| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20201104103938.1286-12-nsaenzjulienne@suse.de>
Date: Wed, 4 Nov 2020 11:39:37 +0100
From: Nicolas Saenz Julienne <nsaenzjulienne@...e.de>
To: u.kleine-koenig@...gutronix.de, linux-kernel@...r.kernel.org,
Thierry Reding <thierry.reding@...il.com>,
Lee Jones <lee.jones@...aro.org>
Cc: f.fainelli@...il.com, linux-pwm@...r.kernel.org,
bcm-kernel-feedback-list@...adcom.com,
linux-arm-kernel@...ts.infradead.org, devicetree@...r.kernel.org,
wahrenst@....net, linux-input@...r.kernel.org,
dmitry.torokhov@...il.com, gregkh@...uxfoundation.org,
devel@...verdev.osuosl.org, p.zabel@...gutronix.de,
linux-gpio@...r.kernel.org, linus.walleij@...aro.org,
linux-clk@...r.kernel.org, sboyd@...nel.org,
linux-rpi-kernel@...ts.infradead.org, bgolaszewski@...libre.com,
andy.shevchenko@...il.com,
Nicolas Saenz Julienne <nsaenzjulienne@...e.de>
Subject: [PATCH v3 11/11] pwm: Add Raspberry Pi Firmware based PWM bus
Adds support to control the PWM bus available in official Raspberry Pi
PoE HAT. Only RPi's co-processor has access to it, so commands have to
be sent through RPi's firmware mailbox interface.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@...e.de>
---
Changes since v2:
- Use devm_rpi_firmware_get()
- Rename driver
- Small cleanups as per Andy Shevchenko's comments
Changes since v1:
- Use default pwm bindings and get rid of xlate() function
- Correct spelling errors
- Correct apply() function
- Round values
- Fix divisions in arm32 mode
- Small cleanups
drivers/pwm/Kconfig | 9 ++
drivers/pwm/Makefile | 1 +
drivers/pwm/pwm-raspberrypi-poe.c | 216 ++++++++++++++++++++++++++++++
3 files changed, 226 insertions(+)
create mode 100644 drivers/pwm/pwm-raspberrypi-poe.c
diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
index 63be5362fd3a..ab31615f07fc 100644
--- a/drivers/pwm/Kconfig
+++ b/drivers/pwm/Kconfig
@@ -379,6 +379,15 @@ config PWM_PXA
To compile this driver as a module, choose M here: the module
will be called pwm-pxa.
+config PWM_RASPBERRYPI_POE
+ tristate "Raspberry Pi Firwmware PoE Hat PWM support"
+ # Make sure not 'y' when RASPBERRYPI_FIRMWARE is 'm'. This can only
+ # happen when COMPILE_TEST=y, hence the added !RASPBERRYPI_FIRMWARE.
+ depends on RASPBERRYPI_FIRMWARE || (COMPILE_TEST && !RASPBERRYPI_FIRMWARE)
+ help
+ Enable Raspberry Pi firmware controller PWM bus used to control the
+ official RPI PoE hat
+
config PWM_RCAR
tristate "Renesas R-Car PWM support"
depends on ARCH_RENESAS || COMPILE_TEST
diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
index cbdcd55d69ee..7ecbbbcb323a 100644
--- a/drivers/pwm/Makefile
+++ b/drivers/pwm/Makefile
@@ -35,6 +35,7 @@ obj-$(CONFIG_PWM_MXS) += pwm-mxs.o
obj-$(CONFIG_PWM_OMAP_DMTIMER) += pwm-omap-dmtimer.o
obj-$(CONFIG_PWM_PCA9685) += pwm-pca9685.o
obj-$(CONFIG_PWM_PXA) += pwm-pxa.o
+obj-$(CONFIG_PWM_RASPBERRYPI_POE) += pwm-raspberrypi-poe.o
obj-$(CONFIG_PWM_RCAR) += pwm-rcar.o
obj-$(CONFIG_PWM_RENESAS_TPU) += pwm-renesas-tpu.o
obj-$(CONFIG_PWM_ROCKCHIP) += pwm-rockchip.o
diff --git a/drivers/pwm/pwm-raspberrypi-poe.c b/drivers/pwm/pwm-raspberrypi-poe.c
new file mode 100644
index 000000000000..91cd826a36f3
--- /dev/null
+++ b/drivers/pwm/pwm-raspberrypi-poe.c
