linux-kernel - Re: [PATCH v2 3/4] ARM: dts: exynos: Add Ethernet to Artik 5 board

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Date:   Sat, 3 Oct 2020 12:13:54 +0200
From:   Krzysztof Kozlowski <krzk@...nel.org>
To:     Łukasz Stelmach <l.stelmach@...sung.com>
Cc:     "David S. Miller" <davem@...emloft.net>,
        Jakub Kicinski <kuba@...nel.org>,
        Kukjin Kim <kgene@...nel.org>,
        Rob Herring <robh+dt@...nel.org>,
        Russell King <linux@...linux.org.uk>,
        Andrew Lunn <andrew@...n.ch>, jim.cromie@...il.com,
        linux-arm-kernel@...ts.infradead.org,
        "linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
        "linux-samsung-soc@...r.kernel.org" 
        <linux-samsung-soc@...r.kernel.org>, netdev@...r.kernel.org,
        devicetree@...r.kernel.org,
        Bartłomiej Żolnierkiewicz 
        <b.zolnierkie@...sung.com>,
        Marek Szyprowski <m.szyprowski@...sung.com>
Subject: Re: [PATCH v2 3/4] ARM: dts: exynos: Add Ethernet to Artik 5 board

On Fri, 2 Oct 2020 at 21:22, Łukasz Stelmach <l.stelmach@...sung.com> wrote:
>
> Add node for ax88796c ethernet chip.
>
> Signed-off-by: Łukasz Stelmach <l.stelmach@...sung.com>
> ---
>  arch/arm/boot/dts/exynos3250-artik5-eval.dts | 21 ++++++++++++++++++++
>  1 file changed, 21 insertions(+)
>
> diff --git a/arch/arm/boot/dts/exynos3250-artik5-eval.dts b/arch/arm/boot/dts/exynos3250-artik5-eval.dts
> index 20446a846a98..7f115c348a2a 100644
> --- a/arch/arm/boot/dts/exynos3250-artik5-eval.dts
> +++ b/arch/arm/boot/dts/exynos3250-artik5-eval.dts
> @@ -37,3 +37,24 @@ &mshc_2 {
>  &serial_2 {
>         status = "okay";
>  };
> +
> +&spi_0 {
> +       status = "okay";
> +       cs-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>, <0>;
> +
> +       assigned-clocks        = <&cmu CLK_MOUT_MPLL>, <&cmu CLK_DIV_MPLL_PRE>, <&cmu CLK_MOUT_SPI0>,    <&cmu CLK_DIV_SPI0>,  <&cmu CLK_DIV_SPI0_PRE>, <&cmu CLK_SCLK_SPI0>;

No spaces before or after '='.

> +       assigned-clock-parents = <&cmu CLK_FOUT_MPLL>, <&cmu CLK_MOUT_MPLL>,    <&cmu CLK_DIV_MPLL_PRE>, <&cmu CLK_MOUT_SPI0>, <&cmu CLK_DIV_SPI0>,     <&cmu CLK_DIV_SPI0_PRE>;

This line is still too long. Please wrap it at 80. Checkpatch should
complain about it... so it seems you did not run it. Please fix all
checkpatch issues.

> +
> +       ax88796c@0 {
> +               compatible = "asix,ax88796c";
> +               local-mac-address = [00 00 00 00 00 00]; /* Filled in by a boot-loader */
> +               interrupt-parent = <&gpx2>;
> +               interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> +               spi-max-frequency = <40000000>;
> +               reg = <0x0>;

Put reg after compatible.

Best regards,
Krzysztof