supported\n",
>> + desc->bInterval);
>> + ret = -EINVAL;
>> + goto unlock;
>> + }
>> + cdnsp_set_chicken_bits_2(pdev, CHICKEN_XDMA_2_TP_CACHE_DIS);
>> + }
>> +
>> + ret = cdnsp_endpoint_init(pdev, pep, GFP_ATOMIC);
>> + if (ret)
>> + goto unlock;
>> +
>> + ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx);
>> + ctrl_ctx->add_flags = cpu_to_le32(added_ctxs);
>> + ctrl_ctx->drop_flags = 0;
>> +
>> + ret = cdnsp_update_eps_configuration(pdev, pep);
>> + if (ret) {
>> + cdnsp_free_endpoint_rings(pdev, pep);
>> + goto unlock;
>> + }
>> +
>> + pep->ep_state |= EP_ENABLED;
>> + pep->ep_state &= ~EP_STOPPED;
>> +
>> +unlock:
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return ret;
>> +}
>> +
>> +static int cdnsp_gadget_ep_disable(struct usb_ep *ep)
>> +{
>> + struct cdnsp_input_control_ctx *ctrl_ctx;
>> + struct cdnsp_request *preq;
>> + struct cdnsp_device *pdev;
>> + struct cdnsp_ep *pep;
>> + unsigned long flags;
>> + u32 drop_flag;
>> + int ret = 0;
>> +
>> + if (!ep)
>> + return -EINVAL;
>> +
>> + pep = to_cdnsp_ep(ep);
>> + pdev = pep->pdev;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> +
>> + if (!(pep->ep_state & EP_ENABLED)) {
>> + dev_err(pdev->dev, "%s is already disabled\n", pep->name);
>> + ret = -EINVAL;
>> + goto finish;
>> + }
>> +
>> + cdnsp_cmd_stop_ep(pdev, pep);
>> + pep->ep_state |= EP_DIS_IN_RROGRESS;
>> + cdnsp_cmd_flush_ep(pdev, pep);
>> +
>> + /* Remove all queued USB requests. */
>> + while (!list_empty(&pep->pending_list)) {
>> + preq = next_request(&pep->pending_list);
>> + cdnsp_ep_dequeue(pep, preq);
>> + }
>> +
>> + cdnsp_invalidate_ep_events(pdev, pep);
>> +
>> + pep->ep_state &= ~EP_DIS_IN_RROGRESS;
>> + drop_flag = cdnsp_get_endpoint_flag(pep->endpoint.desc);
>> + ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx);
>> + ctrl_ctx->drop_flags = cpu_to_le32(drop_flag);
>> + ctrl_ctx->add_flags = 0;
>> +
>> + cdnsp_endpoint_zero(pdev, pep);
>> +
>> + ret = cdnsp_update_eps_configuration(pdev, pep);
>> + cdnsp_free_endpoint_rings(pdev, pep);
>> +
>> + pep->ep_state &= ~EP_ENABLED;
>> + pep->ep_state |= EP_STOPPED;
>> +
>> +finish:
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return ret;
>> +}
>> +
>> +static struct usb_request *cdnsp_gadget_ep_alloc_request(struct usb_ep *ep,
>> + gfp_t gfp_flags)
>> +{
>> + struct cdnsp_ep *pep = to_cdnsp_ep(ep);
>> + struct cdnsp_request *preq;
>> +
>> + preq = kzalloc(sizeof(*preq), gfp_flags);
>> + if (!preq)
>> + return NULL;
>> +
>> + preq->epnum = pep->number;
>> + preq->pep = pep;
>> +
>> + return &preq->request;
>> +}
>> +
>> +static void cdnsp_gadget_ep_free_request(struct usb_ep *ep,
>> + struct usb_request *request)
>> +{
>> + struct cdnsp_request *preq = to_cdnsp_request(request);
>> +
>> + kfree(preq);
>> +}
>> +
>> +static int cdnsp_gadget_ep_queue(struct usb_ep *ep,
>> + struct usb_request *request,
>> + gfp_t gfp_flags)
>> +{
>> + struct cdnsp_request *preq;
>> + struct cdnsp_device *pdev;
>> + struct cdnsp_ep *pep;
>> + unsigned long flags;
>> + int ret;
>> +
>> + if (!request || !ep)