@@ -0,0 +1,216 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2020 Nicolas Saenz Julienne <nsaenzjulienne@...e.de>
+ * For more information on Raspberry Pi's PoE hat see:
+ * https://www.raspberrypi.org/products/poe-hat/
+ *
+ * Limitations:
+ * - No disable bit, so a disabled PWM is simulated by duty_cycle 0
+ * - Only normal polarity
+ * - Fixed 12.5 kHz period
+ *
+ * The current period is completed when HW is reconfigured.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pwm.h>
+
+#include <soc/bcm2835/raspberrypi-firmware.h>
+#include <dt-bindings/pwm/raspberrypi,firmware-pwm.h>
+
+#define RPI_PWM_MAX_DUTY 255
+#define RPI_PWM_PERIOD_NS 80000 /* 12.5 kHz */
+
+#define RPI_PWM_CUR_DUTY_REG 0x0
+#define RPI_PWM_DEF_DUTY_REG 0x1
+
+struct raspberrypi_pwm {
+ struct rpi_firmware *firmware;
+ struct pwm_chip chip;
+ unsigned int duty_cycle;
+};
+
+struct raspberrypi_pwm_prop {
+ __le32 reg;
+ __le32 val;
+ __le32 ret;
+} __packed;
+
+static inline struct raspberrypi_pwm *to_raspberrypi_pwm(struct pwm_chip *chip)
+{
+ return container_of(chip, struct raspberrypi_pwm, chip);
+}
+
+static int raspberrypi_pwm_set_property(struct rpi_firmware *firmware,
+ u32 reg, u32 val)
+{
+ struct raspberrypi_pwm_prop msg = {
+ .reg = cpu_to_le32(reg),
+ .val = cpu_to_le32(val),
+ };
+ int ret;
+
+ ret = rpi_firmware_property(firmware, RPI_FIRMWARE_SET_POE_HAT_VAL,
+ &msg, sizeof(msg));
+ if (ret)
+ return ret;
+ if (msg.ret)
+ return -EIO;
+
+ return 0;
+}
+
+static int raspberrypi_pwm_get_property(struct rpi_firmware *firmware,
+ u32 reg, u32 *val)
+{
+ struct raspberrypi_pwm_prop msg = {
+ .reg = reg
+ };
+ int ret;
+
+ ret = rpi_firmware_property(firmware, RPI_FIRMWARE_GET_POE_HAT_VAL,
+ &msg, sizeof(msg));
+ if (ret)
+ return ret;
+ if (msg.ret)
+ return -EIO;
+
+ *val = le32_to_cpu(msg.val);
+
+ return 0;
+}
+
+static void raspberrypi_pwm_get_state(struct pwm_chip *chip,
+ struct pwm_device *pwm,
+ struct pwm_state *state)
+{
+ struct raspberrypi_pwm *rpipwm = to_raspberrypi_pwm(chip);
+
+ state->period = RPI_PWM_PERIOD_NS;
+ state->duty_cycle = DIV_ROUND_CLOSEST(rpipwm->duty_cycle * RPI_PWM_PERIOD_NS,
+ RPI_PWM_MAX_DUTY);
+ state->enabled = !!(rpipwm->duty_cycle);
+ state->polarity = PWM_POLARITY_NORMAL;
+}
+
+static int raspberrypi_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
+ const struct pwm_state *state)
+{
+ struct raspberrypi_pwm *rpipwm = to_raspberrypi_pwm(chip);
+ unsigned int duty_cycle;
+ int ret;
+
+ if (state->period < RPI_PWM_PERIOD_NS ||
+ state->polarity != PWM_POLARITY_NORMAL)
+ return -EINVAL;
+
+ if (!state->enabled)
+ duty_cycle = 0;
+ else if (state->duty_cycle < RPI_PWM_PERIOD_NS)
+ duty_cycle = DIV_ROUND_CLOSEST_ULL(state->duty_cycle * RPI_PWM_MAX_DUTY,
+ RPI_PWM_PERIOD_NS);
+ else
+ duty_cycle = RPI_PWM_MAX_DUTY;
+
+ if (duty_cycle == rpipwm->duty_cycle)
+ return 0;
+
+ ret = raspberrypi_pwm_set_property(rpipwm->firmware, RPI_PWM_CUR_DUTY_REG,
+ duty_cycle);
+ if (ret) {
+ dev_err(chip->dev, "Failed to set duty cycle: %d\n", ret);
+ return ret;
+ }
+
+ /*
+ * This sets the default duty cycle after resetting the board, we
+ * updated it every time to mimic Raspberry Pi's downstream's driver
+ * behaviour.
