| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20201112155305.GA1908425@aptenodytes>
Date: Thu, 12 Nov 2020 16:53:05 +0100
From: Paul Kocialkowski <paul.kocialkowski@...tlin.com>
To: Sakari Ailus <sakari.ailus@...ux.intel.com>
Cc: linux-media@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org,
Mauro Carvalho Chehab <mchehab@...nel.org>,
Rob Herring <robh+dt@...nel.org>,
Liam Girdwood <lgirdwood@...il.com>,
Mark Brown <broonie@...nel.org>,
Thomas Petazzoni <thomas.petazzoni@...tlin.com>,
Hans Verkuil <hverkuil@...all.nl>,
Maxime Ripard <mripard@...nel.org>
Subject: Re: [PATCH 2/2] media: i2c: Add support for the OV5648 image sensor
Hi Sakari,
On Fri 30 Oct 20, 18:52, Sakari Ailus wrote:
> Thank you for the patchset.
And thanks for the review!
> It's nice to see a driver that is not based on register lists --- most are.
>
> On Fri, Oct 23, 2020 at 07:49:44PM +0200, Paul Kocialkowski wrote:
> > The OV5648 is a 5 Mpx CMOS image sensor, connected via MIPI CSI-2
> > in a two-lane configuration.
>
> One or two, I guess?
Yes that's correct, I'll fix the commit message.
> > Most of the features of the hardware are supported, including:
> > - Auto and manual exposition/gain
> > - Auto and manual white balance
> > - Horizontal and vertical flip
> > - Test patterns
> >
> > But the following are still missing:
> > - Debanding, based on power source frequency;
> > - Exposition setting correlated to time units.
> >
> > Signed-off-by: Paul Kocialkowski <paul.kocialkowski@...tlin.com>
> > ---
> > drivers/media/i2c/Kconfig | 14 +
> > drivers/media/i2c/Makefile | 1 +
> > drivers/media/i2c/ov5648.c | 2680 ++++++++++++++++++++++++++++++++++++
> > 3 files changed, 2695 insertions(+)
> > create mode 100644 drivers/media/i2c/ov5648.c
> >
> > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> > index 48ae60a2c603..49f4e261c48e 100644
> > --- a/drivers/media/i2c/Kconfig
> > +++ b/drivers/media/i2c/Kconfig
> > @@ -922,6 +922,20 @@ config VIDEO_OV5647
> > To compile this driver as a module, choose M here: the
> > module will be called ov5647.
> >
> > +config VIDEO_OV5648
> > + tristate "OmniVision OV5648 sensor support"
> > + depends on OF
> > + depends on I2C && VIDEO_V4L2
> > + select MEDIA_CONTROLLER
> > + select VIDEO_V4L2_SUBDEV_API
> > + select V4L2_FWNODE
> > + help
> > + This is a Video4Linux2 sensor driver for the OmniVision
> > + OV5648 camera.
> > +
> > + To compile this driver as a module, choose M here: the
> > + module will be called ov5648.
> > +
> > config VIDEO_OV6650
> > tristate "OmniVision OV6650 sensor support"
> > depends on I2C && VIDEO_V4L2
> > diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
> > index f0a77473979d..15d4d6382582 100644
> > --- a/drivers/media/i2c/Makefile
> > +++ b/drivers/media/i2c/Makefile
> > @@ -71,6 +71,7 @@ obj-$(CONFIG_VIDEO_OV2740) += ov2740.o
> > obj-$(CONFIG_VIDEO_OV5640) += ov5640.o
> > obj-$(CONFIG_VIDEO_OV5645) += ov5645.o
> > obj-$(CONFIG_VIDEO_OV5647) += ov5647.o
> > +obj-$(CONFIG_VIDEO_OV5648) += ov5648.o
> > obj-$(CONFIG_VIDEO_OV5670) += ov5670.o
> > obj-$(CONFIG_VIDEO_OV5675) += ov5675.o
> > obj-$(CONFIG_VIDEO_OV5695) += ov5695.o
> > diff --git a/drivers/media/i2c/ov5648.c b/drivers/media/i2c/ov5648.c
> > new file mode 100644
> > index 000000000000..2c3c7f48de2f
> > --- /dev/null
> > +++ b/drivers/media/i2c/ov5648.c
> > @@ -0,0 +1,2680 @@
> > +/*
> > + * OmniVision OV5648 V4L2 driver
> > + *
> > + * Copyright (C) 2020 Bootlin
> > + * Author: Paul Kocialkowski <paul.kocialkowski@...tlin.com>
> > + *
> > + * This program is free software; you can redistribute it and/or
> > + * modify it under the terms of the GNU General Public License as
> > + * published by the Free Software Foundation version 2.
> > + *
> > + * This program is distributed .as is. WITHOUT ANY WARRANTY of any
> > + * kind, whether express or implied; without even the implied warranty
> > + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
>
> Please use SPDX tags instead.
Sure!
> > + */
> > +
> > +#include <linux/clk.h>
> > +#include <linux/delay.h>
> > +#include <linux/device.h>
> > +#include <linux/i2c.h>
> > +#include <linux/module.h>
> > +#include <linux/of_graph.h>
> > +#include <linux/regulator/consumer.h>
> > +#include <linux/videodev2.h>
> > +#include <media/v4l2-ctrls.h>
> > +#include <media/v4l2-device.h>
> > +#include <media/v4l2-fwnode.h>
> > +#include <media/v4l2-image-sizes.h>
> > +#include <media/v4l2-mediabus.h>
> > +
> > +/* Clock rate */
> > +
> > +#define OV5648_XVCLK_RATE 24000000
> > +
> > +/* Register definitions */
> > +
> > +/* System */
> > +
> > +#define OV5648_SW_STANDBY_REG 0x100
> > +#define OV5648_SW_STANDBY_STREAM_ON BIT(0)
> > +
> > +#define OV5648_SW_RESET_REG 0x103
> > +#define OV5648_SW_RESET_RESET BIT(0)
> > +
> > +#define OV5648_PAD_OEN0_REG 0x3000
> > +#define OV5648_PAD_OEN1_REG 0x3001
> > +#define OV5648_PAD_OEN2_REG 0x3002
> > +#define OV5648_PAD_OUT0_REG 0x3008
> > +#define OV5648_PAD_OUT1_REG 0x3009
> > +
> > +#define OV5648_CHIP_ID_H_REG 0x300a
> > +#define OV5648_CHIP_ID_H_VALUE 0x56
> > +#define OV5648_CHIP_ID_L_REG 0x300b
> > +#define OV5648_CHIP_ID_L_VALUE 0x48
> > +
> > +#define OV5648_PAD_OUT2_REG 0x300d
> > +#define OV5648_PAD_SEL0_REG 0x300e
> > +#define OV5648_PAD_SEL1_REG 0x300f
> > +#define OV5648_PAD_SEL2_REG 0x3010
> > +#define OV5648_PAD_PK_REG 0x3011
> > +#define OV5648_PAD_PK_PD_DATO_EN BIT(7)
> > +#define OV5648_PAD_PK_DRIVE_STRENGTH_1X (0 << 5)
> > +#define OV5648_PAD_PK_DRIVE_STRENGTH_2X (2 << 5)
> > +#define OV5648_PAD_PK_FREX_N BIT(1)
> > +
> > +#define OV5648_A_PWC_PK_O0_REG 0x3013
> > +#define OV5648_A_PWC_PK_O0_BP_REGULATOR_N BIT(3)
> > +#define OV5648_A_PWC_PK_O1_REG 0x3014
> > +
> > +#define OV5648_MIPI_PHY0_REG 0x3016
> > +#define OV5648_MIPI_PHY1_REG 0x3017
> > +#define OV5648_MIPI_SC_CTRL0_REG 0x3018
> > +#define OV5648_MIPI_SC_CTRL0_MIPI_LANES(v) (((v) << 5) & GENMASK(7, 5))
> > +#define OV5648_MIPI_SC_CTRL0_PHY_HS_TX_PD BIT(4)
> > +#define OV5648_MIPI_SC_CTRL0_PHY_LP_RX_PD BIT(3)
> > +#define OV5648_MIPI_SC_CTRL0_MIPI_EN BIT(2)
> > +#define OV5648_MIPI_SC_CTRL0_MIPI_SUSP BIT(1)
> > +#define OV5648_MIPI_SC_CTRL0_LANE_DIS_OP BIT(0)
> > +#define OV5648_MIPI_SC_CTRL1_REG 0x3019
> > +#define OV5648_MISC_CTRL0_REG 0x3021
> > +#define OV5648_MIPI_SC_CTRL2_REG 0x3022
> > +#define OV5648_SUB_ID_REG 0x302a
> > +
> > +#define OV5648_PLL_CTRL0_REG 0x3034
> > +#define OV5648_PLL_CTRL0_PLL_CHARGE_PUMP(v) (((v) << 4) & GENMASK(6, 4))
> > +#define OV5648_PLL_CTRL0_BITS(v) ((v) & GENMASK(3, 0))
> > +#define OV5648_PLL_CTRL1_REG 0x3035
> > +#define OV5648_PLL_CTRL1_SYS_DIV(v) (((v) << 4) & GENMASK(7, 4))
> > +#define OV5648_PLL_CTRL1_MIPI_DIV(v) ((v) & GENMASK(3, 0))
> > +#define OV5648_PLL_MUL_REG 0x3036
> > +#define OV5648_PLL_MUL(v) ((v) & GENMASK(7, 0))
> > +#define OV5648_PLL_DIV_REG 0x3037
> > +#define OV5648_PLL_DIV_ROOT_DIV(v) ((((v) - 1) << 4) & BIT(4))
> > +#define OV5648_PLL_DIV_PLL_PRE_DIV(v) ((v) & GENMASK(3, 0))
> > +#define OV5648_PLL_DEBUG_REG 0x3038
> > +#define OV5648_PLL_BYPASS_REG 0x3039
> > +
> > +#define OV5648_PLLS_BYPASS_REG 0x303a
> > +#define OV5648_PLLS_MUL_REG 0x303b
> > +#define OV5648_PLLS_MUL(v) ((v) & GENMASK(4, 0))
> > +#define OV5648_PLLS_CTRL_REG 0x303c
> > +#define OV5648_PLLS_CTRL_PLL_CHARGE_PUMP(v) (((v) << 4) & GENMASK(6, 4))
> > +#define OV5648_PLLS_CTRL_SYS_DIV(v) ((v) & GENMASK(3, 0))
> > +#define OV5648_PLLS_DIV_REG 0x303d
> > +#define OV5648_PLLS_DIV_PLLS_PRE_DIV(v) (((v) << 4) & GENMASK(5, 4))
> > +#define OV5648_PLLS_DIV_PLLS_DIV_R(v) ((((v) - 1) << 2) & BIT(2))
> > +#define OV5648_PLLS_DIV_PLLS_SEL_DIV(v) ((v) & GENMASK(1, 0))
> > +
> > +#define OV5648_SRB_CTRL_REG 0x3106
> > +#define OV5648_SRB_CTRL_SCLK_DIV(v) (((v) << 2) & GENMASK(3, 2))
> > +#define OV5648_SRB_CTRL_RESET_ARBITER_EN BIT(1)
> > +#define OV5648_SRB_CTRL_SCLK_ARBITER_EN BIT(0)
> > +
> > +/* Group Hold */
> > +
> > +#define OV5648_GROUP_ADR0_REG 0x3200
> > +#define OV5648_GROUP_ADR1_REG 0x3201
> > +#define OV5648_GROUP_ADR2_REG 0x3202
> > +#define OV5648_GROUP_ADR3_REG 0x3203
> > +#define OV5648_GROUP_LEN0_REG 0x3204
> > +#define OV5648_GROUP_LEN1_REG 0x3205
> > +#define OV5648_GROUP_LEN2_REG 0x3206
> > +#define OV5648_GROUP_LEN3_REG 0x3207
> > +#define OV5648_GROUP_ACCESS_REG 0x3208
> > +
> > +/* Exposure/gain/banding */
> > +
> > +#define OV5648_EXPOSURE_CTRL_HH_REG 0x3500
> > +#define OV5648_EXPOSURE_CTRL_HH(v) (((v) & GENMASK(19, 16)) >> 16)
> > +#define OV5648_EXPOSURE_CTRL_HH_VALUE(v) (((v) << 16) & GENMASK(19, 16))
> > +#define OV5648_EXPOSURE_CTRL_H_REG 0x3501
> > +#define OV5648_EXPOSURE_CTRL_H(v) (((v) & GENMASK(15, 8)) >> 8)
> > +#define OV5648_EXPOSURE_CTRL_H_VALUE(v) (((v) << 8) & GENMASK(15, 8))
> > +#define OV5648_EXPOSURE_CTRL_L_REG 0x3502
> > +#define OV5648_EXPOSURE_CTRL_L(v) ((v) & GENMASK(7, 0))
> > +#define OV5648_EXPOSURE_CTRL_L_VALUE(v) ((v) & GENMASK(7, 0))
> > +#define OV5648_MANUAL_CTRL_REG 0x3503
> > +#define OV5648_MANUAL_CTRL_FRAME_DELAY(v) (((v) << 4) & GENMASK(5, 4))
> > +#define OV5648_MANUAL_CTRL_AGC_MANUAL_EN BIT(1)
> > +#define OV5648_MANUAL_CTRL_AEC_MANUAL_EN BIT(0)
> > +#define OV5648_GAIN_CTRL_H_REG 0x350a
> > +#define OV5648_GAIN_CTRL_H(v) (((v) & GENMASK(9, 8)) >> 8)
> > +#define OV5648_GAIN_CTRL_H_VALUE(v) (((v) << 8) & GENMASK(9, 8))
> > +#define OV5648_GAIN_CTRL_L_REG 0x350b
> > +#define OV5648_GAIN_CTRL_L(v) ((v) & GENMASK(7, 0))
> > +#define OV5648_GAIN_CTRL_L_VALUE(v) ((v) & GENMASK(7, 0))
> > +
> > +#define OV5648_ANALOG_CTRL0_REG_BASE 0x3600
> > +#define OV5648_ANALOG_CTRL1_REG_BASE 0x3700
> > +
> > +#define OV5648_AEC_CTRL0_REG 0x3a00
> > +#define OV5648_AEC_CTRL0_DEBUG BIT(6)
