[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20201001151901.GB14276@kozik-lap>
Date: Thu, 1 Oct 2020 17:19:01 +0200
From: Krzysztof Kozlowski <krzk@...nel.org>
To: Schrempf Frieder <frieder.schrempf@...tron.de>
Cc: Andreas Kemnade <andreas@...nade.info>,
"Angus Ainslie (Purism)" <angus@...ea.ca>,
Anson Huang <Anson.Huang@....com>,
Fabio Estevam <festevam@...il.com>,
Li Yang <leoyang.li@....com>, Michael Walle <michael@...le.cc>,
NXP Linux Team <linux-imx@....com>,
Pengutronix Kernel Team <kernel@...gutronix.de>,
Rabeeh Khoury <rabeeh@...id-run.com>,
Robert Jones <rjones@...eworks.com>,
Rob Herring <robh@...nel.org>,
Sascha Hauer <s.hauer@...gutronix.de>,
Sébastien Szymanski
<sebastien.szymanski@...adeus.com>,
Shawn Guo <shawnguo@...nel.org>,
Stefan Riedmueller <s.riedmueller@...tec.de>,
Stoica Cosmin-Stefan <cosmin.stoica@....com>,
devicetree@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
linux-kernel@...r.kernel.org,
Marcel Ziswiler <marcel.ziswiler@...adex.com>
Subject: Re: [PATCH v5 1/2] arm64: dts: Add the Kontron i.MX8M Mini SoMs and
baseboards
On Thu, Oct 01, 2020 at 05:13:37PM +0200, Schrempf Frieder wrote:
> From: Frieder Schrempf <frieder.schrempf@...tron.de>
>
> Kontron Electronics GmbH offers small and powerful SoMs based on the
> i.MX8M Mini SoC including PMIC, LPDDR4-RAM, eMMC and SPI NOR.
>
> The matching baseboards have the same form factor and similar interfaces
> as the other boards from the Kontron "Board-Line" family, including
> SD card, 1G Ethernet, 100M Ethernet, USB Host/OTG, digital IOs, RS232,
> RS485, CAN, LVDS or HDMI, RTC and much more.
>
> Signed-off-by: Frieder Schrempf <frieder.schrempf@...tron.de>
> ---
> Changes for v5:
> * Add Makefile entry to build dtb
>
> Changes for v4:
> * Remove one more needless status property
> * Use local-mac-address instead of mac-address
> * Add missing pinctrl-names in PMIC node
> * Fix interrupt flags in PMIC node
> * Use lowercase regulator names
> * Enable pullup for PMIC IRQ line
> * Fix pinctrl grp names to match schema
>
> Changes for v3:
> * Remove needless status properties
> * Remove needless regulator properties for reg_vdd_5v
> * Use proper PHY reset properties in PHY node
> * Use phy-connection-type instead of phy-mode
> * Adjust PMIC node name and label
> * Add over-current-active-low to usbotg1 node
> * Remove redundant bus-width property from usdhc2 node
> * Remove needless regulator-compatible from reg_vdd_snvs
> * Set minimum voltage to 85mV for reg_vdd_snvs
>
> Changes for v2:
> * Make the licensing less strict (GPL-2.0+ OR MIT)
> * Merge the SoM and baseboard DTs for N8010 and N8011 into one as
> they only differ in DDR and eMMC size.
> * Change compatibles and model strings to "n810x" and "N8010X".
> * Only use a common memory node that will be updated by the
> bootloader reflecting the detected DDR size.
> * Improve naming for 16MHz CAN fixed oscillator and set
> "clock-output-names".
> * Consistently use "reg_" prefix for regulators.
> * Remove "userspi" node.
> * Slightly improve commit message.
> ---
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../dts/freescale/imx8mm-kontron-n801x-s.dts | 322 ++++++++++++++++++
> .../freescale/imx8mm-kontron-n801x-som.dtsi | 294 ++++++++++++++++
> 3 files changed, 617 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
Reviewed-by: Krzysztof Kozlowski <krzk@...nel.org>
Best regards,
Krzysztof
Powered by blists - more mailing lists