[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <6bc40a50-8c21-4642-ad9e-e92f756aac25@www.fastmail.com>
Date: Thu, 01 Oct 2020 10:06:20 +0930
From: "Andrew Jeffery" <andrew@...id.au>
To: "Billy Tsai" <billy_tsai@...eedtech.com>,
"Rob Herring" <robh+dt@...nel.org>,
"Joel Stanley" <joel@....id.au>, devicetree@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org,
linux-aspeed@...ts.ozlabs.org, linux-kernel@...r.kernel.org
Cc: BMC-SW@...eedtech.com
Subject: Re: [PATCH] ARM: dts: aspeed-g6: Add sgpiom/sgpios node
Hi Billy,
On Wed, 30 Sep 2020, at 14:41, Billy Tsai wrote:
> This commit add two sgpiom and two sgpios node into aspeed-g6.dtsi
> and change the register range of gpio0 to fix the hardware design.
>
> Signed-off-by: Billy Tsai <billy_tsai@...eedtech.com>
> ---
> arch/arm/boot/dts/aspeed-g6.dtsi | 51 +++++++++++++++++++++++++++++++-
> 1 file changed, 50 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/aspeed-g6.dtsi b/arch/arm/boot/dts/aspeed-g6.dtsi
> index 97ca743363d7..00237daec2a1 100644
> --- a/arch/arm/boot/dts/aspeed-g6.dtsi
> +++ b/arch/arm/boot/dts/aspeed-g6.dtsi
> @@ -357,7 +357,7 @@
> #gpio-cells = <2>;
> gpio-controller;
> compatible = "aspeed,ast2600-gpio";
> - reg = <0x1e780000 0x800>;
> + reg = <0x1e780000 0x500>;
> interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
> gpio-ranges = <&pinctrl 0 0 208>;
> ngpios = <208>;
> @@ -365,6 +365,55 @@
> interrupt-controller;
> #interrupt-cells = <2>;
> };
> + sgpiom0: sgpiom@...80500 {
> + #gpio-cells = <2>;
> + gpio-controller;
> + compatible = "aspeed,ast2600-sgpiom";
> + reg = <0x1e780500 0x100>;
> + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
> + ngpios = <128>;
> + clocks = <&syscon ASPEED_CLK_APB2>;
> + interrupt-controller;
> + bus-frequency = <12000000>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_sgpm1_default>;
> + status = "disabled";
> + };
> +
> + sgpiom1: sgpiom@...80600 {
> + #gpio-cells = <2>;
> + gpio-controller;
> + compatible = "aspeed,ast2600-sgpiom";
> + reg = <0x1e780600 0x100>;
> + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
> + ngpios = <80>;
> + clocks = <&syscon ASPEED_CLK_APB2>;
> + interrupt-controller;
> + bus-frequency = <12000000>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_sgpm2_default>;
Have you tried building this on top of upstream? Because neither sgpm2 nor
sgps2 are supported by the pinctrl driver. If you have patches that implement
both mux configurations, can you post them too?
Andrew
Powered by blists - more mailing lists