> > +#define OV5648_AEC_CTRL0_DEBAND_EN BIT(5)
> > +#define OV5648_AEC_CTRL0_DEBAND_LOW_LIMIT_EN BIT(4)
> > +#define OV5648_AEC_CTRL0_START_SEL_EN BIT(3)
> > +#define OV5648_AEC_CTRL0_NIGHT_MODE_EN BIT(2)
> > +#define OV5648_AEC_CTRL0_FREEZE_EN BIT(0)
> > +#define OV5648_EXPOSURE_MIN_REG 0x3a01
> > +#define OV5648_EXPOSURE_MAX_60_H_REG 0x3a02
> > +#define OV5648_EXPOSURE_MAX_60_L_REG 0x3a03
> > +#define OV5648_AEC_CTRL5_REG 0x3a05
> > +#define OV5648_AEC_CTRL6_REG 0x3a06
> > +#define OV5648_AEC_CTRL7_REG 0x3a07
> > +#define OV5648_BANDING_STEP_50_H_REG 0x3a08
> > +#define OV5648_BANDING_STEP_50_L_REG 0x3a09
> > +#define OV5648_BANDING_STEP_60_H_REG 0x3a0a
> > +#define OV5648_BANDING_STEP_60_L_REG 0x3a0b
> > +#define OV5648_AEC_CTRLC_REG 0x3a0c
> > +#define OV5648_BANDING_MAX_60_REG 0x3a0d
> > +#define OV5648_BANDING_MAX_50_REG 0x3a0e
> > +#define OV5648_WPT_REG 0x3a0f
> > +#define OV5648_BPT_REG 0x3a10
> > +#define OV5648_VPT_HIGH_REG 0x3a11
> > +#define OV5648_AVG_MANUAL_REG 0x3a12
> > +#define OV5648_PRE_GAIN_REG 0x3a13
> > +#define OV5648_EXPOSURE_MAX_50_H_REG 0x3a14
> > +#define OV5648_EXPOSURE_MAX_50_L_REG 0x3a15
> > +#define OV5648_GAIN_BASE_NIGHT_REG 0x3a17
> > +#define OV5648_AEC_GAIN_CEILING_H_REG 0x3a18
> > +#define OV5648_AEC_GAIN_CEILING_L_REG 0x3a19
> > +#define OV5648_DIFF_MAX_REG 0x3a1a
> > +#define OV5648_WPT2_REG 0x3a1b
> > +#define OV5648_LED_ADD_ROW_H_REG 0x3a1c
> > +#define OV5648_LED_ADD_ROW_L_REG 0x3a1d
> > +#define OV5648_BPT2_REG 0x3a1e
> > +#define OV5648_VPT_LOW_REG 0x3a1f
> > +#define OV5648_AEC_CTRL20_REG 0x3a20
> > +#define OV5648_AEC_CTRL21_REG 0x3a21
> > +
> > +#define OV5648_AVG_START_X_H_REG 0x5680
> > +#define OV5648_AVG_START_X_L_REG 0x5681
> > +#define OV5648_AVG_START_Y_H_REG 0x5682
> > +#define OV5648_AVG_START_Y_L_REG 0x5683
> > +#define OV5648_AVG_WINDOW_X_H_REG 0x5684
> > +#define OV5648_AVG_WINDOW_X_L_REG 0x5685
> > +#define OV5648_AVG_WINDOW_Y_H_REG 0x5686
> > +#define OV5648_AVG_WINDOW_Y_L_REG 0x5687
> > +#define OV5648_AVG_WEIGHT00_REG 0x5688
> > +#define OV5648_AVG_WEIGHT01_REG 0x5689
> > +#define OV5648_AVG_WEIGHT02_REG 0x568a
> > +#define OV5648_AVG_WEIGHT03_REG 0x568b
> > +#define OV5648_AVG_WEIGHT04_REG 0x568c
> > +#define OV5648_AVG_WEIGHT05_REG 0x568d
> > +#define OV5648_AVG_WEIGHT06_REG 0x568e
> > +#define OV5648_AVG_WEIGHT07_REG 0x568f
> > +#define OV5648_AVG_CTRL10_REG 0x5690
> > +#define OV5648_AVG_WEIGHT_SUM_REG 0x5691
> > +#define OV5648_AVG_READOUT_REG 0x5693
> > +
> > +#define OV5648_DIG_CTRL0_REG 0x5a00
> > +#define OV5648_DIG_COMP_MAN_H_REG 0x5a02
> > +#define OV5648_DIG_COMP_MAN_L_REG 0x5a03
> > +
> > +#define OV5648_GAINC_MAN_H_REG 0x5a20
> > +#define OV5648_GAINC_MAN_L_REG 0x5a21
> > +#define OV5648_GAINC_DGC_MAN_H_REG 0x5a22
> > +#define OV5648_GAINC_DGC_MAN_L_REG 0x5a23
> > +#define OV5648_GAINC_CTRL0_REG 0x5a24
> > +
> > +#define OV5648_GAINF_ANA_NUM_REG 0x5a40
> > +#define OV5648_GAINF_DIG_GAIN_REG 0x5a41
> > +
> > +/* Timing */
> > +
> > +#define OV5648_CROP_START_X_H_REG 0x3800
> > +#define OV5648_CROP_START_X_H(v) (((v) & GENMASK(11, 8)) >> 8)
> > +#define OV5648_CROP_START_X_L_REG 0x3801
> > +#define OV5648_CROP_START_X_L(v) ((v) & GENMASK(7, 0))
> > +#define OV5648_CROP_START_Y_H_REG 0x3802
> > +#define OV5648_CROP_START_Y_H(v) (((v) & GENMASK(11, 8)) >> 8)
> > +#define OV5648_CROP_START_Y_L_REG 0x3803
> > +#define OV5648_CROP_START_Y_L(v) ((v) & GENMASK(7, 0))
> > +#define OV5648_CROP_END_X_H_REG 0x3804
> > +#define OV5648_CROP_END_X_H(v) (((v) & GENMASK(11, 8)) >> 8)
> > +#define OV5648_CROP_END_X_L_REG 0x3805
> > +#define OV5648_CROP_END_X_L(v) ((v) & GENMASK(7, 0))
> > +#define OV5648_CROP_END_Y_H_REG 0x3806
> > +#define OV5648_CROP_END_Y_H(v) (((v) & GENMASK(11, 8)) >> 8)
> > +#define OV5648_CROP_END_Y_L_REG 0x3807
> > +#define OV5648_CROP_END_Y_L(v) ((v) & GENMASK(7, 0))
> > +#define OV5648_OUTPUT_SIZE_X_H_REG 0x3808
> > +#define OV5648_OUTPUT_SIZE_X_H(v) (((v) & GENMASK(11, 8)) >> 8)
> > +#define OV5648_OUTPUT_SIZE_X_L_REG 0x3809
> > +#define OV5648_OUTPUT_SIZE_X_L(v) ((v) & GENMASK(7, 0))
> > +#define OV5648_OUTPUT_SIZE_Y_H_REG 0x380a
> > +#define OV5648_OUTPUT_SIZE_Y_H(v) (((v) & GENMASK(11, 8)) >> 8)
> > +#define OV5648_OUTPUT_SIZE_Y_L_REG 0x380b
> > +#define OV5648_OUTPUT_SIZE_Y_L(v) ((v) & GENMASK(7, 0))
> > +#define OV5648_HTS_H_REG 0x380c
> > +#define OV5648_HTS_H(v) (((v) & GENMASK(12, 8)) >> 8)
> > +#define OV5648_HTS_L_REG 0x380d
> > +#define OV5648_HTS_L(v) ((v) & GENMASK(7, 0))
> > +#define OV5648_VTS_H_REG 0x380e
> > +#define OV5648_VTS_H(v) (((v) & GENMASK(15, 8)) >> 8)
> > +#define OV5648_VTS_L_REG 0x380f
> > +#define OV5648_VTS_L(v) ((v) & GENMASK(7, 0))
> > +#define OV5648_OFFSET_X_H_REG 0x3810
> > +#define OV5648_OFFSET_X_H(v) (((v) & GENMASK(11, 8)) >> 8)
> > +#define OV5648_OFFSET_X_L_REG 0x3811
> > +#define OV5648_OFFSET_X_L(v) ((v) & GENMASK(7, 0))
> > +#define OV5648_OFFSET_Y_H_REG 0x3812
> > +#define OV5648_OFFSET_Y_H(v) (((v) & GENMASK(11, 8)) >> 8)
> > +#define OV5648_OFFSET_Y_L_REG 0x3813
> > +#define OV5648_OFFSET_Y_L(v) ((v) & GENMASK(7, 0))
> > +#define OV5648_SUB_INC_X_REG 0x3814
> > +#define OV5648_SUB_INC_X_ODD(v) (((v) << 4) & GENMASK(7, 4))
> > +#define OV5648_SUB_INC_X_EVEN(v) ((v) & GENMASK(3, 0))
> > +#define OV5648_SUB_INC_Y_REG 0x3815
> > +#define OV5648_SUB_INC_Y_ODD(v) (((v) << 4) & GENMASK(7, 4))
> > +#define OV5648_SUB_INC_Y_EVEN(v) ((v) & GENMASK(3, 0))
> > +#define OV5648_HSYNCST_H_REG 0x3816
> > +#define OV5648_HSYNCST_H(v) (((v) >> 8) & 0xf)
> > +#define OV5648_HSYNCST_L_REG 0x3817
> > +#define OV5648_HSYNCST_L(v) ((v) & GENMASK(7, 0))
> > +#define OV5648_HSYNCW_H_REG 0x3818
> > +#define OV5648_HSYNCW_H(v) (((v) >> 8) & 0xf)
> > +#define OV5648_HSYNCW_L_REG 0x3819
> > +#define OV5648_HSYNCW_L(v) ((v) & GENMASK(7, 0))
> > +
> > +#define OV5648_TC20_REG 0x3820
> > +#define OV5648_TC20_DEBUG BIT(6)
> > +#define OV5648_TC20_FLIP_VERT_ISP_EN BIT(2)
> > +#define OV5648_TC20_FLIP_VERT_SENSOR_EN BIT(1)
> > +#define OV5648_TC20_BINNING_VERT_EN BIT(0)
> > +#define OV5648_TC21_REG 0x3821
> > +#define OV5648_TC21_FLIP_HORZ_ISP_EN BIT(2)
> > +#define OV5648_TC21_FLIP_HORZ_SENSOR_EN BIT(1)
> > +#define OV5648_TC21_BINNING_HORZ_EN BIT(0)
> > +
> > +/* Strobe/exposure */
> > +
> > +#define OV5648_STROBE_REG 0x3b00
> > +#define OV5648_FREX_EXP_HH_REG 0x3b01
> > +#define OV5648_SHUTTER_DLY_H_REG 0x3b02
> > +#define OV5648_SHUTTER_DLY_L_REG 0x3b03
> > +#define OV5648_FREX_EXP_H_REG 0x3b04
> > +#define OV5648_FREX_EXP_L_REG 0x3b05
> > +#define OV5648_FREX_CTRL_REG 0x3b06
> > +#define OV5648_FREX_MODE_SEL_REG 0x3b07
> > +#define OV5648_FREX_MODE_SEL_FREX_SA1 BIT(4)
> > +#define OV5648_FREX_MODE_SEL_FX1_FM_EN BIT(3)
> > +#define OV5648_FREX_MODE_SEL_FREX_INV BIT(2)
> > +#define OV5648_FREX_MODE_SEL_MODE1 0x0
> > +#define OV5648_FREX_MODE_SEL_MODE2 0x1
> > +#define OV5648_FREX_MODE_SEL_ROLLING 0x2
> > +#define OV5648_FREX_EXP_REQ_REG 0x3b08
> > +#define OV5648_FREX_SHUTTER_DLY_REG 0x3b09
> > +#define OV5648_FREX_RST_LEN_REG 0x3b0a
> > +#define OV5648_STROBE_WIDTH_HH_REG 0x3b0b
> > +#define OV5648_STROBE_WIDTH_H_REG 0x3b0c
> > +
> > +/* OTP */
> > +
> > +#define OV5648_OTP_DATA_REG_BASE 0x3d00
> > +#define OV5648_OTP_PROGRAM_CTRL_REG 0x3d80
> > +#define OV5648_OTP_LOAD_CTRL_REG 0x3d81
> > +
> > +/* PSRAM */
> > +
> > +#define OV5648_PSRAM_CTRL1_REG 0x3f01
> > +#define OV5648_PSRAM_CTRLF_REG 0x3f0f
> > +
> > +/* Black Level */
> > +
> > +#define OV5648_BLC_CTRL0_REG 0x4000
> > +#define OV5648_BLC_CTRL1_REG 0x4001
> > +#define OV5648_BLC_CTRL1_START_LINE(v) ((v) & GENMASK(5, 0))
> > +#define OV5648_BLC_CTRL2_REG 0x4002
> > +#define OV5648_BLC_CTRL2_AUTO_EN BIT(6)
> > +#define OV5648_BLC_CTRL2_RESET_FRAME_NUM(v) ((v) & GENMASK(5, 0))
> > +#define OV5648_BLC_CTRL3_REG 0x4003
> > +#define OV5648_BLC_LINE_NUM_REG 0x4004
> > +#define OV5648_BLC_LINE_NUM(v) ((v) & GENMASK(7, 0))
> > +#define OV5648_BLC_CTRL5_REG 0x4005
> > +#define OV5648_BLC_CTRL5_UPDATE_EN BIT(1)
> > +#define OV5648_BLC_LEVEL_REG 0x4009
> > +
> > +/* Frame */
> > +
> > +#define OV5648_FRAME_CTRL_REG 0x4200
> > +#define OV5648_FRAME_ON_NUM_REG 0x4201
> > +#define OV5648_FRAME_OFF_NUM_REG 0x4202
> > +
> > +/* MIPI CSI-2 */
> > +
> > +#define OV5648_MIPI_CTRL0_REG 0x4800
> > +#define OV5648_MIPI_CTRL0_CLK_LANE_AUTOGATE BIT(5)
> > +#define OV5648_MIPI_CTRL0_LANE_SYNC_EN BIT(4)
> > +#define OV5648_MIPI_CTRL0_LANE_SELECT_LANE1 0
> > +#define OV5648_MIPI_CTRL0_LANE_SELECT_LANE2 BIT(3)
> > +#define OV5648_MIPI_CTRL0_IDLE_LP00 0
> > +#define OV5648_MIPI_CTRL0_IDLE_LP11 BIT(2)
> > +
> > +#define OV5648_MIPI_CTRL1_REG 0x4801
> > +#define OV5648_MIPI_CTRL2_REG 0x4802
> > +#define OV5648_MIPI_CTRL3_REG 0x4803
> > +#define OV5648_MIPI_CTRL4_REG 0x4804
> > +#define OV5648_MIPI_CTRL5_REG 0x4805
> > +#define OV5648_MIPI_MAX_FRAME_COUNT_H_REG 0x4810
> > +#define OV5648_MIPI_MAX_FRAME_COUNT_L_REG 0x4811
> > +#define OV5648_MIPI_CTRL14_REG 0x4814
> > +#define OV5648_MIPI_DT_SPKT_REG 0x4815
> > +#define OV5648_MIPI_HS_ZERO_MIN_H_REG 0x4818
> > +#define OV5648_MIPI_HS_ZERO_MIN_L_REG 0x4819
> > +#define OV5648_MIPI_HS_TRAIN_MIN_H_REG 0x481a
> > +#define OV5648_MIPI_HS_TRAIN_MIN_L_REG 0x481b
> > +#define OV5648_MIPI_CLK_ZERO_MIN_H_REG 0x481c
> > +#define OV5648_MIPI_CLK_ZERO_MIN_L_REG 0x481d
> > +#define OV5648_MIPI_CLK_PREPARE_MIN_H_REG 0x481e
> > +#define OV5648_MIPI_CLK_PREPARE_MIN_L_REG 0x481f
> > +#define OV5648_MIPI_CLK_POST_MIN_H_REG 0x4820
> > +#define OV5648_MIPI_CLK_POST_MIN_L_REG 0x4821
> > +#define OV5648_MIPI_CLK_TRAIL_MIN_H_REG 0x4822
> > +#define OV5648_MIPI_CLK_TRAIL_MIN_L_REG 0x4823
> > +#define OV5648_MIPI_LPX_P_MIN_H_REG 0x4824
> > +#define OV5648_MIPI_LPX_P_MIN_L_REG 0x4825
