[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20201031211251.GA6511@Red>
Date: Sat, 31 Oct 2020 22:12:51 +0100
From: Corentin Labbe <clabbe.montjoie@...il.com>
To: Jernej Skrabec <jernej.skrabec@...l.net>
Cc: mripard@...nel.org, wens@...e.org, robh+dt@...nel.org,
devicetree@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
linux-kernel@...r.kernel.org, linux-sunxi@...glegroups.com
Subject: Re: [linux-sunxi] [PATCH v2] arm64: dts: allwinner: h6: PineH64
model B: Add wifi
On Fri, Oct 30, 2020 at 06:25:30PM +0100, Jernej Skrabec wrote:
> PineH64 model B contains RTL8723CS wifi+bt combo module.
>
> Since bluetooth support is not yet squared away, only wifi is enabled
> for now.
>
> Acked-by: Chen-Yu Tsai <wens@...e.org>
> Signed-off-by: Jernej Skrabec <jernej.skrabec@...l.net>
> ---
> Changes from v1:
> - added Chen-Yu tag
> - added vqmmc-supply
>
> .../dts/allwinner/sun50i-h6-pine-h64-model-b.dts | 15 +++++++++++++++
> 1 file changed, 15 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts
> index f4c8966a6497..7fea1e4e2d49 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts
> @@ -10,6 +10,12 @@ / {
> compatible = "pine64,pine-h64-model-b", "allwinner,sun50i-h6";
>
> /delete-node/ reg_gmac_3v3;
> +
> + wifi_pwrseq: wifi_pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
> + post-power-on-delay-ms = <200>;
> + };
> };
>
> &hdmi_connector {
> @@ -19,3 +25,12 @@ &hdmi_connector {
> &emac {
> phy-supply = <®_aldo2>;
> };
> +
> +&mmc1 {
> + vmmc-supply = <®_cldo3>;
> + vqmmc-supply = <®_aldo1>;
> + mmc-pwrseq = <&wifi_pwrseq>;
> + bus-width = <4>;
> + non-removable;
> + status = "okay";
> +};
> --
Hello
Tested-by: <clabbe.montjoie@...il.com>
RTL8723CS driver probe and related iwlist commands works. (like listing availlable channels)
But connecting to a wireless network was not successfully tested yet. (I need to set a test network).
Regards
Powered by blists - more mailing lists