>> + return -EINVAL;
>> +
>> + pep = to_cdnsp_ep(ep);
>> + pdev = pep->pdev;
>> +
>> + if (!(pep->ep_state & EP_ENABLED)) {
>> + dev_err(pdev->dev, "%s: can't queue to disabled endpoint\n",
>> + pep->name);
>> + return -EINVAL;
>> + }
>> +
>> + preq = to_cdnsp_request(request);
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + ret = cdnsp_ep_enqueue(pep, preq);
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return ret;
>> +}
>> +
>> +static int cdnsp_gadget_ep_dequeue(struct usb_ep *ep,
>> + struct usb_request *request)
>> +{
>> + struct cdnsp_ep *pep = to_cdnsp_ep(ep);
>> + struct cdnsp_device *pdev = pep->pdev;
>> + unsigned long flags;
>> + int ret;
>> +
>> + if (!pep->endpoint.desc) {
>> + dev_err(pdev->dev,
>> + "%s: can't dequeue to disabled endpoint\n",
>> + pep->name);
>> + return -ESHUTDOWN;
>> + }
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + ret = cdnsp_ep_dequeue(pep, to_cdnsp_request(request));
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return ret;
>> +}
>> +
>> +static int cdnsp_gadget_ep_set_halt(struct usb_ep *ep, int value)
>> +{
>> + struct cdnsp_ep *pep = to_cdnsp_ep(ep);
>> + struct cdnsp_device *pdev = pep->pdev;
>> + struct cdnsp_request *preq;
>> + unsigned long flags = 0;
>> + int ret;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> +
>> + preq = next_request(&pep->pending_list);
>> + if (value) {
>> + if (preq) {
>> + ret = -EAGAIN;
>> + goto done;
>> + }
>> + }
>> +
>> + ret = cdnsp_halt_endpoint(pdev, pep, value);
>> +
>> +done:
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> + return ret;
>> +}
>> +
>> +static int cdnsp_gadget_ep_set_wedge(struct usb_ep *ep)
>> +{
>> + struct cdnsp_ep *pep = to_cdnsp_ep(ep);
>> + struct cdnsp_device *pdev = pep->pdev;
>> + unsigned long flags = 0;
>> + int ret;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + pep->ep_state |= EP_WEDGE;
>> + ret = cdnsp_halt_endpoint(pdev, pep, 1);
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return ret;
>> +}
>> +
>> +static const struct usb_ep_ops cdnsp_gadget_ep0_ops = {
>> + .enable = cdnsp_gadget_ep_enable,
>> + .disable = cdnsp_gadget_ep_disable,
>> + .alloc_request = cdnsp_gadget_ep_alloc_request,
>> + .free_request = cdnsp_gadget_ep_free_request,
>> + .queue = cdnsp_gadget_ep_queue,
>> + .dequeue = cdnsp_gadget_ep_dequeue,
>> + .set_halt = cdnsp_gadget_ep_set_halt,
>> + .set_wedge = cdnsp_gadget_ep_set_wedge,
>> +};
>> +
>> +static const struct usb_ep_ops cdnsp_gadget_ep_ops = {
>> + .enable = cdnsp_gadget_ep_enable,
>> + .disable = cdnsp_gadget_ep_disable,
>> + .alloc_request = cdnsp_gadget_ep_alloc_request,
>> + .free_request = cdnsp_gadget_ep_free_request,
>> + .queue = cdnsp_gadget_ep_queue,
>> + .dequeue = cdnsp_gadget_ep_dequeue,
>> + .set_halt = cdnsp_gadget_ep_set_halt,
>> + .set_wedge = cdnsp_gadget_ep_set_wedge,
>> +};
>> +
>> +void cdnsp_gadget_giveback(struct cdnsp_ep *pep,
>> + struct cdnsp_request *preq,
>> + int status)
>> +{
>> + struct cdnsp_device *pdev = pep->pdev;
>> +
>> + list_del(&preq->list);
>> +