> > +#define OV5648_MIPI_HS_PREPARE_MIN_H_REG 0x4826
> > +#define OV5648_MIPI_HS_PREPARE_MIN_L_REG 0x4827
> > +#define OV5648_MIPI_HS_EXIT_MIN_H_REG 0x4828
> > +#define OV5648_MIPI_HS_EXIT_MIN_L_REG 0x4829
> > +#define OV5648_MIPI_HS_ZERO_MIN_UI_REG 0x482a
> > +#define OV5648_MIPI_HS_TRAIL_MIN_UI_REG 0x482b
> > +#define OV5648_MIPI_CLK_ZERO_MIN_UI_REG 0x482c
> > +#define OV5648_MIPI_CLK_PREPARE_MIN_UI_REG 0x482d
> > +#define OV5648_MIPI_CLK_POST_MIN_UI_REG 0x482e
> > +#define OV5648_MIPI_CLK_TRAIL_MIN_UI_REG 0x482f
> > +#define OV5648_MIPI_LPX_P_MIN_UI_REG 0x4830
> > +#define OV5648_MIPI_HS_PREPARE_MIN_UI_REG 0x4831
> > +#define OV5648_MIPI_HS_EXIT_MIN_UI_REG 0x4832
> > +#define OV5648_MIPI_REG_MIN_H_REG 0x4833
> > +#define OV5648_MIPI_REG_MIN_L_REG 0x4834
> > +#define OV5648_MIPI_REG_MAX_H_REG 0x4835
> > +#define OV5648_MIPI_REG_MAX_L_REG 0x4836
> > +#define OV5648_MIPI_PCLK_PERIOD_REG 0x4837
> > +#define OV5648_MIPI_WKUP_DLY_REG 0x4838
> > +#define OV5648_MIPI_LP_GPIO_REG 0x483b
> > +#define OV5648_MIPI_SNR_PCLK_DIV_REG 0x4843
> > +
> > +/* ISP */
> > +
> > +#define OV5648_ISP_CTRL0_REG 0x5000
> > +#define OV5648_ISP_CTRL0_BLACK_CORRECT_EN BIT(2)
> > +#define OV5648_ISP_CTRL0_WHITE_CORRECT_EN BIT(1)
> > +#define OV5648_ISP_CTRL1_REG 0x5001
> > +#define OV5648_ISP_CTRL1_AWB_EN BIT(0)
> > +#define OV5648_ISP_CTRL2_REG 0x5002
> > +#define OV5648_ISP_CTRL2_WIN_EN BIT(6)
> > +#define OV5648_ISP_CTRL2_OTP_EN BIT(1)
> > +#define OV5648_ISP_CTRL2_AWB_GAIN_EN BIT(0)
> > +#define OV5648_ISP_CTRL3_REG 0x5003
> > +#define OV5648_ISP_CTRL3_BUF_EN BIT(3)
> > +#define OV5648_ISP_CTRL3_BIN_MAN_SET BIT(2)
> > +#define OV5648_ISP_CTRL3_BIN_AUTO_EN BIT(1)
> > +#define OV5648_ISP_CTRL4_REG 0x5004
> > +#define OV5648_ISP_CTRL5_REG 0x5005
> > +#define OV5648_ISP_CTRL6_REG 0x5006
> > +#define OV5648_ISP_CTRL7_REG 0x5007
> > +#define OV5648_ISP_MAN_OFFSET_X_H_REG 0x5008
> > +#define OV5648_ISP_MAN_OFFSET_X_L_REG 0x5009
> > +#define OV5648_ISP_MAN_OFFSET_Y_H_REG 0x500a
> > +#define OV5648_ISP_MAN_OFFSET_Y_L_REG 0x500b
> > +#define OV5648_ISP_MAN_WIN_OFFSET_X_H_REG 0x500c
> > +#define OV5648_ISP_MAN_WIN_OFFSET_X_L_REG 0x500d
> > +#define OV5648_ISP_MAN_WIN_OFFSET_Y_H_REG 0x500e
> > +#define OV5648_ISP_MAN_WIN_OFFSET_Y_L_REG 0x500f
> > +#define OV5648_ISP_MAN_WIN_OUTPUT_X_H_REG 0x5010
> > +#define OV5648_ISP_MAN_WIN_OUTPUT_X_L_REG 0x5011
> > +#define OV5648_ISP_MAN_WIN_OUTPUT_Y_H_REG 0x5012
> > +#define OV5648_ISP_MAN_WIN_OUTPUT_Y_L_REG 0x5013
> > +#define OV5648_ISP_MAN_INPUT_X_H_REG 0x5014
> > +#define OV5648_ISP_MAN_INPUT_X_L_REG 0x5015
> > +#define OV5648_ISP_MAN_INPUT_Y_H_REG 0x5016
> > +#define OV5648_ISP_MAN_INPUT_Y_L_REG 0x5017
> > +#define OV5648_ISP_CTRL18_REG 0x5018
> > +#define OV5648_ISP_CTRL19_REG 0x5019
> > +#define OV5648_ISP_CTRL1A_REG 0x501a
> > +#define OV5648_ISP_CTRL1D_REG 0x501d
> > +#define OV5648_ISP_CTRL1F_REG 0x501f
> > +#define OV5648_ISP_CTRL1F_OUTPUT_EN 3
> > +#define OV5648_ISP_CTRL25_REG 0x5025
> > +
> > +#define OV5648_ISP_CTRL3D_REG 0x503d
> > +#define OV5648_ISP_CTRL3D_PATTERN_EN BIT(7)
> > +#define OV5648_ISP_CTRL3D_ROLLING_BAR_EN BIT(6)
> > +#define OV5648_ISP_CTRL3D_TRANSPARENT_MODE BIT(5)
> > +#define OV5648_ISP_CTRL3D_SQUARES_BW_MODE BIT(4)
> > +#define OV5648_ISP_CTRL3D_PATTERN_COLOR_BARS 0
> > +#define OV5648_ISP_CTRL3D_PATTERN_RANDOM_DATA 1
> > +#define OV5648_ISP_CTRL3D_PATTERN_COLOR_SQUARES 2
> > +#define OV5648_ISP_CTRL3D_PATTERN_INPUT 3
> > +
> > +#define OV5648_ISP_CTRL3E_REG 0x503e
> > +#define OV5648_ISP_CTRL4B_REG 0x504b
> > +#define OV5648_ISP_CTRL4B_POST_BIN_H_EN BIT(5)
> > +#define OV5648_ISP_CTRL4B_POST_BIN_V_EN BIT(4)
> > +#define OV5648_ISP_CTRL4C_REG 0x504c
> > +#define OV5648_ISP_CTRL57_REG 0x5057
> > +#define OV5648_ISP_CTRL58_REG 0x5058
> > +#define OV5648_ISP_CTRL59_REG 0x5059
> > +
> > +#define OV5648_ISP_WINDOW_START_X_H_REG 0x5980
> > +#define OV5648_ISP_WINDOW_START_X_L_REG 0x5981
> > +#define OV5648_ISP_WINDOW_START_Y_H_REG 0x5982
> > +#define OV5648_ISP_WINDOW_START_Y_L_REG 0x5983
> > +#define OV5648_ISP_WINDOW_WIN_X_H_REG 0x5984
> > +#define OV5648_ISP_WINDOW_WIN_X_L_REG 0x5985
> > +#define OV5648_ISP_WINDOW_WIN_Y_H_REG 0x5986
> > +#define OV5648_ISP_WINDOW_WIN_Y_L_REG 0x5987
> > +#define OV5648_ISP_WINDOW_MAN_REG 0x5988
> > +
> > +/* White Balance */
> > +
> > +#define OV5648_AWB_CTRL_REG 0x5180
> > +#define OV5648_AWB_CTRL_FAST_AWB BIT(6)
> > +#define OV5648_AWB_CTRL_GAIN_FREEZE_EN BIT(5)
> > +#define OV5648_AWB_CTRL_SUM_FREEZE_EN BIT(4)
> > +#define OV5648_AWB_CTRL_GAIN_MANUAL_EN BIT(3)
> > +
> > +#define OV5648_AWB_DELTA_REG 0x5181
> > +#define OV5648_AWB_STABLE_RANGE_REG 0x5182
> > +#define OV5648_AWB_STABLE_RANGE_WIDE_REG 0x5183
> > +#define OV5648_HSIZE_MAN_REG 0x5185
> > +
> > +#define OV5648_GAIN_RED_MAN_H_REG 0x5186
> > +#define OV5648_GAIN_RED_MAN_H(v) (((v) & GENMASK(11, 8)) >> 8)
> > +#define OV5648_GAIN_RED_MAN_L_REG 0x5187
> > +#define OV5648_GAIN_RED_MAN_L(v) ((v) & GENMASK(7, 0))
> > +#define OV5648_GAIN_GREEN_MAN_H_REG 0x5188
> > +#define OV5648_GAIN_GREEN_MAN_H(v) (((v) & GENMASK(11, 8)) >> 8)
> > +#define OV5648_GAIN_GREEN_MAN_L_REG 0x5189
> > +#define OV5648_GAIN_GREEN_MAN_L(v) ((v) & GENMASK(7, 0))
> > +#define OV5648_GAIN_BLUE_MAN_H_REG 0x518a
> > +#define OV5648_GAIN_BLUE_MAN_H(v) (((v) & GENMASK(11, 8)) >> 8)
> > +#define OV5648_GAIN_BLUE_MAN_L_REG 0x518b
> > +#define OV5648_GAIN_BLUE_MAN_L(v) ((v) & GENMASK(7, 0))
> > +#define OV5648_GAIN_RED_LIMIT_REG 0x518c
> > +#define OV5648_GAIN_GREEN_LIMIT_REG 0x518d
> > +#define OV5648_GAIN_BLUE_LIMIT_REG 0x518e
> > +#define OV5648_AWB_FRAME_COUNT_REG 0x518f
> > +#define OV5648_AWB_BASE_MAN_REG 0x51df
> > +
> > +/* Macros */
> > +
> > +#define ov5648_subdev_sensor(subdev) \
> > + container_of(subdev, struct ov5648_sensor, subdev)
> > +
> > +#define ov5648_ctrl_subdev(ctrl) \
> > + (&container_of(ctrl->handler, struct ov5648_sensor, ctrls.handler)->subdev)
> > +
> > +/* Data structures */
> > +
> > +struct ov5648_register_value {
> > + u16 address;
> > + u8 value;
> > + unsigned int delay_ms;
> > +};
> > +
> > +/*
> > + * PLL1 Clock Tree:
> > + *
> > + * +-< XVCLK
> > + * |
> > + * +-+ pll_pre_div (0x3037 [3:0], special values: 5: 1.5, 7: 2.5)
> > + * |
> > + * +-+ pll_mul (0x3036 [7:0])
> > + * |
> > + * +-+ sys_div (0x3035 [7:4])
> > + * |
> > + * +-+ mipi_div (0x3035 [3:0])
> > + * | |
> > + * | +-> MIPI_SCLK
> > + * | |
> > + * | +-+ mipi_phy_div (2)
> > + * | |
> > + * | +-> MIPI_CLK
> > + * |
> > + * +-+ root_div (0x3037 [4])
> > + * |
> > + * +-+ bit_div (0x3034 [3:0], 8 bits: 2, 10 bits: 2.5, other: 1)
> > + * |
> > + * +-+ sclk_div (0x3106 [3:2])
> > + * |
> > + * +-> SCLK
> > + * |
> > + * +-+ mipi_div (0x3035, 1: PCLK = SCLK)
> > + * |
> > + * +-> PCLK
> > + */
> > +
> > +struct ov5648_pll1_config {
> > + unsigned int pll_pre_div;
> > + unsigned int pll_mul;
> > + unsigned int sys_div;
> > + unsigned int root_div;
> > + unsigned int sclk_div;
> > + unsigned int mipi_div;
> > +};
> > +
> > +/*
> > + * PLL2 Clock Tree:
> > + *
> > + * +-< XVCLK
> > + * |
> > + * +-+ plls_pre_div (0x303d [5:4], special values: 0: 1, 1: 1.5)
> > + * |
> > + * +-+ plls_div_r (0x303d [2])
> > + * |
> > + * +-+ plls_mul (0x303b [4:0])
> > + * |
> > + * +-+ sys_div (0x303c [3:0])
> > + * |
> > + * +-+ sel_div (0x303d [1:0], special values: 0: 1, 3: 2.5)
> > + * |
> > + * +-> ADCLK
> > + */
> > +
> > +struct ov5648_pll2_config {
> > + unsigned int plls_pre_div;
> > + unsigned int plls_div_r;
> > + unsigned int plls_mul;
> > + unsigned int sys_div;
> > + unsigned int sel_div;
> > +};
> > +
> > +/*
> > + * General formulas for (array-centered) mode calculation:
> > + * - photo_array_width = 2624
> > + * - crop_start_x = (photo_array_width - output_size_x) / 2
> > + * - crop_end_x = crop_start_x + offset_x + output_size_x - 1
> > + *
> > + * - photo_array_height = 1956
> > + * - crop_start_y = (photo_array_height - output_size_y) / 2
> > + * - crop_end_y = crop_start_y + offset_y + output_size_y - 1
> > + */
> > +
> > +struct ov5648_mode {
> > + unsigned int crop_start_x;
> > + unsigned int offset_x;
> > + unsigned int output_size_x;
> > + unsigned int crop_end_x;
> > + unsigned int hts;
> > +
> > + unsigned int crop_start_y;
> > + unsigned int offset_y;
> > + unsigned int output_size_y;
> > + unsigned int crop_end_y;
> > + unsigned int vts;
> > +
> > + bool binning_x;
> > + bool binning_y;
> > +
> > + unsigned int inc_x_odd;
> > + unsigned int inc_x_even;
> > + unsigned int inc_y_odd;
> > + unsigned int inc_y_even;
> > +
> > + /* 8-bit frame interval followed by 10-bit frame interval. */
> > + struct v4l2_fract frame_interval[2];
> > +
> > + /* 8-bit config followed by 10-bit config. */
> > + const struct ov5648_pll1_config *pll1_config[2];
> > + const struct ov5648_pll2_config *pll2_config;
> > +
> > + const struct ov5648_register_value *register_values;
> > + unsigned int register_values_count;
> > +};
> > +
> > +struct ov5648_state {
> > + const struct ov5648_mode *mode;
> > + u32 mbus_code;
> > +
> > + int power_count;
> > + bool streaming;
> > +};
> > +
> > +struct ov5648_ctrls {
> > + struct v4l2_ctrl *exposure_auto;
> > + struct v4l2_ctrl *exposure;
> > +
> > + struct v4l2_ctrl *gain_auto;
> > + struct v4l2_ctrl *gain;
> > +
> > + struct v4l2_ctrl *white_balance_auto;
> > + struct v4l2_ctrl *red_balance;
> > + struct v4l2_ctrl *blue_balance;
> > +
> > + struct v4l2_ctrl *flip_horz;
> > + struct v4l2_ctrl *flip_vert;
> > +
> > + struct v4l2_ctrl *test_pattern;
> > +
> > + struct v4l2_ctrl *link_freq;
> > + struct v4l2_ctrl *pixel_rate;
>
> If you don't need these pointers, do not keep them around. At least some
> are unused.