+ */
+ ret = raspberrypi_pwm_set_property(rpipwm->firmware, RPI_PWM_DEF_DUTY_REG,
+ duty_cycle);
+ if (ret) {
+ dev_err(chip->dev, "Failed to set default duty cycle: %d\n", ret);
+ return ret;
+ }
+
+ rpipwm->duty_cycle = duty_cycle;
+
+ return 0;
+}
+
+static const struct pwm_ops raspberrypi_pwm_ops = {
+ .get_state = raspberrypi_pwm_get_state,
+ .apply = raspberrypi_pwm_apply,
+ .owner = THIS_MODULE,
+};
+
+static int raspberrypi_pwm_probe(struct platform_device *pdev)
+{
+ struct device_node *firmware_node;
+ struct device *dev = &pdev->dev;
+ struct rpi_firmware *firmware;
+ struct raspberrypi_pwm *rpipwm;
+ int ret;
+
+ firmware_node = of_get_parent(dev->of_node);
+ if (!firmware_node) {
+ dev_err(dev, "Missing firmware node\n");
+ return -ENOENT;
+ }
+
+ firmware = devm_rpi_firmware_get(&pdev->dev, firmware_node);
+ of_node_put(firmware_node);
+ if (!firmware)
+ return -EPROBE_DEFER;
+
+ rpipwm = devm_kzalloc(&pdev->dev, sizeof(*rpipwm), GFP_KERNEL);
+ if (!rpipwm)
+ return -ENOMEM;
+
+ rpipwm->firmware = firmware;
+ rpipwm->chip.dev = dev;
+ rpipwm->chip.ops = &raspberrypi_pwm_ops;
+ rpipwm->chip.base = -1;
+ rpipwm->chip.npwm = RASPBERRYPI_FIRMWARE_PWM_NUM;
+
+ platform_set_drvdata(pdev, rpipwm);
+
+ ret = raspberrypi_pwm_get_property(rpipwm->firmware, RPI_PWM_CUR_DUTY_REG,
+ &rpipwm->duty_cycle);
+ if (ret) {
+ dev_err(dev, "Failed to get duty cycle: %d\n", ret);
+ return ret;
+ }
+
+ return pwmchip_add(&rpipwm->chip);
+}
+
+static int raspberrypi_pwm_remove(struct platform_device *pdev)
+{
+ struct raspberrypi_pwm *rpipwm = platform_get_drvdata(pdev);
+
+ return pwmchip_remove(&rpipwm->chip);
+}
+
+static const struct of_device_id raspberrypi_pwm_of_match[] = {
+ { .compatible = "raspberrypi,firmware-pwm", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, raspberrypi_pwm_of_match);
+
+static struct platform_driver raspberrypi_pwm_driver = {
+ .driver = {
+ .name = "raspberrypi-pwm",
+ .of_match_table = raspberrypi_pwm_of_match,
+ },
+ .probe = raspberrypi_pwm_probe,
+ .remove = raspberrypi_pwm_remove,
+};
+module_platform_driver(raspberrypi_pwm_driver);
+
+MODULE_AUTHOR("Nicolas Saenz Julienne <nsaenzjulienne@...e.de>");
+MODULE_DESCRIPTION("Raspberry Pi Firwmare Based PWM Bus Driver");
+MODULE_LICENSE("GPL v2");
--
2.29.1
Powered by blists - more mailing lists