>> + if (preq->request.status == -EINPROGRESS)
>> + preq->request.status = status;
>> +
>> + usb_gadget_unmap_request_by_dev(pdev->dev, &preq->request,
>> + preq->direction);
>> +
>> + if (preq != &pdev->ep0_preq) {
>> + spin_unlock(&pdev->lock);
>> + usb_gadget_giveback_request(&pep->endpoint, &preq->request);
>> + spin_lock(&pdev->lock);
>> + }
>> +}
>> +
>> +static struct usb_endpoint_descriptor cdnsp_gadget_ep0_desc = {
>> + .bLength = USB_DT_ENDPOINT_SIZE,
>> + .bDescriptorType = USB_DT_ENDPOINT,
>> + .bmAttributes = USB_ENDPOINT_XFER_CONTROL,
>> +};
>> +
>> +static int cdnsp_run(struct cdnsp_device *pdev,
>> + enum usb_device_speed speed)
>> +{
>> + u32 fs_speed = 0;
>> + u64 temp_64;
>> + u32 temp;
>> + int ret;
>> +
>> + temp_64 = cdnsp_read_64(pdev, &pdev->ir_set->erst_dequeue);
>> + temp_64 &= ~ERST_PTR_MASK;
>> + temp = readl(&pdev->ir_set->irq_control);
>> + temp &= ~IMOD_INTERVAL_MASK;
>> + temp |= ((IMOD_DEFAULT_INTERVAL / 250) & IMOD_INTERVAL_MASK);
>> + writel(temp, &pdev->ir_set->irq_control);
>> +
>> + temp = readl(&pdev->port3x_regs->mode_addr);
>> +
>> + switch (speed) {
>> + case USB_SPEED_SUPER_PLUS:
>> + temp |= CFG_3XPORT_SSP_SUPPORT;
>> + break;
>> + case USB_SPEED_SUPER:
>> + temp &= ~CFG_3XPORT_SSP_SUPPORT;
>> + break;
>> + case USB_SPEED_HIGH:
>> + break;
>> + case USB_SPEED_FULL:
>> + fs_speed = PORT_REG6_FORCE_FS;
>> + break;
>> + default:
>> + dev_err(pdev->dev, "invalid maximum_speed parameter %d\n",
>> + speed);
>> + fallthrough;
>> + case USB_SPEED_UNKNOWN:
>> + /* Default to superspeed. */
>> + speed = USB_SPEED_SUPER;
>> + break;
>> + }
>> +
>> + if (speed >= USB_SPEED_SUPER) {
>> + writel(temp, &pdev->port3x_regs->mode_addr);
>> + cdnsp_set_link_state(pdev, &pdev->usb3_port.regs->portsc,
>> + XDEV_RXDETECT);
>> + } else {
>> + cdnsp_disable_port(pdev, &pdev->usb3_port.regs->portsc);
>> + }
>> +
>> + cdnsp_set_link_state(pdev, &pdev->usb2_port.regs->portsc,
>> + XDEV_RXDETECT);
>> +
>> + cdnsp_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(512);
>> +
>> + writel(PORT_REG6_L1_L0_HW_EN | fs_speed, &pdev->port20_regs->port_reg6);
>> +
>> + ret = cdnsp_start(pdev);
>> + if (ret) {
>> + ret = -ENODEV;
>> + goto err;
>> + }
>> +
>> + temp = readl(&pdev->op_regs->command);
>> + temp |= (CMD_INTE);
>> + writel(temp, &pdev->op_regs->command);
>> +
>> + temp = readl(&pdev->ir_set->irq_pending);
>> + writel(IMAN_IE_SET(temp), &pdev->ir_set->irq_pending);
>> +
>> + return 0;
>> +err:
>> + cdnsp_halt(pdev);
>> + return ret;
>> +}
>> +
>> +static int cdnsp_gadget_udc_start(struct usb_gadget *g,
>> + struct usb_gadget_driver *driver)
>> +{
>> + enum usb_device_speed max_speed = driver->max_speed;
>> + struct cdnsp_device *pdev = gadget_to_cdnsp(g);
>> + unsigned long flags;
>> + int ret;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + pdev->gadget_driver = driver;
>> +
>> + /* limit speed if necessary */
>> + max_speed = min(driver->max_speed, g->max_speed);
>> + ret = cdnsp_run(pdev, max_speed);
>> +
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * Update Event Ring Dequeue Pointer:
>> + * - When all events have finished
>> + * - To avoid "Event Ring Full Error" condition
>> + */
>> +void cdnsp_update_erst_dequeue(struct cdnsp_device *pdev,
>> + union cdnsp_trb *event_ring_deq,
>> + u8 clear_ehb)
>> +{
>> + u64 temp_64;
>> + dma_addr_t deq;
>> +
>> + temp_64 = cdnsp_read_64(pdev, &pdev->ir_set->erst_dequeue);
>> +
>> + /* If necessary, update the HW's version of the event ring deq ptr. */
>> + if (event_ring_deq != pdev->event_ring->dequeue) {
>> + deq = cdnsp_trb_virt_to_dma(pdev->event_ring->deq_seg,
>> + pdev->event_ring->dequeue);
>> + temp_64 &= ERST_PTR_MASK;
>> + temp_64 |= ((u64)deq & (u64)~ERST_PTR_MASK);
>> + }
>> +
>> + /* Clear the event handler busy flag (RW1C). */
>> + if (clear_ehb)
>> + temp_64 |= ERST_EHB;
>> + else
>> + temp_64 &= ~ERST_EHB;
>> +
>> + cdnsp_write_64(pdev, temp_64, &pdev->ir_set->erst_dequeue);
>> +}
>> +
>> +static void cdnsp_clear_cmd_ring(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_segment *seg;
>> + u64 val_64;
>> + int i;
>> +
>> + cdnsp_initialize_ring_info(pdev->cmd_ring);
>> +
>> + seg = pdev->cmd_ring->first_seg;
>> + for (i = 0; i < pdev->cmd_ring->num_segs; i++) {
>> + memset(seg->trbs, 0,
>> + sizeof(union cdnsp_trb) * (TRBS_PER_SEGMENT - 1));
>> + seg = seg->next;
>> + }
>> +
>> + /* Set the address in the Command Ring Control register. */
>> + val_64 = cdnsp_read_64(pdev, &pdev->op_regs->cmd_ring);
>> + val_64 = (val_64 & (u64)CMD_RING_RSVD_BITS) |
>> + (pdev->cmd_ring->first_seg->dma & (u64)~CMD_RING_RSVD_BITS) |
>> + pdev->cmd_ring->cycle_state;
>> + cdnsp_write_64(pdev, val_64, &pdev->op_regs->cmd_ring);
>> +}
>> +
>> +static void cdnsp_consume_all_events(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_segment *event_deq_seg;
>> + union cdnsp_trb *event_ring_deq;
>> + union cdnsp_trb *event;
>> + u32 cycle_bit;
>> +
>> + event_ring_deq = pdev->event_ring->dequeue;
>> + event_deq_seg = pdev->event_ring->deq_seg;
>> + event = pdev->event_ring->dequeue;
>> +
>> + /* Update ring dequeue pointer. */
>> + while (1) {
>> + cycle_bit = (le32_to_cpu(event->event_cmd.flags) & TRB_CYCLE);
>> +
>> + /* Does the controller or driver own the TRB? */
>> + if (cycle_bit != pdev->event_ring->cycle_state)
>> + break;
>> +
>> + cdnsp_inc_deq(pdev, pdev->event_ring);
>> +
>> + if (!cdnsp_last_trb_on_seg(event_deq_seg, event)) {
>> + event++;
>> + continue;
>> + }
>> +
>> + if (cdnsp_last_trb_on_ring(pdev->event_ring, event_deq_seg,
>> + event))
>> + cycle_bit ^= 1;
>> +
>> + event_deq_seg = event_deq_seg->next;
>> + event = event_deq_seg->trbs;
>> + }
>> +
>> + cdnsp_update_erst_dequeue(pdev, event_ring_deq, 1);
>> +}
>> +
>> +static void cdnsp_stop(struct cdnsp_device *pdev)
>> +{
>> + u32 temp;
>> +
>> + cdnsp_cmd_flush_ep(pdev, &pdev->eps[0]);
>> +
>> + /* Remove internally queued request for ep0. */
>> + if (!list_empty(&pdev->eps[0].pending_list)) {
>> + struct cdnsp_request *req;
>> +
>> + req = next_request(&pdev->eps[0].pending_list);
>> + if (req == &pdev->ep0_preq)
>> + cdnsp_ep_dequeue(&pdev->eps[0], req);