Understood, I'll remove the ones that are not needed.
> > +
> > + struct v4l2_ctrl_handler handler;
> > +} __packed;
>
> Why packed?
This is necessary because v4l2_ctrl_auto_cluster takes a pointer to an array
of struct v4l2_ctrl pointers. Here we don't actually have an array but following
elements in a structure, so we need to make sure that there is no gap between
elements for the two to be equivalent. Note that I've also put the handler
structure at the end to still have a good chance that things remain word-aligned
so there's no actual overhead due to unaligned access.
Thoguh I'll remove it from the OV8865 driver since we're not using
v4l2_ctrl_auto_cluster there.
> > +struct ov5648_sensor {
> > + struct device *dev;
> > + struct i2c_client *i2c_client;
> > + struct gpio_desc *reset;
> > + struct gpio_desc *powerdown;
> > + struct regulator *avdd;
> > + struct regulator *dvdd;
> > + struct regulator *dovdd;
> > + struct clk *xvclk;
> > +
> > + struct v4l2_fwnode_endpoint endpoint;
> > + struct v4l2_subdev subdev;
> > + struct media_pad pad;
> > +
> > + struct mutex mutex;
> > +
> > + struct ov5648_state state;
> > + struct ov5648_ctrls ctrls;
> > +};
> > +
> > +/* Static definitions */
> > +
> > +/*
> > + * XVCLK = 24 MHz
> > + * SCLK = 84 MHz
> > + * PCLK = 84 MHz
> > + */
> > +static const struct ov5648_pll1_config ov5648_pll1_config_native_8_bits = {
> > + .pll_pre_div = 3,
> > + .pll_mul = 84,
> > + .sys_div = 2,
> > + .root_div = 1,
> > + .sclk_div = 1,
> > + .mipi_div = 1,
> > +};
> > +
> > +/*
> > + * XVCLK = 24 MHz
> > + * SCLK = 84 MHz
> > + * PCLK = 84 MHz
> > + */
> > +static const struct ov5648_pll1_config ov5648_pll1_config_native_10_bits = {
> > + .pll_pre_div = 3,
> > + .pll_mul = 105,
> > + .sys_div = 2,
> > + .root_div = 1,
> > + .sclk_div = 1,
> > + .mipi_div = 1,
> > +};
> > +
> > +/*
> > + * XVCLK = 24 MHz
> > + * ADCLK = 200 MHz
> > + */
> > +static const struct ov5648_pll2_config ov5648_pll2_config_native = {
> > + .plls_pre_div = 3,
> > + .plls_div_r = 1,
> > + .plls_mul = 25,
> > + .sys_div = 1,
> > + .sel_div = 1,
> > +};
> > +
> > +static const struct ov5648_mode ov5648_mode_qsxga = {
> > + /* Horizontal */
> > + .crop_start_x = 16,
> > + .offset_x = 0,
> > + .output_size_x = 2592,
> > + .crop_end_x = 2607,
> > + .hts = 2816,
> > +
> > + /* Vertical */
> > + .crop_start_y = 6,
> > + .offset_y = 0,
> > + .output_size_y = 1944,
> > + .crop_end_y = 1949,
> > + .vts = 1984,
> > +
> > + /* Subsample increase */
> > + .inc_x_odd = 1,
> > + .inc_x_even = 1,
> > + .inc_y_odd = 1,
> > + .inc_y_even = 1,
> > +
> > + /* Frame Interval */
> > + .frame_interval = {
> > + { 1, 15 },
> > + { 1, 15 },
> > + },
> > +
> > + /* PLL */
> > + .pll1_config = {
> > + &ov5648_pll1_config_native_8_bits,
> > + &ov5648_pll1_config_native_10_bits,
> > + },
> > + .pll2_config = &ov5648_pll2_config_native,
> > +};
> > +
> > +static const struct ov5648_mode ov5648_mode_uxga = {
> > + /* Horizontal */
> > + .crop_start_x = 512,
> > + .offset_x = 0,
> > + .output_size_x = 1600,
> > + .crop_end_x = 2111,
> > + .hts = 2816,
> > +
> > + /* Vertical */
> > + .crop_start_y = 378,
> > + .offset_y = 0,
> > + .output_size_y = 1200,
> > + .crop_end_y = 1577,
> > + .vts = 1984,
> > +
> > + /* Subsample increase */
> > + .inc_x_odd = 1,
> > + .inc_x_even = 1,
> > + .inc_y_odd = 1,
> > + .inc_y_even = 1,
> > +
> > + /* Frame Interval */
> > + .frame_interval = {
> > + { 1, 15 },
> > + { 1, 15 },
> > + },
> > +
> > + /* PLL */
> > + .pll1_config = {
> > + &ov5648_pll1_config_native_8_bits,
> > + &ov5648_pll1_config_native_10_bits,
> > + },
> > + .pll2_config = &ov5648_pll2_config_native,
> > +};
> > +
> > +static const struct ov5648_mode ov5648_mode_1080p = {
> > + /* Horizontal */
> > + .crop_start_x = 352,
> > + .offset_x = 0,
> > + .output_size_x = 1920,
> > + .crop_end_x = 2271,
> > + .hts = 2816,
> > +
> > + /* Vertical */
> > + .crop_start_y = 438,
> > + .offset_y = 0,
> > + .output_size_y = 1080,
> > + .crop_end_y = 1517,
> > + .vts = 1984,
> > +
> > + /* Subsample increase */
> > + .inc_x_odd = 1,
> > + .inc_x_even = 1,
> > + .inc_y_odd = 1,
> > + .inc_y_even = 1,
> > +
> > + /* Frame Interval */
> > + .frame_interval = {
> > + { 1, 15 },
> > + { 1, 15 },
> > + },
> > +
> > + /* PLL */
> > + .pll1_config = {
> > + &ov5648_pll1_config_native_8_bits,
> > + &ov5648_pll1_config_native_10_bits,
> > + },
> > + .pll2_config = &ov5648_pll2_config_native,
> > +};
> > +
> > +static const struct ov5648_mode ov5648_mode_1280x960 = {
> > + /* From gf ref */
> > + /* Horizontal */
> > + .crop_start_x = 16,
> > + .offset_x = 8,
> > + .output_size_x = 1280,
> > + .crop_end_x = 2607,
> > + .hts = 1912,
> > +
> > + /* Vertical */
> > + .crop_start_y = 6,
> > + .offset_y = 6,
> > + .output_size_y = 960,
> > + .crop_end_y = 1949,
> > + .vts = 1496,
> > +
> > + /* Binning */
> > + .binning_x = true,
> > +
> > + /* Subsample increase */
> > + .inc_x_odd = 3,
> > + .inc_x_even = 1,
> > + .inc_y_odd = 3,
> > + .inc_y_even = 1,
> > +
> > + /* Frame Interval */
> > + .frame_interval = {
> > + { 1, 30 },
> > + { 1, 30 },
> > + },
> > +
> > + /* PLL */
> > + .pll1_config = {
> > + &ov5648_pll1_config_native_8_bits,
> > + &ov5648_pll1_config_native_10_bits,
> > + },
> > + .pll2_config = &ov5648_pll2_config_native,
> > +};
> > +
> > +static const struct ov5648_mode ov5648_mode_720p = {
> > + /* From gf ref */
> > + /* Horizontal */
> > + .crop_start_x = 16,
> > + .offset_x = 8,
> > + .output_size_x = 1280,
> > + .crop_end_x = 2607,
> > + .hts = 1912,
> > +
> > + /* Vertical */
> > + .crop_start_y = 254,
> > + .offset_y = 2,
> > + .output_size_y = 720,
> > + .crop_end_y = 1701,
> > + .vts = 1496,
> > +
> > + /* Binning */
> > + .binning_x = true,
> > +
> > + /* Subsample increase */
> > + .inc_x_odd = 3,
> > + .inc_x_even = 1,
> > + .inc_y_odd = 3,
> > + .inc_y_even = 1,
> > +
> > + /* Frame Interval */
> > + .frame_interval = {
> > + { 1, 30 },
> > + { 1, 30 },
> > + },
> > +
> > + /* PLL */
> > + .pll1_config = {
> > + &ov5648_pll1_config_native_8_bits,
> > + &ov5648_pll1_config_native_10_bits,
> > + },
> > + .pll2_config = &ov5648_pll2_config_native,
> > +};
> > +
> > +static const struct ov5648_mode ov5648_mode_vga = {
> > + /* From gf ref */
> > + /* Horizontal */
> > + .crop_start_x = 0,
> > + .offset_x = 8,
> > + .output_size_x = 640,
> > + .crop_end_x = 2623,
> > + .hts = 1896,
> > +
> > + /* Vertical */
> > + .crop_start_y = 0,
> > + .offset_y = 2,
> > + .output_size_y = 480,
> > + .crop_end_y = 1953,
> > + .vts = 984,
> > +
> > + /* Binning */
> > + .binning_x = true,
> > +
> > + /* Subsample increase */
> > + .inc_x_odd = 7,
> > + .inc_x_even = 1,
> > + .inc_y_odd = 7,
> > + .inc_y_even = 1,
> > +
> > + /* Frame Interval */
> > + .frame_interval = {
> > + { 1, 30 },
> > + { 1, 30 },
> > + },
> > +
> > + /* PLL */
> > + .pll1_config = {
> > + &ov5648_pll1_config_native_8_bits,
> > + &ov5648_pll1_config_native_10_bits,
> > + },
> > + .pll2_config = &ov5648_pll2_config_native,
> > +};
> > +
> > +static const struct ov5648_mode *ov5648_modes[] = {
> > + &ov5648_mode_qsxga,
> > + &ov5648_mode_uxga,
> > + &ov5648_mode_1080p,
> > + &ov5648_mode_1280x960,
> > + &ov5648_mode_720p,
> > + &ov5648_mode_vga,
> > +};
> > +
> > +static const u32 ov5648_mbus_codes[] = {
> > + MEDIA_BUS_FMT_SBGGR8_1X8,
> > + MEDIA_BUS_FMT_SBGGR10_1X10,
> > +};
> > +
> > +static const struct ov5648_register_value ov5648_init_sequence[] = {
> > + /* PSRAM */
> > + { OV5648_PSRAM_CTRL1_REG, 0x0d },
> > + { OV5648_PSRAM_CTRLF_REG, 0xf5 },
> > +};
> > +
> > +static const s64 ov5648_link_freq_menu[] = {
> > + 210000000,
> > + 168000000,
> > +};
> > +
> > +static const char *const ov5648_test_pattern_menu[] = {
> > + "Disabled",
> > + "Random data",
> > + "Color bars",
> > + "Color bars with rolling bar",
> > + "Color squares",
> > + "Color squares with rolling bar"
> > +};
> > +
> > +static const u8 ov5648_test_pattern_bits[] = {
> > + 0,
> > + OV5648_ISP_CTRL3D_PATTERN_EN | OV5648_ISP_CTRL3D_PATTERN_RANDOM_DATA,
> > + OV5648_ISP_CTRL3D_PATTERN_EN | OV5648_ISP_CTRL3D_PATTERN_COLOR_BARS,
> > + OV5648_ISP_CTRL3D_PATTERN_EN | OV5648_ISP_CTRL3D_ROLLING_BAR_EN |
> > + OV5648_ISP_CTRL3D_PATTERN_COLOR_BARS,
> > + OV5648_ISP_CTRL3D_PATTERN_EN | OV5648_ISP_CTRL3D_PATTERN_COLOR_SQUARES,
> > + OV5648_ISP_CTRL3D_PATTERN_EN | OV5648_ISP_CTRL3D_ROLLING_BAR_EN |
> > + OV5648_ISP_CTRL3D_PATTERN_COLOR_SQUARES,
> > +};
> > +
> > +/* Input/Output */
> > +
> > +static int ov5648_read(struct ov5648_sensor *sensor, u16 address, u8 *value)
> > +{
> > + unsigned char data[2] = { address >> 8, address & 0xff };
> > + struct i2c_client *client = sensor->i2c_client;
> > + int ret;
> > +
> > + ret = i2c_master_send(client, data, sizeof(data));
> > + if (ret < 0) {
> > + dev_dbg(&client->dev, "i2c send error at address %#04x\n",
> > + address);
> > + return ret;
> > + }
> > +
> > + ret = i2c_master_recv(client, value, 1);
> > + if (ret < 0) {
> > + dev_dbg(&client->dev, "i2c recv error at address %#04x\n",
> > + address);
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_write(struct ov5648_sensor *sensor, u16 address, u8 value)
> > +{
> > + unsigned char data[3] = { address >> 8, address & 0xff, value };
> > + struct i2c_client *client = sensor->i2c_client;
> > + int ret;
> > +
> > + ret = i2c_master_send(client, data, sizeof(data));
> > + if (ret < 0) {
> > + dev_dbg(&client->dev, "i2c send error at address %#04x\n",
> > + address);
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_write_sequence(struct ov5648_sensor *sensor,
> > + const struct ov5648_register_value *sequence,
> > + unsigned int sequence_count)
> > +{
> > + unsigned int i;
> > + int ret = 0;
> > +
> > + for (i = 0; i < sequence_count; i++) {
> > + ret = ov5648_write(sensor, sequence[i].address,
> > + sequence[i].value);
> > + if (ret)
> > + break;
> > +
> > + if (sequence[i].delay_ms)
> > + msleep(sequence[i].delay_ms);
> > + }
> > +
> > + return ret;
> > +}
> > +
> > +static int ov5648_update_bits(struct ov5648_sensor *sensor, u16 address,
> > + u8 mask, u8 bits)
> > +{
> > + u8 value = 0;
> > + int ret;
> > +
> > + ret = ov5648_read(sensor, address, &value);
> > + if (ret)
> > + return ret;
> > +
> > + value &= ~mask;
> > + value |= bits;
> > +
> > + ret = ov5648_write(sensor, address, value);
> > + if (ret)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +/* Sensor */
> > +
> > +static int ov5648_sw_reset(struct ov5648_sensor *sensor)
> > +{
> > + int ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_SW_RESET_REG, OV5648_SW_RESET_RESET);
> > + if (ret < 0)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_sw_standby(struct ov5648_sensor *sensor, int standby)
