[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20201015135317.5jsrrqmwmdz4lnzm@mobilestation>
Date: Thu, 15 Oct 2020 16:53:17 +0300
From: Serge Semin <Sergey.Semin@...kalelectronics.ru>
To: Felipe Balbi <balbi@...nel.org>
CC: Serge Semin <fancer.lancer@...il.com>,
Mathias Nyman <mathias.nyman@...el.com>,
Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
Rob Herring <robh+dt@...nel.org>,
Jason Cooper <jason@...edaemon.net>,
Andrew Lunn <andrew@...n.ch>,
Gregory Clement <gregory.clement@...tlin.com>,
Sebastian Hesselbarth <sebastian.hesselbarth@...il.com>,
Kukjin Kim <kgene@...nel.org>,
Krzysztof Kozlowski <krzk@...nel.org>,
Santosh Shilimkar <ssantosh@...nel.org>,
Shawn Guo <shawnguo@...nel.org>, Li Yang <leoyang.li@....com>,
BenoƮt Cousson <bcousson@...libre.com>,
Tony Lindgren <tony@...mide.com>,
Patrice Chotard <patrice.chotard@...com>,
Maxime Ripard <mripard@...nel.org>,
Chen-Yu Tsai <wens@...e.org>, Wei Xu <xuwei5@...ilicon.com>,
Andy Gross <agross@...nel.org>,
Bjorn Andersson <bjorn.andersson@...aro.org>,
Alexey Malahov <Alexey.Malahov@...kalelectronics.ru>,
Pavel Parkhomenko <Pavel.Parkhomenko@...kalelectronics.ru>,
Manu Gautam <mgautam@...eaurora.org>,
Roger Quadros <rogerq@...com>,
Lad Prabhakar <prabhakar.mahadev-lad.rj@...renesas.com>,
Yoshihiro Shimoda <yoshihiro.shimoda.uh@...esas.com>,
Neil Armstrong <narmstrong@...libre.com>,
Kevin Hilman <khilman@...libre.com>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-snps-arc@...ts.infradead.org>, <linux-mips@...r.kernel.org>,
<linuxppc-dev@...ts.ozlabs.org>, <linux-usb@...r.kernel.org>,
<devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
<linux-samsung-soc@...r.kernel.org>, <linux-omap@...r.kernel.org>,
<linux-arm-msm@...r.kernel.org>
Subject: Re: [PATCH 20/20] arch: dts: Fix DWC USB3 DT nodes name
On Thu, Oct 15, 2020 at 01:15:37PM +0300, Felipe Balbi wrote:
> Serge Semin <Sergey.Semin@...kalelectronics.ru> writes:
>
> > On Wed, Oct 14, 2020 at 05:09:37PM +0300, Felipe Balbi wrote:
> >>
> >> Hi Serge,
> >>
> >> Serge Semin <Sergey.Semin@...kalelectronics.ru> writes:
> >> > In accordance with the DWC USB3 bindings the corresponding node name is
> >> > suppose to comply with Generic USB HCD DT schema, which requires the USB
> >>
> >
> >> DWC3 is not a simple HDC, though.
> >
> > Yeah, strictly speaking it is equipped with a lot of vendor-specific stuff,
> > which are tuned by the DWC USB3 driver in the kernel. But after that the
> > controller is registered as xhci-hcd device so it's serviced by the xHCI driver,
>
> in Dual-role or host-only builds, that's correct. We can also have
> peripheral-only builds (both SW or HW versions) which means xhci isn't
> even in the picture.
Hm, good point. In that case perhaps we'll need to apply the xHCI DT schema
conditionally. Like this:
- allOf:
- - $ref: usb-xhci.yaml#
+ allOf:
+ - if:
+ properties:
+ dr_mode:
+ const: peripheral
+ then:
+ $ref: usb-hcd.yaml#
+ else:
+ $ref: usb-xhci.yaml#
Note, we need to have the peripheral device being compatible with the
usb-hcd.yaml schema to support the maximum-speed, dr_mode properties and to
comply with the USB node naming constraint.
-Sergey
>
> --
> balbi
Powered by blists - more mailing lists