>> + }
>> +
>> + cdnsp_disable_port(pdev, &pdev->usb2_port.regs->portsc);
>> + cdnsp_disable_port(pdev, &pdev->usb3_port.regs->portsc);
>> + cdnsp_disable_slot(pdev);
>> + cdnsp_halt(pdev);
>> +
>> + temp = readl(&pdev->op_regs->status);
>> + writel((temp & ~0x1fff) | STS_EINT, &pdev->op_regs->status);
>> + temp = readl(&pdev->ir_set->irq_pending);
>> + writel(IMAN_IE_CLEAR(temp), &pdev->ir_set->irq_pending);
>> +
>> + cdnsp_clear_port_change_bit(pdev, &pdev->usb2_port.regs->portsc);
>> + cdnsp_clear_port_change_bit(pdev, &pdev->usb3_port.regs->portsc);
>> +
>> + /*Clear interrupt line */
>> + temp = readl(&pdev->ir_set->irq_pending);
>> + temp |= IMAN_IP;
>> + writel(temp, &pdev->ir_set->irq_pending);
>> +
>> + cdnsp_consume_all_events(pdev);
>> + cdnsp_clear_cmd_ring(pdev);
>> +}
>> +
>> +/*
>> + * Stop controller.
>> + * This function is called by the gadget core when the driver is removed.
>> + * Disable slot, disable IRQs, and quiesce the controller.
>> + */
>> +static int cdnsp_gadget_udc_stop(struct usb_gadget *g)
>> +{
>> + struct cdnsp_device *pdev = gadget_to_cdnsp(g);
>> + unsigned long flags;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + cdnsp_stop(pdev);
>> + pdev->gadget_driver = NULL;
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_gadget_get_frame(struct usb_gadget *g)
>> +{
>> + struct cdnsp_device *pdev = gadget_to_cdnsp(g);
>> +
>> + return cdnsp_get_frame(pdev);
>> +}
>> +
>> +static void __cdnsp_gadget_wakeup(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_port_regs __iomem *port_regs;
>> + u32 portpm, portsc;
>> +
>> + port_regs = pdev->active_port->regs;
>> + portsc = readl(&port_regs->portsc) & PORT_PLS_MASK;
>> +
>> + /* Remote wakeup feature is not enabled by host. */
>> + if (pdev->gadget.speed < USB_SPEED_SUPER && portsc == XDEV_U2) {
>> + portpm = readl(&port_regs->portpmsc);
>> +
>> + if (!(portpm & PORT_RWE))
>> + return;
>> + }
>> +
>> + if (portsc == XDEV_U3 && !pdev->may_wakeup)
>> + return;
>> +
>> + cdnsp_set_link_state(pdev, &port_regs->portsc, XDEV_U0);
>> +
>> + pdev->cdnsp_state |= CDNSP_WAKEUP_PENDING;
>> +}
>> +
>> +static int cdnsp_gadget_wakeup(struct usb_gadget *g)
>> +{
>> + struct cdnsp_device *pdev = gadget_to_cdnsp(g);
>> + unsigned long flags;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + __cdnsp_gadget_wakeup(pdev);
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_gadget_set_selfpowered(struct usb_gadget *g,
>> + int is_selfpowered)
>> +{
>> + struct cdnsp_device *pdev = gadget_to_cdnsp(g);
>> + unsigned long flags;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + g->is_selfpowered = !!is_selfpowered;
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_gadget_pullup(struct usb_gadget *gadget, int is_on)
>> +{
>> + struct cdnsp_device *pdev = gadget_to_cdnsp(gadget);
>> + struct cdns *cdns = dev_get_drvdata(pdev->dev);
>> +
>> + if (!is_on) {
>> + cdnsp_reset_device(pdev);
>> + cdns_clear_vbus(cdns);
>> + } else {
>> + cdns_set_vbus(cdns);
>> + }
>> + return 0;
>> +}
>> +