> > +{
> > + u8 value = 0;
> > + int ret;
> > +
> > + if (!standby)
> > + value = OV5648_SW_STANDBY_STREAM_ON;
> > +
> > + ret = ov5648_write(sensor, OV5648_SW_STANDBY_REG, value);
> > + if (ret < 0)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_chip_id_check(struct ov5648_sensor *sensor)
> > +{
> > + u16 regs[] = { OV5648_CHIP_ID_H_REG, OV5648_CHIP_ID_L_REG };
> > + u8 values[] = { OV5648_CHIP_ID_H_VALUE, OV5648_CHIP_ID_L_VALUE };
> > + unsigned int i;
> > + u8 value;
> > + int ret;
> > +
> > + for (i = 0; i < ARRAY_SIZE(regs); i++) {
> > + ret = ov5648_read(sensor, regs[i], &value);
> > + if (ret < 0)
> > + return ret;
> > +
> > + if (value != values[i]) {
> > + dev_err(sensor->dev,
> > + "chip id value mismatch: %#x instead of %#x\n",
> > + value, values[i]);
> > + return -EINVAL;
> > + }
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_avdd_internal_power(struct ov5648_sensor *sensor, int on)
> > +{
> > + int ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_A_PWC_PK_O0_REG,
> > + on ? 0 : OV5648_A_PWC_PK_O0_BP_REGULATOR_N);
> > + if (ret)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_pad_configure(struct ov5648_sensor *sensor)
> > +{
> > + int ret;
> > +
> > + /* Configure pads as input. */
> > +
> > + ret = ov5648_write(sensor, OV5648_PAD_OEN1_REG, 0);
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_PAD_OEN2_REG, 0);
> > + if (ret)
> > + return ret;
> > +
> > + /* Disable FREX pin. */
> > +
> > + ret = ov5648_write(sensor, OV5648_PAD_PK_REG,
> > + OV5648_PAD_PK_DRIVE_STRENGTH_1X |
> > + OV5648_PAD_PK_FREX_N);
> > + if (ret)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_mipi_configure(struct ov5648_sensor *sensor)
> > +{
> > + struct v4l2_fwnode_bus_mipi_csi2 *bus_mipi_csi2 =
> > + &sensor->endpoint.bus.mipi_csi2;
> > + unsigned int lanes_count = bus_mipi_csi2->num_data_lanes;
> > + int ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_MIPI_CTRL0_REG,
> > + OV5648_MIPI_CTRL0_CLK_LANE_AUTOGATE |
> > + OV5648_MIPI_CTRL0_LANE_SELECT_LANE1 |
> > + OV5648_MIPI_CTRL0_IDLE_LP11);
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_MIPI_SC_CTRL0_REG,
> > + OV5648_MIPI_SC_CTRL0_MIPI_LANES(lanes_count) |
> > + OV5648_MIPI_SC_CTRL0_PHY_LP_RX_PD |
> > + OV5648_MIPI_SC_CTRL0_MIPI_EN);
> > + if (ret)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_black_level_configure(struct ov5648_sensor *sensor)
> > +{
> > + int ret;
> > +
> > + /* Up to 6 lines are available for black level calibration. */
> > +
> > + ret = ov5648_write(sensor, OV5648_BLC_CTRL1_REG,
> > + OV5648_BLC_CTRL1_START_LINE(2));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_BLC_CTRL2_REG,
> > + OV5648_BLC_CTRL2_AUTO_EN |
> > + OV5648_BLC_CTRL2_RESET_FRAME_NUM(5));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_BLC_LINE_NUM_REG,
> > + OV5648_BLC_LINE_NUM(4));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_update_bits(sensor, OV5648_BLC_CTRL5_REG,
> > + OV5648_BLC_CTRL5_UPDATE_EN,
> > + OV5648_BLC_CTRL5_UPDATE_EN);
> > + if (ret)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_isp_configure(struct ov5648_sensor *sensor)
> > +{
> > + u8 bits;
> > + int ret;
> > +
> > + /* Enable black and white level correction. */
> > + bits = OV5648_ISP_CTRL0_BLACK_CORRECT_EN |
> > + OV5648_ISP_CTRL0_WHITE_CORRECT_EN;
> > +
> > + ret = ov5648_update_bits(sensor, OV5648_ISP_CTRL0_REG, bits, bits);
> > + if (ret)
> > + return ret;
> > +
> > + /* Enable AWB. */
> > + ret = ov5648_write(sensor, OV5648_ISP_CTRL1_REG,
> > + OV5648_ISP_CTRL1_AWB_EN);
> > + if (ret)
> > + return ret;
> > +
> > + /* Enable AWB gain and windowing. */
> > + ret = ov5648_write(sensor, OV5648_ISP_CTRL2_REG,
> > + OV5648_ISP_CTRL2_WIN_EN |
> > + OV5648_ISP_CTRL2_AWB_GAIN_EN);
> > + if (ret)
> > + return ret;
> > +
> > + /* Enable buffering and auto-binning. */
> > + ret = ov5648_write(sensor, OV5648_ISP_CTRL3_REG,
> > + OV5648_ISP_CTRL3_BUF_EN |
> > + OV5648_ISP_CTRL3_BIN_AUTO_EN);
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_ISP_CTRL4_REG, 0);
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_ISP_CTRL1F_REG,
> > + OV5648_ISP_CTRL1F_OUTPUT_EN);
> > + if (ret)
> > + return ret;
> > +
> > + /* Enable post-binning filters. */
> > + ret = ov5648_write(sensor, OV5648_ISP_CTRL4B_REG,
> > + OV5648_ISP_CTRL4B_POST_BIN_H_EN |
> > + OV5648_ISP_CTRL4B_POST_BIN_V_EN);
> > + if (ret)
> > + return ret;
> > +
> > + /* Disable debanding and night mode. Debug bit seems necessary. */
> > + ret = ov5648_write(sensor, OV5648_AEC_CTRL0_REG,
> > + OV5648_AEC_CTRL0_DEBUG |
> > + OV5648_AEC_CTRL0_START_SEL_EN);
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_MANUAL_CTRL_REG,
> > + OV5648_MANUAL_CTRL_FRAME_DELAY(1));
> > + if (ret)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +static unsigned long ov5648_mode_pll1_rate(struct ov5648_sensor *sensor,
> > + const struct ov5648_pll1_config *config)
> > +{
> > + unsigned long xvclk_rate;
> > + unsigned long pll1_rate;
> > +
> > + xvclk_rate = clk_get_rate(sensor->xvclk);
> > + pll1_rate = xvclk_rate * config->pll_mul;
> > +
> > + switch (config->pll_pre_div) {
> > + case 5:
> > + pll1_rate *= 3;
> > + pll1_rate /= 2;
> > + break;
> > + case 7:
> > + pll1_rate *= 5;
> > + pll1_rate /= 2;
> > + break;
> > + default:
> > + pll1_rate /= config->pll_pre_div;
> > + break;
> > + }
> > +
> > + return pll1_rate;
> > +}
> > +
> > +static int ov5648_mode_pll1_configure(struct ov5648_sensor *sensor,
> > + const struct ov5648_mode *mode,
> > + u32 mbus_code)
> > +{
> > + const struct ov5648_pll1_config *config;
> > + u8 value;
> > + int ret;
> > +
> > + value = OV5648_PLL_CTRL0_PLL_CHARGE_PUMP(1);
> > +
> > + switch (mbus_code) {
> > + case MEDIA_BUS_FMT_SBGGR8_1X8:
> > + config = mode->pll1_config[0];
> > + value |= OV5648_PLL_CTRL0_BITS(8);
> > + break;
> > + case MEDIA_BUS_FMT_SBGGR10_1X10:
> > + config = mode->pll1_config[1];
> > + value |= OV5648_PLL_CTRL0_BITS(10);
> > + break;
> > + default:
> > + return -EINVAL;
> > + }
> > +
> > + ret = ov5648_write(sensor, OV5648_PLL_CTRL0_REG, value);
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_PLL_DIV_REG,
> > + OV5648_PLL_DIV_ROOT_DIV(config->root_div) |
> > + OV5648_PLL_DIV_PLL_PRE_DIV(config->pll_pre_div));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_PLL_MUL_REG,
> > + OV5648_PLL_MUL(config->pll_mul));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_PLL_CTRL1_REG,
> > + OV5648_PLL_CTRL1_SYS_DIV(config->sys_div) |
> > + OV5648_PLL_CTRL1_MIPI_DIV(config->mipi_div));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_SRB_CTRL_REG,
> > + OV5648_SRB_CTRL_SCLK_DIV(config->sclk_div) |
> > + OV5648_SRB_CTRL_SCLK_ARBITER_EN);
> > + if (ret)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_mode_pll2_configure(struct ov5648_sensor *sensor,
> > + const struct ov5648_mode *mode)
> > +{
> > + const struct ov5648_pll2_config *config = mode->pll2_config;
> > + int ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_PLLS_DIV_REG,
> > + OV5648_PLLS_DIV_PLLS_PRE_DIV(config->plls_pre_div) |
> > + OV5648_PLLS_DIV_PLLS_DIV_R(config->plls_div_r) |
> > + OV5648_PLLS_DIV_PLLS_SEL_DIV(config->sel_div));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_PLLS_MUL_REG,
> > + OV5648_PLLS_MUL(config->plls_mul));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_PLLS_CTRL_REG,
> > + OV5648_PLLS_CTRL_PLL_CHARGE_PUMP(1) |
> > + OV5648_PLLS_CTRL_SYS_DIV(config->sys_div));
> > + if (ret)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_mode_configure(struct ov5648_sensor *sensor,
> > + const struct ov5648_mode *mode, u32 mbus_code)
> > +{
> > + int ret;
> > +
> > + /* Crop Start X */
> > +
> > + ret = ov5648_write(sensor, OV5648_CROP_START_X_H_REG,
> > + OV5648_CROP_START_X_H(mode->crop_start_x));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_CROP_START_X_L_REG,
> > + OV5648_CROP_START_X_L(mode->crop_start_x));
> > + if (ret)
> > + return ret;
> > +
> > + /* Offset X */
> > +
> > + ret = ov5648_write(sensor, OV5648_OFFSET_X_H_REG,
> > + OV5648_OFFSET_X_H(mode->offset_x));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_OFFSET_X_L_REG,
> > + OV5648_OFFSET_X_L(mode->offset_x));
> > + if (ret)
> > + return ret;
> > +
> > + /* Output Size X */
> > +
> > + ret = ov5648_write(sensor, OV5648_OUTPUT_SIZE_X_H_REG,
> > + OV5648_OUTPUT_SIZE_X_H(mode->output_size_x));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_OUTPUT_SIZE_X_L_REG,
> > + OV5648_OUTPUT_SIZE_X_L(mode->output_size_x));
> > + if (ret)
> > + return ret;
> > +
> > + /* Crop End X */
> > +
> > + ret = ov5648_write(sensor, OV5648_CROP_END_X_H_REG,
> > + OV5648_CROP_END_X_H(mode->crop_end_x));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_CROP_END_X_L_REG,
> > + OV5648_CROP_END_X_L(mode->crop_end_x));
> > + if (ret)
> > + return ret;
> > +
> > + /* Horizontal Total Size */
> > +
> > + ret = ov5648_write(sensor, OV5648_HTS_H_REG, OV5648_HTS_H(mode->hts));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_HTS_L_REG, OV5648_HTS_L(mode->hts));
> > + if (ret)
> > + return ret;
> > +
> > + /* Crop Start Y */
> > +
> > + ret = ov5648_write(sensor, OV5648_CROP_START_Y_H_REG,
> > + OV5648_CROP_START_Y_H(mode->crop_start_y));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_CROP_START_Y_L_REG,
> > + OV5648_CROP_START_Y_L(mode->crop_start_y));
> > + if (ret)
> > + return ret;
> > +
> > + /* Offset Y */
> > +
> > + ret = ov5648_write(sensor, OV5648_OFFSET_Y_H_REG,
> > + OV5648_OFFSET_Y_H(mode->offset_y));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_OFFSET_Y_L_REG,
> > + OV5648_OFFSET_Y_L(mode->offset_y));
> > + if (ret)
> > + return ret;
> > +
> > + /* Output Size Y */
> > +
> > + ret = ov5648_write(sensor, OV5648_OUTPUT_SIZE_Y_H_REG,
> > + OV5648_OUTPUT_SIZE_Y_H(mode->output_size_y));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_OUTPUT_SIZE_Y_L_REG,
> > + OV5648_OUTPUT_SIZE_Y_L(mode->output_size_y));
> > + if (ret)
> > + return ret;
> > +
> > + /* Crop End Y */
> > +
> > + ret = ov5648_write(sensor, OV5648_CROP_END_Y_H_REG,
> > + OV5648_CROP_END_Y_H(mode->crop_end_y));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_CROP_END_Y_L_REG,
> > + OV5648_CROP_END_Y_L(mode->crop_end_y));
> > + if (ret)
> > + return ret;
> > +
> > + /* Vertical Total Size */
> > +
> > + ret = ov5648_write(sensor, OV5648_VTS_H_REG, OV5648_VTS_H(mode->vts));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_VTS_L_REG, OV5648_VTS_L(mode->vts));
> > + if (ret)
> > + return ret;
> > +
> > + /* Flip/Mirror/Binning */
> > +
> > + /*
> > + * A debug bit is enabled by default and needs to be cleared for
> > + * subsampling to work.
