Message-ID: <CAAVeFuJ_rSN=JBi-2L2-v7eVonarGRzL5agTL-UW_WOD91D_tw@mail.gmail.com>
Date:   Thu, 5 Nov 2020 23:05:18 +0900
From:   Alexandre Courbot <gnurou@...il.com>
To:     Hans Verkuil <hverkuil-cisco@...all.nl>
Cc:     Mauro Carvalho Chehab <mchehab@...nel.org>,
        linux-media <linux-media@...r.kernel.org>,
        Linux Kernel Mailing List <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH] media: v4l2-mem2mem: always call poll_wait() on queues

On Thu, Nov 5, 2020 at 10:12 PM Hans Verkuil <hverkuil-cisco@...all.nl> wrote:
>
> On 05/11/2020 13:52, Alexandre Courbot wrote:
> > On Thu, Nov 5, 2020 at 9:36 PM Hans Verkuil <hverkuil-cisco@...all.nl> wrote:
> >>
> >> On 05/11/2020 13:21, Alexandre Courbot wrote:
> >>> On Tue, Nov 3, 2020 at 6:48 PM Hans Verkuil <hverkuil-cisco@...all.nl> wrote:
> >>>>
> >>>> On 03/11/2020 09:51, Alexandre Courbot wrote:
> >>>>> Hi Hans,
> >>>>>
> >>>>> On Sat, Oct 31, 2020 at 12:09 AM Hans Verkuil <hverkuil-cisco@...all.nl> wrote:
> >>>>>>
> >>>>>> On 22/10/2020 14:24, Alexandre Courbot wrote:
> >>>>>>> do_poll()/do_select() seem to set the _qproc member of poll_table to
> >>>>>>> NULL the first time they are called on a given table, making subsequent
> >>>>>>> calls of poll_wait() on that table no-ops. This is a problem for mem2mem
> >>>>>>> which calls poll_wait() on the V4L2 queues' waitqueues only when a
> >>>>>>> queue-related event is requested, which may not necessarily be the case
> >>>>>>> during the first poll.
> >>>>>>>
> >>>>>>> For instance, a stateful decoder is typically only interested in
> >>>>>>> EPOLLPRI events when it starts, and will switch to listening to both
> >>>>>>> EPOLLPRI and EPOLLIN after receiving the initial resolution change event
> >>>>>>> and configuring the CAPTURE queue. However by the time that switch
> >>>>>>> happens and v4l2_m2m_poll_for_data() is called for the first time,
> >>>>>>> poll_wait() has become a no-op and the V4L2 queues waitqueues thus
> >>>>>>> cannot be registered.
> >>>>>>>
> >>>>>>> Fix this by moving the registration to v4l2_m2m_poll() and do it whether
> >>>>>>> or not one of the queue-related events are requested.
> >>>>>>
> >>>>>> This looks good, but would it be possible to add a test for this to
> >>>>>> v4l2-compliance? (Look for POLL_MODE_EPOLL in v4l2-test-buffers.cpp)
> >>>>>>
> >>>>>> If I understand this right, calling EPOLL_CTL_ADD for EPOLLPRI, then
> >>>>>> calling EPOLL_CTL_ADD for EPOLLIN/OUT would trigger this? Or does there
> >>>>>> have to be an epoll_wait call in between?
> >>>>>
> >>>>> Even without an epoll_wait() in between the behavior is visible.
> >>>>> v4l2_m2m_poll() will be called once during the initial EPOLL_CTL_ADD
> >>>>> and this will trigger the bug.
> >>>>>
> >>>>>> Another reason for adding this test is that I wonder if regular capture
> >>>>>> or output V4L2 devices don't have the same issue.
> >>>>>>
> >>>>>> It's a very subtle bug and so adding a test for this to v4l2-compliance
> >>>>>> would be very useful.
> >>>>>
> >>>>> I fully agree, this is very counter-intuitive since what basically
> >>>>> happens is that the kernel's poll_wait() function becomes a no-op
> >>>>> after the poll() hook of a driver is called for the first time. There
> >>>>> is no way one can expect this behavior just from browsing the code so
> >>>>> this is likely to affect other drivers.
> >>>>>
> >>>>> As for the test itself, we can easily reproduce the conditions for
> >>>>> failure in v4l2-test-buffers.cpp's captureBufs() function, but doing
> >>>>> so will make the streaming tests fail without being specific about the
> >>>>> cause. Or maybe we should add another pollmode to specifically test
> >>>>> epoll in this setup? Can I get your thoughts?
> >>>>
> >>>> No, just keep it as part of the poll test. Just add comments at the place
> >>>> where it fails describing this error.
> >>>>
> >>>> After all, it *is* a poll() bug, so it is only fair that it is tested as
> >>>> part of the epoll test.
> >>>>
> >>>> Can you call EPOLL_CTL_ADD with ev.events set to 0? And then call it again
> >>>> with the actual value that you need? If that triggers this issue as well,
> >>>> then that is a nice test (but perhaps EPOLL_CTL_ADD won't call poll() if
> >>>> ev.events is 0, but perhaps EPOLLERR would work instead of 0).
> >>>
> >>> Yup, actually the following is enough to make v4l2-compliance -s fail
> >>> with vicodec:
> >>
> >> Does it also fail with vivid? I am curious to know whether this issue is
> >> m2m specific or a more general problem.
> >
> > It does fail actually! And that made me notice that vb2_poll() uses
> > the same pattern as v4l2_m2m_poll() (probably because the latter is
> > inspired by the former?) and needs to be fixed similarly. I will send
> > another patch to fix vb2_poll() as well, thanks for pointing it out!
>
> I was afraid of that.
>
> Testing epoll for control events would be interesting as well. The
> vivid radio device is an example of a device that has controls, but
> does not do streaming (so is not using vb2).
>
> But from what I can see v4l2_ctrl_poll() does the right thing, so this
> should be fine.

Indeed, it unconditionally calls poll_wait() with all the wait queues
that may wake us up (that is, only one), so there is no problem there.

Powered by blists - more mailing lists