>> +const struct usb_gadget_ops cdnsp_gadget_ops = {
>> + .get_frame = cdnsp_gadget_get_frame,
>> + .wakeup = cdnsp_gadget_wakeup,
>> + .set_selfpowered = cdnsp_gadget_set_selfpowered,
>> + .pullup = cdnsp_gadget_pullup,
>> + .udc_start = cdnsp_gadget_udc_start,
>> + .udc_stop = cdnsp_gadget_udc_stop,
>> +};
>> +
>> +static void cdnsp_get_ep_buffering(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep)
>> +{
>> + void __iomem *reg = &pdev->cap_regs->hc_capbase;
>> + int endpoints;
>> +
>> + reg += cdnsp_find_next_ext_cap(reg, 0, XBUF_CAP_ID);
>> +
>> + if (!pep->direction) {
>> + pep->buffering = readl(reg + XBUF_RX_TAG_MASK_0_OFFSET);
>> + pep->buffering_period = readl(reg + XBUF_RX_TAG_MASK_1_OFFSET);
>> + pep->buffering = (pep->buffering + 1) / 2;
>> + pep->buffering_period = (pep->buffering_period + 1) / 2;
>> + return;
>> + }
>> +
>> + endpoints = HCS_ENDPOINTS(readl(&pdev->hcs_params1)) / 2;
>> +
>> + /* Set to XBUF_TX_TAG_MASK_0 register. */
>> + reg += XBUF_TX_CMD_OFFSET + (endpoints * 2 + 2) * sizeof(u32);
>> + /* Set reg to XBUF_TX_TAG_MASK_N related with this endpoint. */
>> + reg += pep->number * sizeof(u32) * 2;
>> +
>> + pep->buffering = (readl(reg) + 1) / 2;
>> + pep->buffering_period = pep->buffering;
>> +}
>> +
>> +static int cdnsp_gadget_init_endpoints(struct cdnsp_device *pdev)
>> +{
>> + int max_streams = HCC_MAX_PSA(pdev->hcc_params);
>> + struct cdnsp_ep *pep;
>> + int i;
>> +
>> + INIT_LIST_HEAD(&pdev->gadget.ep_list);
>> +
>> + if (max_streams < STREAM_LOG_STREAMS) {
>> + dev_err(pdev->dev, "Stream size %d not supported\n",
>> + max_streams);
>> + return -EINVAL;
>> + }
>> +
>> + max_streams = STREAM_LOG_STREAMS;
>> +
>> + for (i = 0; i < CDNSP_ENDPOINTS_NUM; i++) {
>> + bool direction = !(i & 1); /* Start from OUT endpoint. */
>> + u8 epnum = ((i + 1) >> 1);
>> +
>> + if (!CDNSP_IF_EP_EXIST(pdev, epnum, direction))
>> + continue;
>> +
>> + pep = &pdev->eps[i];
>> + pep->pdev = pdev;
>> + pep->number = epnum;
>> + pep->direction = direction; /* 0 for OUT, 1 for IN. */
>> +
>> + /*
>> + * Ep0 is bidirectional, so ep0in and ep0out are represented by
>> + * pdev->eps[0]
>> + */
>> + if (epnum == 0) {
>> + snprintf(pep->name, sizeof(pep->name), "ep%d%s",
>> + epnum, "BiDir");
>> +
>> + pep->idx = 0;
>> + usb_ep_set_maxpacket_limit(&pep->endpoint, 512);
>> + pep->endpoint.maxburst = 1;
>> + pep->endpoint.ops = &cdnsp_gadget_ep0_ops;
>> + pep->endpoint.desc = &cdnsp_gadget_ep0_desc;
>> + pep->endpoint.comp_desc = NULL;
>> + pep->endpoint.caps.type_control = true;
>> + pep->endpoint.caps.dir_in = true;
>> + pep->endpoint.caps.dir_out = true;
>> +
>> + pdev->ep0_preq.epnum = pep->number;
>> + pdev->ep0_preq.pep = pep;
>> + pdev->gadget.ep0 = &pep->endpoint;
>> + } else {
>> + snprintf(pep->name, sizeof(pep->name), "ep%d%s",
>> + epnum, (pep->direction) ? "in" : "out");
>there is two blank space after "in", please use checkpatch.pl with
>--strict
I always use checkpsatch.pl with --strict option. It didn't complain
for this case.
<snip>
Thanks,
Pawel
>>
Powered by blists - more mailing lists