> > + */
> > + ret = ov5648_update_bits(sensor, OV5648_TC20_REG,
> > + OV5648_TC20_DEBUG |
> > + OV5648_TC20_BINNING_VERT_EN,
> > + mode->binning_y ? OV5648_TC20_BINNING_VERT_EN :
> > + 0);
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_update_bits(sensor, OV5648_TC21_REG,
> > + OV5648_TC21_BINNING_HORZ_EN,
> > + mode->binning_x ? OV5648_TC21_BINNING_HORZ_EN :
> > + 0);
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_SUB_INC_X_REG,
> > + OV5648_SUB_INC_X_ODD(mode->inc_x_odd) |
> > + OV5648_SUB_INC_X_EVEN(mode->inc_x_even));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_SUB_INC_Y_REG,
> > + OV5648_SUB_INC_Y_ODD(mode->inc_y_odd) |
> > + OV5648_SUB_INC_Y_EVEN(mode->inc_y_even));
> > + if (ret)
> > + return ret;
> > +
> > + /* PLLs */
> > +
> > + ret = ov5648_mode_pll1_configure(sensor, mode, mbus_code);
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_mode_pll2_configure(sensor, mode);
> > + if (ret)
> > + return ret;
> > +
> > + /* Extra registers */
> > +
> > + if (mode->register_values) {
> > + ret = ov5648_write_sequence(sensor, mode->register_values,
> > + mode->register_values_count);
> > + if (ret)
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static unsigned long ov5648_mode_mipi_clk_rate(struct ov5648_sensor *sensor,
> > + const struct ov5648_mode *mode,
> > + u32 mbus_code)
> > +{
> > + const struct ov5648_pll1_config *config;
> > + unsigned long pll1_rate;
> > + unsigned long mipi_clk_rate;
> > +
> > + switch (mbus_code) {
> > + case MEDIA_BUS_FMT_SBGGR8_1X8:
> > + config = mode->pll1_config[0];
> > + break;
> > + case MEDIA_BUS_FMT_SBGGR10_1X10:
> > + config = mode->pll1_config[1];
> > + break;
> > + default:
> > + return 0;
> > + }
> > +
> > + pll1_rate = ov5648_mode_pll1_rate(sensor, config);
> > + mipi_clk_rate = pll1_rate / config->sys_div / config->mipi_div / 2;
>
> You could return the result and omit mipi_clk_rate variable.
Sure!
> > +
> > + return mipi_clk_rate;
> > +}
> > +
> > +/* Exposure */
> > +
> > +static int ov5648_exposure_auto_configure(struct ov5648_sensor *sensor,
> > + bool enable)
> > +{
> > + int ret;
> > +
> > + ret = ov5648_update_bits(sensor, OV5648_MANUAL_CTRL_REG,
>
> Could you change this to return a value you don't need to further process?
>
> And then make the changes to other similar instances, too.
Mhh to be honest I don't really like the idea. The point of these functions
is to provide some abstraction between generic values (enable boolean) and the
registrer/bit values. Splitting the latter in two places (register name here
and bit value in the caller) makes things more difficult to understand and
defeats the purpose of these abstraction functions altogether (why not directly
call ov5648_update_bits instead of this function then)?
> > + OV5648_MANUAL_CTRL_AEC_MANUAL_EN,
> > + enable ? 0 : OV5648_MANUAL_CTRL_AEC_MANUAL_EN);
> > + if (ret)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_exposure_configure(struct ov5648_sensor *sensor, u32 exposure)
> > +{
> > + struct ov5648_ctrls *ctrls = &sensor->ctrls;
> > + int ret;
> > +
> > + if (ctrls->exposure_auto->val != V4L2_EXPOSURE_MANUAL)
> > + return -EINVAL;
> > +
> > + ret = ov5648_write(sensor, OV5648_EXPOSURE_CTRL_HH_REG,
> > + OV5648_EXPOSURE_CTRL_HH(exposure));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_EXPOSURE_CTRL_H_REG,
> > + OV5648_EXPOSURE_CTRL_H(exposure));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_EXPOSURE_CTRL_L_REG,
> > + OV5648_EXPOSURE_CTRL_L(exposure));
> > + if (ret)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_exposure_value(struct ov5648_sensor *sensor,
> > + u32 *exposure)
> > +{
> > + u8 exposure_hh = 0, exposure_h = 0, exposure_l = 0;
> > + int ret;
> > +
> > + ret = ov5648_read(sensor, OV5648_EXPOSURE_CTRL_HH_REG, &exposure_hh);
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_read(sensor, OV5648_EXPOSURE_CTRL_H_REG, &exposure_h);
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_read(sensor, OV5648_EXPOSURE_CTRL_L_REG, &exposure_l);
> > + if (ret)
> > + return ret;
> > +
> > + *exposure = OV5648_EXPOSURE_CTRL_HH_VALUE((u32)exposure_hh) |
> > + OV5648_EXPOSURE_CTRL_H_VALUE((u32)exposure_h) |
> > + OV5648_EXPOSURE_CTRL_L_VALUE((u32)exposure_l);
> > +
> > + return 0;
> > +}
> > +
> > +/* Gain */
> > +
> > +static int ov5648_gain_auto_configure(struct ov5648_sensor *sensor, bool enable)
> > +{
> > + int ret;
> > +
> > + ret = ov5648_update_bits(sensor, OV5648_MANUAL_CTRL_REG,
> > + OV5648_MANUAL_CTRL_AGC_MANUAL_EN,
> > + enable ? 0 : OV5648_MANUAL_CTRL_AGC_MANUAL_EN);
> > + if (ret)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_gain_configure(struct ov5648_sensor *sensor, u32 gain)
> > +{
> > + struct ov5648_ctrls *ctrls = &sensor->ctrls;
> > + int ret;
> > +
> > + if (ctrls->gain_auto->val)
> > + return -EINVAL;
> > +
> > + ret = ov5648_write(sensor, OV5648_GAIN_CTRL_H_REG,
> > + OV5648_GAIN_CTRL_H(gain));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_GAIN_CTRL_L_REG,
> > + OV5648_GAIN_CTRL_L(gain));
> > + if (ret)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_gain_value(struct ov5648_sensor *sensor, u32 *gain)
> > +{
> > + u8 gain_h = 0, gain_l = 0;
> > + int ret;
> > +
> > + ret = ov5648_read(sensor, OV5648_GAIN_CTRL_H_REG, &gain_h);
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_read(sensor, OV5648_GAIN_CTRL_L_REG, &gain_l);
> > + if (ret)
> > + return ret;
> > +
> > + *gain = OV5648_GAIN_CTRL_H_VALUE((u32)gain_h) |
> > + OV5648_GAIN_CTRL_L_VALUE((u32)gain_l);
> > +
> > + return 0;
> > +}
> > +
> > +/* White Balance */
> > +
> > +static int ov5648_white_balance_auto_configure(struct ov5648_sensor *sensor,
> > + bool enable)
> > +{
> > + int ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_AWB_CTRL_REG,
> > + enable ? 0 : OV5648_AWB_CTRL_GAIN_MANUAL_EN);
> > + if (ret)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_white_balance_configure(struct ov5648_sensor *sensor,
> > + u32 red_balance, u32 blue_balance)
> > +{
> > + struct ov5648_ctrls *ctrls = &sensor->ctrls;
> > + int ret;
> > +
> > + if (ctrls->white_balance_auto->val)
> > + return -EINVAL;
> > +
> > + ret = ov5648_write(sensor, OV5648_GAIN_RED_MAN_H_REG,
> > + OV5648_GAIN_RED_MAN_H(red_balance));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_GAIN_RED_MAN_L_REG,
> > + OV5648_GAIN_RED_MAN_L(red_balance));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_GAIN_BLUE_MAN_H_REG,
> > + OV5648_GAIN_BLUE_MAN_H(blue_balance));
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_GAIN_BLUE_MAN_L_REG,
> > + OV5648_GAIN_BLUE_MAN_L(blue_balance));
> > + if (ret)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +/* Flip */
> > +
> > +static int ov5648_flip_vert_configure(struct ov5648_sensor *sensor, bool enable)
> > +{
> > + u8 bits = OV5648_TC20_FLIP_VERT_ISP_EN |
> > + OV5648_TC20_FLIP_VERT_SENSOR_EN;
> > + int ret;
> > +
> > + ret = ov5648_update_bits(sensor, OV5648_TC20_REG, bits,
> > + enable ? bits : 0);
> > + if (ret)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_flip_horz_configure(struct ov5648_sensor *sensor, bool enable)
> > +{
> > + u8 bits = OV5648_TC21_FLIP_HORZ_ISP_EN |
> > + OV5648_TC21_FLIP_HORZ_SENSOR_EN;
> > + int ret;
> > +
> > + ret = ov5648_update_bits(sensor, OV5648_TC21_REG, bits,
> > + enable ? bits : 0);
> > + if (ret)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +/* Test Pattern */
> > +
> > +static int ov5648_test_pattern_configure(struct ov5648_sensor *sensor, u8 bits)
> > +{
> > + int ret;
> > +
> > + ret = ov5648_write(sensor, OV5648_ISP_CTRL3D_REG, bits);
> > + if (ret)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +/* State */
> > +
> > +static int ov5648_state_mipi_configure(struct ov5648_sensor *sensor,
> > + const struct ov5648_mode *mode,
> > + u32 mbus_code)
> > +{
> > + struct ov5648_ctrls *ctrls = &sensor->ctrls;
> > + struct v4l2_fwnode_bus_mipi_csi2 *bus_mipi_csi2 =
> > + &sensor->endpoint.bus.mipi_csi2;
> > + unsigned long mipi_clk_rate;
> > + unsigned int bits_per_sample;
> > + unsigned int lanes_count;
> > + unsigned int i;
> > + s64 mipi_pixel_rate;
> > +
> > + mipi_clk_rate = ov5648_mode_mipi_clk_rate(sensor, mode, mbus_code);
> > + if (!mipi_clk_rate)
> > + return -EINVAL;
> > +
> > + for (i = 0; i < ARRAY_SIZE(ov5648_link_freq_menu); i++) {
> > + s64 freq = ov5648_link_freq_menu[i];
> > +
> > + if (freq == mipi_clk_rate)
> > + break;
> > + }
> > +
> > + if (i == ARRAY_SIZE(ov5648_link_freq_menu)) {
> > + dev_err(sensor->dev,
> > + "failed to find %lu clk rate in link freq\n",
> > + mipi_clk_rate);
> > + } else {
> > + __v4l2_ctrl_s_ctrl(ctrls->link_freq, i);
> > + }
> > +
> > + switch (mbus_code) {
> > + case MEDIA_BUS_FMT_SBGGR8_1X8:
> > + bits_per_sample = 8;
> > + break;
> > + case MEDIA_BUS_FMT_SBGGR10_1X10:
> > + bits_per_sample = 10;
> > + break;
> > + default:
> > + return -EINVAL;
> > + }
> > +
> > + lanes_count = bus_mipi_csi2->num_data_lanes;
> > + mipi_pixel_rate = mipi_clk_rate * 2 * lanes_count / bits_per_sample;
> > +
> > + __v4l2_ctrl_s_ctrl_int64(ctrls->pixel_rate, mipi_pixel_rate);
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_state_configure(struct ov5648_sensor *sensor,
> > + const struct ov5648_mode *mode,
> > + u32 mbus_code)
> > +{
> > + int ret;
> > +
> > + if (sensor->state.streaming)
> > + return -EBUSY;
> > +
> > + /* State will be configured at first power on otherwise. */
> > + if (sensor->state.power_count > 0) {
> > + ret = ov5648_mode_configure(sensor, mode, mbus_code);
> > + if (ret)
> > + return ret;
> > + }
> > +
> > + ret = ov5648_state_mipi_configure(sensor, mode, mbus_code);
> > + if (ret)
> > + return ret;
> > +
> > + sensor->state.mode = mode;
> > + sensor->state.mbus_code = mbus_code;
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_state_init(struct ov5648_sensor *sensor)
> > +{
> > + return ov5648_state_configure(sensor, ov5648_modes[0],
> > + ov5648_mbus_codes[0]);
> > +}
> > +
> > +/* Sensor Base */
> > +
> > +static int ov5648_sensor_init(struct ov5648_sensor *sensor)
> > +{
> > + int ret;
> > +
> > + ret = ov5648_sw_reset(sensor);
> > + if (ret) {
> > + dev_err(sensor->dev, "failed to perform sw reset\n");
> > + return ret;
> > + }
> > +
> > + ret = ov5648_sw_standby(sensor, 1);
> > + if (ret) {
> > + dev_err(sensor->dev, "failed to set sensor standby\n");
> > + return ret;
> > + }
> > +
> > + ret = ov5648_chip_id_check(sensor);
> > + if (ret) {
> > + dev_err(sensor->dev, "failed to check sensor chip id\n");
> > + return ret;
> > + }
> > +
> > + ret = ov5648_avdd_internal_power(sensor, !sensor->avdd);
> > + if (ret) {
> > + dev_err(sensor->dev, "failed to set internal avdd power\n");
> > + return ret;
> > + }
> > +
> > + ret = ov5648_write_sequence(sensor, ov5648_init_sequence,
> > + ARRAY_SIZE(ov5648_init_sequence));
> > + if (ret) {
> > + dev_err(sensor->dev, "failed to write init sequence\n");
> > + return ret;
> > + }
> > +
> > + ret = ov5648_pad_configure(sensor);
> > + if (ret) {
> > + dev_err(sensor->dev, "failed to configure pad\n");
> > + return ret;
> > + }
> > +
> > + ret = ov5648_mipi_configure(sensor);
> > + if (ret) {
> > + dev_err(sensor->dev, "failed to configure MIPI\n");
> > + return ret;
> > + }
> > +
> > + ret = ov5648_isp_configure(sensor);
> > + if (ret) {
> > + dev_err(sensor->dev, "failed to configure ISP\n");
> > + return ret;
> > + }
> > +
> > + ret = ov5648_black_level_configure(sensor);
> > + if (ret) {
> > + dev_err(sensor->dev, "failed to configure black level\n");
> > + return ret;
> > + }
> > +
> > + /* Configure current mode. */
> > + ret = ov5648_state_configure(sensor, sensor->state.mode,
> > + sensor->state.mbus_code);
> > + if (ret) {
> > + dev_err(sensor->dev, "failed to configure state\n");
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_sensor_power(struct ov5648_sensor *sensor, bool on)
> > +{
> > + /* Keep initialized to zero for disable label. */
> > + int ret = 0;
> > +
> > + /*
> > + * General notes about the power sequence:
> > + * - power-down GPIO must be active (low) during power-on;
> > + * - reset GPIO state does not matter during power-on;
> > + * - XVCLK must be provided 1 ms before register access;
> > + * - 10 ms are needed between power-down deassert and register access.
> > + */
> > +
> > + /* Note that regulator-and-GPIO-based power is untested. */
> > + if (on) {
> > + gpiod_set_value_cansleep(sensor->reset, 1);
> > + gpiod_set_value_cansleep(sensor->powerdown, 1);
> > +
> > + ret = regulator_enable(sensor->dovdd);
> > + if (ret) {
> > + dev_err(sensor->dev,
> > + "failed to enable DOVDD regulator\n");
> > + goto disable;
> > + }
> > +
> > + if (sensor->avdd) {
> > + ret = regulator_enable(sensor->avdd);
> > + if (ret) {
> > + dev_err(sensor->dev,
> > + "failed to enable AVDD regulator\n");
> > + goto disable;
> > + }
> > + }
> > +
> > + ret = regulator_enable(sensor->dvdd);
> > + if (ret) {
> > + dev_err(sensor->dev,
> > + "failed to enable DVDD regulator\n");
> > + goto disable;
> > + }
> > +
> > + /* According to OV5648 power up diagram. */
> > + usleep_range(5000, 10000);
> > +
> > + ret = clk_prepare_enable(sensor->xvclk);
> > + if (ret) {
> > + dev_err(sensor->dev, "failed to enable XVCLK clock\n");
> > + goto disable;
> > + }
> > +
> > + gpiod_set_value_cansleep(sensor->reset, 0);
> > + gpiod_set_value_cansleep(sensor->powerdown, 0);
> > +
> > + usleep_range(20000, 25000);
> > + } else {
> > +disable:
> > + gpiod_set_value_cansleep(sensor->powerdown, 1);
> > + gpiod_set_value_cansleep(sensor->reset, 1);
> > +
> > + clk_disable_unprepare(sensor->xvclk);
> > +
> > + regulator_disable(sensor->dvdd);
> > +
> > + if (sensor->avdd)
> > + regulator_disable(sensor->avdd);
> > +
> > + regulator_disable(sensor->dovdd);
> > + }
> > +
> > + return ret;
> > +}
> > +
> > +/* Controls */
> > +
> > +static int ov5648_g_volatile_ctrl(struct v4l2_ctrl *ctrl)
> > +{
> > + struct v4l2_subdev *subdev = ov5648_ctrl_subdev(ctrl);
> > + struct ov5648_sensor *sensor = ov5648_subdev_sensor(subdev);
> > + struct ov5648_ctrls *ctrls = &sensor->ctrls;
> > + int ret;
> > +
> > + switch (ctrl->id) {
> > + case V4L2_CID_EXPOSURE_AUTO:
> > + ret = ov5648_exposure_value(sensor, &ctrls->exposure->val);
> > + if (ret)
> > + return ret;
> > + break;
> > + case V4L2_CID_AUTOGAIN:
> > + ret = ov5648_gain_value(sensor, &ctrls->gain->val);
> > + if (ret)
> > + return ret;
> > + break;
> > + default:
> > + return -EINVAL;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_s_ctrl(struct v4l2_ctrl *ctrl)
> > +{
> > + struct v4l2_subdev *subdev = ov5648_ctrl_subdev(ctrl);
> > + struct ov5648_sensor *sensor = ov5648_subdev_sensor(subdev);
> > + struct ov5648_state *state = &sensor->state;
> > + struct ov5648_ctrls *ctrls = &sensor->ctrls;
> > + bool enable;
> > + u8 bits;
> > + int ret;
> > +
> > + /* Wait for the sensor to be on before setting controls. */
> > + if (state->power_count == 0)
> > + return 0;
> > +
> > + switch (ctrl->id) {
> > + case V4L2_CID_EXPOSURE_AUTO:
> > + enable = ctrl->val == V4L2_EXPOSURE_AUTO;
> > +
> > + ret = ov5648_exposure_auto_configure(sensor, enable);
> > + if (ret)
> > + return ret;
> > +
> > + if (!enable && ctrls->exposure->is_new) {
> > + ret = ov5648_exposure_configure(sensor,
> > + ctrls->exposure->val);
> > + if (ret)
> > + return ret;
> > + }
> > + break;
> > + case V4L2_CID_AUTOGAIN:
> > + enable = !!ctrl->val;
> > +
> > + ret = ov5648_gain_auto_configure(sensor, enable);
> > + if (ret)
> > + return ret;
> > +
> > + if (!enable) {
> > + ret = ov5648_gain_configure(sensor, ctrls->gain->val);
> > + if (ret)
> > + return ret;
> > + }
> > + break;
> > + case V4L2_CID_AUTO_WHITE_BALANCE:
> > + enable = !!ctrl->val;
> > +
> > + ret = ov5648_white_balance_auto_configure(sensor, enable);
> > + if (ret)
> > + return ret;
> > +
> > + if (!enable) {
> > + ret = ov5648_white_balance_configure(sensor,
> > + ctrls->red_balance->val,
> > + ctrls->blue_balance->val);
> > + if (ret)
> > + return ret;
> > + }
> > + break;
> > + case V4L2_CID_HFLIP:
> > + enable = !!ctrl->val;
> > + return ov5648_flip_horz_configure(sensor, enable);
> > + case V4L2_CID_VFLIP:
> > + enable = !!ctrl->val;
> > + return ov5648_flip_vert_configure(sensor, enable);
> > + case V4L2_CID_TEST_PATTERN:
> > + bits = ov5648_test_pattern_bits[ctrl->val];
> > + return ov5648_test_pattern_configure(sensor, bits);
> > + default:
> > + return -EINVAL;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static const struct v4l2_ctrl_ops ov5648_ctrl_ops = {
> > + .g_volatile_ctrl = ov5648_g_volatile_ctrl,
> > + .s_ctrl = ov5648_s_ctrl,
> > +};
> > +
> > +static int ov5648_ctrls_init(struct ov5648_sensor *sensor)
> > +{
> > + struct ov5648_ctrls *ctrls = &sensor->ctrls;
> > + struct v4l2_ctrl_handler *handler = &ctrls->handler;
> > + const struct v4l2_ctrl_ops *ops = &ov5648_ctrl_ops;
> > + int ret;
> > +
> > + v4l2_ctrl_handler_init(handler, 32);
> > +
> > + /* Use our mutex for ctrl locking. */
> > + handler->lock = &sensor->mutex;
> > +
> > + /* Exposure */
> > +
> > + ctrls->exposure_auto = v4l2_ctrl_new_std_menu(handler, ops,
> > + V4L2_CID_EXPOSURE_AUTO,
> > + V4L2_EXPOSURE_MANUAL, 0,
> > + V4L2_EXPOSURE_AUTO);
> > +
> > + ctrls->exposure = v4l2_ctrl_new_std(handler, ops, V4L2_CID_EXPOSURE,
> > + 16, 1048575, 16, 512);
> > + ctrls->exposure->flags |= V4L2_CTRL_FLAG_VOLATILE;
> > +
> > + v4l2_ctrl_auto_cluster(2, &ctrls->exposure_auto, 1, true);
> > +
> > + /* Gain */
> > +
> > + ctrls->gain_auto = v4l2_ctrl_new_std(handler, ops, V4L2_CID_AUTOGAIN,
> > + 0, 1, 1, 1);
> > +
> > + ctrls->gain = v4l2_ctrl_new_std(handler, ops, V4L2_CID_GAIN, 16, 1023,
> > + 16, 16);
> > + ctrls->gain->flags |= V4L2_CTRL_FLAG_VOLATILE;
> > +
> > + v4l2_ctrl_auto_cluster(2, &ctrls->gain_auto, 0, true);
> > +
> > + /* White Balance */
> > +
> > + ctrls->white_balance_auto = v4l2_ctrl_new_std(handler, ops,
> > + V4L2_CID_AUTO_WHITE_BALANCE,
> > + 0, 1, 1, 1);
> > +
> > + ctrls->red_balance = v4l2_ctrl_new_std(handler, ops,
> > + V4L2_CID_RED_BALANCE, 0, 4095,
> > + 1, 1024);
> > +
> > + ctrls->blue_balance = v4l2_ctrl_new_std(handler, ops,
> > + V4L2_CID_BLUE_BALANCE, 0, 4095,
> > + 1, 1024);
> > +
> > + v4l2_ctrl_auto_cluster(3, &ctrls->white_balance_auto, 0, false);
> > +
> > + /* Flip */
> > +
> > + ctrls->flip_horz = v4l2_ctrl_new_std(handler, ops, V4L2_CID_HFLIP, 0, 1,
> > + 1, 0);
> > + ctrls->flip_vert = v4l2_ctrl_new_std(handler, ops, V4L2_CID_VFLIP, 0, 1,
> > + 1, 0);
> > +
> > + /* Test Pattern */
> > +
> > + ctrls->test_pattern =
> > + v4l2_ctrl_new_std_menu_items(handler, ops,
> > + V4L2_CID_TEST_PATTERN,
> > + ARRAY_SIZE(ov5648_test_pattern_menu) - 1,
> > + 0, 0, ov5648_test_pattern_menu);
> > +
> > + /* MIPI CSI-2 */
> > +
> > + ctrls->link_freq =
> > + v4l2_ctrl_new_int_menu(handler, ops, V4L2_CID_LINK_FREQ,
> > + ARRAY_SIZE(ov5648_link_freq_menu) - 1,
> > + 0, ov5648_link_freq_menu);
> > +
> > + ctrls->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY;
> > +
> > + ctrls->pixel_rate = v4l2_ctrl_new_std(handler, ops, V4L2_CID_PIXEL_RATE,
> > + 1, INT_MAX, 1, 1);
> > +
> > + ctrls->pixel_rate->flags |= V4L2_CTRL_FLAG_READ_ONLY;
> > +
> > + if (handler->error) {
> > + ret = handler->error;
> > + goto error_ctrls;
> > + }
> > +
> > + sensor->subdev.ctrl_handler = handler;
> > +
> > + return 0;
> > +
> > +error_ctrls:
> > + v4l2_ctrl_handler_free(handler);
> > +
> > + return ret;
> > +}
> > +
> > +/* Subdev Core Operations */
> > +
> > +static int ov5648_s_power(struct v4l2_subdev *subdev, int on)
>
> Please add support for runtime PM instead. See e.g. the ov8856 driver for
> an example.
Okay, I'll look into that.
> > +{
> > + struct ov5648_sensor *sensor = ov5648_subdev_sensor(subdev);
> > + struct ov5648_state *state = &sensor->state;
> > + bool ctrl_handler_setup = false;
> > + int ret = 0;
> > +
> > + mutex_lock(&sensor->mutex);
> > +
> > + state->power_count += on ? 1 : -1;
> > +
> > + /* Neither first power on nor last power off. */
> > + if (state->power_count != !!on)
> > + goto complete;
> > +
> > + ret = ov5648_sensor_power(sensor, on);
> > + if (ret)
> > + goto complete;
> > +
> > + /* First power on: init sensor and set controls. */
> > + if (on) {
> > + ret = ov5648_sensor_init(sensor);
> > + if (ret)
> > + goto error_power;
> > +
> > + ctrl_handler_setup = true;
> > + }
> > +
> > + goto complete;
> > +
> > +error_power:
> > + ov5648_sensor_power(sensor, !on);
> > +
> > +complete:
> > + mutex_unlock(&sensor->mutex);
> > +
> > + if (ctrl_handler_setup)
> > + ret = v4l2_ctrl_handler_setup(&sensor->ctrls.handler);
> > +
> > + return ret;
> > +}
> > +
> > +static const struct v4l2_subdev_core_ops ov5648_subdev_core_ops = {
> > + .s_power = ov5648_s_power,
> > +};
> > +
> > +/* Subdev Video Operations */
> > +
> > +static int ov5648_s_stream(struct v4l2_subdev *subdev, int enable)
> > +{
> > + struct ov5648_sensor *sensor = ov5648_subdev_sensor(subdev);
> > + int ret = 0;
> > +
> > + mutex_lock(&sensor->mutex);
> > +
> > + ret = ov5648_sw_standby(sensor, !enable);
> > + if (ret)
> > + goto complete;
> > +
> > + sensor->state.streaming = !!enable;
> > +
> > +complete:
> > + mutex_unlock(&sensor->mutex);
> > +
> > + return ret;
> > +}
> > +
> > +static int ov5648_g_frame_interval(struct v4l2_subdev *subdev,
> > + struct v4l2_subdev_frame_interval *interval)
> > +{
> > + struct ov5648_sensor *sensor = ov5648_subdev_sensor(subdev);
> > + const struct ov5648_mode *mode;
> > + int ret = 0;
> > +
> > + mutex_lock(&sensor->mutex);
> > +
> > + mode = sensor->state.mode;
> > +
> > + switch (sensor->state.mbus_code) {
> > + case MEDIA_BUS_FMT_SBGGR8_1X8:
> > + interval->interval = mode->frame_interval[0];
> > + break;
> > + case MEDIA_BUS_FMT_SBGGR10_1X10:
> > + interval->interval = mode->frame_interval[1];
> > + break;
> > + default:
> > + ret = -EINVAL;
> > + }
> > +
> > + mutex_unlock(&sensor->mutex);
> > +
> > + return ret;
> > +}
> > +
> > +static const struct v4l2_subdev_video_ops ov5648_subdev_video_ops = {
> > + .s_stream = ov5648_s_stream,
> > + .g_frame_interval = ov5648_g_frame_interval,
> > + .s_frame_interval = ov5648_g_frame_interval,
> > +};
> > +
> > +/* Subdev Pad Operations */
> > +
> > +static int ov5648_enum_mbus_code(struct v4l2_subdev *subdev,
> > + struct v4l2_subdev_pad_config *config,
> > + struct v4l2_subdev_mbus_code_enum *code_enum)
> > +{
> > + if (code_enum->index >= ARRAY_SIZE(ov5648_mbus_codes))
> > + return -EINVAL;
> > +
> > + code_enum->code = ov5648_mbus_codes[code_enum->index];
> > +
> > + return 0;
> > +}
> > +
> > +static void ov5648_mbus_format_fill(struct v4l2_mbus_framefmt *mbus_format,
> > + u32 mbus_code,
> > + const struct ov5648_mode *mode)
> > +{
> > + mbus_format->width = mode->output_size_x;
> > + mbus_format->height = mode->output_size_y;
> > + mbus_format->code = mbus_code;
> > +
> > + mbus_format->field = V4L2_FIELD_NONE;
> > + mbus_format->colorspace = V4L2_COLORSPACE_RAW;
> > + mbus_format->ycbcr_enc =
> > + V4L2_MAP_YCBCR_ENC_DEFAULT(mbus_format->colorspace);
> > + mbus_format->quantization = V4L2_QUANTIZATION_FULL_RANGE;
> > + mbus_format->xfer_func =
> > + V4L2_MAP_XFER_FUNC_DEFAULT(mbus_format->colorspace);
> > +}
> > +
> > +static int ov5648_get_fmt(struct v4l2_subdev *subdev,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_format *format)
> > +{
> > + struct ov5648_sensor *sensor = ov5648_subdev_sensor(subdev);
> > + struct v4l2_mbus_framefmt *mbus_format = &format->format;
> > +
> > + mutex_lock(&sensor->mutex);
> > +
> > + if (format->which == V4L2_SUBDEV_FORMAT_TRY) {
> > + *mbus_format =
> > + *v4l2_subdev_get_try_format(subdev, cfg, format->pad);
> > + } else {
> > + ov5648_mbus_format_fill(mbus_format, sensor->state.mbus_code,
> > + sensor->state.mode);
> > + }
> > +
> > + mutex_unlock(&sensor->mutex);
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_set_fmt(struct v4l2_subdev *subdev,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_format *format)
> > +{
> > + struct ov5648_sensor *sensor = ov5648_subdev_sensor(subdev);
> > + struct v4l2_mbus_framefmt *mbus_format = &format->format;
> > + const struct ov5648_mode *mode = ov5648_modes[0];
> > + u32 mbus_code = ov5648_mbus_codes[0];
> > + unsigned int index;
> > + int ret = 0;
> > +
> > + mutex_lock(&sensor->mutex);
> > +
> > + if (sensor->state.streaming) {
> > + ret = -EBUSY;
> > + goto complete;
> > + }
> > +
> > + /* Try to find requested mbus code. */
> > + for (index = 0; index < ARRAY_SIZE(ov5648_mbus_codes); index++) {
> > + if (ov5648_mbus_codes[index] == mbus_format->code) {
> > + mbus_code = mbus_format->code;
> > + break;
> > + }
> > + }
> > +
> > + /* Try to find requested mode code. */
> > + for (index = 0; index < ARRAY_SIZE(ov5648_modes); index++) {
> > + if (ov5648_modes[index]->output_size_x == mbus_format->width &&
> > + ov5648_modes[index]->output_size_y == mbus_format->height) {
>
> Please use the closest size. You can find that using
> v4l2_find_nearest_size().
Will do.
> > + mode = ov5648_modes[index];
> > + break;
> > + }
> > + }
> > +
> > + ov5648_mbus_format_fill(mbus_format, mbus_code, mode);
> > +
> > + if (format->which == V4L2_SUBDEV_FORMAT_TRY) {
> > + *v4l2_subdev_get_try_format(subdev, cfg, format->pad) =
> > + *mbus_format;
> > + } else if (sensor->state.mode != mode ||
> > + sensor->state.mbus_code != mbus_code) {
> > + ret = ov5648_state_configure(sensor, mode, mbus_code);
> > + if (ret)
> > + goto complete;
> > + }
> > +
> > +complete:
> > + mutex_unlock(&sensor->mutex);
> > +
> > + return ret;
> > +}
> > +
> > +static int ov5648_enum_frame_size(struct v4l2_subdev *subdev,
> > + struct v4l2_subdev_pad_config *config,
> > + struct v4l2_subdev_frame_size_enum *size_enum)
> > +{
> > + const struct ov5648_mode *mode;
> > +
> > + if (size_enum->index >= ARRAY_SIZE(ov5648_modes))
> > + return -EINVAL;
> > +
> > + mode = ov5648_modes[size_enum->index];
> > +
> > + size_enum->min_width = size_enum->max_width = mode->output_size_x;
> > + size_enum->min_height = size_enum->max_height = mode->output_size_y;
> > +
> > + return 0;
> > +}
> > +
> > +static int ov5648_enum_frame_interval(struct v4l2_subdev *subdev,
> > + struct v4l2_subdev_pad_config *config,
> > + struct v4l2_subdev_frame_interval_enum *interval_enum)
> > +{
> > + const struct ov5648_mode *mode = NULL;
> > + unsigned int mode_index;
> > + unsigned int interval_index;
> > +
> > + if (interval_enum->index > 0)
> > + return -EINVAL;
> > +
> > + /*
> > + * Multiple modes with the same dimensions may have different frame
> > + * intervals, so look up each relevant mode.
> > + */
> > + for (mode_index = 0, interval_index = 0;
> > + mode_index < ARRAY_SIZE(ov5648_modes); mode_index++) {
> > + mode = ov5648_modes[mode_index];
> > +
> > + if (mode->output_size_x == interval_enum->width &&
> > + mode->output_size_y == interval_enum->height) {
> > + if (interval_index == interval_enum->index)
> > + break;
> > +
> > + interval_index++;
> > + }
> > + }
> > +
> > + if (mode_index == ARRAY_SIZE(ov5648_modes) || !mode)
> > + return -EINVAL;
> > +
> > + switch (interval_enum->code) {
> > + case MEDIA_BUS_FMT_SBGGR8_1X8:
> > + interval_enum->interval = mode->frame_interval[0];
> > + break;
> > + case MEDIA_BUS_FMT_SBGGR10_1X10:
> > + interval_enum->interval = mode->frame_interval[1];
> > + break;
> > + default:
> > + return -EINVAL;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static const struct v4l2_subdev_pad_ops ov5648_subdev_pad_ops = {
> > + .enum_mbus_code = ov5648_enum_mbus_code,
> > + .get_fmt = ov5648_get_fmt,
> > + .set_fmt = ov5648_set_fmt,
> > + .enum_frame_size = ov5648_enum_frame_size,
> > + .enum_frame_interval = ov5648_enum_frame_interval,
> > +};
> > +
> > +static const struct v4l2_subdev_ops ov5648_subdev_ops = {
> > + .core = &ov5648_subdev_core_ops,
> > + .video = &ov5648_subdev_video_ops,
> > + .pad = &ov5648_subdev_pad_ops,
> > +};
> > +
> > +static int ov5648_probe(struct i2c_client *client)
> > +{
> > + struct device *dev = &client->dev;
> > + struct fwnode_handle *handle;
> > + struct ov5648_sensor *sensor;
> > + struct v4l2_subdev *subdev;
> > + struct media_pad *pad;
> > + int ret;
> > +
> > + sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL);
> > + if (!sensor)
> > + return -ENOMEM;
> > +
> > + sensor->dev = dev;
> > + sensor->i2c_client = client;
> > +
> > + /* Graph Endpoint */
> > +
> > + handle = fwnode_graph_get_next_endpoint(dev_fwnode(dev), NULL);
> > + if (!handle) {
> > + dev_err(dev, "unable to find enpoint node\n");
> > + return -EINVAL;
> > + }
> > +
> > + sensor->endpoint.bus_type = V4L2_MBUS_CSI2_DPHY;
> > +
> > + ret = v4l2_fwnode_endpoint_parse(handle, &sensor->endpoint);
> > + fwnode_handle_put(handle);
> > + if (ret) {
> > + dev_err(dev, "failed to parse endpoint node\n");
> > + return ret;
> > + }
> > +
> > + /* GPIOs */
> > +
> > + sensor->powerdown = devm_gpiod_get_optional(dev, "powerdown",
> > + GPIOD_OUT_HIGH);
> > + if (IS_ERR(sensor->powerdown))
> > + return PTR_ERR(sensor->powerdown);
> > +
> > + sensor->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
> > + if (IS_ERR(sensor->reset))
> > + return PTR_ERR(sensor->reset);
> > +
> > + /* Regulators */
> > +
> > + /* DVDD: digital core */
> > + sensor->dvdd = devm_regulator_get(dev, "dvdd");
> > + if (IS_ERR(sensor->dvdd)) {
> > + dev_err(dev, "cannot get DVDD (digital core) regulator\n");
> > + return PTR_ERR(sensor->dvdd);
> > + }
> > +
> > + /* DOVDD: digital I/O */
> > + sensor->dovdd = devm_regulator_get(dev, "dovdd");
> > + if (IS_ERR(sensor->dvdd)) {
> > + dev_err(dev, "cannot get DOVDD (digital I/O) regulator\n");
> > + return PTR_ERR(sensor->dvdd);
> > + }
> > +
> > + /* AVDD: analog */
> > + sensor->avdd = devm_regulator_get_optional(dev, "avdd");
> > + if (IS_ERR(sensor->avdd)) {
> > + dev_info(dev, "no AVDD regulator provided, using internal\n");
> > + sensor->avdd = NULL;
> > + }
> > +
> > + /* External Clock */
> > +
> > + sensor->xvclk = devm_clk_get(dev, "xvclk");
> > + if (IS_ERR(sensor->xvclk)) {
> > + dev_err(dev, "failed to get xvclk external clock\n");
> > + return PTR_ERR(sensor->xvclk);
> > + }
> > +
> > + ret = clk_set_rate_exclusive(sensor->xvclk, OV5648_XVCLK_RATE);
>
> The clock rate is specific to the driver, not to the device.
>
> If you rely on assigned-clock-rates, you'll need to get the frequency and
> compare that against what the driver can do, and fail if the driver doesn't
> support the frequency. I understand this is the preferred method nowadays.
Understood.
> > + if (ret) {
> > + dev_err(dev, "failed to set xvclk external clock rate\n");
> > + return ret;
> > + }
> > +
> > + /* Subdev, entity and pad */
> > +
> > + subdev = &sensor->subdev;
> > + v4l2_i2c_subdev_init(subdev, client, &ov5648_subdev_ops);
> > +
> > + subdev->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> > + subdev->entity.function = MEDIA_ENT_F_CAM_SENSOR;
> > +
> > + pad = &sensor->pad;
> > + pad->flags = MEDIA_PAD_FL_SOURCE;
> > +
> > + ret = media_entity_pads_init(&subdev->entity, 1, pad);
> > + if (ret)
> > + goto error_entity;
> > +
> > + /* Mutex */
> > +
> > + mutex_init(&sensor->mutex);
> > +
> > + /* Sensor */
> > +
> > + ret = ov5648_ctrls_init(sensor);
> > + if (ret)
> > + goto error_mutex;
> > +
> > + ret = ov5648_state_init(sensor);
> > + if (ret)
> > + goto error_ctrls;
> > +
> > + /* V4L2 subdev register */
> > +
> > + ret = v4l2_async_register_subdev_sensor_common(subdev);
> > + if (ret)
> > + goto error_ctrls;
> > +
> > + return 0;
> > +
> > +error_ctrls:
> > + v4l2_ctrl_handler_free(&sensor->ctrls.handler);
> > +
> > +error_mutex:
> > + mutex_destroy(&sensor->mutex);
> > +
> > +error_entity:
> > + media_entity_cleanup(&sensor->subdev.entity);
> > +
> > + return ret;
> > +}
> > +
> > +static int ov5648_remove(struct i2c_client *client)
> > +{
> > + struct v4l2_subdev *subdev = i2c_get_clientdata(client);
> > + struct ov5648_sensor *sensor = ov5648_subdev_sensor(subdev);
> > +
> > + clk_rate_exclusive_put(sensor->xvclk);
> > +
> > + v4l2_async_unregister_subdev(subdev);
> > + mutex_destroy(&sensor->mutex);
> > + media_entity_cleanup(&subdev->entity);
> > + v4l2_device_unregister_subdev(subdev);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct i2c_device_id ov5648_id[] = {
> > + { "ov5648", 0 },
>
> Please don't add I²C ID table unless you really need it. The OF match table
> is enough in general.
Sure, I'll remove it.
Thanks,
Paul
> > + { }
> > +};
> > +MODULE_DEVICE_TABLE(i2c, ov5648_id);
> > +
> > +static const struct of_device_id ov5648_of_match[] = {
> > + { .compatible = "ovti,ov5648" },
> > + { }
> > +};
> > +MODULE_DEVICE_TABLE(of, ov5648_of_match);
> > +
> > +static struct i2c_driver ov5648_driver = {
> > + .driver = {
> > + .of_match_table = ov5648_of_match,
> > + .name = "ov5648",
> > + },
> > + .probe_new = ov5648_probe,
> > + .remove = ov5648_remove,
> > + .id_table = ov5648_id,
> > +};
> > +
> > +module_i2c_driver(ov5648_driver);
> > +
> > +MODULE_AUTHOR("Paul Kocialkowski <paul.kocialkowski@...tlin.com>");
> > +MODULE_DESCRIPTION("V4L2 driver for the OmniVision OV5648 image sensor");
> > +MODULE_LICENSE("GPL v2");
>
> --
> Kind regards,
>
> Sakari Ailus
--
Paul Kocialkowski, Bootlin
Embedded Linux and kernel engineering
https://bootlin.com
Download attachment "signature.asc" of type "application/pgp-signature" (489 bytes)
Powered by blists - more mailing lists